Vermeiren Jazz S50 Instrukcja obsługi

VERMEIREN

Jazz S50

U S E R M A N U A L

M A N U E L D ' U T I L I S A T I O N

G E B R U I K S A A N W I J Z I N G

G E B R A U C H S A N W E I S U N G

M A N U A L E D I I S T R U Z I O N I

M A N U A L D E I N S T R U C C I O N E S

I N S T R U K C J A O B S

Ł

U G I

N Á V O D K O B S L U Z E

Instrukcje dla wyspecjalizowanego

No part of this manual may be reproduced in any form what so

ever (print, photocopy, microfilm or any other process) without

written permission of the publisher, or processed, duplicated or

distributed by using electronic systems.

Aucune partie de ce manuel ne peut être reproduite, sous

quelque forme que ce soit (imprimée, photocopie, microfilm ou

tout autre procédé) sans l'autorisation écrite du publicateur, ni

traitée, dupliquée ou distribuée à l'aide de systèmes

électroniques.

Alle rechten, inclusief vertaling, voorbehouden.

Niets uit deze handleiding mag geheel of gedeeltelijk in enige

vorm (druk, fotokopie, microfilm of ieder ander procedé) zonder

de schriftelijke toelating van de uitgever worden

gereproduceerd of met behulp van elektronische systemen

worden verwerkt, gekopieerd of verspreid.

Alle Rechte, auch an der Übersetzung, vorbehalten.

Kein Teil der Gebrauchsanweisung darf in irgendeiner Form

(Druck, Fotokopie, Mikrofilm oder einem anderen Verfahren)

ohne schriftliche Genehmigung des Herausgebers

reproduziert oder unter Verwendung elektronischer Systeme

verarbeitet, vervielfältigt oder verbreitet werden.

Il presente manuale non può essere riprodotto, neppure

parzialmente, con alcun mezzo (stampa, fotocopia, microfilm o

altro procedimento) senza l’autorizzazione scritta della casa

produttrice, né elaborato, duplicato o distribuito con l’ausilio di

sistemi elettronici.

traducción.

Se prohíbe la reproducción total o parcial del presente manual

de cualquier forma (impresión, fotocopia, microfilm o cualquier

otro procedimiento), así como la edición, copia o distribución

empleando sistemas electrónicos, sin el permiso escrito del

editor.

Wszelkie prawa zastrzeżone, łącznie z tłumaczeniem.

Żadna część niniejszej instrukcji nie może być powielana w

jakiejkolwiek formie (drukowanej, fotokopii, mikrofilmu ani

innej) bez pisemnej zgody wydawcy, nie może być również

przetwarzana, kopiowana ani rozprowadzana za pomocą

systemów elektronicznych.

Všechna práva vyhrazena, včetně překladu.

Šíření jakékoliv části tohoto katalogu jakýmkoliv způsobem

(tisk, kopie, mikrofilm nebo jiný způsob) bez písemného

souhlasu vydavatele, nebo zpracování, duplikace či distribuce

prostřednictvím elektronických systémů je zakázáno.

EN

Instructions for specialist dealer

This instruction manual is part and parcel of the

product and must accompany every product

sold.

Version: I, 2020-09

FR

Instructions pour les distributeurs

Ce manuel d'instructions fait partie du produit et

doit accompagner chaque produit vendu.

Version : I, 2020-09

NL

Instructies voor de vakhandelaar

Deze handleiding is deel van het product en

dient bij iedere product te worden geleverd.

Versie: I, 2020-09

DE

Hinweise für den Fachhändler

Diese Gebrauchsanweisung ist Bestand-teil des

Produkts und ist bei jeder Produkts

auszuhändigen.

Version: I, 2020-09

IT

Istruzioni per il rivenditore

Il presente Manuale di istruzioni è parte

integrante del prodotto e deve essere fornito

assieme alla prodotto.

Versione: I, 2020-09

ES

Instrucciones destinadas a los distribuidores

especializados

El presente manual de instrucciones es parte

integrante del producto y se debe adjuntar a

todas las producto que se vendan.

Versión: I, 2020-09

PL

sprzedawcy

Niniejsza instrukcja obsługi jest nieodłączną

częścią produktu i musi być dołączona do

każdego sprzedawanego produktu.

Wersja: J, 2020-09

CS

Pokyny pro specializovaného prodejce

Tento návod k obsluze je součástí dodávky a

musí být součástí každého prodaného

produktu.

Verze: I, 2010-09

Basic UDI: 5415174 122106Jazz S50 BF

Multi version: I, 2020-09

Language index

English

Français

Nederlands

Deutch

Italiano

Español

Polski

Czech

User manual

Manuel d'utilisation

Gebruiksaanwijzing

Bedienungshandbuch

Manuale di istruzioni

Manual de instrucciones

Instrukcja obsługi

Návod k obsluze

This page is intentionally left blank

Jazz S50

2020-09

Contents

1

EN

NL

Contents

Contents ..................................................................................................................... 1

Preface........................................................................................................................ 2

1 Your product .................................................................................................. 3

1.1 Accessories ................................................................................................... 3

2 Before use ..................................................................................................... 4

2.1 Intended use ................................................................................................. 4

2.2 Explanation of symbols ................................................................................. 4

2.3 General safety instructions ............................................................................ 4

2.4 Transport ....................................................................................................... 5

2.5 Folding/Unfolding the wheelchair .................................................................. 7

2.6 Mounting/Taking off the rear wheels (if available) ......................................... 7

2.7 Storage ......................................................................................................... 7

3 Using your wheelchair .................................................................................. 8

3.1 Mounting or removing of the footrests ........................................................... 8

3.2 Operating the brakes ..................................................................................... 8

3.3 Mounting or removing the armrests............................................................... 8

3.4 Transfer in and out the wheelchair .............................................................. 10

3.5 Riding the wheelchair .................................................................................. 10

4 Installation and adjustment........................................................................ 11

4.1 Tools ............................................................................................................ 11

4.2 Manner of delivery....................................................................................... 11

4.3 Adjusting the footrests ................................................................................. 11

4.4 Adjust the brakes ........................................................................................ 12

4.5 Pneumatic tyre changing ............................................................................. 12

5 Maintenance ................................................................................................ 14

5.1 Points of maintenance ................................................................................. 14

5.2 Maintenance instructions ............................................................................ 14

5.3 Troubleshooting .......................................................................................... 15

5.4 Expected lifespan ........................................................................................ 15

5.5 Reuse .......................................................................................................... 15

5.6 End of use ................................................................................................... 15

6 Technical specifications ............................................................................. 16

Jazz S50

2020-09

Preface

2

EN

NL

Preface

Congratulations! You are now owner of a Vermeiren wheelchair!

This wheelchair is made by qualified and committed personnel. It is designed and produced

according to high quality standards, guarded by Vermeiren.

Please read this manual carefully; it will help you to get familiar with the operation, capabilities

and limitations of your wheelchair. If you still have questions after reading this manual, do not

hesitate to contact your specialist dealer. He/she will be glad to help you.

Important note

To ensure your safety, and to prolong the lifetime of your product, please take good care of it and

have it checked and serviced on a regular basis.

This manual reflects the latest product developments. Vermeiren has the right to implement

changes to this type of product without any obligation to adapt or replace similar products

previously delivered.

Pictures are used to clarify the instructions in this manual. Details of the depicted product may

deviate from your product.

Information available

On our website http://www.vermeiren.com/ you will always find the most recent version of the

information in this manual. Please consult this website regularly for possible updates.

Visually impaired people can download the electronic version of this manual and have it read out

by means of a text-to-speech software application.

User manual For user and specialist dealer

Installation instructions For specialist dealer

Service manual for wheelchairs For specialist dealer

EC declaration of conformity

Jazz S50

2020-09

Your product

3

EN

NL

1 Your product

1.1 Accessories

The following accessories are available for the Jazz S50:

 Travel wheels (B86)

 Armrests (B05)

Contact your specialist dealer about other accessories. He will gladly advise you.

1 = Cross

2 = Handgrips

3 = Backrests

4 = Arm pads

5 = Armrests

6 = Driving wheels (rear wheels)

7 = Hand rims

8 = Brakes

9 = Tip cap

10 = Steering wheels (front wheels)

11 = Footrests

12 = Footplates

13 = Seat

14 = Location identification plate

3

4

5

11

13

14

2

9

7

6

8

1

12

10

Jazz S50

2020-09

Before use

4

EN

NL

2 Before use

2.1 Intended use

In this paragraph a brief description of the intended use of your wheelchair is given. Additionally,

relevant warnings are added to the instructions in the other paragraphs. In this way we would

like to make you aware of the possible misuse that may appear.

 Indications and contraindications: The user can propel the wheelchair by himself or have the

wheelchair pushed by an attendant. The wheelchair is intended for people with walking

difficulties or no walking abilities. The different types of fittings and accessories, and the

modular construction allow full use by aged persons and persons disabled by paralysis, loss

of limbs (leg amputation), limb defects or deformations, stiff or damaged joints, heart

insufficiencies and poor blood circulation, balance disturbances, cachexia (decrease in

muscle).

 The wheelchair is suited for indoor and outdoor use.

 The wheelchair is designed to transport one (1) person with a maximum weight of 130 kg. It is

not designed for transportation of goods or objects, nor for any use other than previously

described.

 Only use accessories and spare parts approved by Vermeiren.

 Please read all technical details and limits of your wheelchair in chapter 6.

 The warranty of this product is based on normal use and maintenance as described in this

manual. Damage to your product caused by improper use or lack of maintenance will cause

the warranty to lapse.

2.2 Explanation of symbols

Maximum weight of the user in kg

Indoor/outdoor use

Maximum safe slope in ° (degrees).

Type designation

2.3 General safety instructions

 Do not use your wheelchair if you are under influence of alcohol, medicines or other substances

that may influence your riding abilities.

 Be aware that some parts of your wheelchair may get very hot or cold due to ambient

temperature, solar radiation or heating devices. Be careful when touching. Wear protective

clothing if the weather is cold. When going outdoors, riding gloves can be used to improve the

grip on the hand rims.

 Do not modify your wheelchair in any way.

 To prevent injury and/or damage to your wheelchair, make sure that no objects and/or body

parts are caught in the spokes of the driving wheels.

Be aware that your wheelchair may interfere with some types of anti-theft systems, depending on

the settings used. This may cause the shop's alarm to go off.

Jazz S50

2020-09

Before use

5

EN

NL

2.4 Transport

2.4.1 Moving out of the way

The best way to move the wheelchair is to make use of the wheels and roll the wheelchair.

If this is not possible (e.g. when the rear wheels are taken off for transportation in a car), firmly

grasp the frame on the front and the handgrips. Do not use the foot- or armrests or the wheels to

grasp the wheelchair.

2.4.2 Transport by vehicle, as luggage

Risk of injury

 Make sure that that the wheelchair is properly secured to avoid injury to the passengers during

collision or sudden braking.

 NEVER use the same seatbelt to attach the wheelchair and passenger.

1. Fold the wheelchair to its most compact size according to the instructions in § 2.5.

2. Store the wheelchair and its wheels in the luggage compartment or behind the passenger seat.

If luggage and passenger compartments are NOT separated or enclosed, fasten the

wheelchair frame securely to the vehicle.

2.4.3 Transport by vehicle, as seat for user

Risk of injuries or damage

 The wheelchair has passed the crash of ISO 7176-19: 2008 and, as such, has been designed

and tested for use only as forward-facing seat in a motor vehicle.

 The wheelchair's pelvic belt alone is not suited as an occupant restraint belt.

The wheelchair is tested using the four-point strap-tie system and a 3-point occupant-restraint

system. Whenever feasible, use the seat of the vehicle and store the wheelchair in the cargo

area.

Steps to secure the wheelchair in a motor vehicle:

1. Check that the vehicle is equipped with a suitable wheelchair tie down and occupant-

restraint system, conform ISO 10542.

2. Check that the components of the wheelchair tie down and occupant restraint system are

not frayed, contaminated, damaged or broken.

3. If equipped with an adjustable seat and/or back tilt, make sure that the wheelchair user is

sitting as upright as possible. If the user's condition prevents this, a risk assessment should

be done to evaluate the user's safety during transit.

4. Remove all mounted accessories such as trays and respiratory equipment, and secure them

in a safe place.

5. Position the wheelchair facing forward in the travelling direction, centrally between the tie-

down rails mounted in the floor of the vehicle.

6. Mount the front securement straps according to the instructions of the strap-system

manufacturer at the indicated place (figure 1). This place is marked on the wheelchair with

a symbol (figure 2).

7. Roll back the wheelchair until the front straps are tight.

8. Apply the wheelchair brake.

9. Mount the back securement straps according to the instructions of the strap-system

manufacturer at the indicated place (figure 1). This place is marked on the wheelchair with

a symbol (figure 2).

WARNING

Jazz S50

2020-09

Before use

6

EN

NL

Figure 1 Figure 2

Steps to secure the wheelchair user:

1. Remove both arm rests.

2. If present, attach the wheelchair's pelvic belt.

3. Attach the occupant restraint belts according to the instructions of the strap-system

manufacturer.

4. Wear the pelvic belt low across the front of the pelvis, so that the angle of the pelvic belt is

within the preferred zone of 30° to 75° to the horizontal, similar to that shown below.

5. A steeper (greater) angle within the preferred zone is desirable.

6. Adjust the belt tightly according to the instructions of the strap-system manufacturer,

consistent with the user's comfort.

7. Ensure that the restraint belt connects in a straight line to the anchor point in the vehicle and

that no bends in the belt are visible, for instance at the axle of the rear wheel.

8. Install the arm rests, if desired. make sure that belts are not twisted or held away from the

body by wheelchair components such as arm rests or wheels.

PELVIC RESTRAINTS SHOULD MAKE FULL

CONTACT ACROSS THE FRONT OF THE BODY

NEAR THE JUNCTION OF THE THIGH AND

PELVIS

RESTRAINTS SHOULD NOT BE HELD

AWAY FROM BODY BY WHEELCHAIR

COMPONENTS SUCH AS ARMRESTS OR

WHEELS

Jazz S50

2020-09

Before use

7

EN

NL

2.5 Folding/Unfolding the wheelchair

Chance of pinching – Do not place fingers between the components of the

wheelchair.

To fold:

1. Fold or remove the footplates (see § 3.1).

2. Take the seat on the front side and backside and pull it up.

3. Push the handgrips to fold up the wheelchair further.

To unfold:

1. Position yourself behind the wheelchair.

2. Use the handgrips to open the wheelchair as much as possible.

3. Position yourself at the front of the wheelchair.

4. Push both seating tubes down until they are fixed in position.

2.6 Mounting/Taking off the rear wheels (if available)

To remove the rear wheels

1. Press and hold button (1) while sliding the wheel axle out of the

hole of the frame.

2. Repeat this for the other wheel and place the wheelchair gently

on the rear frame tubes.

To install the rear wheels

1. Take one of the rear wheels and lift the wheelchair on one side.

2. Press and hold button (1) while sliding the wheel into the axle

bushy.

3. Release the button to lock the wheel. Make sure it clicks into

place.

4. Repeat this for the other wheel.

5. Ensure that both wheels are firmly secured.

2.7 Storage

Make sure that your wheelchair is stored in a dry environment to prevent mould from

growing and the upholstery from being damaged, see also chapter 6.

CAUTION

Jazz S50

2020-09

Using your wheelchair

8

EN

NL

3 Using your wheelchair

Risk of injuries and/or damage



First read previous chapters and inform yourself about the intended use. Do NOT use your

wheelchair unless you have read and fully understood all instructions.

 In case of doubts or questions, do not hesitate to contact your local specialist dealer,

your care

provider or technical adviser to help you with this.



Make sure that your hands, clothes, belts, buckles or jewellery don’t get caught by wheels or

other moving parts, during use or adjustment.

3.1 Mounting or removing of the footrests

Risk of injury

 Check that the footrests are securely locked in place before use.

 Keep objects away from the footrests swing range while mounting or removing the footrests.

The mounting of the footrests is done as follows:

1. Hold the footrest sideways at the outside of the wheelchair

frame and mount the tube hood (1) into the frame.

2. Swing the footrest inwards until it clicks in position.

3. Swing the footplate downwards.

To take off the footrests:

1. Pull lever (2).

2. Swing the footrest to the outside of the wheelchair until it comes

loose from the guidance.

3. Pull the footrest from tube hood (1).

3.2 Operating the brakes

Risk of injury

 The brakes are not used to slow down the wheelchair during movements. Use the brake only

to prevent the wheelchair from unintended movements.

 Good operation of the brakes is influenced by wear and contamination of the tires (water, oil,

mud, …). Check the condition of the tires before each use.

 The brakes are adjustable and can wear. Check the operation of the brakes before each use.

 Make sure the wheelchair is on a flat horizontal surface before releasing the brakes. Never

release both brakes simultaneously.

To apply the brakes:

1. Push the brake lever (1) forward until you feel a distinctive

click.

To release the brakes:

1. Release one brake by pulling the lever (1) backwards.

2. Hold the hand rim of the released wheel with your hand.

3. Release the second brake by pulling the lever backwards.

3.3 Mounting or removing the armrests

Risk of injury

 Check that the armrests are securely locked in place before use.

 Keep fingers and clothes away from the bottom side of the armrest.

CAUTION

WARNING

Jazz S50

2020-09

Using your wheelchair

9

EN

NL

1. Mount the rear tube of the armrest in tube hood (1) (Fig A).

2. Make sure the armrest is mounted very well.

3. Fold the armrest forward.

4. Pull the lever (2) on tube hood (3) upwards (Fig B).

5. Click the front tube of the armrest (4) in tube hood (3) (Fig B).

To open and remove the armrest:

1. Pull lever (2) and pull the front of the armrest (1) upwards (Fig C).

2. Fold the armrest backwards.

3. To remove the armrest, pull the rear of the armrest from tube hood (3) (Fig D).

A

B

C

D

Jazz S50

2020-09

Using your wheelchair

10

EN

NL

3.4 Transfer in and out the wheelchair

Risk of injury and/or damage

 In case you cannot perform the transfer in a safe manner,

ask someone to assist you.

 Do not stand on the footplates.

1. Position the wheelchair as close as possible to the chair,

couch or bed to/from you wish to transfer.

2. Check both brakes from the wheelchair are in the on position.

3. Fold the footplates upwards to prevent standing on them.

4. If the transfer is on the side of the wheelchair, fold the

armrest on that side upwards (see § 3.3).

5. Transfer to/from the wheelchair.

3.4.1 Correct position in the wheelchair

Some recommendations for a comfortable use of the wheelchair:

 Position your backside as close as possible to the backrest.

 Make sure your upper legs are horizontal. If needed, adjust the length of the footrests

(see § 4.3).

3.5 Riding the wheelchair

Risk of injuries and damage

 Before every usage, make sure that:

o parking brakes are working properly.

o tires are in good condition, see §5.

 Prevent your fingers from being caught by the wheel spokes.

 Do not operate the hand rims with wet hands.

 Prevent entrapment of your hands on the hand rims when you pass small passages.

 Do NOT drive on slopes, obstacles, steps or kerbs larger than specified in §6.

 When you stop on a (small) slope, use your brakes.

 Make sure all four wheels touch the ground while riding up or down a slope.

 Take slopes as slow as possible.

 Always stay on the pavement when riding on public roads.

 Pay attention if the road has holes or gaps that may cause entrapment of the wheels.

 Avoid stones and other objects that may block the wheels.

 Make sure that the footplates do not touch ground while taking an obstacle.

 Do not use your wheelchair on an escalator.

 If available, wear your safety belt.



Always keep the swing range of the footplate in mind to prevent bystanders from being injured

or objects from being damaged.



If you don’t have enough experience riding your wheelchair, ask assistance of an attendant.

Keep your arms away from the wheels and keep your feet on the footplate.

 Stairs should always be negotiated with the help of two attendants.



Never try to use stairs that are not appropriate for wheelchairs.

3.5.1 Riding your wheelchair:

1. Release the brakes.

2. Take both hand rims at their highest position.

3. Lean forward and push the hand rims forward until your arms are straight.

4. Move your hands back to the top of the hand rims and repeat the movement.

CAUTION

WARNING

Jazz S50

2020-09

Installation and adjustment

11

EN

NL

4 Installation and adjustment

The instructions in this chapter are for the specialist dealer.

The Vermeiren Jazz S50 has been designed as wheelchair with a minimum of adjustments. There

is no need for extra stock of spare parts.

To find a service facility or specialist dealer near you, contact the nearest Vermeiren facility.

Risk of injuries and damage

 Use only the settings described in this manual.

 Variation of allowed adjustments can still change the stability of your wheelchair (tilt back or

sideways).

4.1 Tools

To set up the wheelchair the following tools are needed.

 Wrench set n° 7 to n° 22

 Allen key set n° 3 to n° 8

 Screwdriver Phillips head

4.2 Manner of delivery

The Vermeiren Jazz S50 shall be delivered with:

 1 frame with armrests, rear and front wheels (seat height of 500 mm)

 1 pair footrests

 Tools

 Manual

 Accessories (optional)

 Tyre pump

4.3 Adjusting the footrests

Risk of damage – Avoid that the footrests make any contact with the ground.

Keep a minimum distance from 60 mm above the ground.

Adjust the length of the footrests as follow:

1. Remove the screw (1).

2. Adjust the length of the footrest to a comfortable length.

3. Tighten the screw (1) properly.

WARNING

CAUTION

Jazz S50

2020-09

Installation and adjustment

12

EN

NL

4.4 Adjust the brakes

Risk of injury – Brakes may only be adjusted by your specialist dealer.

1. Install the wheels according to § 2.6.

2. Disconnect the brakes by pulling lever (1) backwards (Fig A).

3. Loosen bolt (2) so the brake mechanism can slide over the frame (3) (Fig B).

4. Pull the brake mechanism over the frame (3) to the desired position (Fig B). The adjustment

of the brakes shall be in the range of the marked dashes (4) on the brake mechanism.

5. Retighten the bolt (2) (Fig B).

6. Check working of the brakes.

7. If necessary repeat the above steps until the brakes are adjusted well.

4.5 Pneumatic tyre changing

Risk of injury and/or damage

 If handled improperly, the rim might be damaged. Rather let an expert perform these activities.

 When mounting a tyre, make sure no objects or body parts are pinched between the tyre and

the rim.

 When inflating the tyres, always check that the pressure is correct. The correct pressure is

given on the tyre walls.

 Use only inflating equipment which complies with regulations and indicates the pressure in bar,

or use the supplied air pump. We do not accept any liability for damage caused by inflating

equipment not supplied by the manufacturer.

 Always make sure that the wheels are sufficiently inflated, since it could affect the

driving behaviour.

 We do not accept any liability for wheels not supplied by the manufacturer.

 Only an expert can guarantee correct assembly. Work not done by your specialist

dealer, would void the warranty of claims.

If you want to change the tyres or inner tubes, you should note the following:

1. Let all the air out of the inner tube.

2. Insert a tyre lever between the tyre and the rim.

3. Slowly and gently push the tyre lever downwards. This will pull the tyre over the edge of the

rim.

4. Then move the lever along the rim, the tyre will jump out.

5. Now carefully remove the tyre from the rim and then remove the tube.

Before replacing the tyre, check the rim bed and the inside wall of the tyre for foreign matter and

clean these properly if necessary. Check the condition of the rim bed, especially around the

position of the air valve.

A

B

WARNING

CAUTION

Jazz S50

2020-09

Installation and adjustment

13

EN

NL

Please use only genuine original replacement parts. We do not accept any liability for damage

caused by non-genuine parts. Kindly contact your specialist dealer.

Place the rim belt in position over the air valve before inserting it into the rim.

Then the rim belt can be pulled over easily. Check that all spoke heads are

covered (a rim belt is not required in the case of a plastic rim).

Push the tyre over the edge of the rim, starting behind the air valve. Inflate the

tube slightly until it is round, and place it inside the tyre.

If the tube fits snugly inside the tyre without any folds (in the case of folds: let

out some air), then the upper side of the tyre can be pressed lightly onto the rim

with both hands, starting at the air valve.

Check all around on both sides that the tube is not pinched between the rim and the edge of the

tyre. Lightly push the air valve inwards and pull it out again to make sure that the tyre is positioned

properly in the region of the air valve.

To ensure that the wheel inflated correctly, admit only so much air initially that the tyre can still be

easily pushed inwards by using your thumbs. If the check-lines are equidistant from the edge of

the rim on both sides of the tyre, then the tyre is centred properly. If not - let out the air and position

the tyre afresh.

Now the tyre can be inflated to its full operating pressure (note the maximum!!) and the valve cap

should be replaced.

Jazz S50

2020-09

Maintenance

14

EN

NL

5 Maintenance

5.1 Points of maintenance

Risk of injuries and damage

Repairs and replacements may only be undertaken by trained persons and only genuine

replacement parts of Vermeiren should be used.

The service frequency depends on the frequency and intensity of use. Contact your dealer

to agree to a common timetable for inspection/maintenance/repair.

Before each use

Inspect the following points:

 All parts: Present and undamaged or unworn.

 All parts: Clean, see § 5.2.2.

 Wheels, backrest, seat, calf rests, arm rests, footplate: Well secured.

 Condition of wheels/tyres, see § 5.2.1;

 Condition of frame parts: No deformation, instability, weakness or loose connections

 Seat, backrest, arm pads, calf pads and head rest (if applied): No excessive wear (like

dented spots, damage or tears).

 Brakes: Undamaged and functioning

Contact your specialist dealer for possible repairs or part replacements.

Yearly or more often

Have your wheelchair inspected and serviced by your specialist dealer, at least once a year, or

more often. The minimum maintenance frequency depends on use and should therefore be

commonly agreed on with your specialist dealer.

5.2 Maintenance instructions

5.2.1 Wheels and tyres

Proper working of the brakes depends on the state of the tyres, and can change due to

wear and contamination (water, oil, mud, …).

Keep your wheels free of wires, hair, sand and fibres.

Check the profile of the tyres. If the tread depth is less than 1 mm, the tyres need to be replaced.

Contact your specialist dealer for this matter.

Inflate each pneumatic tyre to the correct pressure (see pressure indication on the tyres).

5.2.2 Cleaning

Risk of damage by moisture



Never use a hose or high

-

pressure cleaner to clean the wheelchair.

Wipe all rigid parts of the wheelchair with a damp cloth (not drenched).

If necessary, use a mild soap, suitable for varnishes and synthetics.

The upholstery can be cleaned with lukewarm water and a mild soap. Do not use abrasive

cleaning agents to clean.

CAUTION

Jazz S50

2020-09

Maintenance

15

EN

NL

5.2.3 Disinfection

Risk of damage



Disinfections may only be

undertaken by trained persons. Consult your specialist dealer.

5.3 Troubleshooting

Even if you use your wheelchair properly, a technical problem may occur. If this is the case,

contact your local specialist dealer.

Risk of injuries and damage to the wheelchair



NEVER attempt to repair the wheelchair yourself.

The following symptoms may indicate a serious problem. Therefore always contact your specialist

dealer if you spot any of the following deviations:

 Strange sound;

 Uneven tread wear on one of the tyres;

 Jerky movements;

 Wheelchair deflects to one side;

 Damaged or broken wheel assemblies.

5.4 Expected lifespan

The average lifespan of your wheelchair is 5 years. Depending on the frequency of use, driving

circumstances and maintenance, the lifespan of your wheelchair will increase of decrease.

5.5 Reuse

Before each reuse, have the wheelchair disinfected, inspected and serviced according to the

instructions in §5.1 and §5.2.

5.6 End of use

At end of life, you need to dispose your wheelchair according to the local environmental

legislation. The best way to do so, is to disassemble the wheelchair to facilitate the transport of

recyclable parts.

CAUTION

WARNING

Jazz S50

2020-09

Technical specifications

16

EN

NL

6 Technical specifications

The technical details below are only valid for this wheelchair, at standard settings and optimal

ambient conditions. Take these details into account during use.

The values are no longer applicable if your wheelchair has been modified, damaged or suffers

from severe wear.

Table 1: Technical specifications

Make

Vermeiren

Type

Manual wheelchair

Model

Jazz S50

Description

Jazz S50 Kids

Jazz S50

Maximum occupant mass 60 kg 130 kg

Overall length with footrest 914 mm 1120 mm

Effective seat width 330 mm

370 mm

390 mm

420 mm

440 mm

460 mm

480 mm

500 mm

Overall width (depends on the seat width)

518 mm

558 mm

565 mm

595 mm

615 mm

635 mm

655 mm

675 mm

Folded length without footrest 707 mm 825 mm

Folded width 299 mm 290 mm

Folded height 915 mm 935 mm

Total mass 15,20 kg 16,60 kg

Mass of heaviest part 7,50 kg 8,05 kg

Masses of parts that can be dismantled or

removed

Footrests: 1,80 kg; Armrests: 1,80 kg;

Rear wheels:

4,95 kg

Static stability downhill 15°

Static stability uphill 10°

Static stability sideways 15°

Effective seat depth 325 mm 450 mm

Seat surface height at front edge 457 mm 500 mm

Seat angle 5°

Backrest height 360 mm 420 mm

Backrest angle 0°

Distance between footrest and seat 317 - 366 mm 370 – 440 mm

Angle between seat and footrest 6° 7°

Distance between armrest and seat 211 mm 220 mm

Front location of armrest structure 235 mm 310 mm

Hand rim diameter 495 mm 535 mm

Horizontal location of axle (deflection) 10 mm

Minimum turning diameter 990 mm 1190 mm

Strona jest ładowana ...

Vermeiren Jazz S50 Instrukcja obsługi

Vermeiren Jazz S50 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty