Samsung SCC-B5313BP Instrukcja obsługi

User’s Guide

SCC-B531x(B)

Digital Color Dome Camera

ENG

RUS

POL

AB68-00647E(00)Eng.indd 1 2007-05-14 ｿﾀﾈﾄ 4:46:24

2

3

This symbol indicates high voltage

is present inside. It is dangerous to

make any kind of contact with any

inside part of this product.

This symbol alerts you that important

literature concerning operation and

maintenance has been included with

this product.

To prevent damage which may result in ﬁre

or electric shock hazard, do not expose this

appliance to rain or moisture.

WARNING

1. Be sure to use only the standard adapter

that is speciﬁed in the speciﬁcation

sheet. Using any other adapter could

cause ﬁre, electrical shock, or damage

to the product

2. Incorrectly connecting the power

supply or replacing battery may cause

explosion, ﬁre, electric shock, or damage

to the product.

3.

Do not connect multiple cameras to a single

adapter. Exceeding the capacity may cause

abnormal heat generation or ﬁre.

4. Securely plug the power cord into the

power receptacle. Insecure connection

may cause ﬁre.

5. When installing the camera, fasten it

securely and ﬁrmly. A falling camera may

cause personal injury.

6.

Do not place conductive objects (e.g.

screwdrivers, coins, metal things, etc.) or

containers ﬁlled with water on top of the

camera. Doing so may cause personal injury

due to ﬁre, electric shock, or falling objects.

7. Do not install the unit in humid, dusty, or

sooty locations. Doing so may cause ﬁre

or electric shock.

8. If any unusual smells or smoke come

from the unit, stop using the product. In

such case, immediately disconnect the

power source and contact the service

center. Continued use in such a condition

may cause ﬁre or electric shock.

Safety Precautions

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE REAR

COVER. NO USER SERVICEABLE PARTS

INSIDE. REFER TO QUALIFIED SERVICE

PERSONNEL.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

AB68-00647E(00)Eng.indd 2 2007-05-14 ｿﾀﾈﾄ 4:46:24

2

ENG

3

9. If this product fails to operate normally,

contact the nearest service center. Never

disassemble or modify this product

in any way. (SAMSUNG is not liable

for problems caused by unauthorized

modiﬁcations or attempted repair.)

10. When cleaning, do not spray water

directly onto parts of the product. Doing

so may cause ﬁre or electric shock.

CAUTION

1. Do not drop objects on the product or

apply strong shock to it. Keep away from

a location subject to excessive vibration

or magnetic interference.

2. Do not install in a location subject to

high temperature (over 122°F), low

temperature (below 14°F), or high

humidity. Doing so may cause ﬁre or

electric shock.

3. If you want to relocate the already

installed product, be sure to turn off the

power and then move or reinstall it.

4. Remove the power plug from the

outlet when then there is a lightning.

Neglecting to do so may cause ﬁre or

damage to the product.

5. Keep out of direct sunlight and heat

radiation sources. It may cause ﬁre.

6. Install it in a place with good ventilation.

7. Avoid aiming the camera directly towards

extremely bright objects such as sun,

as this may damage the CCD image

sensor.

8. Apparatus shall not be exposed to

dripping or splashing and no objects

ﬁlled with liquids, such as vases, shall be

placed on the apparatus.

9. The Mains plug is used as a disconnect

device and shall stay readily operable at

any time.

FCC Statement

This device complies with part 15 of the FCC

Rules. Operation is subject to the following

two conditions:

1) This device may not cause harmful

interference, and

2) This device must accept any interference

received including interference that may

cause undesired operation.

Note

This equipment has been tested and found to

comply with the limits for a Class A digital device,

pursuant to part 15 of FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference when the equipment

is operated in a commercial environment. This

equipment generates, uses, and can radiate

radio frequency energy and, if not installed

and used in accordance with the instruction

manual, may cause harmful interference to radio

communications. Operation of this equipment

in a residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his own

expense.

AB68-00647E(00)Eng.indd 3 2007-05-14 ｿﾀﾈﾄ 4:46:24

4

5

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.

Install in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources

such as radiators, heat registers, or

other apparatus (including ampliﬁers)

that produce heat.

9. Do not defeat the safety purpose of

the polarized or grounding-type plug.

A polarized plug has two blades with

one wider than the other. A grounding

type plug has two blades and a third

grounding prong. The wide blade or the

third prong is provided for your safety.

If the provided plug does not ﬁt into

your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being

walked on or pinched particularly at

plugs, convenience receptacles, and the

point where they exit from the apparatus.

11. Only use attachments/accessories

speciﬁed by the manufacturer.

12. Use only with cart, stand, tripod, bracket,

or table speciﬁed by the manufacturer, or

sold with the apparatus.

13. Unplug this apparatus. When a cart is

used, use caution when moving the

cart/apparatus combination to avoid

injury from tip-over.

14. Refer all servicing to qualiﬁed service

personnel. Servicing is required when

the apparatus has been damaged in any

way, such as power-supply cord or plug

is damaged, liquid has been spilled or

objects have fallen into the apparatus,

the apparatus has been exposed to rain

or moisture, does not operate normally,

or been dropped.

AB68-00647E(00)Eng.indd 4 2007-05-14 ｿﾀﾈﾄ 4:46:24

4

ENG

5

Overview ..................................................................................... 6

About this guide ............................................................................6

Product overview ...........................................................................6

Main features .................................................................................6

Components ...................................................................................6

Checking components in the package .......................................6

Components of your camera ......................................................7

Installation ................................................................................. 8

Setting switches ............................................................................8

Setting function switches ............................................................8

Connecting cables and setting switches ..................................10

Installing camera ......................................................................... 11

Before installation .....................................................................11

Installation procedure ............................................................... 11

Adjusting the camera direction ..................................................12

Appendix A: Speciﬁcations for NTSC Standard ........... 13

Appendix B: Speciﬁcations for PAL Standard ..............

15

Contents

AB68-00647E(00)Eng.indd 5 2007-05-14 ｿﾀﾈﾄ 4:46:25

6

7

❚

About this guide

This user guide includes basic instructions for

the product. It is recommended that all users

read this guide before use.

This guide is divided as follows:



Chapter 1, “Overview,” introduces the user guide

and product related information. (This chapter)



Chapter 2, “Installation,” explains how to set and

install the product.



Appendix, “Speciﬁcations,” provides the

speciﬁcations of the product.

❚

Product overview

This is the high resolution dome camera

equipped with a ﬁxed focal lens, which has

no dynamic delay when implementing motion

pictures, and provides the features such as

digital noise reduction (DNR) by real-time

CCD defect compensation, low speed shutter

(LSS: Auto x128) to implement clear picture

quality, Day/Night color compensation, and

the like.

❚

Main features



Power: DC 12V/AC 24V



Special functions



Line lock (LL) control



Auto white balancing



Horizontal/vertical image reversing



Auto gain control



Low shutter speed control



Backlight compensation control



Automatic switching between color and black

& white modes



Digital noise reduction (DNR)



Dynamic CCD defect compensation

❚

Components

Checking components in the package

Please check your camera and accessories

are included in the package. Those

components are as shown below:

Camera Test Monitor Cable

Tab screw User’s Guide

Note

The test monitor cable is used to test the camera

by connecting to a portable display. If you really

want to connect the camera to a monitoring

display, use the BNC cable.

Overview

AB68-00647E(00)Eng.indd 6 2007-05-14 ｿﾀﾈﾄ 4:46:25

6

ENG

7

Components of your camera

Your camera has the following components:

1. Cover dome

: Covers the lens and main

body to protect them.

2. Main body

: Includes a lens, a switch

board, a PCB board, screws, and such.

3. Locker

: Used to open or close the Cover

dome. To open the cover dome, press the

locker.

4. Tilt ﬁxing screw: Using this screw, the

slope of the lens can be adjusted and

ﬁxed.

5. Switch board

: Includes two kinds

of control switches such as function

switches and phase-control switches.

The board has eight function switches in

the middle and two phase-control buttons

on each side of the function switch area.

6. Lock releaser

: Push it outward and

rotate the main body in UNLOCK

direction when you want to remove the

mount bracket from the main body.

7. Mount bracket

: Used as a ceiling or wall

ﬁxture. It is ﬁxed using three long tab

screws provided in the package.

8. Ceiling mount opener

: Remove it for

line connection to the ceiling when it is

installed on the ceiling.

1

Lens

2

3

4

5

6

7

8

AB68-00647E(00)Eng.indd 7 2007-05-14 ｿﾀﾈﾄ 4:46:28

8

9

❚

Setting switches

Setting function switches

To set the available functions on your camera, adjust eight switches as shown below:

Installation

No Name Brief description

1 LL Line lock ON/OFF

2 LSS Sens-up or Low speed shutter ON/OFF

3 H-REV Horizontal reverse ON/OFF

4 V-REV Vertical reverse ON/OFF

5 BLC Backlight compensation ON/OFF

6 AGC Auto gain control ON/OFF

7 D/N

Automatic switching between color and

black & white ON/OFF

8 AWB Automatic white balance ON/OFF

DEC

INC

8

7

6

5

4

3

2

1

1. Switch 1 (LL): When this switch is set to OFF, the camera operates in the internal

synchronization mode, while when it is set to ON, the camera operates in the line lock mode.

In the internal synchronization mode, the camera always uses an inside crystal oscillator for

synchronization. However if multiple cameras are connected to a sequential switcher, picture

rolling or ﬂickering may occur when switching from one camera to another. In this case, you

can set this switch to ON to solve this problem.

The line lock mode allows the camera to use the phase of the AC power as the

synchronization reference. In this mode, you can use the phase control buttons(INC/DEC).

Note

When you are using the DC 12V power, set this switch to OFF. The line lock feature will not normally

operate even when the switch is set to ON.

Set the LL switch to ON while the AC power is connected. If any picture roll happens, you have

to adjust the phase using the phase-control buttons. Press the INC or DEC button to increase or

decrease the phase by one degree.

AB68-00647E(00)Eng.indd 8 2007-05-14 ｿﾀﾈﾄ 4:46:32

8

ENG

9

2. Switch 2 (LSS): This sens-up mode accumulates the image ﬁelds in memory to reduce

noise but increase the brightness and contrast rate. When this switch is set to ON, the

camera automatically switches to a maximum of 128 times of image acquisition speed to

implement a clear picture for darker image.

3. Switch 3 (H-REV): When this switch is set to ON, the camera image is reversed horizontally.

If you want to monitor your site using a mirror, you can use this feature to see the right

image.

4. Switch 4 (V-REV)

: When this switch is set to ON, the camera image is reversed vertically.

If your camera reluctantly displays the vertically reversed image, you can use this feature to

see the right image.

5. Switch 5 (BLC)

: When this switch is set to ON, you can view a clear image even though the

camera faces any excessive light such as sunlight and ﬂuorescent light. When it is set to

OFF, the subject with excessive light is not clearly shown.

6. Switch 6 (AGC)

: When this switch is set to ON, the camera automatically increase the

sensitivity by amplifying the video signal when the strength of the signal falls below a given

value. When any dark images are expected, use this feature.

7. Switch 7 (D/N)

: When this switch is set to ON, the camera automatically switches between

color and B&W according to the brightness of the vicinity.

8. Switch 8 (AWB): This switch adjusts white balancing. When this switch is set to

ON, this

camera operates in ATW mode, and in case of

OFF, this camera operates in AWC mode.



ATW (Auto Tracking White Balance): The color temperature is automatically adjusted according to the

environmental change. (Approx. 2000°K to 11,000°K)



AWC (Auto White Balance Control): It stores the color temperature just when the switch is changed to

OFF. Accordingly color temperatures are adjusted by the stored value.

AB68-00647E(00)Eng.indd 9 2007-05-14 ｿﾀﾈﾄ 4:46:33

10

11

❚

Connecting cables and setting switches

To connect cables

1. Connect the BNC cable

to the Video connector

attached on your camera.

2. Connect the BNC cable

to the Video Input on a

monitor.

3. Connect the power

adapter to the Power

connector attached on

your camera. When the

monitor is turned on, the

camera image appears.

To check the camera view and set the switches

1. Remove the Cover dome. For more details about the removing procedures, see “Installation

procedure,” in the Installing camera section on the next page.

2. Adjust the function of your camera using the Switch board while you are viewing the image

on the screen.

BNC Cable

Monitor

AB68-00647E(00)Eng.indd 10 2007-05-14 ｿﾀﾈﾄ 4:46:33

10

ENG

11

❚

Installing camera

Before installation

Before installing your camera, you have to read the following cautions:



You have to check whether the location (ceiling or wall) can bear ﬁve times the weight of your camera.



Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise it

may cause a breakdown or ﬁre.



When installing your camera, don’t allow any person to approach the installation site. If you have any

valuable things under the place, move them away.

Installation procedure

To install your camera

1. Press the Locker button on the bottom

of your camera and remove the Cover

dome from the Main body using the

other hand. The Main body will be

exposed to you.

2. As shown in the picture, push the Lock

releaser outward and rotate the Main

body in the UNLOCK direction to remove

the Mount bracket. If it is not easily

done, rotate the Mount bracket in the

LOCK direction while holding small holes

on the Mount bracket.

3. Fix the Mount bracket to the location

(ceiling or wall) with supplied three

screws.

Note

The CAMERA FRONT sign on the Mount

bracket should face the camera monitoring

area.

1

Ceiling mount

opener

2

3

AB68-00647E(00)Eng.indd 11 2007-05-14 ｿﾀﾈﾄ 4:46:34

12

13

4. When you install the Mount bracket on the ceiling, remove the Ceiling mount opener by

pressing it hard to connect the line attached on your camera through the hole in the ceiling.

Otherwise, you can use the empty space opposite to the CAMERA FRONT sign for line

connection.

5. Now attach the Main body to the Mount bracket by rotating it in the LOCK direction after

aligning the Lock releaser on the Main body with the wide groove around the CAMERA

FRONT inlay.

6. Adjust the camera direction. For more details on the direction control, see “Adjusting the

camera direction,” on the same page.

7. Finally attach the Cover dome to the Main body by pressing it until a “click” sound is heard

after aligning the wide groove at the lower part of the Cover dome with the Locker on the

Main body.

❚

Adjusting the camera direction

When the camera is ﬁxed on the ceiling, you can adjust

the camera viewing angle. You can rotate your camera

leftward or rightward (Panning), and can change the

slope of your camera upward or downward (Tilting).

In case of panning, the rotation limit of your camera

is set to 340 degree (220 degree clockwise and 120

degree counterclockwise). The rotation is stopped by the

Stopper inside of the camera. For panning control, ﬁrst

unfasten two screws located on the bottom and rotate in

the direction you want, and then fasten them to ﬁx the

camera. When both ﬁxing screws cannot be tightened,

change the location of screws. When inevitable, just

tightening one screw is alright.

In case of tilting, you can change the slope of your camera from zero to 90 degree. When

the slope angle is under 23 degree, you can encounter a partial image hide problem. To ﬁx

the location after adjusting the tilting angle, use the Tilt ﬁxing screws.

To adjust the focus of your camera, rotate the ﬁxed lens for clear image. When you install

the camera on the inclined ceiling or wall, you can rotate the camera lens to see a correct

direction image.

Panning

Tilting

Lens rotation

AB68-00647E(00)Eng.indd 12 2007-05-14 ｿﾀﾈﾄ 4:46:35

12

ENG

13

SCC-B531X

AB68-00647E(00)Eng.indd 13 2007-05-14 ｿﾀﾈﾄ 4:46:36

14

15

Appendix A: Speciﬁcations for NTSC Standard

Item Details

Product type CCTV color dome camera

Power input AC 24V ± 10% (60Hz ± 0.3 Hz), DC 12V +10%/-5%

Broadcast type NTSC Standard color system (525 Lines, 60 Fields)

Power consumption Approx. 1.6W

Image device 1/3 inch IT Type Super-HAD CCD

Pixels

SCC-B5311N, B5313N, B5315N

SCC-B5310N

Total: 811(H) x 508(V), 410,000 pixels

Effective: 768(H) x 494(V), 380,000 pixels

Total: 537(H) x 505(V), 270,000 pixels

Effective: 510(H) x 492(V), 250,000 pixels

Scanning mode 525 Lines, 2:1 Interlace

Scanning line frequency

Horizontal: 15.734Hz(INT)/15.750Hz(LL)

Vertical

: 59.94Hz(INT)/60Hz(LL)

Synchronization mode INT/Line Lock (Adjusting the phase using INC/DEC button)

Horizontal resolution

SCC-B5311N, B5313N, B5315N

SCC-B5310N

540 TV Lines 330 TV Lines

Min. object illumination

SCC-B5311N, B5313N, B5315N

SCC-B5310N

F2.0

Sens-up Off

50IRE 1Lux 0.6Lux

30IRE 0.6Lux 0.4Lux

15IRE 0.3Lux 0.2Lux

Sens-up x128

50IRE 0.008Lux 0.005Lux

30IRE 0.005Lux 0.003Lux

15IRE 0.002Lux 0.001Lux

Signal output

COMPOSITE Video(1

.

0 Vp-p, 75ohm, BNC), Test Monitor OUT(1

.

0 Vp-p, 75ohm, Harness cable)

Lens

Focal length Zone Limit of viewing angle Model

3.0mm

Horizontal

Vertical

92°

72°

SCC-B5313N

3.8mm

Horizontal

Vertical

71°

53°

SCC-B5310N,

B5311N

8.0mm

Horizontal

Vertical

33.6°

25.3°

SCC-B5315N

PAN function

Range: 0 to 340° (220 degree clockwise and 120 degree counterclockwise)

TILT function Range: 0 to 90°

AB68-00647E(00)Eng.indd 14 2007-05-14 ｿﾀﾈﾄ 4:46:38

14

ENG

15

Item Details

Controls

Line Lock (LL)

Sens-up; Low Speed Shutter(LSS)

Horizontal Reverse (H-REV)

Vertical Reverse (V-REV)

Backlight compensation (BLC)

Auto gain control (AGC)

Switching between color and B&W by day and night change (D/N)

Automatic white balancing (AWB)

Digital noise reduction (DNR)

Dynamic CCD defect compensation

Product color SCC-B531xN : White / SCC-B531xBN : Black

Operation temperature -10°C to +50°C

Operation humidity Up to 90%

Size 102(φ) x 78(H)mm

Weight

190g

AB68-00647E(00)Eng.indd 15 2007-05-14 ｿﾀﾈﾄ 4:46:38

16

17

Appendix B: Speciﬁcations for PAL Standard

Item Details

Product type CCTV color dome camera

Power input AC 24V ± 10% (50Hz ± 0.3 Hz), DC 12V +10%/-5%

Broadcast type PAL Standard color system (625 Lines, 50 Fields)

Power consumption Approx. 1.6W

Image device 1/3 inch IT Type Super-HAD CCD

Pixels

SCC-B5311P, B5313P, B5315P

SCC-B5310P

Total

: 795(H) x 596(V), 470,000 pixels

Effective: 752(H) x 582(V), 440,000 pixels

Total: 537(H) x 597(V), 320,000 pixels

Effective: 500(H) x 582(V), 290,000 pixels

Scanning mode 625 Lines, 2:1 Interlace

Scanning line frequency

Horizontal: 15.625Hz(INT)/15.625Hz(LL)

Vertical

: 50Hz(INT)/50Hz(LL)

Synchronization mode INT/Line Lock (Adjusting the phase using INC/DEC button)

Horizontal resolution

SCC-B5311P, B5313P, B5315P

SCC-B5310P

540 TV Lines 330 TV Lines

Min. object illumination

SCC-B5311P, B5313P, B5315P

SCC-B5310P

F2.0

Sens-up Off

50IRE 1Lux 0.6Lux

30IRE 0.6Lux 0.4Lux

15IRE 0.3Lux 0.2Lux

Sens-up x128

50IRE 0.008Lux 0.005Lux

30IRE 0.005Lux 0.003Lux

15IRE 0.002Lux 0.001Lux

Signal output

COMPOSITE Video(1

.

0 Vp-p, 75ohm, BNC), Test Monitor OUT(1

.

0 Vp-p, 75ohm, Harness cable)

Lens

Focal length Zone Limit of viewing angle Model

3.0mm

Horizontal

Vertical

92°

72°

SCC-B5313P

3.8mm

Horizontal

Vertical

71°

53°

SCC-B5310P,

B5311P

8.0mm

Horizontal

Vertical

33.6°

25.3°

SCC-B5315P

PAN function

Range: 0 to 340° (220 degree clockwise and 120 degree counterclockwise)

TILT function

Range: 0 to 90°

AB68-00647E(00)Eng.indd 16 2007-05-14 ｿﾀﾈﾄ 4:46:38

16

ENG

17

Item Details

Controls

Line Lock (LL)

Sens-up; Low Speed Shutter(LSS)

Horizontal Reverse (H-REV)

Vertical Reverse (V-REV)

Backlight compensation (BLC)

Auto gain control (AGC)

Switching between color and B&W by day and night change (D/N)

Automatic white balancing (AWB)

Digital noise reduction (DNR)

Dynamic CCD defect compensation

Product color SCC-B531xP : White / SCC-B531xBP : Black

Operation temperature -10°C to +50°C

Operation humidity Up to 90%

Size 102(φ) x 78(H)mm

Weight

190g

AB68-00647E(00)Eng.indd 17 2007-05-14 ｿﾀﾈﾄ 4:46:38

AB68-00647E(00)Eng.indd 18 2007-05-14 ｿﾀﾈﾄ 4:46:38

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate

collection systems)

This marking shown on the product or its literature, indicates that it should

not be disposed with other household wastes at the end of its working life. To

prevent possible harm to the environment or human health from uncontrolled

waste disposal, please separate this from other types of wastes and recycle it

responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this

product, or their local government ofﬁce, for details of where and how they can

take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions

of the purchase contract. This product should not be mixed with other commercial

wastes for disposal.

AB68-00647E(00)Eng.indd 19 2007-05-14 ｿﾀﾈﾄ 4:46:38

AB68-00647E(00)Eng.indd 20 2007-05-14 ｿﾀﾈﾄ 4:46:38

Strona jest ładowana ...

Samsung SCC-B5313BP Instrukcja obsługi

Samsung SCC-B5313BP Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty