Riva RC3202HD-6211(W) Instrukcja instalacji

Kategoria
Kamery ochrony
Typ
Instrukcja instalacji

Ten podręcznik jest również odpowiedni dla

www.rivatech.de
Specification subject to change without notice
RC3202HD-6111(W)
Installation Guide
Precaution
Please read this manual carefully before installing the unit.
Never disassemble the camera. Unauthorized disassembly may cause
equipment failure or damage to the unit.
Please do not install the camera in a place exposed to direct sunlight.
Do not operate the camera in environments beyond the specified
temperature.
Refer to Environment Conditionon
APPENDIX (A) : SPECIFICATIONS
in
this manual.
Before applying power to the camera, check the power source to ensure
that it is within the specifications. Refer to Electrical Characteristicson
APPENDIX (A) : SPECIFICATIONS
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 3
Table of Contents
Precaution .................................................................................. 2
1. FEATURES .............................................................................. 4
2. PACKAGE CONTENTS ................................................................ 6
3. PART NAMES .......................................................................... 7
4. INSTALLATION ......................................................................... 8
4.1. Installing the camera ..................................................................... 8
4.2. Adjusting the angle of the camera .................................................. 10
4.3. Setting the Image Attribute ........................................................... 11
4.4. Adjusting lens focus ..................................................................... 12
5. CONNECTIONS ...................................................................... 13
6. CONFIGURATION .................................................................... 16
6.1. Set up network environment ......................................................... 16
6.1.1. Generic IP Environment .......................................................... 16
6.1.2. Custom IP Environment .......................................................... 17
6.2. View video on web page ............................................................... 19
6.2.1. ActiveX Installation ................................................................ 19
6.2.2. View video using IPAdmin tool .................................................. 20
6.3. Reboot ...................................................................................... 21
6.4. Factory Default ........................................................................... 21
6.5. Safe Mode ................................................................................. 21
APPENDIX (A): SPECIFICATIONS .................................................... 24
Summary .......................................................................................... 24
Electrical Characteristics ..................................................................... 26
Environment Condition ........................................................................ 26
Mechanical Condition .......................................................................... 26
APPENDIX (B): POWER OVER ETHERNET ........................................ 27
PoE compatibility ................................................................................ 27
Power Comparison ............................................................................. 27
APPENDIX (C): DIMENSIONS ........................................................ 29
APPENDIX (D): HEXADECIMAL-DECIMAL CONVERSION TABLE ............. 30
REVISION HISTORY ..................................................................... 32
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 4
1. FEATURES
Camera
Full HD Compact Indoor Dome IP Camera
SONY EXMOR 1/2.9” 1080p CMOS Image Sensor
Digital Day / Night
WDR
Video
Video compression: H.264, MJPEG, 25/30FPS@1080p*
Dual streaming mode
Unicast/Multicast
Text Overlay
Network
10 / 100 Base-T Ethernet
RTSP/ HTTP protocol supported
Integration
Software Development Kit (SDK) available
ONVIF Compliant (Profile S)
General
Micro SD/SDHC slot
Power Over Ethernet (PoE)
Digital input/output supported (1/1ch)
Video Contents Analytics (VCA)
VCA Presence (Standard)
VCA Surveillance or other VCA extension license are available (Optional)
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 5
* If VCA is activated, frame rate is limit to max15fps@1080p. Limitation based on V.1.6.0
firmware release and could be changed without notice.
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 6
2. PACKAGE CONTENTS
Please unpack the package carefully and handle the equipment with care.
The package contains:
Camera
DC Power Adaptor
Universal Plugs
Screws and anchor blocks
Quick Installation Guide
Camera Opener
Ferrite Core
Installation Template
The contents above are subject to change without prior notice.
Note
i
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 7
3. PART NAMES
1 Reset button
Use the button to restart the device or to reset it to Factory Default.
Refer
to
6.3. Reset
and 6.4. Factory Default for more details.
2 Terminal Connector
Connector for cable connection of digital input/output. Refer to 5.Connections
for more details.
3 Micro SD/SDHC slot
Supports up to 64GB. Recommend Class 6 and higher for HD recordings.
4 LAN Connector
This is a RJ45 LAN connector for 10/100 Base-T Ethernet. (PoE supported)
5 Power Adaptor Connector
Use DC 12V adapter for power supply.
DO
DI
Out
In
Com
Com
DO
DI
Out
In
Com
Com
* Models herein and their appearance are subject to change without any prior notice.
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 8
4. INSTALLATION
4.1. Installing the camera
To prevent products from damage, place the camera on stable and
non-vibrating surfaces If the stability is in doubt, consult safety
personnel for reinforcements, and then proceed with the
installation.
Caution
!
1) Place the installation template
(outline shown on the next page)
included in the package on the
desired installation surface.
2) Drill holes in correct positions
based on the template paper, and
insert anchor blocks into the holes.
3) Make sure the necessary cables
including a LAN cable and a power
cable are properly connected to the
camera either thru the ceiling or thru
the groove around the mounting
plate.
4) Place the camera body and match
the alignment holes with the
corresponding anchor blocks and hold
against the mounting surface.
5) Tighten the anchor blocks with
screws.
6) Adjust the angle of the camera.
Refer to 4.2.Adjusting the angle of
the camera for more details.
7) Attach the dome cover on main
body and push it toward to the main
body till a “tick” sound is heard.
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 9
Installation Template
(Unit: mm)
Installation template’s image size scale in this installation guide is
not 1:1.
The correct-size template design paper can be found inside the
package separately.
Caution
!
Installation template
3202 V1.0
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 10
4.2. Adjusting the angle of the camera
Adjust the lens to the desired position by manually moving its upper lens shell,
reinforced body or horizontal platform in the following directions.
Refrain from continuously rotating the camera gimbal with
excessive force to a single direction as it is attached with a cable
inside the dome.
Caution
!
B. To pan, rotate the lower
body of the camera gimbal.
C. To tilt, tilt the lens by
vertically adjusting the camera
gimbal.
A. To adjust lens position,
rotate the camera gimbal.
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 11
4.3. Setting the Image Attribute
Through the camera’s webpage, users can configure image settings. The menu
of image attribute is available under Video Appearance menu in Setup > Video &
Audio > Camera. The following features can be adjusted: Brightness, Contrast,
Saturation, Sharpness and Orientation
For more detailed information, refer to the provided RIVA Web Interface Manual
Full HD Line”.
All Manual’s and Installation Guides can downloaded from www.rivatech.de
homepage.
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 12
4.4. Adjusting lens focus
The lens focus is pre-adjusted, best at 3m distance, when the
camera is manufactured. It is recommended not to adjust the lens
focus unless it has to.
Note
i
Set Ring
Lens
1) Remove the dome cover with the opener
included in the package.
2) *Rotate the set ring counterclockwise will
allow users to adjust the focus of the lens.
3) Adjust the focus of the lens by rotating
the lens. After the setting, tighten up the set
ring by turning it clockwise.
4) Once the lens focus is well-adjusted,
place the dome cover on the camera body
and gently push the dome cover until the
cover interlock with the camera body.
Opener
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 13
5. CONNECTIONS
DO
DI
Out
In
Com
Com
DO
DI
Out
In
Com
Com
In
Com
Out
Com
DI
DO
DO
DO
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 14
1 Sensor (DI) connection
Sensor (DI) can be connected to either a voltage type sensor or a relay type
sensor like the following figures. Settings can be done through the camera's
webpage.
Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA
Do not exceed the maximum input voltage or relay rate.
2 Alarm (DO) connection
Only the relay type is supported.
Relay Rating: Max 24VDC 50mA
Do not exceed the maximum relay rating.
Caution
!
Caution
!
DO
COM
Relay Type
Device
Internal
+3.3V
DI
COM
DI
COM
+
-
Relay Type
Voltage Type
+
-
Output of
Sensor
Output of
Sensor
Internal
Internal
+
-
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 15
3 LAN Connection
This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet
cable (RJ45) to connect the device to a hub or a router in the network. Refer to
Appendix (B). Power over Ethernet
” for more details.
4 Power Connection
The camera can be powered from either 12VDC or PoE. If the camera is
powered via PoE, refer to
Appendix (B). Power over Ethernet
for more details.
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 16
6. CONFIGURATION
6.1. Set up network environment
The default IP address of the device is 192.168.XXX.XXX. Users can identify the
IP address of the device from converting the MAC address’s hexadecimal numbers,
which is attached to the device. Be sure that the device and PC are on a same
area network before running the installation.
IP address : 192.168.xxx.xxx
Subnet mask: 255.255.0.0
6.1.1. Generic IP Environment
In case of generic private network environment where IP address
192.168.XXX.XXX are used, users may view the live streaming images on a web
page using the device’s default IP address:
1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-
Decimal Conversion Chart at the end of the manual.
(The MAC address of the device is attached on the side or bottom of the
device.)
2. Start the Microsoft® Internet Explorer web browser and enter the address of
the device.
3. Web streaming and device configurations are supported through ActiveX
program. When the ActiveX installation window appears, authorize and install
the ActiveX.
MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177
Convert the last two sets of hexadecimal numbers to decimal numbers.
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 17
6.1.2. Custom IP Environment
IPAdminTool is a management tool, which automatically scans all of the network
products for users to perform administrative tasks, which includes network
configurations, firmware update, device reboot, and device organizations.
IPAdminTool and the manual can download from www.rivatech.de homepage.
To modify the device’s default IP address for customized network area;
1. Find the device from the IPAdminTool’s list and highlight the device’s name.
2. Right-click the mouse and select IP Address; IP Setup window appears.
3. In the IP Setup’s window, information under Local Network information
displays the user/PC’s network area information. Those information need to
be incorporated to the IP Address, Subnet Mask, Gateway, and DNS boxes,
except the last 2 sets of IP Address, which are to be the unique numbers for
the device. Refer to the image above for the setting
4. Click Setup to complete the modification.
PC environment Info
Give new unique IP
address in last two sets
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 18
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 19
6.2. View video on web page
Type the proper IP address to view the live streaming images through a web
browser.
The default username and password is root / pass.
6.2.1. ActiveX Installation
1. When the browser asks to install the AxUMF software, click Install to
proceed.
2. When Setup installation pop-up window appears, click Install to proceed with
rest of installations.
Depending on system OS and Internet Explorer version, installation
experience may differ from one another. Figures described above are
from Windows 7, Internet Explorer 9 environment.
Note
i
HD Series RC3202HD-6111(W) Installation Guide
09-2013-A www.rivatech.de 20
Caution
!
6.2.2. View video using IPAdmin tool
IPAdminTool and the manual can download from www.rivatech.de homepage.
IPAdminTool automatically searches all activated network encoders and IP
cameras and shows the product name, IP address, MAC address and etc.
1. From the IPAdminTool’s product list, select the device by highlighting it.
2. Right-click the mouse and select Web View.
3. . The system’s default web browser opens the device’s address.
Whether directly accessing the streaming video through typing IP
address on a web page or taking steps through IPAdminTool, the
ActiveX is needed to be installed for the Microsoft® Internet
Explorer to have the complete configuration privileges.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Riva RC3202HD-6211(W) Instrukcja instalacji

Kategoria
Kamery ochrony
Typ
Instrukcja instalacji
Ten podręcznik jest również odpowiedni dla

w innych językach