Vermeiren V300 DL Instrukcja obsługi

VERMEIREN

I N S T R U C T I O N M A N U A L

M O D E D ’ E M P L O I

G E B R U I K S A A N W I J Z I N G

G E B R A U C H S A N W E I S U N G

I S T R U Z I O N I P E R L ' U S O

MANU A L D E I N S T R U C C I ON E S

I N S T R U K C J A O B S Ł U G I

N Á V O D K O B S L U Z E

V300 DL

All r

ights reserved, including translation.

No part of this manual may be reproduced in any form

what so ever (print, photocopy, microfilm or any other

process) without written permission of the publisher, or

processed, duplicated or distributed by using electronic

systems.

Aucune partie de ce manuel ne peut être reproduite,

sous quelque forme que ce soit (imprimée, photocopie,

microfilm ou tout autre procédé) sans l'autorisation écrite

du publicateur, ni traitée, dupliquée ou distribuée à l'aide

de systèmes électroniques.

Alle rechten, inclusief vertaling, voorbehouden.

Niets uit deze handleiding mag geheel of gedeeltelijk in

enige vorm (druk, fotokopie, microfilm of ieder ander

procedé) zonder de schriftelijke toelating van de uitgever

worden gereproduceerd of met behulp van elektronische

systemen worden verwerkt, gekopieerd of verspreid.

Alle Rechte, auch an der Übersetzung, vorbehalten.

Kein Teil der Gebrauchsanweisung darf in irgendeiner

Form (Druck, Fotokopie, Mikrofilm oder einem anderen

Verfahren) ohne schriftliche Genehmigung des

Herausgebers reproduziert oder unter Verwendung

elektronischer Systeme verarbeitet, vervielfältigt oder

verbreitet werden.

Il presente manuale non può essere riprodotto, neppure

parzialmente, con alcun mezzo (stampa, fotocopia,

microfilm o altro procedimento) senza l’autorizzazione

scritta della casa produttrice, né elaborato, duplicato o

distribuito con l’ausilio di sistemi elettronici.

traducción.

Se prohíbe la reproducción total o parcial del presente

manual de cualquier forma (impresión, fotocopia,

microfilm o cualquier otro procedimiento), así como la

edición, copia o distribución empleando sistemas

electrónicos, sin el permiso escrito del editor.

Wszelkie prawa zastrzeżone, łącznie z

tłumaczeniem.

Żadna część niniejszej instrukcji nie może być

powielana w jakiejkolwiek formie (drukowanej, fotokopii,

mikrofilmu ani innej) bez pisemnej zgody wydawcy, nie

może być również przetwarzana, kopiowana ani

rozprowadzana za pomocą systemów elektronicznych.

Všechna práva vyhrazena, včetně překladu.

Šíření jakékoliv části tohoto katalogu jakýmkoliv

způsobem (tisk, kopie, mikrofilm nebo jiný způsob) bez

písemného souhlasu vydavatele, nebo zpracování,

duplikace či distribuce prostřednictvím elektronických

systémů je zakázáno.

EN

Instructions for specialist dealer

This instruction manual is part and parcel

of the product and must accompany every

product sold.

Version: A, 2016-03

FR

Instructions pour les distributeurs

Ce manuel d'instructions fait partie du

produit et doit accompagner chaque

produit vendu.

Version : A, 2016-03

NL

Instructies voor de vakhandelaar

Deze handleiding is deel van het product

en dient bij iedere product te worden

geleverd.

Versie: A, 2016-03

DE

Hinweise für den Fachhändler

Diese Gebrauchsanweisung ist Bestand-

teil des Produkts und ist bei jeder

Produkts auszuhändigen.

Version: A, 2016-03

IT

Istruzioni per il rivenditore

Il presente Manuale di istruzioni è parte

integrante del prodotto e deve essere

fornito assieme alla prodotto.

Versione: A, 2016-03

ES

Instrucciones destinadas a los distri-

buidores especializados

El presente manual de instrucciones es

parte integrante del producto y se debe

adjuntar a todas las producto que se

vendan.

Versión: A, 2016-03

PL

Instrukcje dla wyspecjalizowanego

sprzedawcy

Niniejsza instrukcja obsługi jest

nieodłączną częścią produktu i musi być

dołączona do każdego sprzedawanego

produktu.

Wersja: A, 2016-03

CS

Pokyny pro specializovaného prodejce

Tento návod k obsluze je součástí

dodávky a musí být součástí každého

prodaného produktu.

Verze: A, 2019-06

Multi version: B, 2019-06

V300DL

2016-03

Page1

Contents

Preface ................................................................................................. 2

1 Product description ................................................................. 3

1.1 Intended use ................................................................................................................. 3

1.2 Technical specifications .............................................................................................. 4

1.3 Components ................................................................................................................. 5

1.4 Accessories .................................................................................................................. 6

1.5 Location identification plate ........................................................................................ 6

1.6 Explanation of symbols ............................................................................................... 6

1.8 Safety rules .................................................................................................................. 7 

2 Use ............................................................................................. 7

2.1 Carrying the wheelchair .............................................................................................. 7

2.2 Mounting the rear wheels ............................................................................................ 8

2.3 Unfolding the wheelchair ............................................................................................ 8

2.4 Mounting or removing of stabilisator .......................................................................... 8

2.5 Mounting or removing of the footrests ....................................................................... 9

2.6 Operating the brakes .................................................................................................... 9

2.7 Mounting or removing of armrests ............................................................................ 10

2.8 Adjusting the armrest ................................................................................................ 11

2.9 Adjusting anti-tipping (only mounted to the right side) ............................................ 11

2.10 Adjusting height hand grips ...................................................................................... 12

2.11 Transfer in and out the wheelchair ............................................................................ 12

2.12 Correct position in the wheelchair ............................................................................ 12

2.13 Riding the wheelchair ................................................................................................ 12

2.14 Moving on slopes ...................................................................................................... 13

2.15 Negotiating steps or curbs ......................................................................................... 13

2.16 Fold up the wheelchair .............................................................................................. 15

2.17 Taking off the rear wheels ......................................................................................... 15

2.18 Transport in the car .................................................................................................... 15

2.19 Use of the wheelchair as seat in a motor vehicle ...................................................... 16

3 Installation and adjustment .................................................. 18

3.1 Tools .......................................................................................................................... 18

3.2 Manner of delivery .................................................................................................... 18

3.3 Adjusting the seat height and seat angle ................................................................... 18

3.4 Adjusting the seat depth ............................................................................................ 21

3.5 Adjust the brakes ....................................................................................................... 22

3.6 Adjusting of the footrests .......................................................................................... 22

3.7 Adjusting the depth arm pad ..................................................................................... 23

3.8 Adjusting the stability and the maneuverability ........................................................ 24

4 Maintenance ........................................................................... 24

V300DL

2016-03

Page2

Preface

First of all we want to thank you for putting your trust in us by selecting one of our

wheelchairs.

The Vermeiren wheelchairs are the result of many years of research and experience. During

the development, special attention was given to the ease of use and the serviceability of the

wheelchair.

The expected lifetime for your wheelchair is strongly influenced by the care and maintenance

of the wheelchair.

This manual will help you get acquainted with the operation of your wheelchair.

Following the user instructions and the maintenance instructions are an essential part of the

guarantee.

This manual reflects the latest product developments. Vermeiren has the right to introduce

changes without the obligation to adapt or replace previously delivered models.

For any further questions, please consult your specialist dealer.

V300DL

2016-03

Page3

1 Product description

1.1 Intended use

The wheelchair is intended for people with walking difficulties or no walking abilities.

The wheelchair is designed to transport 1 person.

The wheelchair is suited for indoor and outdoor use.

The user can propel the wheelchair by himself or have the wheelchair pushed by an

attendant.

The different types of fittings and accessories, and the modular construction allow full use by

persons disabled by:

 paralysis

 loss of limbs (leg amputation)

 limb defects or deformations

 stiff or damaged joints

 heart insuffiencies and poor blood circulation

 balance disturbances

 cachexia (decrease in muscle)

 and also for aged persons.

When providing for individual requirements:

 body size and weight (max. 130 kg)

 physical and psychological condition

 residential circumstances

 environment

should be taken into consideration.

Your wheelchair should only be used on surfaces where all four wheels are touching the

ground and where there is sufficient contact to propel the wheels equally.

You should practice for use on uneven surfaces (cobblestones, etc.), slopes, curves and to

get past obstacles (curbs, etc.).

The wheelchair should not be used as a ladder, nor is it a transport for heavy or hot objects.

When used on mats, carpeted floors or loose floor coverings, the floor covering can get

damaged.

Use only Vermeiren approved accessories.

The manufacturer is not liable for damage caused by the lack of or improper service or as a

result of not following instructions from this manual.

Compliance with the user and maintenance instructions are an essential part of the

guarantee conditions.

V300DL

2016-03

Page4

1.2 Technical specifications

Technical terms below are valid for the wheelchair in standard settings. If other footrests /

armrests or other accessories are used, the tabulated values will change.

Make

V

ermeiren

Address

V

ermeirenplein 1/15, B-2920 Kalmthout

Type Manual wheelchai

r

Model

V

300DL

Maximum occupant mass 130 kg

Description Min. Max.

Overall length with footrest 1000 mm

(minimum length footrest)

1040 mm

(maximum length footrest)

Overall height (depends on seat

height - measured for seat height 500

mm)

890 mm

(minimum height hand grip)

990 mm

(maximum height hand grip)

Effective seat width 390 mm 420 mm 440 mm 460 mm 480 mm 500 mm

Overall width (depends on the seat

width)

600 mm 630 mm 650 mm 670 mm 690 mm 710 mm

Folded length without footrest 810 mm

Folded width 320 mm

Folded height 890 mm 990 mm

Total mass 18,80 kg (measured for seat width 460 mm)

Mass of heaviest part 11 kg

Masses of parts that can be

dismantled or removed

Footrests: 1,80 kg;

A

rmrests: 2,20 kg; Rear wheels: 3,80 kg

Static stability downhill 10° (in standard configuration)

Static stability uphill 7° (in standard configuration)

Static stability sideways 18° (in standard configuration)

Obstacle climbing 60 mm

Seat plane angle 0° 10°

Effective seat depth 440 mm 520 mm

Seat surface height at front edge

(measured on top of the cross tubes)

440 mm 530 mm

Thickness seat cushion 50 mm

Backrest angle 5°

Backrest height 460 mm

Distance between footrest and seat 420 mm

Angle between seat and leg footrest 105°

Angle between leg footrest and foot

plate

80° 100°

Distance between arm pad and seat

(without seat cushion)

195 mm 300 mm

Front location of arm pad structure 335 mm 455 mm

Handrim diameter 535 mm

Horizontal location of axle

(deflection)

1,27 mm 61,04 mm

Minimum turning radius 1500 mm

Diameter PU Rear wheels 22" 24"

Tyre pressure, rear (driving) wheels Max. 3.5 bar

V300DL

2016-03

Page5

Make

V

ermeiren

Address

V

ermeirenplein 1/15, B-2920 Kalmthout

Type Manual wheelchai

r

Model

V

300DL

Maximum occupant mass 130 kg

Diameter PU steering wheels 200 mm

Tyre pressure, steering wheels Max. 2.5 bar

Storage and use temperature + 5 °C + 41 °C

Storage and use humidity 30% 70%

We reserve the right to introduce technical changes. Measurement tolerance ± 15 mm / 1,5 kg / °

Table 1: Technical specifications

The wheelchair complies to the requirements set up in:

ISO 7176-8: Requirements and test methods for static, impact and fatigue strengths.

ISO 7176-16: Resistance to ignition of upholstered parts

1.3 Components

1 = Hand grips

2 = Stabilisator

3 = Arm pads

4 = Armrests

5 = Footrests

6 = Foot plates

7 = Brakes

8 = Steering wheels

(front wheels)

9 = Driving wheels (rear

wheels)

10 = Seat

11 = Seat cushion

12 = Backrest

13 = Tip cap

14 = Anti-tipping

15 = Cross

V300DL

2016-03

Page6

1.4 Accessories

The following accessories are available for the V300DL:

 Anterior pelvic belt (B20) for mounting on the tubes of the back

 Tables (B15A, B12)

 Crutch holder

1.5 Location identification plate

1.6 Explanation of symbols

Maximum mass

Indoor and outdoor use

Maximum Safe Slope

CE conformity

1 = Logo Vermeiren

2 = Taxi hooks

3 = Identification plate

4 = Name Vermeiren

Type designation

V300DL

2016-03

Page7

1.8 Safety rules

L

To prevent injury and/or damage to your wheelchair, make sure that no objects

and/or body parts are caught in the spokes of the driving wheels.

L The parking brakes should be applied before getting into and out of the wheelchair.

L When getting into and out of the wheelchair, do not stand on the foot plates. These

should be folded up beforehand, or the footrest should be swung completely outwards

out of the way.

L Investigate the effects of shifting the centre of gravity on the behavior of the wheelchair,

for example on up or down gradients, on laterally sloping ground, or when overcoming

obstacles. Obtain support from an attendant.

L If you want to pick up something (lying in front of, on the side, or to the rear of the

wheelchair), you should not lean too far out to avoid tipping over.

L When moving through doors, arches, etc. ensure that there is enough room at the sides

so that you do not get your hands or arms caught or crushed and that there is no

damage to the wheelchair.

L Only use your wheelchair according to regulations. For example, avoid uncontrolled

rolling against obstacles (steps, curbs, doorframes, etc) or dropping down from ledges.

The manufacturer cannot assume liability for damage caused by overloading, collision

or other improper use.

L Stairs may only be negotiated when aided by another person. If furnishings like drive-on,

ramps or lifts are available, use them.

L When moving on the public highway, you are subject to the rules of the road.

L When driving your wheelchair, you should not be under the influence of alcohol or

medicine as in the case of driving other vehicles. This also applies to indoor driving.

L When travelling outdoors, adapt your driving to weather and traffic conditions.

L To be better visible when driving in the dark, wear the brightest possible clothing or

clothes with reflectors, and check that the reflectors mounted on the sides and rear of

the wheelchair are clearly visible.

L Never exceed the maximum load of 130 kg.

2 Use

This chapter describes the everyday use. These instructions are for the user and the

specialist dealer.

The wheelchair is delivered fully assembled by your specialist dealer. The instructions

intended for the specialist dealer on how to set up the wheelchair are given in § 3.

2.1 Carrying the wheelchair

The best way to carry the wheelchair is to make use of the wheels and roll the wheelchair.

If this is not possible (e.g. when the rear wheels are taken off for transportation in a car),

firmly grasp the frame on the front and the hand grips. Do not use the foot or armrests or the

wheels to grasp the wheelchair.

V300DL

2016-03

Page8

2.2 Mounting the rear wheels

1. Take the rear wheel and push on button .

2. Keep the button pushed in and mount the rear

wheels axle till it stops.

3. Release the button.

4. Check that the wheels are secured.

2.3 Unfolding the wheelchair

L

CAUTION: Risk of clamping – Keep fingers away from moving parts of the

wheelchair.

1. Position yourself behind the wheelchair.

2. Use the hand grips to open the wheelchair as much as possible.

3. Position yourself at the front of the wheelchair.

4. Push both seating tubes down till they are fixed in their position.

5. Mount the stabilisator to the right hand grip (standing behind the wheelchair).

2.4 Mounting or removing of stabilisator

L

WARNING: Risk of injury - Make sure that star knobs Ⓐ are tightened.

L WARNING: Risk of injury - Always mount the stabilisator (→ to increase the

stability of the backrest).

The mounting of the stabilisator Ⓑ is done as follows:

1. Mount the stabilisator Ⓑ with the star knob Ⓐ in the left hand grip.

2. Swing the stabilisator Ⓑ to the right.

3. Mount hook Ⓒ over the right hand grip Ⓓ as shown on the drawing. Use holes  or  to

adjust the tension of the backrest.

To take off the stabilisator:

1. Loosen the star knob Ⓐ on the right hand grip.

2. Remove hook Ⓒ from the right hand grip Ⓓ.

V300DL

2016-03

Page9

2.5 Mounting or removing of the footrests

The mounting of the footrests is done as follows:

1. Hold the footrest sideways at the outside of the

wheelchairs frame and mount the tube hood



into the frame.

2. Swing the footrest inwards till it clicks in

position.

3. Swing the foot plate downwards.

To take off the footrests:

1. Pull lever

.

2. Swing the footrest to the outside of the

wheelchair till it comes loose from the guidance.

3. Pull the footrest from tube hood

.

2.6 Operating the brakes

L

WARNING: The brakes are not used to slow down the wheelchair during

movements – Use the brake only to prevent the wheelchair from unintended

movements.

L WARNING: Good operation of the brakes is influenced by wear and

contamination of the tires (water, oil, mud, …) – Check the condition of the tires

before each use.

L WARNING: The brakes are adjustable and can wear – Check the operation of the

brakes before each use.

To reduce the braking force

it is possible to extend the

brake lever (Fig B).

To apply the brakes (Fig A):

1. Push the brake levers  forward till you feel a distinctive click.

L CAUTION: Risk of unintended movement – Make sure the wheelchair is on a flat

horizontal surface before releasing the brakes. Never release both brakes

simultaneously.

To release the brakes:

1. Release one brake by pulling the lever  backwards.

2. Hold the hand-rim of the released wheel with your hand.

3. Release the second brake by pulling the lever  backwards.

Fig. A

Fig. B

V300DL

2016-03

Page10

2.7 Mounting or removing of armrests

The armrests of the wheelchair can be mounted by following instructions.

L CAUTION: Risk of clamping – Keep fingers, buckles and clothes away from the

bottom side of the armrest.

1. Mount the rear tube of the armrest in tube

hood

.

2. Make sure the armrest clicks in the locking

mechanism.

3. Fold the armrest forward.

4. Click the front tube of the armrest in tube

hood

.

To open and remove the armrest:

1. Press lever

 and pull the front of the armrest

upwards.

2. Fold the armrest backwards.

V300DL

2016-03

Page11

3. To remove the armrest, press button  and pull the rear of the armrest from

tube hood .

2.8 Adjusting the armrest

The height of the armrest can be adjusted in 8 positions (range 105 mm: steps 15 mm):

1. Push the lever .

2. Adjust the arm pad  in the desired height.

3. Loosen the lever

.

4. Check the arm pad  is firmly secured.

2.9 Adjusting anti-tipping (only mounted to the right side)

Adjust the height of the anti-tipping in 7 positions

(range 120 mm: steps 20 mm):

1. Loosen the star knob  a little bit.

2. Move the tube of the anti-tipping in the desired

height.

3. Secure the star knob

.

4. Check the anti-tipping is firmly secured.

V300DL

2016-03

Page12

2.10 Adjusting height hand grips

Adjust the height of the hand grips (range

120 mm: steps less):

1. Loosen the star knob  a little bit.

2. Move the hand grips in the desired

height.

3. Secure the star knob

.

4. Check the hand grips are firmly secured.

2.11 Transfer in and out the wheelchair

L

CAUTION: In case you cannot perform the transfer in a safe manner, ask

someone to assist you.

L CAUTION: Risk of tipping over of the wheelchair – Do not stand on the foot

plates.

1. Position the wheelchair as close as possible to

the chair, couch or bed to/from you wish to

transfer.

2. Check both brakes from the wheelchair are in

the on position.

3. Fold the foot plates upwards to prevent

standing on them.

4. If the transfer is on the side of the wheelchair,

fold the armrest on that side upwards

(see § 2.7) and fold the brake lever down.

5. Transfer to/from the wheelchair.

2.12 Correct position in the wheelchair

Some recommendations for a comfortable use of the wheelchair:

 Position your backside as close as possible to the back rest.

 Make sure your upper legs are horizontal – If needed adjust the length of the

footrests (see § 3.6).

2.13 Riding the wheelchair

L

WARNING: Risk of clamping – Prevent your fingers from being caught by the

wheels spokes.

L WARNING: Risk of clamping – Be careful passing through restricted passages

(e.g. doors).

L WARNING: Risk of burns – Be careful when driving in hot or cold environments

(sunshine, extreme cold, saunas, etc.) for a sufficient amount of time and when

touching - Surfaces can assume the environment temperatures.

V300DL

2016-03

Page13

1. Release the brakes.

2. Take both hand rims at their highest position.

3. Lean forward and push the hand rims forward until straight arms.

4. Swing your arms loosely back to the hand rims topside and repeat the movement.

2.14 Moving on slopes

L

WARNING: Control your speed – Moving on slopes as slow as possible.

L WARNING: Consider the capacities of your attendant – If your attendant does not

have enough force to control the wheelchair, put on the brakes.

L WARNING: Risk of tipping over – Lean forward to move your centre of gravity

forward. To improve a better stability.

1. If available on the wheelchair, wear the safety belt.

2. Do not attempt moving on too high slopes. The maximum

slope angles (upwards and downwards) are mentioned in

table 1.

3. Ask an attendant to help you moving on the slope.

4. Lean forward to move your centre of gravity forward.

2.15 Negotiating steps or curbs

2.15.1 Getting down steps or curbs

Riding down low curbs can be done moving forwards. Make sure that the footrests do not

touch the ground.

A practiced user can negotiate small steps or curbs by himself:

L WARNING: Risk of tipping over – If you do not have

enough experience with your wheelchair, ask

assistance of an attendant.

1. Bring balance on the rear wheels to reduce the pressure on

the front wheels.

2. Negotiate the curbs.

Higher curbs can be taken forward with an attendant:

1. Ask the attendant to tip the wheelchair slightly backwards.

2. Get past the curbs while moving on the rear wheels.

3. Put the wheelchair back on the four wheels.

An experienced user can negotiate higher curbs by himself. This is

best done backwards.

1. Turn the wheelchair to have the rear wheels facing the

curb.

2. Lean forward to move your centre of gravity forward.

3. Move the wheelchair close to the curbs.

4. Use the hand rim to roll-off wheelchair from the curb in a

controlled manner.

V300DL

2016-03

Page14

2.15.2 Moving up steps or curbs

Moving up steps or curbs with attendant as follows:

1. Prevent the footrests from touching the curb.

2. Ask the attendant to tip the wheelchair backwards, just

enough to move the front wheels over the curb.

3. Lean backwards to move your centre of gravity above the rear

wheel.

4. Place the front wheels on the curb.

5. Roll rear wheels of the wheelchair over the curb.

Higher curbs are negotiated backwards:

1. Turn the wheelchair to have the rear wheels facing the curb.

2. Lean backwards and move your centre of gravity above the rear wheels.

3. Ask the attendant to pull the wheelchair on the curb.

4. Take back the normal position in the wheelchair.

An experienced user can negotiate curbs by himself:

L WARNING: Risk of tipping over – If you have not enough experience to control

the wheelchair, get help from an attendant.

1. Drive until the curbs.

2. Ensure that the footrest do not touch the curbs.

3. Lean backwards so you are balancing on the rear wheels.

4. Role the front wheels balancing over the curbs.

5. Bend forwards for more stability.

6. Role the rear wheels over the curbs.

2.15.3 Taking of stairs

Taking of stairs while you staying in the wheelchair shall be according following rules:

L WARNING: Risk of tipping over – Taking of stairs shall always with 2 attendants.

1. Remove the footrests.

2. One attendant tip the wheelchair slightly backwards.

3. The second attendant take the front of the frame.

4. Stay calm, avoid sudden movements and keep your arms inside the wheelchair.

5. Take the steps on the rear wheels of the wheelchair.

6. Mounting the footrests back after taking the stair.

V300DL

2016-03

Page15

2.16 Fold up the wheelchair

L

CAUTION: Chance of pinching – Do not place your fingers between the

components of the wheelchair.

1. Fold the foot plates or remove the footrests (see § 2.5).

2. Swing the stabilisator away from the right hand grip (standing behind the wheelchair -

see § 2.4).

3. Take the seat on the front side and backside and pull it up.

2.17 Taking off the rear wheels

To facilitate the transport off the wheelchair the rear wheels can be taken off:

1. Make sure the brakes standing in the off

position.

2. Take the wheelchair to the side frame where

you want to remove the wheel.

3. Press the button

 in the center of the wheel

hub.

4. Pull the wheel away from the frame.

2.18 Transport in the car

L

WARNING: Risk of injury – See that the wheelchair is attached properly. So you

can avoid injury from the passengers during collision or sudden braking.

L WARNING: Risk of injury – Use for attaching the wheelchair and passenger

NEVER the same seatbelt.

1. Remove footrests and accessories.

2. Store footrests and accessories safely.

3. If possible, fold the wheelchair and remove the wheels.

4. Place the wheelchair in the luggage place.

5. If the wheelchair and the passenger compartment is NOT separated, attach the

frame of the wheelchair securely to the vehicle. You can use the available safety

belts in the vehicle.

V300DL

2016-03

Page16

2.19 Use of the wheelchair as seat in a motor vehicle

L

WARNING: The wheelchair has passed the crash test of ISO 7176-19: 2008

and, as such, has been designed and tested for use only as forward-facing seat

in a motor vehicle.

L WARNING: The wheelchair's pelvic belt alone is not suited as an occupant

restraint belt.

The wheelchair is tested using the four-point strap-tie system and a 3-point occupant-

restraint system.

Whenever feasible, use the seat of the vehicle and store the wheelchair in the cargo area.

Steps to secure the wheelchair in a motor vehicle:

1. Check that the vehicle is equipped with a suitable wheelchair tie down and occupant-

restraint system, conform ISO 10542.

2. Check that the components of the wheelchair tie down and occupant restraint system

are not frayed, contaminated, damaged or broken.

3. If equipped with an adjustable seat and/or back tilt, make sure that the wheelchair

user is sitting as upright as possible. If the user's condition prevents this, a risk

assessment should be done to evaluate the user's safety during transit.

4. Remove all mounted accessories such as trays and respiratory equipment, and

secure them in a safe place.

5. Position the wheelchair facing forward in the travelling direction, centrally between

the tie-down rails mounted in the floor of the vehicle.

6. Make sure that the indicated zones around the wheelchair user are clear from rigid

vehicle parts.

7. Mount the front securement straps according to the instructions of the strap-system

manufacturer at the indicated place. (figure 3)

This place is marked on the wheelchair with a symbol. (figure 4)

8. Roll back the wheelchair until the front straps are tight.

9. Apply the wheelchair brake.

10. Mount the back securement straps according to the instructions of the strap-system

manufacturer at the indicated place. (figure 3)

11. This place is marked on the wheelchair with a symbol. (figure 4)

V300DL

2016-03

Page17

figure 3

Steps to secure the wheelchair user:

1. Remove both armrests.

2. If present, attach the wheelchair's pelvic belt.

3. Attach the occupant restraint belts according to the instructions of the strap-system

manufacturer.

4. Wear the pelvic belt low across the front of the pelvis, so that the angle of the pelvic

belt is within the preferred zone of 30° to 75° to the horizontal, similar to that shown

below.

5. A steeper (greater) angle within the preferred zone is desirable.

6. Adjust the belt tightly according to the instructions of the strap-system manufacturer,

consistent with the user's comfort.

7. Ensure that the restraint belt connects in a straight line to the anchor point in the

vehicle and that no bends in the belt are visible, for instance at the axle of the rear

wheel.

8. Install the armrests, if desired. make sure that belts are not twisted or held away from

the body by wheelchair components such as armrests or wheels.

PELVIC RESTRAINTS SHOULD MAKE FULL

CONTACT ACROSS THE FRONT OF THE BODY

NEAR THE JUNCTION OF THE THIGH AND

PELVIS

RESTRAINTS SHOULD NOT BE

HELD AWAY FROM BODY BY

WHEELCHAIR COMPONENTS SUCH

AS ARMRESTS OR WHEELS

Figure 4

V300DL

2016-03

Page18

3 Installation and adjustment

The instructions in this chapter are for the specialist dealer.

The Vermeiren V300DL has been designed to be adjust with a minimum of replacements

parts.

There is no need for extra stock of spare parts.

To find a service facility or specialist dealer near you, contact the nearest Vermeiren facility.

A list of Vermeiren facilities can be found on the last page.

L WARNING: Risk of unsafe settings - Use only the settings described in this

manual.

L WARNING: Variation of allowed adjustments can still change the stability of your

wheelchair (tilt back or sideways).

3.1 Tools

To set up the wheelchair the following tools are needed.

 Wrench set n° 10 to n° 22

 Allen keyset n° 4 to n° 6

3.2 Manner of delivery

The Vermeiren V300DL shall be delivered with:

 1 frame with armrests, rear and front wheels (standard delivery

seat height: 500 mm without seat cushion, seat angle: 5°)

 Seat cushion

 Anti-tipping (only right side)

 1 pair footrests

 Tools

 Manual

 Accessories

3.3 Adjusting the seat height and seat angle

The Vermeiren V300DL is adjustable in 4 seat heights and 5 seat angles (0°-2,5°-5°-7,5°-

10°) by changing the position of the wheels for each height and angle there is a different

setting of the front and rear wheels.

The summary of the different seat heights by a standard seat angle 5° is tabulated below.

Seat height

(without seat cushion)

Rear wheels Front wheels

Hole Hole

Bushing Ⓑ relative to castor

stem housing Ⓒ

440 mm

 

Above

470 mm

 

Under

500 mm (Standard)

 

Under

530 mm

 

Under

Table 2: Seat heights by seat angle 5°

Strona jest ładowana ...

Vermeiren V300 DL Instrukcja obsługi

Vermeiren V300 DL Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty