Vermeiren V200 XL Instrukcja obsługi

VERMEIREN

V200 XL

I N S T R U C T I O N M A N U A L

M O

D E D ’ E M P L O I

G E B R U I K S A A N W I J Z I N G

G E B R A U C H S A N W E I S U N G

I S T R U Z I O N I P E R L ' U S O

MANU A L D E I N S T R U C C I ON E S

I N S T R U K C J A O B S Ł U G I

N Á V O D K O B S L U Z E

All r

ights reserved, including translation.

No part of this manual may be reproduced in any form

what so ever (print, photocopy, microfilm or any other

process) without written permission of the publisher, or

processed, duplicated or distributed by using electronic

systems.

Aucune partie de ce manuel ne peut être reproduite,

sous quelque forme que ce soit (imprimée, photocopie,

microfilm ou tout autre procédé) sans l'autorisation écrite

du publicateur, ni traitée, dupliquée ou distribuée à l'aide

de systèmes électroniques.

Alle rechten, inclusief vertaling, voorbehouden.

Niets uit deze handleiding mag geheel of gedeeltelijk in

enige vorm (druk, fotokopie, microfilm of ieder ander

procedé) zonder de schriftelijke toelating van de uitgever

worden gereproduceerd of met behulp van elektronische

systemen worden verwerkt, gekopieerd of verspreid.

Alle Rechte, auch an der Übersetzung, vorbehalten.

Kein Teil der Gebrauchsanweisung darf in irgendeiner

Form (Druck, Fotokopie, Mikrofilm oder einem anderen

Verfahren) ohne schriftliche Genehmigung des

Herausgebers reproduziert oder unter Verwendung

elektronischer Systeme verarbeitet, vervielfältigt oder

verbreitet werden.

Il presente manuale non può essere riprodotto, neppure

parzialmente, con alcun mezzo (stampa, fotocopia,

microfilm o altro procedimento) senza l’autorizzazione

scritta della casa produttrice, né elaborato, duplicato o

distribuito con l’ausilio di sistemi elettronici.

traducción.

Se prohíbe la reproducción total o parcial del presente

manual de cualquier forma (impresión, fotocopia,

microfilm o cualquier otro procedimiento), así como la

edición, copia o distribución empleando sistemas

electrónicos, sin el permiso escrito del editor.

Wszelkie prawa zastrzeżone, łącznie z

tłumaczeniem.

Żadna część niniejszej instrukcji nie może być

powielana w jakiejkolwiek formie (drukowanej, fotokopii,

mikrofilmu ani innej) bez pisemnej zgody wydawcy, nie

może być również przetwarzana, kopiowana ani

rozprowadzana za pomocą systemów elektronicznych.

Všechna práva vyhrazena, včetně překladu.

Šíření jakékoliv části tohoto katalogu jakýmkoliv

způsobem (tisk, kopie, mikrofilm nebo jiný způsob) bez

písemného souhlasu vydavatele, nebo zpracování,

duplikace či distribuce prostřednictvím elektronických

systémů je zakázáno.

EN

Instructions for specialist dealer

This instruction manual is part and parcel

of the product and must accompany every

product sold.

Version: A, 2012-02

FR

Instructions pour les distributeurs

Ce manuel d'instructions fait partie du

produit et doit accompagner chaque

produit vendu.

Version : A, 2012-02

NL

Instructies voor de vakhandelaar

Deze handleiding is deel van het product

en dient bij iedere product te worden

geleverd.

Versie: A, 2012-02

DE

Hinweise für den Fachhändler

Diese Gebrauchsanweisung ist Bestand-

teil des Produkts und ist bei jeder

Produkts auszuhändigen.

Version: A, 2012-02

IT

Istruzioni per il rivenditore

Il presente Manuale di istruzioni è parte

integrante del prodotto e deve essere

fornito assieme alla prodotto.

Versione: A, 2012-02

ES

Instrucciones destinadas a los distri-

buidores especializados

El presente manual de instrucciones es

parte integrante del producto y se debe

adjuntar a todas las producto que se

vendan.

Versión: A, 2012-02

PL

Instrukcje dla wyspecjalizowanego

sprzedawcy

Niniejsza instrukcja obsługi jest

nieodłączną częścią produktu i musi być

dołączona do każdego sprzedawanego

produktu.

Wersja: A, 2012-02

CS

Pokyny pro specializovaného prodejce

Tento návod k obsluze je součástí

dodávky a musí být součástí každého

prodaného produktu.

Verze: A, 2019-06

Multi version: B, 2019-06

V200 XL

2012-02

ͳ

Contents

Preface ................................................................................................. 2

1 Productdescription .................................................................. 3

1.1 Intended Use ................................................................................................................ 3

1.2 Technical specifications .............................................................................................. 4

1.3 Drawing ....................................................................................................................... 5

1.4 Accessories .................................................................................................................. 6

1.5 Location identification plate ........................................................................................ 6

1.6 Explanation of symbols ............................................................................................... 6

2 Use ............................................................................................. 6

2.1 Carrying the wheelchair .............................................................................................. 6

2.2 Mounting the rear wheels ............................................................................................ 7

2.3 Unfolding the wheelchair ............................................................................................ 7

2.4 Mounting or removing of push bar ............................................................................. 7

2.5 Mounting or removing of the footrests ....................................................................... 8

2.6 Operating the brakes .................................................................................................... 8

2.7 Mounting or removing of arm supports ...................................................................... 9

2.8 Transfer in and out the wheelchair ............................................................................ 10

2.9 Correct position in the wheelchair ............................................................................ 10

2.10 Riding the wheelchair ................................................................................................ 10

2.11 Moving on slopes ...................................................................................................... 11

2.12 Negotiating steps or curbs ......................................................................................... 11

2.13 Fold up the wheelchair .............................................................................................. 13

2.14 Taking off the wheels ................................................................................................ 13

2.15 Transport in the car .................................................................................................... 13

3 Installation and adjustment .................................................. 14

3.1 Tools .......................................................................................................................... 14

3.2 Manner of delivery .................................................................................................... 14

3.3 Adjusting the seat height and seat angle ................................................................... 14

3.4 Adjust the brakes ....................................................................................................... 17

3.5 Adjusting of the footrests .......................................................................................... 17

3.6 Adjusting the arm support ......................................................................................... 18

4 Maintenance ........................................................................... 19

4.1 Regular Maintenance ................................................................................................. 19

4.2 Shipping and storage ................................................................................................. 19

4.3 Care ........................................................................................................................... 20

4.4 Inspection .................................................................................................................. 20

4.5 Disinfection ............................................................................................................... 21

5 Guarantee ............................................................................... 23

6 Disposal ................................................................................... 23

7 Declaration of conformity ..................................................... 23

8 Maintenance plan .................................................................. 24

9 Disinfection book ................................................................... 24

V200 XL

2012-02

ʹ

Preface

First of all we want to thank you for putting your trust in us by selecting one of our

wheelchairs.

The Vermeiren wheelchairs are the result of many years of research and experience. During

the development, special attention was given to the ease of use and the serviceability of the

wheelchair.

The expected lifetime of 8 years for your wheelchair is strongly influenced by the care and

maintenance of the wheelchair.

This manual will help you get acquainted with the operation of your wheelchair.

Following the user instructions and the maintenance instructions are an essential part of the

guarantee.

This manual reflects the latest product developments. Vermeiren has the right to introduce

changes without the obligation to adapt or replace previously delivered models.

For any further questions, please consult your specialist dealer.

V200 XL

2012-02

͵

1 Productdescription

1.1 Intended Use

The wheelchair is intended for people with walking difficulties or no walking abilities.

The wheelchair is designed to transport 1 person.

The wheelchair is suited for indoor and outdoor use.

The user can propel the wheelchair by himself or have the wheelchair pushed by an

attendant.

The different types of fittings and accessories, and the modular construction allow full use by

persons disabled by:

• paralysis

• loss of limbs (leg amputation)

• limb defects or deformations

• stiff or damaged joints

• heart insuffiencies and poor blood circulation

• balance disturbances

• cachexia (decrease in muscle)

• and also for aged persons.

When providing for individual requirements:

• body size and weight (max. 170kg)

• physical and psychological condition

• residential circumstances

• environment

should be taken into consideration.

Your wheelchair should only be used on surfaces where all four wheels are touching the

ground and where there is sufficient contact to propel the wheels equally.

You should practice for use on uneven surfaces (cobblestones, etc.), slopes, curves and to

get past obstacles (curbs, etc.).

The wheelchair should not be used as a ladder, nor is it a transport for heavy or hot objects.

When used on mats, carpeted floors or loose floor coverings, the floor covering can get

damaged.

Use only Vermeiren approved accessories.

The manufacturer is not liable for damage caused by the lack of or improper service or as a

result of not following instructions from this manual.

Compliance with the user and maintenance instructions are an essential part of the

guarantee conditions.

V200 XL

2012-02

Ͷ

1.2 Technical specifications

Technical terms below are valid for the wheelchair in standard settings.

If other footrest / arm support or other accessories are used, the tabulated values will

change.

Make

Vermeiren

Address

Vermeirenplein 1/15, B

-

2920

Kalmthout

Type

Manual wheelchair

Model

V200 XL

Maximum occupant mass

170 kg

Description

Dimensions

Effective seat width 530 mm 560 mm 600 mm

Overall width (depends on the seat width) 740 mm 770 mm 810 mm

Description

Dimensions Minimum

Dimensions

Maximum

Overall length with legrest 1050 mm

Folded length 1050 m

Folded width 385 mm

Folded height 820 mm 1000 mm

Total mass 20,15 kg

Mass of heaviest part 12,25 kg

Masses of parts that can be dismantled or

removed

Foot supports:

1,75 kg;

Arm supports: 1,80 kg; Rear wheels: 4,05 kg

Static stability downhill 6,5°

Static stability uphill 5,5°

Static stability sideways 18°

Obstacle climbing 60 mm

Seat plane angle 0° 10°

Effective seat depth 490 mm

Seat surface height at front edge 440 mm 530 mm

Backrest angle 0° 10°

Backrest height 400 mm

Distance between footrest and seat 430 mm

Angle between seat and footrest 5° 25°

Distance between armrest and seat 220 mm 240 mm

Front location of armrest structure 410 mm

Handrim diameter 535 mm

Horizontal location of axle (deflection) -40 mm 34 mm

Minimum turning radius 1620 mm

Diameter Krypton PU Rear wheels 22" 24"

Tyre pressure, rear (driving) wheels Max. 3.5 bar

Diameter Krypton PU steering wheels 200 mm

Tyre pressure, steering wheels Max. 2.5 bar

Storage and use temperature + 5 °C + 41 °C

Storage and use humidity 30% 70%

We reserve the right to introduce technical changes. Measurement tolerance

±

15 mm / 1,5 kg / °

Table 1: Technical specifications

V200 XL

2012-02

ͷ

The wheelchair complies to the requirements set up in:

ISO 7176-8: Requirements and test methods for static, impact and fatigue strengths.

ISO 7176-16: Resistance to ignition of upholstered parts

1.3 Drawing

1 = Armrests

2 = Arm supports

3 = Footrest

4 = Brakes

5 = Steering wheels (front wheels)

6 = Driving wheels (rear wheels)

7 = Seat

8 = Back

9 = Tip cap

10 = Cross

11 = Handles

12 = Push bar

V200 XL

2012-02

͸

1.4 Accessories

The following accessories are available for the V200 XL:

• Anterior pelvic belt (B20) for mounting on the tubes of the back (see according

manual)

• Anti-tipping device (B78) for mounting on the bottom frame (see according manual).

1.5 Location identification plate

1.6 Explanation of symbols

Maximum mass

I

ndoor and outdoor use

Down slope

Up slope

CE conformity

Not crash-tested

2 Use

This chapter describes the everyday use. These instructions are for the user and the

specialist dealer.

The wheelchair is delivered fully assembled by your specialist dealer. The instructions

intended for the specialist dealer on how to set up the wheelchair are given in § 3.

2.1 Carrying the wheelchair

The best way to carry the wheelchair is to make use

of the wheels and roll the wheelchair.

If this is not possible (e.g. when the rear wheels are taken off for transportation in a car),

firmly grasp the frame on the front and the grips. Do not use the foot or arm rests or the

wheels to grasp the wheelchair.

1 = Logo Vermeiren

2 = Not crash-tested

3 = Identification plate

4 = Name Vermeiren

V200 XL

2012-02

͹

2.2 Mounting the rear wheels

1. Take the rear wheel and push on button c.

2. Keep the button pushed in and mount the rear

wheels axle till it stops.

3. Release the button.

4. Check that the wheels is secured.

2.3 Unfolding the wheelchair







 CAUTION: Risk of clamping – Keep fingers away from moving parts of the

wheelchair.

1. Position yourself behind the wheelchair.

2. Use the hand-grips to open the wheelchair as much as possible.

3. Position yourself at the front of the wheelchair.

4. Push both seating tubes down till they are fixed in their position.

5. Mount the push bar to the right hand-grip (standing behind the wheelchair)

2.4 Mounting or removing of push bar

The mounting of the push bar is done as follows:

1. Mount the push bar with the star button in

the left hand-grip.

2. Swing the push bar to the right.

3. Mount clip c over the right hand-grip d.

When this is difficult it is possible the push

bar is too long. Place the push bar on the

left-hand-grip with the star button in hole d.

To take off the Push bar:

1. Loosen the star button on the right hand-

grip.

2. Remove clip c from the right hand-grip d.

V200 XL

2012-02

ͺ

2.5 Mounting or removing of the footrests

The mounting of the footrest is done as

follows:

1. Hold the footrest sideways at the outside

of the wheelchairs frame and mount the

tube hood c into the frame.

2. Swing the footrest inwards till it clicks in

position.

3. Swing the foot plate downwards until the

clips e lock over pen f

To take off the footrests:

1. Make clip e loose from pen f.

2. Swing the footplate upwards.

3. Pull handle

d.

4. Swing the footrest to the outside of the

wheelchair till it comes loose from the

guidance.

5. Pull the footrest from tube hood c.

2.6 Operating the brakes









WARNING: The brakes are not used to slow down the wheelchair during

movements – Use the brake only to prevent the wheelchair from unintended

movements.









WARNING: Good operation of the brakes is influenced by wear and

contamination of the tires (water, oil, mud, …) – Check the condition of the tires

before each use.







WARNING: The brakes are adjustable and can wear – Check the operation of the

brakes before each use.

To apply the brakes:

1. Push the brake handles forward till you feel a distinctive click.









 CAUTION: Risk of unintended movement – Make sure the wheelchair is on a

flat horizontal surface before releasing the brakes. Never release both brakes

simultaneously.

To release the brakes:

1. Release one brake by pulling the handle backwards.

2. Hold the hand-rim of the release wheel with your hand.

3. Release the second brake by pulling the handle backwards.

V200 XL

2012-02

ͻ

2.7 Mounting or removing of arm supports

The arm supports of the wheelchair can be mounted by following instructions.









CAUTION: Risk of clamping – Keep fingers, buckles and clothes away from the

bottom side of the arm support.

1. Mount the rear tube of the arm rest in tube

hood c.

2. Make sure the arm support clicks in the

locking mechanism.

3. Fold the arm rest forward.

4. Click the front tube of the arm rest in tube

hood

d.

To open and remove the arm rest:

1. Press lever

d and pull the front of the arm rest

upwards.

2. Fold the arm rest backwards.

V200 XL

2012-02

ͳͲ

3. To remove the arm rest, press button e and pull the rear of the arm support from

tube hood f.

2.8 Transfer in and out the wheelchair







CAUTION: In case you cannot perform the transfer in a safe manner, ask

someone to assist you.





CAUTION: Risk of tipping over of the wheelchair – Do not stand on the foot plate.

1. Position the wheelchair as close as possible to

the chair, couch or bed to/from you wish to

transfer.

2. Check both brakes from the wheelchair are in

the on position.

3. Fold the foot plate upwards to prevent

standing on them.

4. If the transfer is on the side of the wheelchair,

fold the arm support on that side upwards.

(see § 2.7)

5. Transfer to/from the wheelchair.

2.9 Correct position in the wheelchair

Some recommendations for a comfortable use of the wh

eelchair:

• Position your backside as close as possible to the back rest.

• Make sure your upper legs are horizontal – If needed adjust the length of the foot

rests. (see § 3.5)

2.10 Riding the wheelchair









WARNING: Risk of clamping – Prevent your fingers from being caught by the

wheels spokes.









WARNING: Risk of clamping – Be careful passing through restricted passages

(e.g. doors).







WARNING: Risk of burns – Be careful when driving in hot or cold environments

(sunshine, extreme cold, saunas, etc.) for a sufficient amount of time and when

touching - Surfaces can assume the environment temperatures.

V200 XL

2012-02

ͳͳ

1. Release the brakes.

2. Take both hand rims at their highest position.

3. Lean forward and push the hand rims forward until straight arms.

4. Swing your arms loosely back to the hand rims topside and repeat the movement.

2.11 Moving on slopes









WARNING: Control your speed – Moving on slopes as slow as possible.









WARNING: Consider the capacities of your attendant – If your attendant does not

have enough force to control the wheelchair, put on the brakes.









WARNING: Risk of tipping over – Lean forward to move your centre of gravity

forward. To improve a better stability.

1. If available on the wheelchair, wear the safety belt.

2. Do not attempt moving on too high slopes. The maximum

slope angles (upwards and downwards) are mentioned in

table 1.

3. Ask an attendant to help you moving on the slope.

4. Lean forward to move your centre of gravity forward.

2.12 Negotiating steps or curbs

2

.12.1 Getting down steps or curbs

Riding down low curbs can be done moving forwards. Make sure that the foot rests do not

touch the ground.

A practiced user can negotiate small steps or curbs by himself:









 WARNING: Risk of tipping over – If you do not have

enough experience with your wheelchair, ask

assistance of an attendant.

1. Bring balance on the rear wheels to reduce the pressure on

the front wheels.

2. Negotiate the curbs.

Higher curbs can be taken forward with an attendant:

1. Ask the attendant to tip the wheelchair slightly backwards.

2. Get past the curbs while moving on the rear wheels.

3. Put the wheelchair back on the four wheels.

An experienced user can negotiate higher curbs by himself. This is

best done backwards.

1. Turn the wheelchair to have the rear wheels facing the

curb.

2. Lean forward to move your centre of gravity forward.

3. Move the wheelchair close to the curbs.

4. Use the hand rim to roll-off wheelchair from the curb in a

controlled manner.

V200 XL

2012-02

ͳʹ

2.12.2 Moving up steps or curbs

Moving up steps or curbs with attendant as follows:

1. Prevent the foot rests from touching the curb.

2. Ask the attendant to tip the wheelchair backwards, just

enough to move the front wheels over the curb.

3. Lean backwards to move your centre of gravity above the rear

wheel.

4. Place the front wheels on the curb.

5. Roll rear wheels of the wheelchair over the curb.

Higher curbs are negotiated backwards:

1. Turn the wheelchair to have the rear wheels facing the curb.

2. Lean backwards and move your centre of gravity above the rear wheels.

3. Ask the attendant to pull the wheelchair on the curb.

4. Take back the normal position in the wheelchair.

An experienced user can negotiate curbs by himself:







WARNING: Risk of tipping over – If you have not enough experience to control

the wheelchair, get help from an attendant.

1. Drive until the curbs.

2. Ensure that the footrest don't touch the curbs.

3. Lean backwards so you are balancing on the rear wheels.

4. Role the front wheels balancing over the curbs.

5. Bend forwards for more stability.

6. Role the rear wheels over the curbs.

2.12.3 Taking of stairs

Taking of stairs while you staying in the wheelchair

shall be according following rules:









WARNING: Risk of tipping over – Taking of stairs shall always with 2 attendants.

1. Remove the footrests.

2. One attendant tip the wheelchair slightly backwards.

3. The second attendant take the front of the frame.

4. Stay calm, avoid sudden movements and keep your arms inside the wheelchair.

5. Take the steps on the rear wheels of the wheelchair.

6. Mounting the footrests back after taking the stair.

V200 XL

2012-02

ͳ͵

2.13 Fold up the wheelchair









 CAUTION: Chance of pinching – Do not place fingers between the components

of the wheelchair.

1. Fold or remove the footplates (see § 2.5).

2. Swing the push bar away from the right hand-grip (standing behind the wheelchair).

3. Take the seat on the front side and backside and pull it up.

2.14 Taking off the wheels

To facilitate the transport off the wheelchair the rear wheels can be taken off:

1. Make sure the brakes standing in the off

position.

2. Take the wheelchair to the side frame where

you want to remove the wheel.

3. Press the button

c in the center of the wheel

hub.

4. Pull the wheel away from the frame.

2.15 Transport in the car









DANGER: Risk of injury – The wheelchair is not suited for use as a seat in a

motor vehicle.







WARNING: Risk of injury – See that the wheelchair is attached properly. So you

can avoid injury from the passengers during collision or sudden braking.









WARNING: Risk of injury – Use for attaching the wheelchair and passenger

NEVER the same seatbelt.

Never use your wheelchair as a seat in an automobile or other vehicle. The wheelchair shall

be marked with following symbol.

To transport the wheelchair in the car use following steps:

1. Remove footrests and accessories.

2. Store footrests and accessories safely.

3. If possible, fold the wheelchair and remove the wheels.

4. Place the wheelchair in the luggage place.

5. If the wheelchair and the passenger compartment is NOT separated, attach the

frame of the wheelchair securely to the vehicle. You can use the available safety

belts in the vehicle.

V200 XL

2012-02

ͳͶ

3 Installation and adjustment

The instructions in this chapter are for the specialist dealer.

The Vermeiren V200 XL has been designed to be adjust with a minimum of replacements

parts. There is no need for extra stock of spare parts.

To find a service facility or specialist dealer near you, contact the nearest Vermeiren facility.

A list of Vermeiren facilities can be found on the last page.









WARNING: Risk of unsafe settings - Use only the settings described in this

manual.









WARNING: Variation of allowed adjustments can still change the stability of your

wheelchair (tilt back or sideways).

3.1 Tools

To set up the wheelchair the following tools are nee

ded.

• Wrench set n° 7 to n° 22

• Allen keyset n° 3 to n° 8

• Screwdriver n° 4 to n° 5

• Screwdriver Phillips head

3.2 Manner of delivery

The Vermeiren V200 XL shall be delivered with:

• 1 frame with arm supports, rear and front wheels (standard delivery

• seat height: 500 mm, seat angle: 5°)

• 1 footrest

• Tools

• Manual

• Accessories

3.3 Adjusting the seat height and seat angle

The Vermeiren V200 XL is adjustable in 4 seat height

s and 5 seat angles (0°-2,5°-5°-7,5°-

10°) by changing the position of the wheels for each height and angle there is a different

setting of the front and rear wheels.

The summary of the different seat heights by a standard seat angle 5° is tabulated below.

Seat height Rear wheels Front wheels

Hole

Position axle plate !

!!

!

Hole

Bushing "

""

"#

##

#relative to

castor

stem housing $

$$

$

440 mm

f

Above

c

Above

470 mm

c

Under

c

Under

500 mm

(Standard)

e

Under

d

Under

530 mm

g

Under

e

Under

Table 2: Seat heights by seat angle 5°

V200 XL

2012-02

ͳͷ

Front wheel

Axle plate rear wheels

Seat height 440 mm

Seat height 470 mm

Seat height 500 mm (standard)

Seat height 530 mm

V200 XL

2012-02

ͳ͸

Change the seat height according the following steps:

1. Remove the rear wheels (see § 2.14).

2. Screw the axle bushings of the rear wheels from the axle plate !.

3. Assemble the axle bushings in the right hole of the axle plate, see Table 2 and

previous figure.

4. Check if the axle bushings are fastened well.

5. Screw the swivel axles %#of the front wheels loose.

6. Place the front wheels in the right hole of the front fork (table 2).

7. Place the bushings according table 2.

8. Install the swivel axles %#of the front wheels and tighten them. Check the tension in

the swivel axle % so it turn smoothly, but there is no space for motion.

9. Mount the rear wheels.

10. If installed properly the swivel axles of the front wheels and the ground must be

perpendicular. Check this.

11. Adjust the brakes according § 3.4.

For other seat angle and seat height combinations, the above procedure can be used to

adjust the front fork and axle plate in the right combination.

If you don't find the right combination you can always contact the company Vermeiren.

Check that the swivel axles are perpendicular to the ground. If necessary use the procedure

below to adjust the castor stem housing:#

1. Loosen the 3 bolts using a size 5 Allen key.

2. Adjust the castor stem housing to the desired angle.

3. Tighten the 3 bolts.

Bolts

Castor

stem

housing

Indication 5 angle

positions (triangle)

V200 XL

2012-02

ͳ͹

3.4 Adjust the brakes





 WARNING: Risk of injury – Brakes may only be adjusted by your specialist

dealer.

Adjust the brakes according following rules:

1. Install the wheels according § 2.2.

2. Disconnect the brakes by pulling lever c

backwards.

3. Loosen the bolts

d so the brake

mechanism can slide over the guide

e.

4. Pull the brake mechanism over the guide e to

the desired position.

5. Retighten the bolts d.

6. Check working of the brakes.

7. If necessary repeat the above steps until the

brakes are adjusted well.

3.5 Adjusting of the footrests

3.5.1 Length of the footrests



 CAUTION: Risk of damage – Avoid that the footrests make any contact with the

ground. Keep a minimum distance from 60 mm (2.36 in.) above the ground.

Adjust the length of the footrests as follow:

1. Remove the screw c (on the back of the

footrests).

2. Adjust the length of the footrest to a comfortable

length.

3. Tighten the screw cproperly.

The max

adjustable

length of the

footrest shall

be marked with

a triangle on

the tube.

2

3

V200 XL

2012-02

ͳͺ

3.5.2 Adjusting angle foot plate

Adjust the angle of the foot plate as follow:

1

. Loosen bolt c.

2. Adjust tube d in the desired angle. The angle indication (80°-85 °-90°-95°-100°) is

according the dashes e.

3. Retighten the bolt c.

3.6 Adjusting the arm support

The arm support of your wheelchair can be adjustable in height and depth. The height of the

arm support can be adjusted in 3 positions.

Height armsupport to seat Number of the blocks

under the tube

Number of blocks between

tube and armrests

220 mm (8.66 in.) (Standard) 2 1

230 mm (9.06 in.) 1 2

240 mm (9.45 in.) 0 3

Table 3: Height of arm support

The depth of the armrest can be adjusted in 3 positions.

Depth of the armrest Used holes

Front position Back and middle

Middle position (Standard) Hole 2 and 4

Back position Front and middle

Table 4: Depth of armrest

Strona jest ładowana ...

Vermeiren V200 XL Instrukcja obsługi

Vermeiren V200 XL Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty