Novus NVR-6316-H2-II Instrukcja obsługi

User’ s ma n ual

(shor t )

NVR-6316-H2-II

User’s manual (Short) ver.1.0

2

IMPORTANT SAFEGUARDS AND WARNINGS

THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING DIRECTIVES:

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self installation in households by

individuals without technical knowledge. The manufacturer is not responsible for defects and damages resulted from improper or

inconsistent with user’s manual installation of the device in the system.

ATTENTION!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT PROVISIONED FOR THE GIVEN PRODUCT IN ITS USER’S MANUAL AND OTHER DOCUMENTS

DELIVERED WITH THE PRODUCT, OR THAT ARISES FROM THE NORMAL APPLICATION OF THE PRODUCT, ITS MANUFACTURER MUST BE CONTACTED

OR THE RESPONSIBILITY OF THE MANUFACTURER FOR THE RESULTS OF SUCH AN ACTION SHELL BE EXCLUDED.

1. Prior to undertaking any action please consult the following manual and read all the safety and operating instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct influence on user’s safety and durability and

reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is forbidden;

7. You are not allowed to use the device in high humidity environment (i.e. close to swimming pools, bath tubs, damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not recommended since it may lead to heat

build-up and damaging the device itself as a consequence;

9. Mounting the device on unstable surface or using not recommended mounts is forbidden. Improperly mounted device may cause a fatal accident or

may be seriously damaged itself. The device must be mounted by qualied personnel with proper authorization, in accordance with this user’s

manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with those specied by the producer in the devices

technical datasheet. Therefore, it is forbidden to supply the devices from a power sources with unknown parameters, unstable or not meeting

producer’s requirements;

11. You cannot allow any metal objects get inside the recorder. It might cause serious damage. If a metal object gets inside the device contact the

authorised Novus service immediately.

12. The manufacturer does not bear responsibility for damage or loss of data stored on HDDs or other media occurred during the usage of the product.

Due to the product being constantly enhanced and optimized, certain parameters and functions described in the manual in question may change

without further notice.

We strongly suggest visiting the www.novuscctv.com website in order to access the newest manual .

Technical changes reserved without prior notice and printing errors possible.

DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIMENT

AND OF THE COUNCIL of 26 February 2014 on the harmonisation

of the laws of the Member States relating to electromagnetic compatibility

(OJ L 96, 29.3.2014, p. 79–106, with changes)

DIRECTIVE 2014/35/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 26 February 2014 on the harmonization

of the laws of the Member States relating to the making available on the market of electrical

equipment designed for use within certain voltage limits.

DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 4 July 2012 on waste electrical and electronic equipment

(WEEE) (OJ L 197, 24.7.2012, p. 38–71,with changes)

DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 8 June 2011 on the restriction of the use

of certain hazardous substances in electrical and electronic equipment

(OJ L 174, 1.7.2011, p. 88–110, with changes)

NVR-6316-H2-II

User’s manual (Short) ver.1.0

3

FOREWORD INFORMATION

1. FOREWORD INFORMATION

1.1. Network recorder’s technical data

NVR-6316-H2-II

Video

IP Cameras Displaying 16 channels at 3840 x 2160 resolution using H.264 codec (video + audio)

Maximum Supported Camera Resolution 3840 x 2160

Compression H.264, H.264+, H.265

Monitor Output

main (split screen, full screen, sequence): 1 x HDMI, 1 x VGA (up to 1 moni-

tor simultaneously)

Dualstreaming Support yes

Audio

Audio Output 1 x line-out (RCA) 1 x HDMI

Recording

Recording Speed 480 fps (16 x 30 fps for 3840 x 2160 and lower)

Stream Size 112 Mb/s in total from all cameras

Recording Mode time-lapse, triggered by: manual, motion detection

Prealarm/Postalarm up to 5 s/up to 600 s

Display

Display Speed 480 fps (16 x 30 fps)

Playback

Playback Speed 480 fps (16 x 30 fps for 3840 x 2160)

Recorded Data Search by date/time, events

Backup

Backup Methods USB port (HDD or Flash memory), network

Storage

Internal Storage available mount: 2 x HDD 3.5” 8 TB SATA

Total Internal Capacity 16 TB

Alarm

Camera Alarm Input/Output supports camera’s alarm input/output

Motion Detection supports camera’s motion detection

System Reaction to Alarm Events buzzer, recording activation, PTZ, e-mail with atatchment

Intelligent image analysis

Supported Functions

Exception, Scene Change, Video Blurred, Video Color Cast, Tripwire, Zone

entrance, Abandoned Object, Object Disappearance

Network

Network Interface 1 x Ethernet - RJ-45 interface, 10/100/1000 Mbit/s

Network Protocols Support

HTTP, TCP/IP, IPv4, HTTPS, FTP, DHCP, DNS, DDNS, NTP, RTSP,

UPnP, SNMP, SMTP

ONVIF Protocol Support Profile S (ONVIF 2.2 or higher)

PC/MAC Software NMS, Internet Explorer, NVR-6000 Viewer/-

Mobile applications SuperLive Plus (iPhone, Android)

Number of Simultaneous Connections

up to 5 clients, up to 22 main streams or 64 substreams or 16 playback stre-

ams in total

Bandwidth 112 Mb/s in total to all client workstations

PTZ

PTZ Functions pan/tilt/zoom, preset commands

Auxiliary Interfaces

USB Ports 2 x USB 2.0,

Operating system

Operating System Linux

Operation Mode triplex

OSD languages: Polish, English, others

Control PC mouse and IR remote controller (in-set included), network

System Diagnostic automatic control of: HDDs, network, camera connection loss

Security password protection, IP filtering, MAC filtering

Installation parameters

Dimensions (mm) 380 (W) x 52 (H) x 268 (D)

Weight 1.52 kg (without HDD)

Power Supply 12 VDC (100 ~ 240 VAC/12 VDC PSU in-set included)

Power Consumption 30 W (with 2 HDDs)

Operating Temperature -10°C ~ 50°C

NVR-6316-H2-II

User’s manual (Short) ver.1.0

4

FOREWORD INFORMATION

1.2. Main characteristics

• Supports resolution up to 3840 x 2160

• Supported protocols: ONVIF

• Recording up to 3840 x 2160

• Recorded stream size up to 112 Mb / s in total from all cameras

• Internal HDD mount up to 2

WARNING!

ONVIF protocol support was verified with IP cameras based on ONVIF ver. 2.2 and compatible

with the "PROFILE S".

Implementation of the ONVIF protocol by different manufacturers may vary by some functions,

which can make them work improperly or not in accordance with expectation. AAT SYSTEMY

BEZPIECZEŃSTWA sp. z o.o. Company is not responsible for incompatibility problems

resulting from cameras of other brands than NOVUS, which are using ONVIF protocol. If you

are using ONVIF protocol cameras other than NOVUS brand it is recommended to test each

time whether required functions work correctly.

1.3. Package contents

Unpack the device carefully. After unpacking, please ensure that package contains the following items:

• Network Video Recorder

• USB Mouse

• Remote control

• Power supply

• User’s manual (short)

If any of the elements has been damaged during transport, pack all the elements back into the original

packaging and contact your supplier.

NVR-6316-H2-II

User’s manual (Short) ver.1.0

5

STARTING THE DEVICE

2. STARTING THE DEVICE

2.1 Electrical connection and other back panel elements.

NVR-6316-H2-II

1. VGA: Main monitor connector, use the D-SUB VGA cable to connect monitor.

2. HDMI: Main monitor connector, use the HDMI cable to connect monitor.

3. LAN: RJ-45 connector port to connect to the local network and internet.

4. USB: USB port for external Flash memory and other USB devices.

5. CONNECTORS: Block of alarm input/output connectors

6. AUDIO IN: Audio mono inputs to connect microphones

7. POWER SOCKET: To plug in the 12 V power cord

8. AUDIO OUT: Audio output

5

4

3

2

1

8

6

7

NVR-6316-H2-II

User’s manual (Short) ver.1.0

6

STARTING THE DEVICE

2.2 HDD mounting

Novus NVR-6316-H2-II supports 2 internal SATA HDDs

WARNING!

In order to find information regarding the compatible models of HDDs and their maximum

capacities, please contact Novus distributor or check the information presented at

www.novuscctv.com. AAT SYSTEMY BEZPIECZEŃSTWA sp. z o.o. Company is not

responsible for any problems from using not recommended hard drives.

The list of compatible HDDs contains all the HDDs that can be used with a given DVR including

HDDs designed for office use - so called desktop disks. However, due to the fact that reliability of

the recording process and data safety are paramount factors of any CCTV system, we strongly

advise to use HDDs designed for continuous (24/7) operation.

You need to format disks if they were used in a different device. All data saved on HDD prior to

format will be lost.

WARNING: !

Before removing cover unplug the power cord from the NVR. When NVR is turned on before

disconnecting the power cord, shut down the recorder using the NVR menu.

In order to mount HDD, please loose the screws in the locations shown on the picture below and

remove the cover.

NVR-6316-H2-II

User’s manual (Short) ver.1.0

7

STARTING THE DEVICE

After enclosure, mount the disk using mounting screws (4 pcs.), And then connect the power cord and

signal.The recorder casing has 6 holes enabling adaptation to hard disk mounting holes.

After connecting the hard drive mount the cover start the NVR to check and format the hard drive.

WARNING:

If the disk used has been used in another device, it must be formatted. The formatting process

results in the loss of data saved on the disk.

2.3. Connecting the power supply.

To start please connect provided power cord in the rear power port of the NVR like depicted below.

Initialization lasts approximately 60 seconds. During this time executing any device functions and

pressing any buttons is prohibited. To shut down the device please use the menu.

CAUTION:

Make connection when the power is not applied.

Do not place the power cord under the carpet or rug. The power cord is usually earth-grounded.

However, even if it's not earth-grounded, never modify it on your own for earth-grounding.

Make sure that power adapter is placed near of NVR and secured from accidental disconnection.

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

NVR-6316-H2-II

User’s manual (Short) ver.1.0

8

STARTING THE DEVICE

2.4. Connecting monitor

The recorders have HDMI and VGA connectors.

Following resolutions are supported for HDMI output : 1280x1024, 1920x1080, 3840x2160

WARNING :

Emergency switching of the screen resolution is possible after pressing the right mouse button

after more than 5 seconds until you hear a sound signal from the recorder.

2.5. Connecting camera and Network

The recorder requires the use of a switch to connect cameras. The permissible cable distance from the

switch to each network device is 100m. Cameras, Internet and other devices should be connected as

shown below.We recommend configuring the cameras before connecting to the recorder as described

in the camera user's manual. Please remember that the cameras should be addressed with a unique IP

address supported by the recorder. Connecting cameras and network devices to the recorder

Before configuring the connection of cameras in the recorder, we recommend using a PC to configure

the cameras in accordance with the camera instructions.

NETWORK

SWITCH

INTERNET

PC

NOVUS NVR

IP CAMERAS

NVR-6316-H2-II

User’s manual (Short) ver.1.0

9

NVR OPERATING

2.6. Connecting external devices

• Connecting audio ports

Audio output signal normally are above 200mV 1kΩ. You can connect to it the audio amplifier with the

external speakers.

• Connecting USB devices

NVR has 1 x USB 2.0 port on front and one 1 x USB 2.0 on back. They could be used for connecting

external Flash memory, mouse connection and other USB compatible devices.

3. NVR OPERATING

3.1. Front panel description

1. LED Recorder operation LEDs.

- REC - recording started

- NET - network activity

- PWR - power supplay activity

2. USB USB 2.0 port for connecting a mouse with a USB connector or Flash

memory for copying recordings.

3.2. Controlling via USB mouse

It is possible to control NVR via an USB mouse connected to the USB port. Double-click on any

camera in split screen display mode switches the display to full-screen mode. Subsequent double-click

returns to previous display mode. Move cursor to the top or click the right key of mouse to bring up

MAIN MENU and select START icon.

Certain positions allow to select them via mouse scroll. Depending on NVR operating mode, pressing

RMB displays a corresponding function menu.

Note:

If the currently selected NVR menu language is not as expected, to change it, please follow the

procedure described in chapter 4.3 of this manual.

1

2

NVR-6316-H2-II

User’s manual (Short) ver.1.0

10

3.3. First start

After the first start of the NVR, a window is displayed that allows you to select the language used in

the menu (window on the left) and the location of the device in (window on the right). Left clicking in

one window changes the settings.

To go to the next menu, click on NEXT button.

The next wizard window allows you to set time parameters such as TIME ZONE, SYSTEM TIME,

DATE FORMAT, TIME FORMAT, DST, SYNCHRONOUS, NTP SERVER and VIDEO FORMAT.

After making your selection, click NEXT to open next page. .

NVR OPERATING

NVR-6316-H2-II

User’s manual (Short) ver.1.0

11

In the password change wizard, you must change the password. The password must be at least 8

characters long. It should contain a number, uppercase and lowercase. They must be entered on the on-

screen keyboard available after clicking on NEW PASSWORD and CONFIRM PASSWORD.

To display the entered password, check the DISPLAY PASSWORD box. Checking in the

AUTOMATICALLY LOG IN field will automatically log the user into the system after starting the

recorder. By selecting the ENABLE field in the GRAPHICAL LOCK row, you can start the user

unblocking setting by using a graphic pattern instead of entering the password. To start the graphic sign

settings, click on the EDIT button. Then, holding the left mouse button, move the cursor between the

displayed wheels and mark the pattern that will be used to unlock the device twice.

NVR OPERATING

NVR-6316-H2-II

User’s manual (Short) ver.1.0

12

After clicking the NEXT button, a window will appear that allows you to set a set of questions and

answers that can unlock access to the recorder when root password is unknow.

To add a question, click the QUESTION field to enter a question using the keyboard. Then click on

the ANSWER field to enter the answer to the question. Clicking on the ADD button adds a set of

questions and answers. Clicking the NEXT button will take you to the window in which information

about the disk connected to the recorder is displayed.

If information about the unavailability of the disk is displayed in the STATUS field, format the disk

by clicking the FORMAT button. A window will appear asking you for confirmation of disk

formating proces.

NOTE: Formatting a disk will lose information stored on the disk.

NVR OPERATING

NVR-6316-H2-II

User’s manual (Short) ver.1.0

13

Pressing the OK button confirms the intention to format the disk.

To start formatting, enter a username and password for a user with administrator rights.

After entering the username and password, press the FORMAT NOW button. After successful

formatting, the disk should have the status "READ AND WRITE".

NVR OPERATING

NVR-6316-H2-II

User’s manual (Short) ver.1.0

14

3.4. Wizzard setup

When the NVR is started for the first time, the settings wizard window is displayed. In order to

properly configure the recorder, please follow the procedure given:

Information:

Recommended setting values for cameras can be found in the "Camera compatibility table" available

at www.novuscctv.com. If you set the wrong values, you may not be able to find, connect cameras or

get a smooth image without distortion.

Before you start working with the network recorder, you should perform the initial configuration of

the device. Click the WIZARD SETUP button to start the wizard

I. By default, the recorder has the IP address and DNS settings download from the DHCP server

enabled. If the address retrieval fails, the recorder is available at 192.168.1.100 with the subnet mask

of 255.255.255.0. The displayed menu allows you to change the settings after uncheck the GET IP

ADDRESS FROM DHCP box and the GET DNS AUTOMATICALLY field. The following network

recorder settings are available, such as: IP (default 192.168.1.100) Subnet mask (default setting is

255.255.255.0). If the NVR needs to be connected to the Internet (for remote access, sending emails,

etc.), the IP addresses for Gateway and for Primary and Secondary DNS. You can change the default

HTTP and HTTPS ports intended for displaying the device's web panel as well as RTSP ports and

server data port. The parameter changes should be confirmed with the NEXT button

NVR OPERATING

NVR-6316-H2-II

User’s manual (Short) ver.1.0

15

II. Add Camera: Allows you to configure the camera and add them to the recorder. Upper window

displays a discovered camera by the NVR. To change the addressable cameras, click on the icon in

the column EDIT (This works with cameras NOVUS IP 3000 and 6000 series only).

Enter the address in the IP ADDRESS and set the masks in the SUBNET MASK then press the OK

button to save the settings.

Press the button to add a camera to the system.

Added camera will be displayed on the bottom of the menu list. To edit the connection settings of the

camera, press the EDIT column.

NVR OPERATING

NVR-6316-H2-II

User’s manual (Short) ver.1.0

16

If you are having problems connecting to the camera, you must enter the correct user name in the

USER NAME and password in the PASSWORD field and then press the OK button to save the

settings. If the NVR is connected to the camera STATUS is displayed as Connected. To remove a

camera from the list, press the in DELETE column.

IV. Record Settings :

You can set one of the modes:

MANUAL RECORD SETTINGS - You can set the recording time from the moment you select the

manual recording from 1 minute to 1 hour or manually off recording.

AUTO - set all the cameras on one of the following modes :

- MOTION RECORD - starts recording after receiving motion detection information from the

camera.

- SENSOR RECORD - starts recording after alarm generated on alarm input

- MOTION RECORD + SENSOR RECORD - starts recording after motion detecion alarm and after

alarm from alarm inputs

NVR OPERATING

NVR-6316-H2-II

User’s manual (Short) ver.1.0

17

- ALWAYS(24x7) RECORD +MOTION RECORD - constant recording and recoring after receiving

motion detection information from the camera.

- ALWAYS(24x7) RECORD + SENSOR RECORD - constant recording and recording alarm

generated on alarm input

- ALWAYS(24x7) RECORD + MOTION RECORD + SENSOR RECORD - constant recording and

recording alarm generated on alarm input and after receiving motion detection information from the

camera.

- ALWAYS(24x) RECORD + MOTION RECORD + SENSOR RECORD + ANALYTICS RECORD-

constant recording, recording alarm generated on alarm input, after receiving motion detection

information from the camera and after analytics alarm .

By clicking the ADVANCED button you can create your own combination of recording modes.

V. QR Codes : This menu allows you to scan a QRcode in the Supelive plus application or enter a

device code to autonat.com site. The service allows you to connect to a device connected to the Internet

network is behind a router equipped with NAT. To start connecting P2P network please select NAT

checkbox.

NOTE: AAT SYSTEMY BEZPIECZEŃSTWA sp. z o.o. is not responsible for the operation of the service

autonat.com which is provided by third parties.

NVR OPERATING

NVR-6316-H2-II

User’s manual (Short) ver.1.0

18

4. NVR MENU

4.1. Live monitoring

NOVUS network video recorders features a multilingual OSD menu allowing to adjust the settings of

the device. Available languages are: English, Polish, and others

As soon as the NVR completes its initialization process, it will enter the real-time monitoring image.

Displaying all cameras simultaneously is the default mode. On the bottom of screen STATUS BAR is

displayed.

To start access to the NVR click on the button to launch the start menu.

After clicking log on to the system (the default password for the root user is a "pass").

STATUS BAR description:

NVR MENU

Item Icon Description

Analytics

Launches the inteligent analysis menu

Search and

Bcakup

Launches search and backup menu

Playback

Starts playback menu

MENU BAR

VIDEO WINDOW

VIEW MENU

START MENU

NVR-6316-H2-II

User’s manual (Short) ver.1.0

19

Menu bar icons

NVR MENU

Item Icon Description

Settings Click to run conguration of NVR parameters

Logout

Starts playback menu

Shutdown

Shutdowns the the NVR

Item Icon Description

Settings Click to open start menu

Full screen

Switches video view to full screen

Division selection

Select 1,4,9 and 16 division

Additional division

Open additional division selection

Other divisions

1+ 12,1+5,1+7 additional views

Dwell

Starts displaying images in sequence

Dwell settings

Start/Stop time setting switch

NVR-6316-H2-II

User’s manual (Short) ver.1.0

20

View menu

Detailed information about configuration, service and installation of device is available in full

version of user's manual located on the www.novuscctv.com

NVR MENU

Item

Icon Description

OSD ON/OSD OFF

Turns on/off OSD information

Playback

Starts playback for displayed cameras

Manual Record

Turn on / off manually recording channels.

Manual Alarm

Allow to trigger the alarm manually.

Recording Status

Displays information about the recording

Alarm Status

Displays the status of alarm devices

Disc Status

Information about disc status

Network status

View information about network usage

Device Information

Displays information about the state of operation of the

basic components of recorder

Item Icon Description

Camera List of cameras to display

Single Channel Sequenc-

es

Select a group of cameras to display in single channel

Customize Displays

Modes

Customize display and save settings

Strona się ładuje...

Novus NVR-6316-H2-II Instrukcja obsługi

Novus NVR-6316-H2-II Instrukcja obsługi

w innych językach

Powiązane artykuły

Inne dokumenty