Novus NVR-6332-H2/F Instrukcja obsługi

U ser’ s ma n u a l

Manual for devices with firmware version 1.3.4

or lower

NVR-6332-H2

NVR-6316-H1

NVR-6308P8-H1

NVR-6304P4-H1

NVR-6332P16-H4

NVR-6332-H8

6000 series IP recorders - User’s manual - version 1.2

2

EMC (2004/108/EC) and LVD (2006/95/EC ) Directives

CE Marking

Our products are manufactured to comply with requirements of following directives and

national regulations implementing the directives:

• Electromagnetic compatibility EMC 2004/108/EC.

• Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well

as 75VDC and 1500VDC.

WEEE Directive WEEE 2012/19/EU Information on Disposal for Users of Waste Electrical and

Electronic Equipment

This appliance is marked according to the European Directive on Waste Electrical and

Electronic Equipment (2002/96/EC) and further amendments. By ensuring this product is

disposed of correctly, you will help to prevent potential negative consequences for the

environment and human health, which could otherwise be caused by inappropriate waste

handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance

may not be treated as household waste. It shall be handed over to the applicable collection point for the

waste electrical and electronic equipment for recycling purpose. For more information about recycling

of this product, please contact your local authorities, your household waste disposal service or the shop

where you purchased the product.

RoHS Directive RoHS 2011/65/EU

Concerning for human health protection and friendly environment, we assure that our

products falling under RoHS Directive regulations, regarding the restriction of the use of

hazardous substances in electrical and electronic equipment, were designed and manufactured

in compliance with mentioned regulation. Simultaneously, we claim that our products were

tested and do not contain hazardous substances exceeding limits which could have negative impact on

human health or natural environment.

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed

for self installation in households by individuals without technical knowledge.

The manufacturer is not responsible for defects and damages resulted from improper or inconsistent

with user’s manual installation of the device in the system.

ATTENTION!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT PROVISIONED FOR THE

GIVEN PRODUCT IN ITS USER’S MANUAL AND OTHER DOCUMENTS DELIVERED

WITH THE PRODUCT, OR THAT ARISES FROM THE NORMAL APPLICATION OF THE

PRODUCT, ITS MANUFACTURER MUST BE CONTACTED OR THE RESPONSIBILITY

OF THE MANUFACTURER FOR THE RESULTS OF SUCH AN ACTION SHELL BE

EXCLUDED.

IMPORTANT SAFEGUARDS AND WARNINGS

6000 series IP recorders - User’s manual - version 1.2

3

1. Prior to undertaking any action please consult the following manual and read all the safety and

operating instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual

is necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the

user’s manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is

forbidden;

7. You are not allowed to use the device in high humidity environment (i.e. close to swimming pools,

bath tubs, damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.)

is not recommended since it may lead to heat build-up and damaging the device itself as a

consequence;

9. Mounting the device on unstable surface or using not recommended mounts is forbidden.

Improperly mounted device may cause a fatal accident or may be seriously damaged itself. The

device must be mounted by qualified personnel with proper authorization, in accordance with this

user’s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with

those specified by the producer in the devices technical datasheet. Therefore, it is forbidden to

supply the devices from a power sources with unknown parameters, unstable or not meeting

producer’s requirements;

11. You cannot allow any metal objects get inside the recorder. It might cause serious damage. If a

metal object gets inside the device contact the authorised Novus service immediately.

12. The manufacturer does not bear responsibility for damage or loss of data stored on HDDs or other

media occurred during the usage of the product.

Due to the product being constantly enhanced and optimized, certain parameters and functions

described in the manual in question may change without further notice.

We strongly suggest visiting the www.novuscctv.com website in order to access the newest manual .

Technical changes reserved without prior notice and printing errors possible.

IMPORTANT SAFEGUARDS AND WARNINGS

6000 series IP recorders - User’s manual - version 1.2

4

PRELIMINARY INFORMATION

This instruction manual contains detailed information concerning the operation of the 6000 series

IP recorders.

Pictures in this publication showing camera views can be simulations. Actual camera

images may vary depending on the type, model, settings, observation area, or

environmental conditions.

The company AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o. has made every effort to

ensure that the information contained in this publication is comprehensive, accurate and

current.

However, due to the continuous development of the product line, graphic design, menu

layout or function descriptions contained in this publication may differ from those

implemented in your device. This does not limit or void this manual.

The following chapters describe all the functionalities present in the 6000 series IP

recorders. However, depending on your recorder model and/or firmware version, some of

the functions may be unavailable or not supported.

Technical data of the recorder, construction description, disk mounting method, first start

of the recorder and basic operation are included in the “Quick Start Guide” attached to

the recorder. When using this “User's Manual”, always have a quick start guide nearby so

that you can refer to it in matters not described in the user’s manual.

PRELIMINARY INFORMATION

6000 series IP recorders - User’s manual - version 1.2

5

1. BASIC CONFIGURATION ........................................................................................................... 7

1.1. Language change ..................................................................................................................... 7

1.2. Menu operating ........................................................................................................................ 7

1.3. Initial configuration ................................................................................................................. 9

1.4. Live preview .......................................................................................................................... 15

1.5. Searching and playing recorded video .................................................................................. 18

2. NVR MENU ................................................................................................................................... 18

2.1. Menu system ........................................................................................................................... 18

2.1.1. Basic. ......................................................................................................................... 19

2.1.1.1. General Settings ................................................................................................. 19

2.1.1.2. Date and Time ................................................................................................... 20

2.1.1.3. Output Settings .................................................................................................. 21

2.1.2. Maintenance ............................................................................................................... 22

2.1.1.2. View Log ............................................................................................................ 22

2.1.2.2. Factory default .................................................................................................... 23

2.1.2.3. Upgrade .............................................................................................................. 23

2.1.2.4. Backup and Restore ............................................................................................ 23

2.1.3. Information ............................................................................................................... 23

2.1.3.1. Basic ................................................................................................................... 23

2.1.3.2. Camera Status ..................................................................................................... 23

2.1.3.3. Alarm Status ....................................................................................................... 24

2.1.3.4. Record Status ...................................................................................................... 24

2.1.3.5. Network Status ................................................................................................... 24

2.1.3.6. Disk .................................................................................................................... 25

2.2. Camera ................................................................................................................................... 26

2.2.1. Manage Camera ......................................................................................................... 26

2.2.1.1. Add Camera ........................................................................................................ 27

2.2.1.2. Add Manually ..................................................................................................... 28

2.2.1.3. Add Group ......................................................................................................... 28

2.2.2. Image .......................................................................................................................... 29

2.2.2.1. OSD Settings ...................................................................................................... 29

2.2.2.2. Image Settings .................................................................................................... 29

2.2.2.3. Mask Settings ..................................................................................................... 29

2.2.3. Motion Settings ........................................................................................................... 30

2.2.4. Intelligence Analysis .................................................................................................. 31

2.2.4.1. Object Detection ................................................................................................. 33

2.2.4.2. Exception ............................................................................................................ 34

2.2.4.3. Tripwire .............................................................................................................. 35

2.2.4.4. Intrusion ............................................................................................................. 36

2.2.5. PTZ ............................................................................................................................. 37

2.2.5.1. Preset .................................................................................................................. 37

2.2.5.2. Cruise .................................................................................................................. 38

2.3. Record ............................................................................................................................ 39

2.3.1. Mode Settings ........................................................................................................ 39

2.3.2. Mode Settings ........................................................................................................ 40

2.3.3. Parameters ............................................................................................................. 40

2.3.3.1. Event recording parameters ................................................................................ 40

2.3.3.2. Schedule recording settings ................................................................................ 41

2.3.4. Stream Settings ...................................................................................................... 41

2.3.4.1. Sub Stream Settings ............................................................................................ 41

2.3.5. Record Settings ...................................................................................................... 41

TABLE OF CONTENTS

6000 series IP recorders - User’s manual - version 1.2

6

2.4. Alarm ............................................................................................................................ 40

2.4.1. Event Notification ................................................................................................. 40

2.4.1.1. Alarm-out ........................................................................................................... 40

2.4.1.2. E-mail ................................................................................................................. 41

2.4.1.3. Display................................................................................................................ 41

2.4.1.4. Buzzer ................................................................................................................. 41

2.4.2. Motion Alarm ........................................................................................................ 42

2.4.3. Sensor Alarm ......................................................................................................... 43

2.4.4. Exception ............................................................................................................... 43

2.4.4.1. IPC Offline Settings ........................................................................................... 43

2.4.4.2. Exception Handling Settings .............................................................................. 43

2.4.5. Alarm Status .......................................................................................................... 44

2.5. Disk ............................................................................................................................... 42

2.5.1. Disk Management .................................................................................................. 44

2.5.2. Storage Mode ........................................................................................................ 45

2.5.3. Disk ....................................................................................................................... 46

2.5.4. S.M.A.R.T. Information ........................................................................................ 47

2.6. Network ....................................................................................................................... 46

2.6.1. TCP/IPv4 ............................................................................................................... 47

2.6.2. Port ........................................................................................................................ 48

2.6.3. DDNS .................................................................................................................... 49

2.6.4. E-mail .................................................................................................................... 47

2.6.5. UPnP ...................................................................................................................... 48

2.6.6. NAT ....................................................................................................................... 48

2.6.7. Telnet ..................................................................................................................... 48

2.7. Account and Authority ............................................................................................... 48

2.7.1. Add User................................................................................................................ 48

2.7.2. Edit User ................................................................................................................ 49

2.7.3. Edit Group ............................................................................................................. 50

2.7.4. Security .................................................................................................................. 41

2.7.4.1. Black and white list ............................................................................................ 51

3. NETWORK AND OPERATION UTILIZING WEB BROWSER ............................ 52

3.1. Recommended PC specification for web browser connections ..................................... 52

3.2. Establishing connection ................................................................................................. 52

3.3. Live view panel .............................................................................................................. 53

3.4. Playback panel ............................................................................................................... 56

3.5. Backup panel ................................................................................................................. 57

3.6. Function panel................................................................................................................ 58

4. REMOTE ACCESS CONFIGURATION .................................................................... 59

Note :

Words like “clik”, “press”, “hold” used in that manual refers to virtual buttons available either in NVRs menu or in web

interface.

TABLE OF CONTENTS

6000 series IP recorders - User’s manual - version 1.2

7

1. BASIC CONFIGURATION

1.1. Language change

If after NVR booting up the currently selected menu language is different than expected, to change it,

please follow the steps below:

Click-on bottom left on start menu button .

Then select menu options to open (third from the bottom)

In the NVR menu, select the tab SYSTEM

In the displayed menu, select the English language in the third from the top of the box and click the

button on the bottom menu.

After saving settings, the language will be switched to English.

NVR OPERATING

6000 series IP recorders - User’s manual - version 1.2

8

1.2. Menu operating

To operate the menu press the button at the bottom left of the screen.

Then click-on LOGIN position

Then in login window please provide password for user root (default password for root user is pass)

and then press LOGIN button

NVR OPERATING

6000 series IP recorders - User’s manual - version 1.2

9

1.3. Initial configuration

Prior to using NVR for the first time, initial setup is strongly advised. Before you connect the IP

cameras to the NVR, please set up network and stream parameters of IP cameras in the right way.

Note:

For suggested values for IP camera setting please refer to the “Cameras Capability Table” available

on the www.novuscctv.com website. If you set wrong values some problems may appear: the NVR

cannot search the IP camera, the stream cannot be connected, the image is not fluent, the image

quality is bad and so on.

In case of first NVR start WIZARD SETUP menu window will occur (if function wasn’t disabled

earlier). To configure NVR please follow procedure like below, after finishing all the steps you’ll be

ready to work:

Provide username and password and click on NEXT button so start wizard.

STARTING THE DEVICE

6000 series IP recorders - User’s manual - version 1.2

10

I. Network Settings : This menu allows to set up networking. Default IP configuration is

192.168.1.100 netmask 255.255.255.0 . For NVRs with build in PoE switches (NVR-6304P4-H1 i

NVR-6308P8-H1) it is necessary to configure IP address for switch in INTERNAL ETHERNET

PORT SECTION. Please note that IP subnet for the ETHERNET PORT 1 and INTERNAL

ETHERNET PORT were different. In cases where it is necessary to NVRa connection to the Internet

(for remote access, email sending, etc.), Configure the following parameters: Gateway, Primary and

Secondary DNS. You can also enable DHCP mode allows you to download an IP address from a

DHCP server (required if running a DHCP server). It is possible to change the default HTTP port

designed to display panel Web device and RTSP ports and port server data. After changing parameter

pres NEXT button.

STARTING THE DEVICE

6000 series IP recorders - User’s manual - version 1.2

11

II. QR Codes : This menu allows to you to scan a QRcode in the Supelive plus application or enter a

device code to autonat.com site. The service allows you to connect to a device connected to the

Internet network is behind a router equipped with NAT.

NOTE: AAT Holding S.A is not responsible for the operation of the service autonat.com which is

provided by third parties.

III. Add Camera: Allows you to configure the camera and add them to the recorder. Upper window

displays a sophisticated camera by the NVR. To change the addressable cameras, click on the

icon in the column EDIT (This works with cameras NOVUS IP 3000 series).

STARTING THE DEVICE

6000 series IP recorders - User’s manual - version 1.2

12

Enter the address in the IP ADDRESS and set the masks in the SUBNET MASK then press the OK

button to save the settings.

Press the button to add a camera to the system.

Added camera will be displayed on the bottom of the menu list. To edit the connection settings of the

camera, press the EDIT column.

If you are having problems connecting to the camera, you must enter the correct user name in the

USER NAME and password in the PASSWORD field and then press the OK button to save the

settings. If the NVR connected to the camera will be on STATUS will be displayed Connected. To

remove a camera from the list, press the in DELETE column.

STARTING THE DEVICE

6000 series IP recorders - User’s manual - version 1.2

13

IV.Disk Settings : In this tab displays information about the hard disk detected by the DVR.

Before starting work, you need to format the hard disk by selecting it in the list of drives and then

pressing FORMAT.

Formatting may take a few moments. After properly formatted STATUS field should have a value of

„RW” (Read/Write).

V. Record Settings :

You can set one of the modes:

- MANUAL RECORD SETTINGS - You can set the recording time from the moment you select the

manual recording from 1 minute to 1 hour or manually off recording.

STARTING THE DEVICE

6000 series IP recorders - User’s manual - version 1.2

14

• AUTO - set all the cameras on one of the following modes :

- MOTION RECORD - starts recording after receiving motion detection information from the

camera.

- SENSOR RECORD - starts recording after alarm generated on alarm input

- MOTION RECORD + SENSOR RECORD - starts recording after motion detecion alarm and after

alarm from alarm inputs

- ALWAYS(24x) RECORD +MOTION RECORD - constant recording and recoring after receiving

motion detection information from the camera.

- ALWAYS(24x) RECORD + SENSOR RECORD - constant recording and recording alarm

generated on alarm input

- ALWAYS(24x) RECORD + MOTION RECORD + SENSOR RECORD - constant recording and

recording alarm generated on alarm input and after receiving motion detection information from the

camera.

STARTING THE DEVICE

6000 series IP recorders - User’s manual - version 1.2

15

1.4. Live preview

NOVUS network video recorders features a multilingual OSD menu allowing to adjust the settings of

the device. Available languages are: English, Polish, and others

As soon as the NVR completes its initialization process, it will enter the real-time monitoring image.

Displaying all cameras simultaneously is the default mode. On the bottom of screen STATUS BAR is

displayed.

To start access to the NVR click on the button to launch the start menu.

After clicking log on to the system (the default password for the root user is a "pass").

STATUS BAR description:

MENU BAR

VIDEO WINDOW

VIEW MENU

START MENU

Item Icon Descripon

Search Launches search for recordings

Playback

Starts playback menu

Backup Starts backup menu

NVR OPERATING

6000 series IP recorders - User’s manual - version 1.2

16

Menu bar icons

Item Icon Descripon

Sengs Click to run conguraon of NVR parameters

Logout

Starts playback menu

Shutdown Starts backup menu

Item Icon Descripon

Sengs Click to open start menu

Full screen

Switches video view to full screen

Single view Start displaying camera in single view

Quad view Start displaying 4 cameras in video view

9 cam. View Start displaying 9 cameras in video view

Other divisions Opening video subdivisions

Other divisions Open 1 main + 5 or 7 addional views

Dwell Starts displaying images in sequence

Dwell sengs Start/Stop me seng switch

NVR OPERATING

6000 series IP recorders - User’s manual - version 1.2

17

View menu :

Detailed information about configuration, service and installation of device is available in full version

of user's manual located on the www.novuscctv.com

Item

Icon Descripon

OSD ON/OSD OFF

Turns on/o OSD informaon

Playback

Starts playback for displayed cameras

Manual Record

Turn on / o manually recording channels.

Manual Alarm

Allow to trigger the alarm manually.

Recording Status

Displays informaon about the recording

Alarm Status

Displays the status of alarm devices

Disc Status

Informaon about disc status

Network status

View informaon about network usage

Device Informaon

Displays informaon about the state of operaon of the

basic components of recorder

Item Icon Descripon

Camera List of cameras to display

Single Channel Sequences

Select a group of cameras to display in single channel

Customize Displays Modes Customize display and save sengs

NVR OPERATING

6000 series IP recorders - User’s manual - version 1.2

18

1.5. Searching and playing recorded video

To begin playback of recorded material, select the button to play in the live preview, you will

see the window below:

Choose the date from the calendar and press OK button. You can identify the type of the recording

data by the color in the bar.

• Green (Manual) : data saved by manual recording.

• Blue (Schedule) : continuous data recording.

• Yellow (Motion) : motion event data recording.

• Red (Alarm) : alarm event data recording.

To play the searched data simply double click a desired point on or press PLAY button.

To control playback, you can use the following buttons from the playback options:

Stop - stops replaying

Rewind - Starts playback backward using key-frames

Pause/Play - Stop/Pasue replay

Declaration/Acceleration - change of pace playback possible times (1/32, 1 / 16,1 / 8,1 / 4,1 / 2,

1,2,4,8,16,32)

GRAPH WITH RECORDING

CALENDAR

VIEW OPTIONS

REPLAY OPTIONS

NVR OPERATING

6000 series IP recorders - User’s manual - version 1.2

19

- Frame Forward/Backward : Jump forward/backward frame by frame

- +/- 30 seconds - jumps forward/backward 30 seconds in recording time

- Event list - displays a list of events (motion detection, alarm input activation) registered for the

selected channel

- Backup - start menu archiving recordings

- Backup status - displays the current status of archival recordings

- Back - close the replay menu

2. NVR MENU

2.1. Menu system

In order to change the system settings click-on button from left bottom of the menu and then

click-on the SETTINGS. The SYSTEM menu have the menu sections.

2.1.1. Basic

2.1.1.1. General Settings

You can set the following settings :

DEVICE NAME - allows to set device name

DEVIC NO. –sets the device number

LANGUAGE - allow to choose language for NVR menu

NVR OPERATING

6000 series IP recorders - User’s manual - version 1.2

20

VIDEO FORMAT - allow to choose PAL or NTSC mode

MAIN OUTPUT - allows to choose resolution from 1280x1024, 1920x1080, 3840x2160 modes.

ENABLE WIZARD - checking this field starts startup wizard after user login

LOG IN AUTOMATICLY - checking this field automaticly logs in uaser after NVR start

LOG OUT AUTOMATICALY - cheking the box log outs the user out of the system after the time

given in WAIT TIME .

To save the settings press APPLY button.

2.1.1.2 –Date and Time

After clicking-in DATE AND TIME menu the following menu appears :

For DATE and TIME settings following settings are available :

SYSTEM TIME - sets the date and time in NVR

DATE FORMAT selects for date format from : DD/MM/RRRR, RRRR/MM/DD, MM/DD/RRRR,

DD/MM/YYYY

For network time synchronization the following settings are available :

SYNCHRONUS - MANUAL mode allow user to set the time manually. NTP mode allows to enter

NTP server address or select one from the predefined list.

In TIME ZONE/DST section it’s possible to select TIME ZONE location.

DST - displays information whether time is set to summer time

NVR OPERATING

Strona jest ładowana ...

Novus NVR-6332-H2/F Instrukcja obsługi

Novus NVR-6332-H2/F Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty