Samsung SNC-B5395 Instrukcja obsługi

SNC-B5395

user manual

ENG RUS POL

imagine the possibilities

Thank you for purchasing this Samsung product. To receive

more complete service, please register your product at

www.samsung.com/global/register

Cover-B5395-AB68-00718E.indd 1 2008-07-14 오후 5:49:37

safety precautions

CAUTION

RISK OF ELECTRIC SHOCK. DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)NO USER-SERVICEABLE PARTS

INSIDEREFER SERVICING TO QUALIFIED SERVICE PERSONNEL

This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this

unit.

This symbol indicates that there are important operating and maintenance instructions in the literature

accompanying this unit.

WARNING

• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

• The camera is to be only connected to PoE networks without routing to the outside plant.

WARNING

1. Be sure to use only the standard adapter that is specified in the specification sheet.

Using any other adapter could cause fire, electrical shock, or damage to the product.

2.

Incorrectly connecting the power supply or replacing battery may cause explosion, fire,

electric shock, or damage to the product.

3.

Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause

abnormal heat generation or fire.

4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.

5.

When installing the camera, fasten it securely and firmly. A falling camera may cause personal

injury.

6.

Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or containers

filled with water on top of the camera. Doing so may cause personal injury due to fire, electric

shock, or falling objects.

7.

Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric

shock.

8.

If any unusual smells or smoke come from the unit, stop using the product. In such case,

immediately disconnect the power source and contact the service center. Continued use in

such a condition may cause fire or electric shock.

EU-B5395-ENG_080714.indd 2 2008-07-14 오후 3:46:59

9. If this product fails to operate normally, contact the nearest service center. Never disassemble

or modify this product in any way. (SAMSUNG is not liable for problems caused by

unauthorized modifications or attempted repair.)

10.

When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire

or electric shock.

CAUTION

1. Do not drop objects on the product or apply strong shock to it. Keep away from a location

subject to excessive vibration or magnetic interference.

2.

Do not install in a location subject to high temperature (over 50°C), low temperature (below

-10°C), or high humidity. Doing so may cause fire or electric shock.

3.

If you want to relocate the already installed product, be sure to turn off the power and then

move or reinstall it.

4.

Remove the power plug from the outlet when then there is a lightning. Neglecting to do so

may cause fire or damage to the product.

5. Keep out of direct sunlight and heat radiation sources. It may cause fire.

6. Install it in a place with good ventilation.

7.

Avoid aiming the camera directly towards extremely bright objects such as sun, as this may

damage the CCD image sensor.

8.

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,

such as vases, shall be placed on the apparatus.

9. The Mains plug is used as a disconnect device and shall stay readily operable at any time.

10.

When using the camera outdoors, moisture may occur inside the camera due to temperature

difference between indoors and outdoors. For this reason, it is recommended to install the

camera indoors. For outdoor use, use the camera with built-in fan and heater.

EU-B5395-ENG_080714.indd 3 2008-07-14 오후 3:46:59

important safety instructions

1. Read these instructions.

2.

Keep these instructions.

3.

Heed all warnings.

4.

Follow all instructions.

5.

Do not use this apparatus near water.

6.

Clean only with dry cloth.

7.

Do not block any ventilation openings.

Install in accordance with the manufacturer’s instructions.

8.

Do not install near any heat sources such as radiators, heat registers, or other apparatus

(including amplifiers) that produce heat.

9.

Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong.

The wide blade or the third prong is provided for your safety.

If the provided plug does not fit into your outlet, consult an electrician for replacement of the

obsolete outlet.

10.

Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11.

Only use attachments/accessories specified by the manufacturer.

12.

Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with

the apparatus.

13.

Unplug this apparatus. When a cart is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

14.

Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not operate normally,

or been dropped.

EU-B5395-ENG_080714.indd 4 2008-07-14 오후 3:46:59

Contents _01

contents

Preparation

03

Installation and Connection

08

Network Connection & Setup

26

Setting Static IP

36

Setting Dynamic IP

.40

03 Features

04 Precautions – Installation and Use

04

Recommended PC Specifications

04

Compatible IP Routers

05

Compatible PoE Switches

05

Checking the components in the package

06

Names of each part

08

Removing the cover

09

Setting switches

14

Installing camera

21

Connecting

27

Connecting the camera to an IP router with

the xDSL/Cable modem

30

Connecting the camera to an IP router with

local area networking

32

Connecting the camera directly to a DHCP-

based xDSL/Cable modem

34

Connecting the camera directly to local area

networking

35

Searching for the camera

36

Manual Network Setting

39

Automatic Network Setting

40

Dynamic IP Setting

41

Port Forwarding (Port Mapping) Setting

NA-B5395-ENG.indd 1 2008-07-14 오후 3:45:39

02_ Contents

Using the Camera

42

Setting Up

55

Appendix

77

42 Connecting to the camera

44 Installing ActiveX

46

Using the Viewer Screen

50

Using the Search Viewer Screen

55

Setting the camera

57

Basic Configuration

63

System Configuration

67

Layout Configuration

68

Event Configuration

75

Network Configuration

77

Troubleshooting

79

Specifications

NA-B5395-ENG.indd 2 2008-07-14 오후 3:45:39

Preparation _03

01 PREPARATION

FEATURES

Various Communication Protocol Support

This product supports various communication protocols such as ARP, HTTP and DHCP as well as

TCP/IP, UDP, SMTP for Email transmission and FTP protocol.

Monitoring Through Web Browser

Monitoring Through Web Browser This product enables watching a video through an Internet web

browser so that you can watch a video through the Internet as you can within the local network.

Automatic Local IP Setting Function

This function offers an easy way of configuring the network settings with a minimal key input for

those who are not familiar with it.

Alarm Function

If this product is connected with a motion sensor and the sensor detects a motion, a recorded

video clip is sent through the FTP/Email(SMTP) registered by the user or saved on the SDHC

memory card and a signal is sent to an alarm output port.

Motion Detection Function

If the user specifies a target area to monitor and the motion sensor detects a motion within that

area, a still image is sent to the FTP/Email(SMTP) server designated by the user or saved on the

SDHC memory card, and signals are sent to the alarm output terminal.

preparation

NA-B5395-ENG.indd 3 2008-07-14 오후 3:45:39

04_ Preparation

PRECAUTIONS – INSTALLATION AND USE

Do not disassemble your camera.

Always be cautious when handling your camera.

Do not subject the camera to impact or vibration and always be cautious of damaging the camera

due to neglectful storage and/or operation.

Do not install the camera at a location where it would become exposed to rain or humidity and do

not operate the camera in a wet environment.

Do not clean the camera’s main body using harsh abrasives or similar substances. If dirty, use a dry

piece of cloth to clean instead.

Install the camera in a shaded area or environment, protected from direct sunlight.

Direct sunlight exposure has a negative effect on the camera.

Do not bend or throw the SDHC memory card.

Do not store or use the SDHC memory card in a hot, humid, or dusty environment.

Protect the contacts of the SDHC memory card from foreign substance buildup.

If foreign substances have been built up on the contacts, remove using a soft piece of cloth.

When removing the SDHC memory card, disable SD Card Recording to protect against data loss

(refer to page 70 for instruction on disabling SD Card Recording).

Data cannot be stored on SDHC memory cards whose service life has expired.

Please purchase a new SDHC memory card if you experience this.

The manufacturer will not be held responsible for data loss incurred by the customer due to im-

proper use.

Using non-recommended PoE device may cause malfunction of either the camera or PoE device

itself. (Refer to page 5 for the compatible PoE Switch)

RECOMMENDED PC SPECIFICATIONS

CPU: Pentium4/2.4GHz or higher

Operating System: Windows XP(Service Pack2) / Windows Vista

Resolution: 1024X768 pixels or higher

RAM: 512MB or higher

Web Browser: Internet Explorer 6.0 or higher

Video Card: Radeon, Nvidia

Video Memory: 128MB

DirectX 8.1 or higher

COMPATIBLE IP ROUTERS

Linksys

D-Link

Netgear

NA-B5395-ENG.indd 4 2008-07-14 오후 3:45:39

Preparation _05

01 PREPARATION

COMPATIBLE POE SWITCHES

Linksys SRW224G4P

D-Link DES-1316

SMC SMCPWR-INJ3

CHECKING THE COMPONENTS IN THE PACKAGE

Make sure that the following items are included in the package.

Camera

User's Manual

Test Monitor Cable

CD

External Cable

Image Part name Standard Quantity Usage

PLASTIC ANCHOR HUD 5 4EA

Attach each piece to screw connection

holes for strengthening connection

ASSY SCREW

MACHINE

BH M5 X L6.

(WHITE+O RING)

8EA

Used for filling in the holes when installing

pipe and wall mount

ASSY SCREW

TAPPING

TH M4 X L30 (BLK+O

RING)

4EA

Used when installing your camera on the

ceiling or wall

L-Wrench TROX T-20 1EA

Used for assembling/ disassembling the

Dome cover

TEMPLATE 1EA Used for guiding the installation

Gasket-pipe hole T2.5 W56 1EA

Used to make a wiring hole when installing

the camera on the ceiling or wall

Ferrite-Core ZCAT2132-1130-M-K 1EA

Wrap the EMI suppression ferrite core with

the power adapter cord three times.

NA-B5395-ENG.indd 5 2008-07-14 오후 3:45:41

06_ Preparation

Front

1

Inner Cover

Covers the main body to protect it.

2

Dome Cover

Covers the inner cover, lens, and main body to protect them.

3

Main Body

Includes a lens, a switch board, a PCB board, screws, and

such.

4

Audio Out

For outgoing audio signals.

5

Audio In

For incoming audio signals.

6

Power Port

Connect the power cable to this port.

7

Video Out

For outgoing video signals from the camera.

This port connects to the monitor’s video in port.

When the camera lens becomes dirty, softly clean it with a lens tissue or a cloth soaked in pure

ethanol.

NAMES OF EACH PART

2

1

3

4

5

6

7

NA-B5395-ENG.indd 6 2008-07-14 오후 3:45:41

Preparation _07

01 PREPARATION

Inside

1

Ethernet Port

Ethernet cable port.

2

I/O Port

Used to connect the camera to an external device.

- ALARM IN : These are alarm in ports.

- ALARM OUT : These are alarm out ports.

- GND : This is the GND port.

3

SDHC Memory Card Slot

This is where you insert your SDHC memory card.

4

Function Switch

Used to set the camera function.

5

Reset Button

Reverts all camera settings to their default.

Refer to the Reset section for more information.

4

3

2

1

5

NA-B5395-ENG.indd 7 2008-07-14 오후 3:45:41

08_

Installation and Connection

REMOVING THE COVER

To connect the SDHC memory card, Ethernet cable, alarm input/output and etc., remove the

Dome Cover and Lens Cover.

1

Remove 4 screws using L-Wrench.

2

Lift the dome cover upward and

remove it.

3

Pull both sides of the lens cover and

lift it up to remove.

installation and connection

NA-B5395-ENG.indd 8 2008-07-14 오후 3:45:42

Installation and Connection

_09

02

INSTALLATION AND CONNECTION

SETTING SWITCHES

Setting function switches

To set the available functions on your camera, adjust eight switches as shown below:

No Name Brief description

1 N/A This is unavailable function.

2 LSS Sens-up or Low speed shutter ON/OFF

3 H-REV Horizontal reverse ON/OFF

4 V-REV Vertical reverse ON/OFF

5 BLC Backlight compensation ON/OFF

6 FL Flickerless ON/OFF

7 D/N Automatic switching between color and black & white ON/OFF

8 AWB Automatic white balance ON/OFF

2 Switch 2 (LSS) : This sens-up mode accumulates the image fields in memory to reduce

noise but increase the brightness and contrast rate. When this switch is set to ON, the

camera automatically switches to a maximum of 128 times of image acquisition speed to

implement a clear picture for darker image.

NA-B5395-ENG.indd 9 2008-07-14 오후 3:45:42

10_

Installation and Connection

3 Switch 3 (H-REV) : When this switch is set to ON, the camera image is reversed

horizontally. If you want to monitor your site using a mirror, you can use this feature to see

the right image.

4

Switch 4 (V-REV) : When this switch is set to ON, the camera image is reversed

vertically. If your camera reluctantly displays the vertically reversed image, you can use

this feature to see the right image.

5

Switch 5 (BLC) : When this switch is set to ON, you can view a clear image even though

the camera faces any excessive light such as sunlight and fluorescent light. When it is set

to OFF, the subject with excessive light is not clearly shown.

6

Switch 6 (FL) : When this switch is set to ON, the shutter speed is fixed to 1/100 sec

(for NTSC) or 1/120 sec (for PAL) to prevent screen from flickering by the disaccordance

between vertical synchronous frequency (50Hz for NTSC, 60Hz for PAL) and on-and-off

frequency of a light.

7

Switch 7 (D/N) : When this switch is set to ON, the camera automatically switches

between color and B&W according to the brightness of the vicinity.

8

Switch 8 (AWB) : This switch adjusts white balancing. When this switch is set to ON, this

camera operates in ATW mode, and in case of OFF, this camera operates in AWC mode.

ATW (Auto Tracking White Balance):

The color temperature is automatically adjusted according to the environmental change.

(Approx. 2000°K to 11,000°K)

A

WC (Auto White Balance Control):

It stores the color temperature just when the switch is changed to OFF. Accordingly color temperatures

are adjusted by the stored value.

NA-B5395-ENG.indd 10 2008-07-14 오후 3:45:42

Installation and Connection

_11

02

INSTALLATION AND CONNECTION

Inserting/Removing an SDHC Memory Card

Inserting an SDHC Memory Card

Push the SDHC memory card in the direction of the arrow shown in the diagram.

Do not force the memory card in. If you can’t insert the memory card into the slot with ease,

you might be inserting the card in the wrong direction. Forcibly inserting a memory card could

lead to its damage.

Removing an SDHC Memory Card

Gently press down on the exposed end of the memory card as shown in the diagram to eject

the memory card from the slot.

Pressing too hard on the SDHC memory card can cause the card to shoot out uncontrollably

from the slot when released.

When removing the SDHC memory card, disable the SD Card Recording feature (refer to

page 70 for instructions on disabling SD Card Recording).

Removing the SDHC memory card while recording is in progress can damage the data.

NA-B5395-ENG.indd 11 2008-07-14 오후 3:45:43

12_

Installation and Connection

Memory Card Information (not included)

What is a memory card?

The memory card is an external data storage device that has been developed to offer an entirely

new way to record and share video, audio, and text data using digital devices.

Selecting a memory card that’s suitable for you

Your camera supports SDHC memory cards.

You may, however, experience compatibility issues depending on the model and make of the

memory card.

Your camera supports SD memory cards.

However, the maximum supported SD memory card capacity is 2GB and ver 1.1, 4GB or

above SD memory cards are incompatible.

For your camera, we recommend you use a memory card from the following manufacturers:

SDHC/SD Memory Card: Panasonic®, SanDisk®, and Toshiba®

Your camera supports 128MB to 16GB of memory card capacity.

Playback performance can be affected depending on the speed of memory card, so use the

high-speed memory card. To ensure proper recording of video data, we recommend you use a

memory card that supports at least read/write speed 10Mbps and Class 6

Memory Card Use

SD and SDHC memory cards feature a switch that disables writing data on to the media.

Having this switch to the Lock position will prevent accidental deletion of data stored in the

memory card but at the same time will also prevent you from writing data on to the media.

Memory Card Components

SDHC

Lock Switch

Contacts

NA-B5395-ENG.indd 12 2008-07-14 오후 3:45:43

Installation and Connection

_13

02

INSTALLATION AND CONNECTION

Connecting Ethernet Cable

Connect the Ethernet cable to the network port as shown.



Connecting Molded Cable directly

Circuit Board can be affected by stress due to a limited space, which can cause a

malfunction. For this reason, use non-molded UTP cable when connecting directly to the

camera.



Connecting Molded Cable using UTP Cable

Connect the supplied UTP cable to the camera first, then connect molded cable to the

UTP cable.

< X > < O >

NA-B5395-ENG.indd 13 2008-07-14 오후 3:45:43

14_

Installation and Connection

INSTALLING CAMERA

Before installation

Before installing your camera, you have to read the following cautions:

You have to check whether the location (ceiling or wall) can bear five times the weight of your camera.

Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise

it may cause a breakdown or fire. You can use wall mount adaptor (SADT-102WM), and pole mount

adaptor (SADT-100PM) for installing the camera on the wall or pipeline.

When installing your camera, don’t allow any person to approach the installation site. If you have any

valuable things under the place, move them away.

About the installation holes

A: Use these holes when directly installing

your camera on the ceiling or wall.



While those are not used, fill in the holes

using the screw machine (M5 X L6.) for

waterproofing.

B: Use four holes when directly installing

your camera on the junction box



You can use the 4 1/8 diameter round

type junction box for assembly.

(The junction box, gasket, and cover are

separately purchased items.)

C: Use these holes when installing the wall

mount adapter (SADT-102WM)



While those are not used, fill in the holes

using the screw machine (M5 X L6.) for

waterproofing.

The holes that are not used should be tightly sealed up using the screws provided for

waterproofing. When the screws don’t have rubber rings inside or are not closely attached, note

that it can cause waterproofing problem. For attaching screws, see page 19 “Disassembling/

assembling the Main body from the Case.”

A

B

C

NA-B5395-ENG.indd 14 2008-07-14 오후 3:45:44

Installation and Connection

_15

02

INSTALLATION AND CONNECTION

Installing on a pipe

Before installation, you have to be familiar with the cautions on page 14 and fill in the holes

that are not used for installation. The holes that are not used should be tightly sealed up using

the screws provided for waterproofing. (Refer to page 14)

To install your camera bottom on a pipe

1

After connecting the power and video cables, throw them

inside the pipeline and screw the male thread pipe into the

female pipe thread in your camera tightly to fix the Main

body. (In this case, be sure to tape with Teflon tape before

assembly for waterproofing. Be careful for the wiring cable

not to be stuck in the connection area.)

2

Adjust the angle of the camera

in search of a better view.

1. Separate the Dome cover using the

L-Wrench provided.

(To make loose the screws, rotate

counterclockwise.)

2. Adjust the lens direction. For more

information, see page 20 “Adjusting

the camera direction.”

3

Attach the Dome cover.

(Screw the connection bolts

tightly using the L-Wrench for

waterproofing.))



To change the SAMSUNG logo

position, move the location of the

connection rubber band as show

below and rotate for assembly.

(The rotation limit is 180 degree.)

NA-B5395-ENG.indd 15 2008-07-14 오후 3:45:45

16_

Installation and Connection

To install the camera side on a pipe

1

Pull the power and video cables

through the pipe connection hole

on the camera side.

1. Remove the side cover from the

Case using a coin or minus (-) driver.

(Rotate counterclockwise.)

2. Push the power and video cables

stretched outside of the bottom hole

into the Case. And pull them out from

the side cover of the Case.

2

Attach the removed side cover to the bottom hole and

rotate it clockwise using a coin or minus (-) driver.

(Be sure to insert the O-ring (P22 T2.4) into the hole before

assembly. The ring is necessary for waterproofing.)

NA-B5395-ENG.indd 16 2008-07-14 오후 3:45:46

Strona jest ładowana ...

Samsung SNC-B5395 Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Samsung SNC-B5395 Instrukcja obsługi

Powiązane dokumenty

Inne dokumenty