Novus NVR-6408-H1/F Instrukcja obsługi

User’ s ma n ual

(shor t )

NVR-6408-H1/F

NVR-6408-H1/F User’s manual (Short) version 1.2

2

IMPORTANT SAFEGUARDS AND WARNINGS

THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING DIRECTIVES:

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for

self installation in households by individuals without technical knowledge. The manufacturer is not

responsible for defects and damages resulted from improper or inconsistent with user’s manual

installation of the device in the system.

ATTENTION!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT PROVISIONED FOR THE GIVEN

PRODUCT IN ITS USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE

PRODUCT, OR THAT ARISES FROM THE NORMAL APPLICATION OF THE PRODUCT, ITS

MANUFACTURER MUST BE CONTACTED OR THE RESPONSIBILITY OF THE MANUFACTURER

FOR THE RESULTS OF SUCH AN ACTION SHELL BE EXCLUDED.

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is

necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct influence

on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is forbidden;

7. You are not allowed to use the device in high humidity environment (i.e. close to swimming pools, bath tubs,

damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

9. Mounting the device on unstable surface or using not recommended mounts is forbidden. Improperly mounted

device may cause a fatal accident or may be seriously damaged itself. The device must be mounted by qualified

personnel with proper authorization, in accordance with this user’s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with those specified

by the producer in the devices technical datasheet. Therefore, it is forbidden to supply the devices from a power

sources with unknown parameters, unstable or not meeting producer’s requirements;

11. You cannot allow any metal objects get inside the recorder. It might cause serious damage. If a metal object

gets inside the device contact the authorised Novus service immediately.

12. The manufacturer does not bear responsibility for damage or loss of data stored on HDDs or other media

occurred during the usage of the product.

Due to the product being constantly enhanced and optimized, certain parameters and functions described in the

manual in question may change without further notice.

We strongly suggest visiting the www.novuscctv.com website in order to access the newest manual .

Technical changes reserved without prior notice and printing errors possible.

DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIMENT

AND OF THE COUNCIL of 26 February 2014 on the harmonisation

of the laws of the Member States relating to electromagnetic compatibility

(OJ L 96, 29.3.2014, p. 79–106, with changes)

DIRECTIVE 2014/35/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 26 February 2014 on the harmonization

of the laws of the Member States relating to the making available on the market of electrical

equipment designed for use within certain voltage limits.

DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 4 July 2012 on waste electrical and electronic equipment

(WEEE) (OJ L 197, 24.7.2012, p. 38–71,with changes)

DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 8 June 2011 on the restriction of the use

of certain hazardous substances in electrical and electronic equipment

(OJ L 174, 1.7.2011, p. 88–110, with changes)

NVR-6408-H1/F User’s manual (Short) version 1.2

3

FOREWORD INFORMATION

1. FOREWORD INFORMATION

1.1. Network recorder’s technical data

VIDEO

IP Cameras 8 channels at 2592 x 1944 resoluon (video + audio)

Supported Resoluon max. 3840 x 2160

Compression H.264, H.264+, H.265

Monitor Output

main (split screen, full screen, sequence): 1 x VGA, 1 x HDMI (4K UltraHD)

(up to 2 monitors simultaneously

Dualstreaming Support yes

AUDIO

Audio Output 1 x HDMI

RECORDING

Recording Speed 240 kl/s (8 x 30 kl/s for 3840 x 2160)

Stream Size 80 Mb/s in total from all cameras

Recording Mode

me-lapse, triggered by: manual, alarm input, moon detecon, intelligent image analysis func-

ons

Prealarm/Postalarm up to 5 s/up to 600 s

DISPLAY

Display Speed 240 fps (8 x 30 fps)

PLAYBACK

Playback Speed 240 fps (8 x 30 fps for 3840 x 2160)

Recorded Data Search by date/me, events, moon in a dened area, related to face recognion

BACKUP

Backup Methods USB port (HDD or Flash memory), network

Backup File Format AVI

STORAGE

Internal storage available mount: 1 x HDD 3.5” 8 TB SATA

Total Internal Capacity 8 TB

ALARM

Camera Alarm Input/Output supports camera’s alarm input/output

Moon Detecon supports camera’s moon detecon

System Reacon to Alarm Events buzzer, alarm output acvaon, recording acvaon, PTZ, e-mail with atatchment

INTELLIGENT IMAGE ANALYSIS

Supported funcons

Excepon, Scene Change, Video Blurred, Video Color Cast, Tripwire,

Zone entrance, Abandoned Object, Object Disappearance, Face Detecon

NETWORK

Network Interface 1 x Ethernet - RJ-45 interface, 10/100/1000 Mbit/s

Network Protocols Support HTTP, TCP/IP, IPv4, FTP, DHCP, DNS, DDNS, NTP, RTSP, UPnP, SNMP, SMTP

ONVIF Protocol Support Prole S (ONVIF 2.2 or higher)

Smartphone Soware SuperLive Plus (iPhone, Android)

Max. Number of Connecons with NVR 2

Bandwidth 80 Mb/s in total to all client workstaons

PTZ

PTZ Funcons pan/lt/zoom, preset commands

AUXILIARY INTERFACES

USB Ports 1 x USB 2.0, 1 x USB 3.0

OPERATING SYSTEM

Operang System Linux

Operaon Mode triplex

OSD languages: Polish, English, others

Control PC mouse (in-set included), network

System Diagnosc automac control of: HDDs, network, camera connecon loss

Security password protecon, IP ltering, MAC ltering

INSTALLATION PARAMETERS

Dimensions (mm) 300 (W) x 44 (H) x 248 (D)

Weight 0.65 kg (without HDD)

Power Supply 12 VDC (100 ~ 240 VAC/12 VDC PSU in-set included)

Power Consumpon 18 W (with 1 HDD)

Operang Temperature -10°C ~ 50°C

NVR-6408-H1/F User’s manual (Short) version 1.2

4

FOREWORD INFORMATION

1.2. Main characteristics

• Supports resolution up to 3840 x 2160

• Supported protocols: ONVIF

• Recording up to 3840 x 2160

• Recorded stream size up to 80 Mb/s in total from all cameras

• Internal HDDs mount up to 1

WARNING!

ONVIF protocol support was verified with IP cameras based on ONVIF ver. 2.2 and compatible

with the "PROFILE S".

Implementation of the ONVIF protocol by different manufacturers may vary by some functions,

which can make them work improperly or not in accordance with expectation. AAT SYSTEMY

BBEZPIECZEŃSTWA SP. Z O.O. company is not responsible for incompatibility problems

resulting from cameras of other brands than NOVUS, which are using ONVIF protocol. If you

are using ONVIF protocol cameras other than NOVUS brand it is recommended to test each

time whether required functions work correctly.

1.3. Package contents

Unpack the device carefully. After unpacking, please ensure that package contains the following items:

• Network Video Recorder

• USB Mouse

• Power supply

• User’s manual (short)

If any of the elements has been damaged during transport, pack all the elements back into the original

packaging and contact your supplier.

NVR-6408-H1/F User’s manual (Short) version 1.2

5

STARTING THE DEVICE

2. STARTING THE DEVICE

2.1 Electrical connection and other back panel elements.

NVR-6408-H1/F

1. TERMINAL: Input/output alarm terminal

2. .AUDIO IN: Audio mono inputs to connect microphones*.

3. VGA: Main monitor connectors, use the D-SUB VGA cable to connect monitor.

4. HDMI: Main monitor connectors, use the HDMI cable to connect monitor.

5. USB: USB port for external Flash memory and other USB devices.

6. LAN: RJ-45 connector port to connect to the local network and internet.

7. POWER SOCKET: To plug in the 12V power cord

8. AUDIO OUT : Audio output

6

5

4

3

2

1

8

7

NVR-6408-H1/F User’s manual (Short) version 1.2

6

STARTING THE DEVICE

2.2 HDD mounting

Novus NVR-6408-H1/F support 1 internal SATA HDD.

WARNING!

In order to find information regarding the compatible models of HDDs and their maximum

capacities, please contact Novus distributor or check the information presented at

www.novuscctv.com. AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O. company is not

responsible for any problems from using not recommended hard drives.

The list of compatible HDDs contains all the HDDs that can be used with a given DVR including

HDDs designed for office use - so called desktop disks. However, due to the fact that reliability of

the recording process and data safety are paramount factors of any CCTV system, we strongly

advise to use HDDs designed for continuous (24/7) operation.

You need to format disks if they were used in a different device. All data saved on HDD prior to

format will be lost.

HDD Installation

In order to mount HDD, please loose the screws in the locations shown on the picture below and

remove the cover.

WARNING: !

Before removing cover unplug the power cord from the NVR. When NVR is turned on before

disconnecting the power cord, shut down the recorder using the NVR menu.

NVR-6408-H1/F User’s manual (Short) version 1.2

7

STARTING THE DEVICE

After enclosure, mount the disk using mounting screws (4 pcs.), And then connect the power cord and

signal.

After connecting the hard drive mount the cover start the NVR to check and format the hard drive.

CAUTION:

If you use the disk was used in another device, it is necessary to format it before using.

Formatting the drive erase all the data from disk. All drives in the recorder should be exactly the

same type.

2.3. Connecting the power supply.

Please connect provided power cord in the rear power port of the NVR like depicted below.

Initialization lasts approximately 60 seconds. During this time executing any device functions and

pressing any buttons is prohibited. To shut down the device please use the menu.

CAUTION:

Make connection when the power is not applied and the power switch is turned off.

Do not place the power cord under the carpet or rug. The power cord is usually earth-grounded.

However, even if it's not earth-grounded, never modify it on your own for earth-grounding.

Make sure that power adapter is placed near of NVR and secured from accidental disconnection.

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

NVR-6408-H1/F User’s manual (Short) version 1.2

8

2.4. Connecting monitor

This product supports following interfaces for main monitor: HDMI, VGA.

For HDMI following resolutions are supported: 1280x1024, 1920x1080 i 3840x2160.

2.5. Connecting camera and Network

NVR-6408-H1/F need external network switch for connecting cameras. Please notice that the

Ethernet connection is effective within 100 meter distance. To connect IP cameras please connect

cables like on image and follow the described below.

We recommend that you configure the camera before connecting to a recorder, as described the

manual camera. Please note that cameras have addressed the unique IP address supported by the

recorder.

Connecting cameras and network recorders NVR-6408-H1/F

2.6. Connecting external devices

• Connecting audio ports

Audio output signal normally are above 200mV 1kΩ. You can connect to it the audio amplifier with

the external speakers.

• Connecting USB devices

NVR has 1 x USB 2.0 port on front and one 1 x USB 2.0 on back. They could be used for connecting

external Flash memory, mouse connection and other USB compatible devices. To connect storage

memory it is recommended to use port USB 3.0

STARTING THE DEVICE

NETWORK SWITCH

INTERNET

PC

NOVUS NVR

IP CAMERAS

NVR-6408-H1/F User’s manual (Short) version 1.2

9

• Connecting alarms ports

NVR-6408-H1/F has local alarm input and output. To connect alarm input please refer image below

An example of connecting the sensor to the alarm input 1.

STARTING THE DEVICE

NO COM

ALARM

Power

source

ALARM

IN1 IN2 IN3 IN4

GND SENSOR

NVR-6408-H1/F User’s manual (Short) version 1.2

10

NVR OPERATING

3. NVR OPERATING

3.1. Front panel description

1. LED Diodes for monitoring NVR activity.

- REC - monitors recording activity

- NET - monitors networking activity

- PWR - activities when power is on

2. USB USB 2.0 port for external Flash memory and mouse connection.

.

3.2. Controlling via USB mouse

It is possible to control NVR via an USB mouse connected to the USB port. Double-click on any

camera in split screen display mode switches the display to full-screen mode. Subsequent double-click

returns to previous display mode. Move cursor to the top or click the right key of mouse to bring up

MAIN MENU and select START icon.

Certain positions allow to select them via mouse scroll. Depending on NVR operating mode, pressing

RMB displays a corresponding function menu.

3.3. System operations

To start NVR plug power cable. The power led turns on. After booting, the video output default is multi

-window output mode.

Note:

If the currently selected NVR menu language is not as expected, to change it, please follow the

procedure described in chapter 4.3 of this manual.

1

2

NVR-6408-H1/F User’s manual (Short) version 1.2

11

To unlock the DVR menu, press the button at the bottom left of the screen.

After clicking on button click-on “LOGIN”

Then login in entering password in PASSWORD field (default password for user root is “pass”)

and then click-in login button

NVR OPERATING

NVR-6408-H1/F User’s manual (Short) version 1.2

12

3.4. Startup configuration

Prior to using NVR for the first time, initial setup is strongly advised. Before you connect the IP

cameras to the NVR, please set up network and stream parameters of IP cameras in the right way.

Note:

For suggested values for IP camera setting please refer to the “Cameras Capability Table” available

on the www.novuscctv.com website. If you set wrong values some problems may appear: the NVR

cannot search the IP camera, the stream cannot be connected, the image is not fluent, the image quality

is bad and so on.

In case of first NVR start WIZARD SETUP menu window will occur (if function wasn’t disabled

earlier). To configure NVR please follow procedure like below, after finishing all the steps you’ll be

ready to work:

Provide username and password and click on NEXT button so start wizard.

NVR OPERATING

NVR-6408-H1/F User’s manual (Short) version 1.2

13

I. Network Settings : This menu allows to set up networking. Default IP configuration is

192.168.1.100 netmask 255.255.255.0. Configure the following parameters: Gateway, Primary and

Secondary DNS. You can also enable DHCP mode allows you to download an IP address from a

DHCP server (required if running a DHCP server). It is possible to change the default HTTP port

designed to display panel Web device and RTSP ports and port server data. After changing parameter

pres NEXT button.

NVR OPERATING

NVR-6408-H1/F User’s manual (Short) version 1.2

14

II. Add Camera: Allows you to configure the camera and add them to the recorder. Upper window

displays a sophisticated camera by the NVR. To change the addressable cameras, click on the icon

in the column EDIT (This works with cameras NOVUS IP 3000 series).

Enter the address in the IP ADDRESS and set the masks in the SUBNET MASK then press the OK

button to save the settings.

Press the button to add a camera to the system.

Added camera will be displayed on the bottom of the menu list. To edit the connection settings of the

camera, press the EDIT column.

NVR OPERATING

NVR-6408-H1/F User’s manual (Short) version 1.2

15

If you are having problems connecting to the camera, you must enter the correct user name in the

USER NAME and password in the PASSWORD field and then press the OK button to save the

settings. If the NVR connected to the camera will be on STATUS will be displayed Connected. To

remove a camera from the list, press the in DELETE column.

III. Disk Settings :

In this tab displays information about the hard disk detected by the DVR.

Before starting work, you need to format the hard disk by selecting it in the list of drives and then

pressing FORMAT.

Formatting may take a few moments. After properly formatted STATUS field should have a value of

„RW” (Read/Write).

NVR OPERATING

NVR-6408-H1/F User’s manual (Short) version 1.2

16

IV. Record Settings :

You can set one of the modes:

• MANUAL RECORD SETTINGS - You can set the recording time from the moment you select

the manual recording from 1 minute to 1 hour or manually off recording.

• AUTO - set all the cameras on one of the following modes :

- MOTION RECORD - starts recording after receiving motion detection information from the camera.

- SENSOR RECORD - starts recording after alarm generated on alarm input

- MOTION RECORD + SENSOR RECORD - starts recording after motion detecion alarm and after

alarm from alarm inputs

- ALWAYS(24x) RECORD +MOTION RECORD - constant recording and recoring after receiving

motion detection information from the camera.

- ALWAYS(24x) RECORD + SENSOR RECORD - constant recording and recording alarm generated

on alarm input

- ALWAYS(24x) RECORD + MOTION RECORD + SENSOR RECORD - constant recording and

recording alarm generated on alarm input and after receiving motion detection information from the

camera.

Double-clicking on the selected mode, set the parameter editing of the recorded stream for the selected

mode. This enables eg. Recording stream of lower quality for continuous recording and higher quality

when motion is detected.

NVR OPERATING

NVR-6408-H1/F User’s manual (Short) version 1.2

17

V. QR Codes : This menu allows to you to scan a QRcode in the Supelive plus application or enter a

device code to autonat.com site. The service allows you to connect to a device connected to the Internet

network is behind a router equipped with NAT. Check the NAT checkbox to enable P2P service.

NOTE: AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O. is not responsible for the operation of the

service autonat.com which is provided by third parties.

NVR OPERATING

NVR-6408-H1/F User’s manual (Short) version 1.2

18

4. NVR MENU

4.1. Live monitoring

NOVUS network video recorders features a multilingual OSD menu allowing to adjust the settings of

the device. Available languages are: English, Polish, and others

As soon as the NVR completes its initialization process, it will enter the real-time monitoring image.

Displaying all cameras simultaneously is the default mode. On the bottom of screen STATUS BAR is

displayed.

To start access to the NVR click on the button to launch the start menu.

After clicking log on to the system (the default password for the root user is a "pass").

.

STATUS BAR description:

NVR MENU

Item Icon Description

Search Launches search for recordings

Playback

Starts playback menu

Backup

Starts backup menu

MENU BAR

VIDEO WINDOW

VIEW MENU

START MENU

NVR-6408-H1/F User’s manual (Short) version 1.2

19

Menu bar icons

NVR MENU

Item Icon Description

Settings Click to run conguration of NVR parameters

Logout

Starts playback menu

Shutdown

Starts backup menu

Item Icon Description

Settings Click to open start menu

Full screen

Switches video view to full screen

Single view Start displaying camera in single view

Quad view

Start displaying 4 cameras in video view

9 cam. View Start displaying 9 cameras in video view

Other divisions

Opening video subdivisions

Other divisions

Open 1 main + 5 or 7 additional views

Dwell

Starts displaying images in sequence

Dwell settings

Start/Stop time setting switch

NVR-6408-H1/F User’s manual (Short) version 1.2

20

View menu

Detailed information about configuration, service and installation of device is

available in full version of user's manual located on the www.novuscctv.com

NVR MENU

Item

Icon Description

OSD ON/OSD OFF

Turns on/off OSD information

Playback

Starts playback for displayed cameras

Manual Record

Turn on / off manually recording channels.

Manual Alarm

Allow to trigger the alarm manually.

Recording Status

Displays information about the recording

Alarm Status

Displays the status of alarm devices

Disc Status

Information about disc status

Network status

View information about network usage

Device Information

Displays information about the state of operation of the

basic components of recorder

Item Icon Description

Camera List of cameras to display

Single Channel

Sequences

Select a group of cameras to display in single chan-

nel

Customize Displays

Modes

Customize display and save settings

Strona jest ładowana ...

Novus NVR-6408-H1/F Instrukcja obsługi

Novus NVR-6408-H1/F Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty