Novus NVIP-3SD-6200/20 Instrukcja obsługi

User’ s ma n ua l

(s h ort form )

NVIP-3SD-6200/20

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

2

COMMENTS AND WARNINGS

THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING DIRECTIVES:

This appliance is marked according to the European 1000VAC Directive on Waste Electrical and Electronic

Equipment (2012/19/EU) and further amendments. By ensuring this product is disposed of correctly, you will

help to prevent potential negative consequences for the environment and human health, which could otherwise

be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be

treated as household waste. It shall be handed over to the applicable collection point for used up electrical and

electronic equipment for recycling purpose. For more information about recycling of this product, please contact

your local authorities, your household waste disposal service or the shop where you purchased the product.

Out of concern for human health protection and friendly environment, we assure that our products falling under

RoHS Directive regulations, regarding the restriction of the use of hazardous substances in electrical and

electronic equipment, have been designed and manufactured in compliance with the above mentioned

regulations. Simultaneously, we claim that our products have been tested and do not contain hazardous

substances whose exceeding limits could have negative impact on human health or natural environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self

installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices

during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN

USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES

NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE

CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR

THE RESULTS OF SUCH AN ACTION.

DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 26

February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic

compatibility (OJ L 96, 29.3.2014, p. 79–106, with changes)

DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July

2012 on waste electrical and electronic equipment (WEEE) (OJ L 197, 24.7.2012, p. 38–71, with changes)

DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 8 June

2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (OJ L

174, 1.7.2011, p. 88–110, with changes)

DIRECTIVE 2014/35/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 26 February 2014 on the harmonisation of the laws of the Member States

relating to the making available on the market of electrical equipment designed for use within certain voltage

limits.

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

3

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER DEVICE

OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH THE MANUAL PRIOR

TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER-

SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL MAY OPEN THE

UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE PERSONNEL

AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is

necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is

forbidden;

7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath

tubs, damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is

not recommended since it may lead to heat build-up and damaging the device itself as a consequence;

9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be

mounted by qualified personnel with proper authorization, in accordance with this user’s manual;

10. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the

camera from a power sources with unknown parameters, unstable or not meeting producer’s

requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions described in the

manual in question may change without further notice.

We strongly suggest visiting the www.novuscctv.com website in order to access the newest manual.

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

4

FOREWORD INFORMATION

1. FOREWORD INFORMATION

1.1. General characteristic

• Mechanical IR cut filter

• IR operation capability - built-in IR LED illuminator

• Imager resolution: 3 megapixels

• Min. Illumination: from 0 LX with IR off

• Motor-zoom lens, AI and AF function

• Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions

• 8 tours (max. 16 presets each)

• 2 auto-scan functions

• 4 patterns (max. 180 sec. per pattern)

• 235 preset commands

• Optical zoom: up to 20x

• “Auto-Flip” function allows the tilt to rotate 180° and reposition itself for continuous viewing of a

moving object directly beneath the dome

• Compression: H.264/H.265 or M-JPEG

• Bidirectional audio transmission

• Video processing resolution: up to 2048 x 1536

• RTP/RTSP protocol support for video & audio transmission

• Triple stream mode: compression, resolution, speed and quality defined individually for each video

stream

• Network connection control function

• Built-in web server: camera configuration through the website

• Diverse definition of system reactions to alarm events: e-mail with attachment, saving file on FTP

server, alarm output trigger, HTTP notification, PTZ function activation

• PTZ control directly from the website and NMS (NOVUS MANAGEMENT SYSTEM)

• Schedule recording function

• Network protocols support: ONVIF(2.3) Profile S, HTTP, HTTPS, TCP/IP, IPv4/v6, UDP/IP, FTP,

DHCP, DDNS, NTP, RTSP, SMTP, PPPoE

• Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,

playback and remote IP devices administration

• IP 66

• Housing and wall mount bracket in-set included

• Power supply: 24 VDC (power supply included) or 24VAC

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

5

FOREWORD INFORMATION

Image

Image Sensor 3 MPX CMOS sensor 1/2.8” SONY

Number of Effective Pixels 2048 (H) x 1536 (V)

Min. Illumination

4.0 lx/F1.6 - color mode

0 lx (IR on) - B/W mode

S/N Ratio > 48 dB (AGC off)

Electronic Shutter auto: 1/25 s ~ 1/10000 s

Wide Dynamic Range (WDR) yes

Digital Noise Reduction (DNR) 3D

Defog Function (F-DNR) yes

Lens

Optical Zoom 20x

Lens Type motor-zoom, auto-iris function, f=5.5 ~ 110 mm/F1.6 ~ F3.5

Auto-focus continuous, zoom trigger, day/night mode trigger

Day/Night

Switching Type mechanical IR cut filter

Switching Mode auto, manual, time

Visible Light Sensor yes

Network

Stream Resolution

2048 x 1536 (QXGA), 1920 x 1080 (Full HD), 1280 x 720 (HD), 640

x 480 (VGA), 320 x 240 (QVGA)

Frame Rate 30 fps for each resolution

Multistreaming Mode 3 streams

Video/Audio Compression H.264, H.265, MJPEG/G.711

Number of Simultaneous Connections max. 4

Bandwidth 18 Mb/s in total

Network Protocols Support

HTTP, TCP/IP, IPv4, UDP, DHCP, DDNS, NTP, RTSP, PPPoE,

SMTP

ONVIF Protocol Support Profile S (ONVIF 2.3)

Camera Configuration

from Internet Explorer browser

languages: Polish, English

Compatible Software NMS

PTZ

Preset Commands 235

Tours 8 (up to 16 presets per tour)

Auto-Scans 2

Patterns 4 (max. 180 s for each pattern)

Tilt/Pan Range 0° ~ 93°/360° (continuous)

Pan/Tilt Speed up to 160°/s (proportional to zoom)

Preset Speed up to 240°/s

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

6

FOREWORD INFORMATION

1.3. Camera dimensions

Other functions

Access Password number of characters: 4 numbers

Motion Detection yes

Image Processing 180˚ image rotation, sharpening, mirror effect

System Reaction to Alarm Events e-mail with attachment, alarm output activation, HTTP notification, PTZ

IR LED

LED Number 4

Range up to 100 m (depends on current optical zoom value)

Angle up to 45° (depends on current optical zoom value)

Interfaces

Vide output BNC, 1.0 Vp-p, 75 Ohm - AHD/TVI 1080p

Audio Input/Output 1 x Jack (3.5 mm)/1 x Jack (3.5 mm)

Alarm Input/Output 4 (NO/NC)/1 relay type

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

SD Card slot Micro SD card up to 64GB

Installation parameters

Dimensions (mm) 208 (Ф) x 317 (H), with bracket: 205 (W) x 470 (H) x 313 (L)

Weight 3.5 kg, with bracket: 4.2 kg

Degree of Protection IP 66

Enclosure

aluminium, white, in-set included: outdoor housing (integrated with the cam-

era), wall mount bracket

Power Supply Power supply 24 VAC

Power Consumption

15 W (IR on)

30 W (IR and heater on)

Operating Temperature -20°C ~ 60°C

Built-in Heater/Fan yes/no

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

7

START-UP AND INITIAL IP CAMERA CONFIGURATION

1.4. Package contents

After you open the package make sure that the following elements are inside:

If any of this elements has been damaged or missing during transport, pack all the elements back into

the original box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches

the temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular in-

puts, outputs and adjusting elements that the device is equipped with.

2. START-UP AND INITIAL IP CAMERA CONFIGURATION

2.1. Description of connectors

1. RJ-45 connector

2. Audio Output

3. Audio Input

4. Alarm Input/Output

5. Power connector 24VAC/24VDC

6. RS-485 connector

7. BNC AHD/TVI signal output

8. Grounding

Novus IP PTZ camera 1 pcs

Wall bracket 1 pcs

User’s manual (short form) 1 pcs

Power supply 1pcs

24 VDC +

24 VDC -

Power connection 24VDC

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

8

START-UP AND INITIAL CAMERA CONFIGURATION

Configurtion of AHD/TVI and RS485

DIP switch describe:

1: ON: AHD, OFF: TVI

2: ON: Pelco-P, OFF: Pelco-D

3-4: Bitrate configuration

5-10: PTZ address configuration

Camera Got PTZ settings that user can be change in PTZ

Settings tab.

User have to choose between Software settings (SW) or

Hardware (HW).

2.2. Mounting the camera

In order to obtain declared degree of protection please seal the mounting place additionally with

appropriate sealing mass, paying special attention to mounting holes.

The declared degree of protection of the camera relates to its housing and does not take into account

the possibility of moisture infiltration into the interior of the camera by connecting cables.

Connection cables protection through i.e. sealing up is the responsibility of the camera installer. The

manufacturer is not liable for any damages to the camera caused as a result of failing in performing

that activity by installer, which also means that camera damaged in that way is not subject to

warranty repairs.

CAUTION!

Due to safety reasons, maximum load capacity of surface shouldn’t be less than 25kg.

In order to successfully mount a camera, please follow the procedure below:

• Put the bracket to the wall in a desired mounting place (with cable hole). Taking the bracket’s

base screw holes as a pattern, mark future drilling holes for screws using a punch.

• Drill 4 holes in accordance with previously done markings, insert the expansion plugs into the

holes.

• Thread the wires through the hole in the wall bracket.

• Attach the camera to the bracket and rotate the camera clockwise to align screw holes on the

installing base of the camera and the bracket.

• Then tighten the three screws to fix the bracket and camera.

PIN4 PIN 3 BITE RATE

OFF OFF 1200

OFF ON 2400

ON OFF 4800

ON ON 9600

PIN10 PIN9 PIN8 PIN7 PIN6 PIN5 Address code

0 0 0 0 0 0 0

0 0 0 0 0 1 1

0 0 0 0 1 0 2

0 0 0 0 1 1 3

0 0 0 1 0 0 4

0 0 0 1 0 1 5

0 0 0 1 1 0 6

... ... ... ... ... ... ...

1 1 1 1 1 1 63

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

9

• In order to Then tighten the three screws to fix the bracket and camera.

• By using the description of the terminals from the previous chapter and the appropriate

accessories, connect required signal and power supply cables.

CAUTION!

Connection the power cable to the camera must be performed after disconnecting the power

source. Power can be on only after the camera is fully mounted.

• Put the excess cable back into the bracket.

• Screw on the camera with the bracket to the wall.

• After the above steps the camera is ready to work

START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

10

2.3. Starting the IP camera

To run NOVUS IP camera you have to connect 24 VDC or 24 VAC power, at least 60W.

Initialization process takes about 2 minutes. Then you can proceed to connect to the camera via web

browser.

The recommended way to start an IP camera and perform its configuration is a connection to the PC

via the network switch which is not connected to other devices.

To obtain further information about network configuration parameters (IP address, gateway, network

mask, etc.) please contact your network administrator.

• Connection utilizing external power supply and network switch

• Network connection using external power supply, directly to the computer.

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission

Network

transmission

Network Switch

Computer

IP Camera

Network transmission - cross over cable

Computer

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

11

CAUTION!

In order to provide protection against voltage surges/lightning strikes, usage of appropriate

surge protectors is advised. Any damages resulting from surges are not eligible for service

repairs.

2.4. Initial configuration via the web browser

The default network settings for NVIP-3SD-6200/20 camera are :

1. IP address- 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to set PC IP address appropriately, so the two devices can

operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera is from

range 192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same

addresses for camera and PC computer

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

12

NETWORK CONNECTION VIA WEB BROWSER

3. NETWORK CONNECTION VIA WEB BROSWER

3.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming image display in 2048x1536

resolution and 30 fps speed.

1. CPU Intel Core i3 3GHz or newer

2. RAM Memory min. 4 GB

3. VGA card (displaying Nvidia GeForce 512MB Ram or equivalent )

4. OS Windows 7/8/8.1/10

5. Network card 100/1000 Mb/s

3.2. Connection with IP camera via web browser

You have to enter camera IP address in the address bar. When you connect to the camera, web browser

will download the applet for displaying images from the camera. In Internet Explorer it may be

necessary to accept an ActiveX control. To do this, click the right mouse button on the message, select

"Install Active X control" and then click Install. After successfully NetIPCamera plug in downloading

run and install it on a computer.

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

13

. If the installation fails, changing security settings for the IE browser is required. In order to do that,

please choose: Tools > Internet options > Security tab > Custom level and:

• Under Download unsigned ActiveX controls - select either Enable or Prompt

• Under Initialize and script ActiveX controls not marked as safe - select Enable or Prompt

You can also add the camera’s IP address to “trusted zone” and set lowest security level for it.

In addition, when working in Windows Vista/7 the ActiveX applet may be blocked by Windows

Defender or User account control. In such case you should allow to run this applet, or simply disable

these functions.

After successful installation login window will be displayed. Default user is root and default password

is pass. For safety reasons, it is recommended to change default user name and password.

NETWORK CONNECTION VIA WEB BROWSER

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

14

NETWORK CONNECTION VIA WEB BROWSER

NOTE: If you are running Windows Vista/7/8 with Internet Explorer 11, the ActiveX applet can be

blocked through browser security settings. In this situation, you should: add the IP address of the ca-

mera to the view of compatibility (Tools -> Compatibility View Settings, click Add).

Then, in the security settings options, add the camera address to trusted sites and lower the security

level to a minimum.

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

15

NETWORK CONNECTION VIA WEB BROWSER

After making the changes, restart the browser, re-connect to the camera and log on.

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

16

4. WWW INTERFACE - WORKING WITH IP CAMERA

4.1. Displaying live pictures

1. .Picture settings

Original Size Automatic Size

Fit to screen Full screen

2. Camera functions

Live view on/off

Two way audio

Sound on/off

Make a snapshot

WWW INTERFACE - WORKING WITH IP CAMERA

Record a video

3D PTZ control

Digital Zoom

PTZ Menu on/off

3

4

5

1

2

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

17

2. Video Parameter

Stream - Stream ID (choose one from available streams)

Bite Rate Type - Information about bit rate type

Bit Rate (kbps) - Information about bit rate

I Frame Interval - Information about I frame interval

Quality - Information about quality

USE TIME STAMP - Video buffer (increases delay when enabled, maximum delay is 5s)

NOTICE: USE TIME STAMP function will not be available when using Flash instead of ActiveX.

3. PTZ Control Panel

PTZ Configure:

Preset - Programming, deleting, and recalling presets

Track - Programming, deleting, and recalling tracks

Speed - Setting speed of movement

3D Position - Turns on/off control using the mouse

North - Setting orientation of the camera

Timer - Setting schedules

PTZ Control:

Arrow keys - Controlling the movement of the camera: up/down, right/left

„Home” key - Function unavailable

Zoom - Zoom control

Focus - Focus control

Iris - Function unavailable

Brush - Function unavailable

On/Off IR - Function unavailable

4. Menu bar

Change Password - Change users password

NOTICE: Default password "pass" can be restored only after restoring default settings of the camera)

Sign Out - Log out from camera

5. Video Control

Camera - Default number of the camera is 1.

Video - Turn on/off video

Audio - Turn on/off audio

Interphone - Turn on/off Interphone

NOTICE: Audio and Interphone functions will not be available when using Flash instead of Activex.

WWW INTERFACE - WORKING WITH IP CAMERA

3. PTZ Menu

PTZ control Panel

PTZ

speed slider (1-8)

Scan mode

Wiper (not available)

IR Led switch (On/Off/Auto)

PTZ function:

Preset Settings

Cruise Settings

Trace Settings

Delete Preset

Call Preset

Save Preset

4. Alarm Icons:

5. Settings Tab

Live - Live preview

Config - Advanced camera configuration

Search - Searching for camera records/pictures

Logout - Logout from camera

Motion detection

Alarm 1-4

Camera zoom settings

Camera focus settings

Camera Iris settings

Random Scan mode

Group Scan mode

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

18

ELECTRIC CONNECTORS AND ACCESORIES

5. ELECTRIC CONNECTORS AND ACCESORIES

5.1. Connecting power supply to the camera.

Camera can be supplied using external power supply unit corresponding with the camera parameters.

When selecting the power supply should also be take into account the power consumption of the heater,

unless the camera will not be used at temperatures below 0 °C, or the heater will have its own power

supply.

CAUTION!

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

5.2. Connecting Alarm Input/Output

For alarm Input:

• Alarm input (NO type): Connect DC5V~DC12V voltage between the alarm input port( ALM-

INA, ALM-INA, ALM-INB, ALM-INC, ALM-IND ) and the grounding port (ALM-GND).

• Alarm input (NC type): Disconnect the voltage between the alarm input port (ALM-INX) and the

grounding port (ALM-GND).

Alarm Output:

• Support 1CH alarm output including OPEN, COM connections.

• Alarm output: One passive switch for user to connect alarm devices; the alarm output state will

be auto on/off according to your setting.

5.3 Audio Input/Output

The camera has two connectors audio jack. To connect an external speaker or microphone (MIC/LIN).

5.4 Connection RS482

Camera got RS-485 Connector to connect with external PTZ keyboard. To properly connect keyboard

user need to connect Keyboard Tx+ connector with camera RS485A port. And connector Tx– with

camera RS485B port.

NVIP-3SD-6200/20 User’s manual (short form) ver.1.2

19

5.5 Instaslling MicroSD card

To install micros sd card in camera, user need to remove cover form

back. Put SD card next to the RESET button. Reattach the flap that

secures the MicroSD card slot

6. RESTORING FACTORY DEFAULTS

NOVUS IP cameras allow to restore defaults via:

• Software (web browser level)

• Hardware (using reset button)

6.1. Software restoration of factory settings the IP camera

User can restore default settings. To restore to default settings go to: Maintenance -> Device Restart

tab. Process of restoring takes about two minutes.

6.2. Hardware restoration of factory settings the IP camera

In order to restore factory defaults for the camera please follow the instructions:

• Unscrew the screws holding cover at the back of the dome

• Press the RESET button (when camera is powered) and hold on for about 10 seconds

• Release button

• Wait until the camera starts (finished positioning of the dome) - it takes abort 2 minutes

• Turn power off, mount cover back, turn the camera on

• Log on using default IP address (http://192.168.1.200) and default user name (root) and password

(pass)

RESTORING FACTORY DEFAULTS

2020-07-16 MO (MO, MK)

AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.

431 Pulawska St., 02-801 Warsaw, Poland

tel.: +4822 546 07 00, fax: +4822 546 07 59

www.novuscctv.com

Strona jest ładowana ...

Novus NVIP-3SD-6200/20 Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Novus NVIP-3SD-6200/20 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty