Novus NVIP-3SD-8200/30 Instrukcja obsługi

U s e r ’s m a n u a l

NVIP-5000 series IP PTZ camera

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

2

IMPORTANT SAFEGUARDS AND WARNINGS

EMC (2004/108/EC) and LVD (2006/95/EC ) Directives

CE Marking

Our products are manufactured to comply with requirements of the following directives and national regulations

implementing the directives:

 Electromagnetic compatibility EMC 2004/108/EC.

 Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical

equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as

75VDC and 1500VDC.

WEEE Directive 2002/96/EC

Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European 1000VAC Directive on Waste Electrical and Electronic

Equipment (2002/96/EC) and further amendments. By ensuring this product is disposed of correctly, you will

help to prevent potential negative consequences for the environment and human health, which could otherwise

be caused by inappropriate waste handling of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be

treated as household waste. It shall be handed over to the applicable collection point for used up electrical and

electronic equipment for recycling purpose. For more information about recycling of this product, please contact

your local authorities, your household waste disposal service or the shop where you purchased the product.

RoHS Directive 2002/95/EC

Out of concern for human health protection and friendly environment, we assure that our products

falling under RoHS Directive regulations, regarding the restriction of the use of hazardous

substances in electrical and electronic equipment, have been designed and manufactured in

compliance with the above mentioned regulations. Simultaneously, we claim that our products have

been tested and do not contain hazardous substances whose exceeding limits could have negative

impact on human health or natural environment

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self

installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices

during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN

PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE

PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE

PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF

EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

3

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDISPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQEUSTED TO FAMILIARIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO

USER-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE

PERSONNEL MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual

is necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6.

Usage of additional devices and components neither provided nor recommended by the producer

is forbidden;

7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,

damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions described in the

manual in question may change without further notice. We strongly suggest visiting the www.novuscctv.com

website in order to access the newest manual

Data included in the following user’s manual is up to date at the time of printing. AAT Holding Sp z o.o. holds

exclusive rights to modify this manual. The producer reserves the rights for device specification modification

and change in the design without prior notice.

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

4

TABLE OF CONTENTS

1. START-UP AND INITIAL IP CAMERA CONFIGURATION................................. 6

1.1. Overview .............................................................................................................. 6

1.2. Starting the IP camera .......................................................................................... 6

1.3. Initial configuration via the Web browser ........................................................... 7

2. NETWORK CONNECTION UTILIZING WEB BROSWER .................................. 8

2.1. Recommended PC specification for web browser ............................................... 8

2.2. Initial configuration via the Web browser ........................................................... 8

3. WWW INTERFACE - WORKING WITH IP CAMERA ........................................ 12

3.1. Displaying live pictures. .................................................................................... 12

3.2. Sensor Setting. ................................................................................................... 14

3.2.1. Description of Sensor Settings menu options ..................................... 14

3.3. Playback............................................................................................................. 20

3.4 Device Info..............................................................................................................

3.5. Stream Configuration......................................................................................... 21

3.6. Device Configuration ........................................................................................ 22

3.6.1. Local Network. ..................................................................................... 22

3.6.2. Device Port. .......................................................................................... 23

3.6.3 ADSL Network. .................................................................................... 24

3.6.4. Camera. ................................................................................................. 24

3.6.5. Data....................................................................................................... 25

3.6.6. OSD. ..................................................................................................... 26

3.6.7. Microphone........................................................................................... 27

3.6.8. Dome PTZ ............................................................................................ 28

3.6.9. BNC Output.......................................................................................... 28

3.6.10. System Configuration......................................................................... 28

3.7. External Devices. ............................................................................................... 28

3.8. Alarm Configuration.......................................................................................... 29

3.8.1. Alarm I/O............................................................................................... 29

3.8.2. Disk Alarm Linkage............................................................................... 30

3.8.3. Network Alarm. ..................................................................................... 30

3.8.4. I/O Alarm Linkage................................................................................. 31

3.8.5. Motion Alarm ........................................................................................ 32

3.9. Local Record...................................................................................................... 33

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

5

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

3.10. Privacy Masking. ............................................................................................. 34

3.11. Network Services............................................................................................. 35

3.11.1. PPPoE........................................................................................... 35

3.11.2. DDNS. .......................................................................................... 35

3.12. Service Center.................................................................................................. 36

3.12.1. Alarm Center. ............................................................................... 36

3.12.2. SMTP............................................................................................ 36

3.13. Privilege Manager............................................................................................ 37

3.13.1. Group............................................................................................ 37

3.13.2. User. ............................................................................................. 39

3.14. Protocol............................................................................................................ 41

3.14.1. Protocol Info................................................................................. 41

3.14.2. Security......................................................................................... 41

3.15. Device Log....................................................................................................... 42

3.15.1. Operation Log.............................................................................. 42

3.15.2. Alarm Log.................................................................................... 43

3.15.3. Collect Log. ................................................................................. 44

3.16. Maintenance..................................................................................................... 44

3.16.1. System Service............................................................................. 44

3.16.2. Device Restart.............................................................................. 45

3.16.3. Default Settings ........................................................................... 45

4. PTZ OPTIONS AVAILABLE THROUGH NMS SOFTWARE................................ 46

4.1 Preliminary information....................................................................................... 46

4.1.1. Preset. function ............................................................................. 46

4.1.2. Track function............................................................................... 47

4.1.3. Scan function. ............................................................................... 47

4.1.4. Tour function. ............................................................................... 48

4.1.5. Idle function.................................................................................. 48

4.1.6. Geographical orientation (North) function. ................................. 49

4.1.7. Timer function............................................................................... 49

5. ADDITIONAL INFORMATION ABOUT THE PRESET FUNCTION ................ 50

5.1 Preliminary information...................................................................................... 50

5.2 List of presets with special meanings ................................................................. 50

6. NOTES........................................................................................................................... 51

FOREWORD INFORMATION

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

6

1. START-UP AND INITIAL IP CAMERA CONFIGURATION

1.1. Overview

Following manual for IP Cameras NVIP-5000 series contains detailed information about camera

connection and operation, main page introduction, system related settings and camera settings.

Note

In this document you can find all available functionality present in described series of cameras.

Depending on camera model some features might be unavailable or unsupported.

1.2. Starting the IP camera

To run NOVUS IP camera you have to connect ethernet cable between camera and network switch and

you have to connect 24 VAC power adaptor, at least 50W.

Initialization process takes about 2 minutes. Then you can proceed to connect to the camera via web

browser.

The recommended way to start an IP camera and perform its configuration is connect directly to the

network switch which is not connected to other devices.

To obtain further information about network configuration parameters (IP address, gateway, network

mask, etc.) please contact your network administrator.

 Network connection using external power supply and network switch

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission

Network

transmission

Network Switch

Computer

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

7

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

 Network connection using external power supply, directly to the computer.

1.3. Initial configuration via the web browser

The default network settings for IP PTZ cameras 5000 series are :

1. IP address = 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to set PC IP address appropriately, so the two devices can

operate in one network subnet (e.g. for IP 192.168.1.1, appropriate address for the camera is from range

192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for

camera and PC computer

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission - cross over cable

Computer

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

8

2. NETWORK CONNECTION VIA WEB BROSWER

2.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming image display in 1920x1080

resolution and 30 fps speed.

1. CPU Intel Pentium IV 3 GHz or faster

2. RAM Memory min. 1 GB

3. VGA card (any displaying Direct 3D with min. 128 MB RAM memory)

4. OS Windows XP / VISTA / Windows 7 / Windows 8

5. Direct X version 9.0 or newer

6. Network card 10/100/1000 Mb/s

2.2. Connection with IP camera via web browser

You have to enter camera IP address in the web browser address bar. If IP address is correct user login

window will be displayed:

Default user is root and default password is pass.

In the Language box you can change the display language. The default language is English.

For safety reasons, it is recommended to change default user name and password.

It is possible to connect to the camera using Internet Explorer, Mozilla Firefox, Chrome or Opera

browsers. Running the IP camera in this browsers are very similar.

NETWORK CONNECTION VIA WEB BROWSER

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

9

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

If your computer has Flash Player

ins

t

a

ll

ed,

the main screen

for the

camera web interface

opens.

From

here you can view and configure

the

ca

m

e

ra

.

NOTE:

If your computer

does

not

have

Flash Player

ins

t

a

ll

ed,

you will be prompted

t

o

select if

y

o

u

would

like

t

o

use

Activ

eX

or Flash

Play

er

t

o

connect to the

ca

m

e

ra:



Click

here to shift playing life video with short delay widget! to

play

live

video

with

ActiveX

control

to

reduce

latency

(recommended): Uses

an

ActiveX

plug-in to connect to the camera. To

install the plug-in, click on the

video

area,

and

select Install

this

Add-on for all

users on this

computer

,

and follow the

prompts.

NOTE:

Please open the

Security settings

of IE browser, and enable the

Download unsigned

ActiveX controls.



Click

Please

download

the latest

version

of

Flash

Player to

play

live video:

Opens

a link to

download Flash Player from

Adobe’s

website.

After

completing the installation, restart your

browser and reconnect to

the

camera.

NOTE: When working in Windows Vista/7/8 the ActiveX applet may be blocked by Windows

Defender or User account control. In such case you should allow to run this applet, or simply disable

these functions.

NETWORK CONNECTION UTILIZING WEB BROWSER

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

10

NETWORK CONNECTION VIA WEB BROWSER

NOTE: If you are running Windows Vista/7/8 with Internet Explorer 11, the ActiveX applet can be

blocked through browser security settings. In this situation, you should: add the IP address of the ca-

mera to the view of compatibility (Tools -> Compatibility View Settings, click Add).

Then, in the security settings options, add the camera address to trusted sites and lower the security

level to a minimum.

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

11

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

NETWORK CONNECTION UTILIZING WEB BROWSER

After making the changes, restart the browser, re-connect to the camera and log on.

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

12

3. WWW INTERFACE - WORKING WITH IP CAMERA

3.1. Displaying live pictures

1.Camera settings

Live Video - Live video preview

Playback* - Playback records form SD card

Device Info - Device information

Stream Configuration - Video and audio settings for each stream

Device Configuration - Device configuration (e.g. Local Network, Date&Time)

External Device - External device configuration (function unavailable)

Alarm Configuration - Alarm Configuration (Motion alarm, Alarm I/O)

Local Record - Local Record Configuration

Privacy Masking - Privacy zones options

Network Service - Network services configuration (e.g. DDNS)

Service Center - Service center configuration (e.g. SMTP)

Privilege Manager - Users and groups management

Protocol - Protocols settings (e.g. ONVIF)

Device Log - Device Log contains: Operation Log, Alarm Log and Collect Log

Maintenance - Device Restart and restoring Default Settings

*This option is inactive

WWW INTERFACE - WORKING WITH IP CAMERA

3.

4.

1.

2.

5.

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

13

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

2. Video Parameter

Stream - Stream ID (choose one from available streams)

Bite Rate Type - Information about bit rate type

Bit Rate (kbps) - Information about bit rate

I Frame Interval - Information about I frame interval

Quality - Information about quality

3. PTZ Control Panel

PTZ Configure:

Preset - Programming, deleting, and recalling presets*

Track - Programming, deleting, and recalling tracks

Speed - Setting speed of movement

3D Position - Turn on/off control using the mouse

North - Setting orientation of the camera

Timer - Setting schedules

PTZ Control:

Arrow keys - Controlling the movement of the camera: up/down, right/left

„Home” key - Function unavailable

Zoom - Zoom control

Focus - Focus control

Iris - Function unavailable

Brush - Function unavailable

On/Off IR - Function unavailable

4. Menu bar

Change Password - Change users password

Sign Out - Logout from the camera menu and the option to change the menu

language

5. Video Control

Camera - Default number of the camera is 1.

Video - Turn on/off video

Audio - Turn on/off audio

Interphone - Turn on/off Interphone

NOTICE: Audio and Interphone functions will not be available when using Flash instead of ActiveX.

*- additional information about the presets are available on page 50

WWW INTERFACE - WORKING WITH IP CAMERA

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

14

3.2. Sensor Setting

Sensor Settings menu allows you to adjust the image settings and to control certain camera functions.

To access this menu, press the right mouse button on the video window in the Video Preview tab, and

then select Configure sensor.

To restore factory settings, press the default settings and confirm the operation. To revert to the last

saved settings, press the Reset button.

After each change the sensor settings, click Save to save your parameters. To exit the sensor

configuration without saving your settings, press the X button of the window.

3.2.1. Description of the option menu item: Sensor Settings

Change Settings

To make any changes to the sensor settings, switch to Debug Mode, visible in the lower left corner of

each window configuration. In addition, each sensor settings can be saved in one of the four available

configuration profiles. Any changes confirm the Save button.

Saving settings Whenever the window is closed Sensor Settings window appears informing us about

switching from edit mode in preview mode.

- Yes - Sensor Settings window closes, another

opens a window opens preview mode.

- No - Sensor Settings window closes, another

opens a window opens editing mode.

- Cancel - return to the Settings dialog Sensor.

Depending on the option selected more openly Sensor Settings window will run in debug mode or the

preview mode.

WWW INTERFACE - WORKING WITH IP CAMERA

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

15

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

Time Segment Tab

On the Time Segment we have the ability to configure, schedule of the camera by selecting the start and

end of the recording

- Start Time - select the hour (0-24) and minutes (0-50) in which the camera starts its work

- End Time - select the hour (0-24) then the minute in which the camera finishes its work.

Image Adjust Tab

On the Image Adjust setting you can adjust the brightness, color saturation, sharpness, contrast of the

image from the camera. Furthermore, it is possible to set the level of gamma correction and noise

reduction for color component.

WWW INTERFACE - WORKING WITH IP CAMERA

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

16

Image Setting Tab

- Image Settings - you can choose how the image rotation: Horizontal, Vertical, Flip

(simultaneous turning horizontally and vertically), and Off

- Still image - allows you to freeze the image.

Exposal Setting Tab

On the Exposal Setting tab, you can set the exposure mode of action of the automation of the camera:

- Auto - Where the camera automatically adjusts to the lighting conditions on the limit list to

strengthen you can also select the maximum amplification level

- Manual - where the user selects the shutter speed value (in the range of 1/25 to 1/10000), the

aperture (in the range of F1.6 to F14) and the reinforcement (0 to 30dB) and its limit.

- Shutter Priority - where you can manually set the shutter speed (between 1/25 to 1/10000) and

limit gain, and the camera automatically adjusts the aperture value

- Aperture Priority - where you can manually set the aperture value (ranging from F1.6 to F14)

and limit gain, and the camera will automatically adjust the shutter value

In addition, the ability to enable or disable the DSS which the maximum value is 1 second.

WWW INTERFACE - WORKING WITH IP CAMERA

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

17

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

WB Setting Tab

On the WB Setting can be set up the way you work automation WB:

- Inside - option dedicated while the camcorder is inside the room

- Outdoors - dedicated option when the camera is running outdoor

- Triggered one button - option inactive

- ATW - Automation option when the camera adjusts the white balance to the currently observed

area

- Manual - user set level off R (0 to 255) and B (0 to 255)

- Fluorescent light - optional dedicated to work by the light of fluorescent lamps

- Sodium lamps - the option is dedicated to work by the light of sodium lamps

D/N Setting Tab

On the D/N Setting can choose whether the camera is in automatic mode, day mode, night mode or

using the scheduler.

- In Auto mode - the camera will automatically adjust the mode to lighting conditions.

- In Day Mode - forces the camera in color.

- The Night Mode - forces the camera in black/white.

- In the Scheduler - user you can decide what time the camera switches from day mode to night

and from night mode to day mode.

WWW INTERFACE - WORKING WITH IP CAMERA

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

18

Infrared Tab

On the Infrared, you can control how the IR illumination works:

- In Auto mode - the camera automatically adjusts the lighting power IR LEDs, depending on the

size of the optical zoom and external conditions.

- In Manual mode - power IR illuminator can be set by the user independently for each of the

three groups of IR LEDs (near, middle and far).

Lens Setting Tab

On the Lens Setting, we can set the following parameters:

- DZoom - Enable or disable the digital zoom option (12x).

- Focus Mode - choose the type of work focusing mechanism: Auto - the camera itself sharpens

the image, depending on the observed area, Manual - in this mode, the user selects when to

sharpen the image using Auto Focus Once button now, PUSH - after camera focused on one

area, it wont focus on new objects, that appear in focused zone.

- AF Sensitivity - choose the sensitivity of focus. Possible options: high, medium, low.

- Focus Near Limit - we can set the limit of the camera zooms to the selected distance of 1.5m,

2m, 3m, 6m, 10m and infinity.

WWW INTERFACE - WORKING WITH IP CAMERA

IP PTZ cameras NVIP-5000 series - user manual ver.1.0.

19

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

NR Tab

In Noise Reduction tab, we can set three modes:

- Auto - the camera decides to include noise correction 3DNR. Additionally, you can divide the

maximum level of compensation.

- Manual - manually adjust the level (default 50) digital noise reduction.

- Off - mode, digital noise reduction is turned off.

Special Function Tab

In Special Function Tab, you can set the camera:

- WDR - enables or disables the WDR (Wide Dynamic Range)

-Anti Fog - feature improved visibility in bad weather (fog rain)

- BLC - rear backgrounds compensation function that eliminates the effect resulting from

observing the area with too strong light source in the background.

- HLC - the ability to enable or disable the HLC, which reduces the brightness of the areas

observed by the camera in order to provide better image quality.

WWW INTERFACE - WORKING WITH IP CAMERA

NVIP-5000 series IP PTZ camera - user manual ver.1.0.

20

3.3 Playback - option not available

3.4. Device Info

Device Info menu allows user to view information about camera and change the device name.

In DEVICE NAME box, you can type your own name for the camera. To set your own name, enter it in

this field, previously deleting the default name, and press the SET button.

WWW INTERFACE - WORKING WITH IP CAMERA

Strona jest ładowana ...

Novus NVIP-3SD-8200/30 Instrukcja obsługi

Novus NVIP-3SD-8200/30 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty