Novus NVIP-3DN7030SD/IRH-2P Instrukcja obsługi

User’s ma n ua l

(s h o rt )

NVIP-3DN7030SD/IRH-2P

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

2

IMPORTANT SAFEGUARDS AND WARNINGS

EMC (2004/108/EC) and LVD (2006/95/EC ) Directives

CE Marking

Our products are manufactured to comply with requirements of the following directives and national regulations

implementing the directives:

Electromagnetic compatibility EMC 2004/108/EC.

Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical equipment designed

for use with a voltage rating of between 50VAC and 1000VAC as well as 75VDC and 1500VDC.

WEEE Directive 2012/19/EU

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European 1000VAC Directive on Waste Electrical and

Electronic Equipment (2012/19/EU) and further amendments. By ensuring this product is disposed of

correctly, you will help to prevent potential negative consequences for the environment and human health, which

could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be

treated as household waste. It shall be handed over to the applicable collection point for used up electrical and

electronic equipment for recycling purpose. For more information about recycling of this product, please contact

your local authorities, your household waste disposal service or the shop where you purchased the product.

RoHS Directive 2011/65/EU

Out of concern for human health protection and friendly environment, we assure that our products falling under

RoHS Directive regulations, regarding the restriction of the use of hazardous substances in electrical and

electronic equipment, have been designed and manufactured in compliance with the above

mentioned regulations. Simultaneously, we claim that our products have been tested and do not

contain hazardous substances whose exceeding limits could have negative impact on human health

or natural environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self

installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices

during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN

USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT

DOES NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER

MUST BE CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S

RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

3

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER

-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL

MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is

necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is forbidden;

7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,

damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions described in the

manual in question may change without further notice. We strongly suggest visiting the www.novuscctv.com

website in order to access the newest manual

Data included in the following user’s manual is up to date at the time of printing. AAT Holding S.A.. holds

exclusive rights to modify this manual. The producer reserves the rights for device specification modification

and change in the design without prior notice.

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

4

TABLE OF CONTENTS ..................................................................................................... 4

1. FOREWORD INFORMATION ................................................................................... ..5

1.1. General Characteristics ........................................................................................ 5

1.2. Technical specification .................................................................................... ...6

1.3. Camera dimension ........................................................................................... ...8

1.4. Package contents ............................................................................................... ...9

2. START-UP AND INITIAL IP CAMERA CONFIGURATION ............................... 10

2.1. Description of connectors and control tools ...................................................... 10

2.2 Connecting power supply to the camera …..………….………………………10

2.2. Camera mounting .............................................................................................. 11

2.3. Starting the IP camera ........................................................................................ 12

2.4. Initial configuration via the Web browser ......................................................... 13

3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................ 14

3.1. Recommended PC specification for web browser ............................................. 14

3.2. Connection with IP camera via the Internet Explorer ........................................ 14

3.3. Connection with IP camera via the other browser ............................................. 16

4. WWW INTERFACE - WORKING WITH IP CAMERA ......................................... 18

4.1. Displaying live pictures. ..................................................................................... 18

4.2. Displaying live pictures - PTZ control. .............................................................. 20

5. ELECTRIC CONNECTORS AND ACCESORIES ................................................. 21

5.1. Connecting audio and inputs/outputs ................................................................. 21

5.3. SD card installation ........................................................................................... 21

5.4 BNC connection ..…………………………………………………………… ...22

6. RESTORING FACTORY DEFAULTS ..................................................................... 23

6.1. Restoring software factory defaults .................................................................... 23

6.2. Restoring hardware factory defaults in IP cameras ........................................... 23

TABLE OF CONTENTS

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

5

1. FOREWORD INFORMATION

1.1. General Characteristics

• Mechanical IR cut filter

• IR operation capability

• Imager resolution: 3 megapixels

• Min. Illumination: from 0.01 lx/F=1.6

• Motor-zoom lens, AI and AF function

• Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions

• Digital Slow Shutter (DSS)

• 8 tours (max. 64 presets each)

• 4 auto-scan functions

• 8 patterns (max. 206 s)

• 256 preset commands

• Privacy zones: 20

• Optical zoom: up to 30x

• 4 alarm inputs & 2 alarm relay outputs (NO/NC)

• “Auto-Flip” function allows the tilt to rotate 180° and reposition itself for continuous viewing of a moving object

directly beneath the dome

• Compression: H.264 or M-JPEG

• Bidirectional audio transmission

• Video processing resolution: up to 2048 x 1536

• RTP/RTSP protocol support for video & audio transmission

• Quadruple stream mode: compression, resolution, speed and quality defined individually for each video stream

• Hardware motion detection

• Network connection control function

• Built-in web server: camera configuration through the website

• Diverse definition of system reactions to alarm events: e-mail with attachment, saving file on FTP server, saving

on NAS server, saving file on SDXC card, alarm output trigger, HTTP notification, PTZ function activation

• PTZ control directly from the website and NMS (NOVUS MANAGEMENT SYSTEM)

• Schedule recording function

• Network protocols support: ONVIF (2.6/Profile S), HTTP, TCP/IP, IPv4/v6, UDP, HTTPS, FTP, DHCP, DDNS,

NTP, RTSP, RTP, UPnP, SNMP, QoS

• Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring, playback and

remote IP devices administration

• IP 66

• Installation:

-wall mount using bracket in-set included,

• Housing, wall mount bracket

• Power supply: 24 VAC/12VDC

FOREWORD INFORMATION

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

6

1.2. Technical specification

FOREWORD INFORMATION

Parameters

Description

NVIP-3DN7030SD/IRH-2P

Image Sensor

3 MPX CMOS sensor 1/2.8” SONY

Number of Effective Pixels

2048 (H) x 1536 (V)

Min. Illumination

0.04 lx/F1.6 - color mode (DSS),

0.01 lx/F1.6 - B/W mode (DSS)

0 lx/F=1.6 –B/W mode (IR ON)

Electronic Shutter

auto/manual: 1/1 s ~ 1/10000 s

Digital Slow Shutter (DSS)

up to 1 s

Wide Dynamic Range (WDR)

yes

Digital Noise Reduction (DNR)

2D,3D

LENS

Optical Zoom

30x

Lens Type

motor-zoom varifocal, AI and AF function,

f=4.3 ~ 129 mm/F1.6 ~ F4.7

DAY/NIGHT

Switching Type

mechanical IR cut filter

Switching Mode

auto, manual, time

Switching Schedule

yes

NETWORK

Stream Resolution

2048 x 1536 (QXGA), 1920 x 1080 (Full HD), 1280 x 1024

(SXGA), 1280 x 720 (HD), 1024 x 768 (XGA), 800 x 600 (SVGA),

720 x 576 (D1), 640 x 480 (VGA), 352 x 288 (CIF), 320 x 240

(QVGA)

Frame Rate

60 fps for all resolutions

Video/Audio Compression

H.264, MJPEG/G.711, G.726

Number of Simultaneous Con-

nections

max. 10

Bandwidth

50 Mb/s in total

Network Protocols Support

HTTP, TCP/IP, IPv4/v6, UDP, HTTPS, Multicast, FTP, DHCP,

DDNS, NTP, RTSP, RTP, UPnP, SNMP, QoS, PPPoE

ONVIF Protocol Support

Profile S (ONVIF 2.6)

Camera Configuration

from Internet Explorer browser

languages: Polish, English, Russian, and others

Compatible Software

NMS

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

7

FOREWORD INFORMATION

PTZ

Preset Commands

256

Tours

8 (up to 64 presets per tour)

Auto-Scans

4

Patterns

8

Tilt/Pan Range

-20° ~ 200°/360° (continuous)

Pan/Tilt Speed

up to 90°/s (proportional to zoom)

Preset Speed

up to 300°/s

OTHER FUNCTIONS

Privacy Zones

20

Motion Detection

yes

Image Processing

90˚ image rotation, 180˚ image rotation, sharpening, mirror effect

Prealarm/Postalarm

up to 3 s or 20 frames/up to 9999 s or 20 frames

System Reaction to Alarm

Events

e-mail with attachment, saving file on FTP server, saving file on SD

card, saving file on NAS server, alarm output activation, HTTP no-

tification, PTZ

INTERFACES

Video Output

BNC, 1.0 Vp-p, 75 Ohm - maintenance only

Audio Input/Output

1/1

Alarm Input/Output

4 (NO/NC)/2 relay type

Network Interface

1 x Ethernet - RJ-45 interface, 10/100/1000 Mbit/s

Memory Card Slot

SD

INSTALLATION PARAMETERS

Dimensions (mm)

207 (W) x 399 (H) x 260 (L) with bracket

Weight

3 kg with bracket: 3.8 kg

Enclosure

aluminium/plastic, white, poly-carbonate bubble, in-set included:

outdoor housing (integrated with the camera), wall mount bracket

Power Supply

24 VAC, 12VDC

Power Consumption

14 W,

29 W (IR on.)

41.5 W (Heater and IR on)

Operating Temperature

-40°C ~ 50°C

Built-in Heater/Fan

yes/yes

Degree of Protection

IP 66

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

8

FOREWORD INFORMATION

1.3. Camera dimensions

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

9

FOREWORD INFORMATION

1.4. Package contents

After you open the package make sure that the following elements are inside:

1x Wall mount bracket

1x Speed dome camera

1x Securing screw

2x Connectors

1x Manual

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches

the temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular in-

puts, outputs and adjusting elements that the device is equipped with.

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

10

2. START-UP AND INITIAL IP CAMERA CONFIGURATION

2.1. Description of connectors and control tools

1. Audio/Alarm I/O & RS-485 connector

2. Power connector for 12VDC

3. Gigabit Ethernet connector

4. Power connector for 24VAC

5. BNC connector

6. ’Reset’ button for

2.2. Connecting power supply to the camera

The camera can be supplied using an external power supply with parameters compatible with

camera specification .

CAUTION!

Incorrect connection of power supply wires may result in damage that is not covered by

warranty.

The camera is 24 VAC or 12VDC supplied.

Minimal required power output for the power supply unit should be at least: 60W

In order to provide protection against voltage surges/lightning strikes, usage of appropriate

surge protectors is advised. Any damages resulting from surges are not eligible for service

repairs.

Information: Power supply adapter is not included. Please use power adapter with parameters

specified in user’s manual.

START-UP AND INITIAL CAMERA CONFIGURATION

Pin Symbol Power description 24 VAC

1

AC1 Power input 24 VAC

2

Ground

3

AC2 Power input 24 VAC

24VAC

Power

Supply

12VDC

Power

Supply

Pin Power description 12VDC

Inner Pin

+12VDC

Outher Pin

Ground

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

11

2.3. Mounting the camera

In order to obtain declared degree of protection please seal the mounting place additionally with

appropriate sealing mass, paying special attention to mounting holes.

CAUTION!

Due to safety reasons, maximum load capacity of surface shouldn’t be less than 25kg.

In order to successfully mount a camera, please follow the procedure below:

• Put the bracket to the wall in a desired mounting place (with cable hole). Taking the bracket’s

base screw holes as a pattern, mark future drilling holes for screws using a punch.

• Drill 4 holes in accordance with previously done markings and base

hole placement.

• Remove the plastic cover located at the bottom of the bracket.

• Put required cables through the bracket’s arm (or through the hole located in

the plastic cover).

• Mount the bracket, paying special attention to mounting place and all

mounting holes and additionally sealing them with appropriate sealing mass if

necessary.

• You need to seal the thread connection, connecting camera to wall

mount.

• Attach the camera mounting base to the bracket by turning it to the left and tighten a suitable

screw in set included (see figure on next page).

• Connect required signal and power supply cables.

CAUTION!

Connection the power cable to the camera must be performed after disconnecting the power

source. Power can be on only after the camera is fully mounted and the protective elements of

camera module are dismounted.

• Using safety cable, attach the dome to the bracket.

• Attach the camera to the mounting base by turning it to the right and tighten a suitable screw

in set included.

• Put the excess cable back into the bracket.

• Place where the cables getting out of the bracket must be sealed with a sponge seal in set

included.

• Attach the plastic cover located at the bottom of the bracket.

START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

12

2.4. Starting the IP camera

To run NOVUS IP camera you have to connect 24 VAC or 12 VDC power supply or Ethernet cable

between camera and High PoE network switch with parameters compatible with camera power supply

specification.

Initialization process takes about 30 seconds. You can then proceed to connect to the camera via web

browser.

The recommended way to start an IP camera and perform its configuration is a connection to the PC via

the network switch which is not connected to other devices.

To obtain further information about network configuration parameters (IP address, gateway, network

mask, etc.) please contact your network administrator.

• Connection utilizing external power supply and network switch

• Connection utilising external power supply directly to the computer

Information:

Power supply adapter is not included. Please use power adapter with parameters specified in user ‘s

manual.

CAUTION!

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.’

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission

Network

Network Switch

Computer

IP Camera

Network

transmission

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

13

2.5. Initial configuration via the web browser

Network configuration of the camera can be performed utilizing web browser.

The default network settings for NVIP-3DN7030SD/IRH-2P camera are: :

1. IP address= 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can

operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from

192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for

camera and PC computer

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

14

3. NETWORK CONNECTION UTILIZING WEB BROSWER

3.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming smooth image display

in 1920x1080 resolution and 25 fps speed.

1. CPU Intel Core i3 3 GHz or newer

2. RAM Memory min. 4 GB

3. Graphic card NVIDIA GeForce 512 MB or equivalent

4. OS Windows Windows 7 / 8 / 8.1 / 10

5. Network card 100/1000 Mb/s

3.2. Connection with IP camera via the Internet Explorer

You have to enter camera IP address in the Internet Explorer address bar. If IP address is correct user

login window will be displayed:

Default user is root and default password is pass.

For safety reasons, it is recommended to change default user name and password.

When you log on to the camera, web browser will download the applet for displaying images from the

camera. Depending on the current Internet Explorer security settings it may be necessary to accept

an ActiveX control. To do this, click the right mouse button on the message, select "Install Active X

control" and then click Install. After successfully NVIP Viewer plug in downloading run and install

it on a computer.

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

15

If the installation fails, changing security settings for the IE browser is required. In order to do that,

please choose: Tools > Internet options > Security tab > Custom level and:

• Under Download unsigned ActiveX controls - select either Enable or Prompt

• Under Initialize and script ActiveX controls not marked as safe - select Enable or Prompt

You can also add the camera’s IP address to “trusted zone” and set lowest security level for it.

In addition, when working in Windows Vista/7/8/10 the ActiveX applet may be blocked by Windows

Defender or User account control. In such case you should allow to run this applet, or simply disable

these functions.

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

16

3.3. Connection with IP camera via other browser eg. Chrome, Mozilla Firefox, Safari )

It is also possible to connect to the camera using Mozilla Firefox, but this browser doesn't offer full

functionality of the camera, so the recommended browser is Internet Explorer.

The first run of the IP camera in browser is very similar to the IE version. After you type the correct IP

address you have to write correct username and password. The default user is root and password

is pass.

Next, blank screen is displayed. Then you have to install the missing Quick Time plug-in from site:

http://www.apple.com/quicktime/download/

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

17

After downloading and running it, a window depicting installation of particular components is then

displayed. After proper installation pictures from the camera should become visible

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

18

4. WWW INTERFACE - WORKING WITH IP CAMERA

4.1. Displaying live pictures

1. Main tabs

Home — live view and PTZ control page

System — camera settings ( IP, recording, sending alarm messages, motion detection)

Streaming — streaming settings for audio and video audio

PTZ — picture and PTZ functions settings

Logout

2. Language selection.

3. Live view video format selection.

4. ActiveX settings for live video:

- Display mode in web browser

- Full screen view

- Microphone - enable audio from microphone

- Speaker - enable audio sending to the camera

WWW INTERFACE - WORKING WITH IP CAMERA

1.

2.

3.

6.

4.

7.

5.

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

19

- Snapshot - saves the current frame in JPEG format

- Video Streaming pause/play button

- Web recording to AVI button

- Activates events defined in “System“ -> “Events“ -> “Manual trigger” tab

- Additional PTZ control panel. After selecting the following menu appears:

a - calling Preset in the range of 1 to 10.

b - calling Pattern (cruise) in the range of 1 to 8.

c - calling Tour (sequence) in the range of 1 to 8.

d - Pan/Tilt speed selecting in the range of 1 to 10.

e - Focus Far

f - Focus Near

g - Auto Focus mode enabling

h - Iris Close

i - Iris Open

j - Auto Iris mode enabling

k - Zoom In

l - Zoom Out

m - Pan/Tilt camera control

WWW INTERFACE - WORKING WITH IP CAMERA

m

b

c

d

e

i

g

f

h

k

l

j

a

NVIP-3DN7030SD/IRH-2P User’s manual (short form) ver.1.3

20

5. Available resolutions.

6. Zoom control. Slider allows to change zoom in the range from x1 to x30.

7. Focus control.

4.2. Displaying live pictures - PTZ control

Default Pan/Tilt camera control mode is emulated joystick mode. In this mode push and hold left mouse

button on the image in order to control the camera Pan/Tilt. The second Pan/Tilt control mode is set

center mode. In this mode camera sets automatically the center of the image in the place where you

click the left mouse button. Zoom control is performed using mouse wheel.

After click right mouse button on the image the menu including below options occurs:

After click right mouse button on the image the menu including below options will occur:

full screen/normal view - enable/disable full screen mode.

set center mode/set emulated joystick mode - select Pan/Tilt control mode

CONNECTORS AND ACCESORIES

- Zoom Out

- Zoom In

- Auto Focus mode enabling

- Manual Focus mode enabling

- Focus Near

- Focus Far

Strona jest ładowana ...

Novus NVIP-3DN7030SD/IRH-2P Instrukcja obsługi

Novus NVIP-3DN7030SD/IRH-2P Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty