AAT NVR-6332-H8/FR Instrukcja obsługi

User’ s ma n ual

(shor t )

NVR-6332-H8/FR

NVR-6332-H8/FR User’s manual (Short) ver.1.2

2

IMPORTANT SAFEGUARDS AND WARNINGS

THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING DIRECTIVES:

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self installation in households by

individuals without technical knowledge. The manufacturer is not responsible for defects and damages resulted from improper or

inconsistent with user’s manual installation of the device in the system.

ATTENTION!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT PROVISIONED FOR THE GIVEN PRODUCT IN ITS USER’S MANUAL AND OTHER DOCUMENTS

DELIVERED WITH THE PRODUCT, OR THAT ARISES FROM THE NORMAL APPLICATION OF THE PRODUCT, ITS MANUFACTURER MUST BE CONTACTED

OR THE RESPONSIBILITY OF THE MANUFACTURER FOR THE RESULTS OF SUCH AN ACTION SHELL BE EXCLUDED.

1. Prior to undertaking any action please consult the following manual and read all the safety and operating instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct influence on user’s safety and durability and

reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is forbidden;

7. You are not allowed to use the device in high humidity environment (i.e. close to swimming pools, bath tubs, damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not recommended since it may lead to heat

build-up and damaging the device itself as a consequence;

9. Mounting the device on unstable surface or using not recommended mounts is forbidden. Improperly mounted device may cause a fatal accident or

may be seriously damaged itself. The device must be mounted by qualied personnel with proper authorization, in accordance with this user’s

manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with those specied by the producer in the devices

technical datasheet. Therefore, it is forbidden to supply the devices from a power sources with unknown parameters, unstable or not meeting

producer’s requirements;

11. You cannot allow any metal objects get inside the recorder. It might cause serious damage. If a metal object gets inside the device contact the

authorised Novus service immediately.

12. The manufacturer does not bear responsibility for damage or loss of data stored on HDDs or other media occurred during the usage of the product.

Due to the product being constantly enhanced and optimized, certain parameters and functions described in the manual in question may change

without further notice.

We strongly suggest visiting the www.novuscctv.com website in order to access the newest manual .

Technical changes reserved without prior notice and printing errors possible.

DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIMENT AND OF THE

COUNCIL of 26 February 2014 on the harmonisation of the laws of the Member States

relating to electromagnetic compatibility (OJ L 96, 29.3.2014, p. 79–106, with changes)

DIRECTIVE 2014/35/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 26 February 2014 on the harmonization of the laws of the Member States

relating to the making available on the market of electrical equipment designed for use

within certain voltage limits.

DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 4 July 2012 on waste electrical and electronic equipment (WEEE) (OJ L

197, 24.7.2012, p. 38–71,with changes)

DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 8 June 2011 on the restriction of the use of certain hazardous substances in

electrical and electronic equipment (OJ L 174, 1.7.2011, p. 88–110, with changes)

NVR-6332-H8/FR User’s manual (Short) ver.1.2

3

FOREWORD INFORMATION

1. FOREWORD INFORMATION

1.1. Network recorder’s technical data

NVR-6332-H8/FR

Video

IP Cameras up to 32 channels at 3840 x 2160 resolution (video + audio)

Supported Resolution max. 3840 x 2160

Compression H.264, H.264+, H.265

Monitor Output main (split screen, full screen, sequence): 1 x VGA, 1 x HDMI (4K UltraHD)

Dualstreaming Support yes

Fisheye Support yes, 3000/6000 IP series cameras

Audio

Audio Output 1 x line-out (RCA) 1 x HDMI

Recording

Recording Speed 960 fps (32 x 30 fps for 3840 x 2160 and lower)

Stream Size 256 Mb/s in total from all cameras

Recording Mode time-lapse, triggered by: manual, alarm input, motion detection, intelligent image analysis functions

Prealarm/Postalarm up to 5 s/up to 600 s

Display

Display Speed 960 fps (32 x 30 fps)*

Playback

Playback Speed 480 fps (16 x 30 fps for 3840 x 2160) *

Recorded Data Search by date/time, events, motion in a defined area, related to face recognition

Backup

Backup Methods USB port (HDD or Flash memory), network

Backup File Format AVI, RPAS (player included)

Storage

Internal Storage available mount: 8 x HDD 3.5” 14 TB SATA

Total Internal Capacity 112 TB

RAID Mode RAID0, RAID1, RAID5, RAID6

Alarm

Internal Alarm Input/Output 8/4 relay type

Camera Alarm Input/Output supports camera’s alarm input/output

Motion Detection supports camera’s motion detection

System Reaction to Alarm buzzer, e-mail, alarm output activation, recording activation, PTZ

Intelligent image analysis

Supported Functions Exception, Scene Change, Video Blurred, Video Color Cast, Tripwire, Zone entrance, Abandoned Object, Object Di-

Network

Network Interface 2 x Ethernet - RJ-45 interface, 10/100/1000 Mbit/s

Network Protocols Support HTTP, TCP/IP, IPv4, HTTPS, FTP, DHCP, DNS, DDNS, NTP, RTSP, UPnP, SNMP, SMTP

ONVIF Protocol Support Profile S (ONVIF 2.2 or higher)

PC/MAC Software NMS, Internet Explorer, NVR-6000 Viewer/-

Mobile applications SuperLive Plus (iPhone, Android)

Number of Simultaneous Con-

nections

up to 4 clients

Bandwidth 256 Mb/s in total to all client workstations

PTZ

PTZ Functions pan/tilt/zoom, preset commands

Auxiliary Interfaces

USB Ports 2 x USB 2.0, 1 x USB 3.0

Operating system

Operating System Linux

OSD languages: Polish, English, others

Control PC mouse and IR remote controller (in-set included), network

System Diagnostic automatic control of: HDDs, network, camera connection loss

Security password protection, IP filtering, MAC filtering

Installation parameters

Dimensions (mm) 430 (W) x 90 (H) x 453 (D)

Weight 6 kg (without HDD)

Power Supply 100 ~ 240 VAC

Power Consumption 175 W (with 8 HDDs)

Operating Temperature -10°C ~ 50°C

RACK Mount 19" 2U

NVR-6332-H8/FR User’s manual (Short) ver.1.2

4

FOREWORD INFORMATION

1.2. Main characteristics

• Supports resolution up to 3840 x 2160

• Supported protocols: ONVIF

• Recording up to 3840 x 2160

• Recorded stream size up to 256 Mb/s in total from all cameras

• Mounting up to 8 drives inside - support for RAID0, RAID1, RAID5, RAID6, RADI10

• Fishsye camera support

• Face detection functions

• Internal HDDs mount up to 8

• 2 x Ethernet - RJ-45, 10/100/1000 Mbit/s

WARNING!

ONVIF protocol support was verified with IP cameras based on ONVIF ver. 2.2 and compatible

with the "PROFILE S".

Implementation of the ONVIF protocol by different manufacturers may vary by some functions,

which can make them work improperly or not in accordance with expectation. AAT SYSTEMY

BEZPIECZEŃSTWA SP. Z O.O. is not responsible for incompatibility problems resulting from

cameras of other brands than NOVUS, which are using ONVIF protocol. If you are using

ONVIF protocol cameras other than NOVUS brand it is recommended to test each time whether

required functions work correctly.

1.3. Package contents

Unpack the device carefully. After unpacking, please ensure that package contains the following items:

• Network Video Recorder

• USB Mouse

• Remote control

• User’s manual (short)

If any of the elements has been damaged during transport, pack all the elements back into the original

packaging and contact your supplier.

NVR-6332-H8/FR User’s manual (Short) ver.1.2

5

STARTING THE DEVICE

2. STARTING THE DEVICE

2.1 Electrical connection and other back panel elements.

NVR-6332-H8/FR

1. LAN1: RJ-45 connector port to connect to the local network and internet.

2. LAN2: RJ-45 connector port to connect to the local network and internet.

3. HDMI2: SPOT monitor connector, use the HDMI cable to connect SPOT monitor

4. USB: USB port for external Flash memory and other USB devices.

5. HDMI: HDMI connector, use the HDMI cable to connect monitor

6. CONNECTORS : Block of alarm input/output connectors

7. AUDIO IN: Audio mono inputs to connect microphones*.

8. FAN : Air outlet of the power supply, do not cover

9. POWER SWITCH: Power switch

10. POWER SOCKET: To plug in the 230 V power cord.

11. E-SATA: Sockets for connecting E-SATA devices

12. AUDIO OUT : Audio output

13. USB 3.0 : USB port for external Flash memory and other USB devices.

14. VGA: VGA connector, to connect VGA monitor

* Will be available in the future.

5

4

1

14

8

9

11

10

2

3

13

6

7

12

NVR-6332-H8/FR User’s manual (Short) ver.1.2

6

STARTING THE DEVICE

2.2 HDD mounting

Novus NVR-6332-H8/FR supports up to 8 internal SATA HDDs.

WARNING!

In order to find information regarding the compatible models of HDDs and their maximum

capacities, please contact Novus distributor or check the information presented at

www.novuscctv.com. AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O. is not responsible for

any problems from using not recommended hard drives.

The list of compatible HDDs contains all the HDDs that can be used with a given DVR including

HDDs designed for office use - so called desktop disks. However, due to the fact that reliability of

the recording process and data safety are paramount factors of any CCTV system, we strongly

advise to use HDDs designed for continuous (24/7) operation.

You need to format disks if they were used in a different device. All data saved on HDD prior to

format will be lost.

HDDs Installation

To install the hard disks, unscrew 3 screws on the back of the casing and two on the each side of the

recorder casing (pointed by arrows), sliding top cover backwards and then lifting it up.

WARNING: !

Before removing cover unplug the power cord from the NVR. When NVR is turned on before

disconnecting the power cord, shut down the recorder using the NVR menu.

If you use the disk previously used in another device, it is necessary to format it before using.

Formatting the drive erase all the data from disk. All drives in the recorder should be exactly the

same type.

By default, SATA cables are packed together with DVR accessories, while HDD power cable is

connected to the DVR PSU and ready for connecting the HDD.

After removing the housing, unscrew and remove the upper and lower mounting racks for disks by

unscrewing the screws on the side of the recorder housing.

NVR-6332-H8/FR User’s manual (Short) ver.1.2

7

STARTING THE DEVICE

After screwing the disks to the rail it should be remembered that to install posts supporting the top rail.

The bottom rail is supported on two supports with a threaded hole.

When reinstalling the rails with disks, screw the posts supporting the upper rail.

After installing the upper rail, screw the rail to the posts using the screws provided.

Mounted rails with disks should be secured by screwing out screws to the side of the housing.

After connecting disks, please put the top cover onto the DVR and turn the device on in order to check

the operation of particular components and to format the HDDs.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it from a

location with lower ambient temperature is forbidden, as the condensing water vapour may cause short-

circuits and damage the device as a result.

NVR-6332-H8/FR User’s manual (Short) ver.1.2

8

STARTING THE DEVICE

2.3 Connecting the HDD to the NVR via the eSATA port

The recorders allow you to connect one external drive via the eSATA port. An external hard drive

connected via the eSATA port, like the internal HDD of the recorder, is used to record recordings.

NOTE: Before connecting or disconnecting the drive to the eSATA port, first turn off the DVR.

2.4. Connecting the power supply.

Please connect provided power cord in the rear power port of the NVR like described below.

To start the unit turn on the power switch on back panel. Initialization lasts approximately 60 seconds.

During this time executing any device functions and pressing any buttons is prohibited. To shut down

the device please use the menu.

CAUTION:

Make connection when the power is not applied and the power switch is turned off.

Do not place the power cord under the carpet or rug. The power cord is usually earth-grounded.

However, even if it's not earth-grounded, never modify it on your own for earth-grounding.

Make sure that power adapter is placed near of NVR and secured from accidental disconnection.

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

NVR-6332-H8/FR User’s manual (Short) ver.1.2

9

2.5. Connecting monitor

This product supports following interfaces for main monitor: HDMI, VGA.

For HDMI following resolutions are supported: 1280x1024, 1920x1080 i 3840x2160.

2.6. Connecting camera and Network

The NVR-6332-H8/FR has two Ethernet ports for connecting the DVR in two modes. The first mode

in the recorder menu called MULTIPLE ADDRESS SETTINGS allows you to connect NVRs to

networks with different IP addresses. This mode allow to separate network with network cameras

from NVR access network. The second mode, called NETORK FAULT TOLERNANCE allows one

of network sockets of the recorder to be used as an active fault tolerant connection in case if the main

of main connections fails.

The permissible cable distance from the switch to each camera is 100m. Cameras, Internet and other

devices should be connected as shown below.

We recommend that you configure the camera before connecting to a recorder, as described in the

user manual of the camera. Please note that cameras have addressed the unique IP address supported

by the recorder. .

Connecting cameras and network recorder NVR-6332-H8/FR in MULTIPLE ADDRESS

SETTING

STARTING THE DEVICE

NOVUS NVR

INTERNET

PC

COMPUTER

IP CAMERAS

1-32

NETWORK SWITCH ROUTER

NVR-6332-H8/FR User’s manual (Short) ver.1.2

10

Connecting NVR-6332-H8/FR and cameras in NETWORK FAULT TOLERNACE mode.

Note: In order to ensure stability and protection against overload and unauthorized access, we

recommend separating the network monitoring of LANs used by users.

Before configuring the connection of the cameras in the recorder, we recommend using a PC to

configure the cameras according to the instructions of the camera.

2.7. Connecting external devices

• Connecting audio ports

Audio output signal normally are above 200mV @1kΩ load. You can connect to it the audio amplifier

with the external speakers.

• Connecting USB devices

NVR has 1 x USB 2.0 port on front and one 1 x USB 2.0 and 1 x 3.0 USB port on back panel . They

could be used for connecting external Flash memory, mouse connection and other USB compatible

devices. To connect storage memory it is recommended to use port USB 3.0

STARTING THE DEVICE

NOVUS NVR

INTERNET

PC

COMPUTER

IP CAMERAS 1-32

NETWORK SWITCH

ROUTER

BACKUP CONNECTIONS

NVR-6332-H8/FR User’s manual (Short) ver.1.2

11

• Connecting alarms ports

Example of connecting alarm output no. 1, follow the drawing below:

Example of sensor connection to alarm input 1.

STARTING THE DEVICE

NO COM

ALARM

Power

source

NO1 COM1

ALARM

Power

source

GND

Alarm in

Alarm out

RS485

NVR-6332-H8/FR User’s manual (Short) ver.1.2

12

NVR OPERATING

3. NVR OPERATING

3.1. Front panel description

1. LED LEDs for monitoring NVR activity.

- REC - monitors recording activity

- NET - monitors networking activity

- PWR - activities when power is on

2. USB PORT USB 2.0 port for external Flash memory and mouse connection.

.

3.2. Controlling via USB mouse

It is possible to control NVR via an USB mouse connected to the USB port. Double-click on any

camera in split screen display mode switches the display to full-screen mode. Subsequent double-click

returns to previous display mode. Move cursor to the top or click the right key of mouse to bring up

MAIN MENU and select START icon.

Certain positions allow to select them via mouse scroll. Depending on NVR operating mode, pressing

RMB displays a corresponding function menu.

3.3. System menu operations

To start NVR plug power cable and switch on power. The power led turns on. After booting, the video

output default is multi-window output mode.

Note:

If the currently selected NVR menu language is not as expected, to change it, please follow the

procedure described in chapter 4.3 of this manual.

1

2

NVR-6332-H8/FR User’s manual (Short) ver.1.2

13

To unlock the DVR menu, click the button at the bottom left of the screen.

After clicking on button click-on “LOGIN”

Then login in entering password in PASSWORD field (default password for user root is pass)

and then click-in LOGIN button

NVR OPERATING

NVR-6332-H8/FR User’s manual (Short) ver.1.2

14

3.4. Startup configuration

Prior to using NVR for the first time, initial setup is strongly advised. Before you connect the IP

cameras to the NVR, please set up network and stream parameters of IP cameras in the right way.

Note:

For suggested values for IP camera setting please refer to the “Cameras Capability Table” available

on the www.novuscctv.com website. If you set wrong values some problems may appear: the NVR

cannot search the IP camera, the stream cannot be connected, the image is not fluent, the image quality

is bad and so on.

In case of first NVR start WIZARD SETUP menu window will occur (if function wasn’t disabled

earlier). To configure NVR please follow procedure like below, after finishing all the steps you’ll be

ready to work:

Provide username and password and click on NEXT button so start wizard.

NVR OPERATING

NVR-6332-H8/FR User’s manual (Short) ver.1.2

15

I. NETWORK SETTINGS : This menu allows to set up networking. To select desired mode clik-on

WORK PATTERN field. MULTIPLE ADDRESS SETTING mode allows to use address Ethernet

Interfaces in separated IP subnets. NETWORK FAULT TOLERANCE uses one of Ethernet interface

as an fault tolerant connection activated after main connection break down. Default IP configuration is

192.168.1.100 netmask 255.255.255.0. It is possible to configure IP address for switch in INTERNAL

ETHERNET PORT SECTION. Please note that IP subnet for the ETHERNET PORT 1 and

INTERNAL ETHERNET PORT were different. In cases where it is necessary to connect NVR to the

Internet (for remote access, email sending, etc.), configure the following parameters: Gateway,

Primary and Secondary DNS. You can also enable DHCP mode which allows you to download an IP

address from a DHCP server (required if running a DHCP server). It is possible to change the default

HTTP port designed to display Web panel of the device and RTSP ports and port server data. After

changing parameter pres NEXT button.

NVR OPERATING

Internal PoE Ports

IP address settings

Internal PoE Ports

IP address settings

Work pattern selction

NVR-6332-H8/FR User’s manual (Short) ver.1.2

16

II. QR CODES : This menu allows you to scan a QRcode in the Supelive plus application or enter a

device code to autonat.com site. The service allows you to connect to a device connected to the Internet

network behind a router equipped with NAT.

NOTE: SYSTEMY BEZPIECZEŃSTWA SP. Z O.O. is not responsible for the operation of the service

autonat.com which is provided by third parties.

III. Add Camera: Allows you to configure the camera and add them to the recorder. Upper window

displays cameras discovered by the NVR. To change the addressable cameras, click on the icon in

the column EDIT (This works with cameras NOVUS IP 3000 series).

NVR OPERATING

NVR-6332-H8/FR User’s manual (Short) ver.1.2

17

Enter the address in the IP ADDRESS field and set the masks in the SUBNET MASK, then press the

OK button to save the settings.

Press the button to add a camera to the system.

Added camera will be displayed on the bottom of the menu list. To edit the connection settings of the

camera, press the EDIT column.

If you are having problems connecting to the camera, you must enter the correct user name in the

USER NAME and password in the PASSWORD field and then press the OK button to save the

settings. If the NVR connected to the camera in STATUS filed will be displayed “Connected”. To

remove a camera from the list, press the in DELETE column.

NVR OPERATING

NVR-6332-H8/FR User’s manual (Short) ver.1.2

18

IV.DISK SETTINGS : In this tab information about the hard disk detected by the DVR is displayed.

Before starting work, you need to format the hard disk by selecting it in the list of drives and then

pressing FORMAT.

Formatting may take a few moments. After properly formatted STATUS field should have a value of

„RW” (Read/Write).

V. Record Settings :

You can set one of the modes:

- MANUAL RECORD SETTINGS - You can set the recording time from the moment you select the

manual recording in range from 1 minute to 1 hour or manually off recording.

NVR OPERATING

NVR-6332-H8/FR User’s manual (Short) ver.1.2

19

AUTO - set all the cameras on one of the following modes :

- MOTION RECORD - starts recording after receiving motion detection information from the camera.

- SENSOR RECORD - starts recording after alarm generated on alarm input

- MOTION RECORD + SENSOR RECORD - starts recording after motion detecion alarm and after

alarm from alarm inputs

- ALWAYS(24x7) RECORD + MOTION RECORD - continuous recording and recording after

receiving motion detection information from the camera.

- ALWAYS(24x7) RECORD + SENSOR RECORD - continuous recording and recording alarm

generated on alarm input

- ALWAYS(24x7) RECORD + MOTION RECORD + SENSOR RECORD - continuous recording

and recording alarm generated on alarm input and after receiving motion detection information from

the camera.

- ALWAYS(24x7) RECORD + MOTION RECORD + SENSOR RECORD + INTELIGENCE

RECORD - continuous recording and recording alarm generated on alarm input, motion detection

information and after receiving Intelligence Analysis from the camera.

NVR OPERATING

NVR-6332-H8/FR User’s manual (Short) ver.1.2

20

4. NVR MENU

4.1. Live monitoring

NOVUS network video recorders features a multilingual OSD menu allowing to adjust the settings of

the device. Available languages are: English, Polish, and others

As soon as the NVR completes its initialization process, it will enter the real-time monitoring image.

Displaying all cameras simultaneously is the default mode. On the bottom of screen STATUS BAR is

displayed.

To start access to the NVR click on the button to launch the start menu.

After clicking log on to the system (the default password for the root user is a pass).

STATUS BAR description:

NVR MENU

MENU BAR

VIDEO WINDOW

VIEW MENU

START MENU

Item Icon Description

Search Launches search for recordings

Playback

Starts playback menu

Backup

Starts backup menu

Strona jest ładowana ...

AAT NVR-6332-H8/FR Instrukcja obsługi

AAT NVR-6332-H8/FR Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty