ESAB MobileFeed 301 AVS Instrukcja obsługi

Typ
Instrukcja obsługi
0558 012 634 20150918 Valid for: serial no. WxxK533xxxx
MobileFeed 301 AVS
GB Instruction manual
SE Bruksanvisning
DE Betriebsanweisung
FR Manuel d'instructions
ES Instrucciones de uso
GR Οδηγίες χρήσεως
IT Istruzioni per l'uso
RO Manual de instrucţiuni
PT Manual de instruções
SK Navod na pouitie
NL Gebruiksaanwijzing
DK Brugsanvisning
NO Bruksanvisning
FI Käyttöohjeet
PL Instrukcja obsługi
HU Kezelési utasítások
CZ Návod k používání
EE Kasutusjuhend
LV Lietošanas pamācība
SI Priročnik z navodili
LT Naudojimo instrukcija
BG Ръководство за експлоатация
HR Priručnik s uputama
TABLE OF CONTENTS
0558 012 634 © ESAB AB 2015
ENGLISH GB ............................................................................................................. 4
SVENSKA ................................................................................................................ 25
DEUTSCH ................................................................................................................ 46
FRANÇAIS ............................................................................................................... 70
ESPAÑOL ................................................................................................................. 92
ΕΛΛΗΝΙΚΑ ............................................................................................................. 116
ITALIANO ............................................................................................................... 140
ROMÂNĂ ................................................................................................................ 163
PORTUGUÊS ......................................................................................................... 185
SLOVAKI ................................................................................................................ 207
NEDERLANDS ....................................................................................................... 228
DANSK ................................................................................................................... 250
NORSK ................................................................................................................... 271
SUOMI .................................................................................................................... 292
POLSKI .................................................................................................................. 313
MAGYAR ................................................................................................................ 336
ČESKY ................................................................................................................... 357
EESTI ..................................................................................................................... 378
LATVIEŠU VALODĀ ............................................................................................... 398
SLOVENIJA ............................................................................................................ 419
LIETUVIŲK ............................................................................................................. 440
БЪЛГАРСКИ .......................................................................................................... 461
HRVATSKI .............................................................................................................. 485
TABLE OF CONTENTS
0558 012 634 © ESAB AB 2015
1 SAFETY ................................................................................................................ 5
1.1 Overview ...............................................................................................................5
2 INTRODUCTION...................................................................................................7
2.1 Overview ...............................................................................................................7
2.2 Equipment.............................................................................................................7
3 TECHNICAL DATA ...............................................................................................8
4 INSTALLATION.....................................................................................................9
4.1 Recieving and handling.......................................................................................9
4.2 Selection of drive rolls and guide tubes ............................................................9
4.3 Installing drive rolls and guide tubes...............................................................10
4.4 Installing the welding wire ................................................................................10
4.5 Threading the welding wire............................................................................... 11
4.6 Adjusting the brake drag................................................................................... 11
4.7 Torch connection ...............................................................................................12
4.8 Supply connections ...........................................................................................13
5 OPERATION ....................................................................................................... 14
5.1 Overview .............................................................................................................14
5.2 Connections and control devices.....................................................................15
5.3 Operating procedures........................................................................................18
5.3.1 Operating safety precautions ...........................................................................18
5.3.2 Setting a welding procedure.............................................................................20
5.3.3 Weld data table ................................................................................................20
5.3.4 MobileFeed 301 with CC Power Sources ........................................................21
5.3.5 MobileFeed 301 with CV Power Sources.........................................................21
5.3.6 Shutdown .........................................................................................................22
6 MAINTENANCE..................................................................................................22
6.1 Inspection and service ......................................................................................22
6.2 Wire feeder..........................................................................................................23
6.3 Solenoid valve replacement..............................................................................23
6.4 Troubleshooting.................................................................................................23
7 ORDERING SPARE PARTS...............................................................................24
WIRING DIAGRAM..................................................................................................506
WEAR PARTS..........................................................................................................507
ORDERING NUMBERS...........................................................................................508
ACCESSORIES .......................................................................................................509
Rights reserved to alter specifications without notice.
1 SAFETY
0558 012 634
- 5 -
© ESAB AB 2015
1 SAFETY
1.1 Overview
MEANING OF SYMBOLS
As used throughout this manual: Means Attention! Be Alert!
DANGER!
Means immediate hazards which, if not avoided, will result in immediate,
serious personal injury or loss of life.
WARNING!
Means potential hazards which could result in personal injury or loss of
life.
CAUTION!
Means hazards which could result in minor personal injury.
WARNING!
Read and understand the instruction manual before
installing or operating.
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed in addition to the standard regulations that apply to
the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations which can
result in injury to the operator and damage to the equipment.
1. Anyone who uses the equipment must be familiar with:
its operation
location of emergency stops
its function
relevant safety precautions
welding and cutting or other applicable operation of the equipment
2. The operator must ensure that:
no unauthorised person is stationed within the working area of the equipment when it
is started up
no-one is unprotected when the arc is struck or work is started with the equipment
3. The workplace must:
be suitable for the purpose
be free from drafts
1 SAFETY
0558 012 634
- 6 -
© ESAB AB 2015
4. Personal safety equipment:
Always wear recommended personal safety equipment, such as safety glasses,
flame-proof clothing, safety gloves
Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could
become trapped or cause burns
5. General precautions:
Make sure the return cable is connected securely
Work on high voltage equipment may only be carried out by a qualified electrician
Appropriate fire extinquishing equipment must be clearly marked and close at hand
Lubrication and maintenance must not be carried out on the equipment during
operation
WARNING!
Arc welding and cutting can be injurious to yourself and others. Take precautions
when welding and cutting. Ask for your employer's safety practices which should
be based on manufacturers' hazard data.
ELECTRIC SHOCK - Can kill
Install and earth the unit in accordance with applicable standards
Do not touch live electrical parts or electrodes with bare skin, wet gloves or
wet clothing
Insulate yourself from earth and the workpiece
Ensure your working stance is safe
FUMES AND GASES - Can be dangerous to health
Keep your head out of the fumes
Use ventilation, extraction at the arc, or both, to take fumes and gases away
from your breathing zone and the general area
ARC RAYS - Can injure eyes and burn skin.
Protect your eyes and body. Use the correct welding screen and filter lens and
wear protective clothing
Protect bystanders with suitable screens or curtains
FIRE HAZARD
Sparks (spatter) can cause fire. Make sure therefore that there are no
inflammable materials nearby
NOISE - Excessive noise can damage hearing
Protect your ears. Use earmuffs or other hearing protection. Protect your ears.
Use earmuffs or other hearing protection
Warn bystanders of the risk
MALFUNCTION - Call for expert assistance in the event of malfunction.
Read and understand the instruction manual before installing or operating.
PROTECT YOURSELF AND OTHERS!
CAUTION!
This product is solely intended for arc welding.
2 INTRODUCTION
0558 012 634
- 7 -
© ESAB AB 2015
CAUTION!
Class A equipment is not intended for use in residential
locations where the electrical power is provided by the
public low-voltage supply system. There may be potential
difficulties in ensuring electromagnetic compatibility of
class A equipment in those locations, due to conducted
as well as radiated disturbances.
NOTE!
Dispose of electronic equipment at the recycling
facility!
In observance of European Directive 2012/19/EC on
Waste Electrical and Electronic Equipment and its
implementation in accordance with national law, electrical
and/or electronic equipment that has reached the end of
its life must be disposed of at a recycling facility.
As the person responsible for the equipment, it is your
responsibility to obtain information on approved collection
stations.
For further information contact the nearest ESAB dealer.
ESAB can provide you with all necessary welding protection and accessories.
2 INTRODUCTION
2.1 Overview
The MobileFeed 301 AVS (Arc Voltage Sensing) is a portable wire feeder. The unit is
powered entirely on the arc voltage from a constant current (CC) or constant voltage (CV)
welding power source. It operates with reversed polarity, Direct Current Electrode Positive
(DCEP), or straight polarity, Direct Current Electrode Negative (DCEN). The MobileFeed 301
AVS is available with two connections, EURO and TWECO. A remote option is available with
the Warrior power source (requires software update to the power source).
The unit is designed for use with hard, soft, and cored electrodes (gas shielded or
self-shielded) from 0.030” (0.8mm) through 5/64” (1.98mm) diameter with a wire feed speed
from 50 to 750 in/min (1.3 - 19.0 m/min). The feeder components are totally enclosed in a
rugged case.
ESAB's accessories for the product can be found in the "ACCESSORIES" chapter of
this manual.
2.2 Equipment
The MobileFeed 301 AVS is supplied with:
Instruction manual
Voltage pickup cable with clamp
3 TECHNICAL DATA
0558 012 634
- 8 -
© ESAB AB 2015
3 TECHNICAL DATA
NOTE!
The MobileFeed 301 AVS is not recommended for short circuiting transfer using
constant current power sources due to the limited short circuit current available
on constant current power sources.
MobileFeed 301 AVS
Wire feed speed 50 750 in/min (1.3 19.0 m/min)
Primary input (open circuit voltage or arc voltage) Not for use with AC power
Minimum 14 V DC
Welding 45 V DC (when welding)
Maximum 100 V DC (113 V peak)
Standard spindle hub 2” (50 mm) ID
Standard spool 8” (200 mm) OD, 12" (300 mm) OD
Maximum welding current 320 A at 60 % duty cycle
250 A at 100 % duty cycle
Maximum gas inlet pressure 75 psi (5.2 Bar)
Wire diameters
Hard .030” (0.8 mm), .035” (0.9 mm),
.045” (1.2 mm), .052” (1.4 mm),
1/16” (1.6 mm)
Soft .035” (0.9 mm), 3/64” (1.2 mm),
1/16” (1.6 mm)
Cored .030” (0.8 mm), .035” (0.9 mm),
.045” (1.2 mm), .052” (1.4mm),
1/16” (1.6 mm), 5/64” (2.0 mm)
Motor type DC permanent magnet pre-lubricated, enclosed
Brake type (wire) Drag
Control Solid state
Feed system Push
On-Off switch Standard
Ramp start Standard
Height × Width × Length 17.0" × 8.3" × 21.0" (432×210×534mm)
Weight (with contactor, without spool) 33 lbs (15 kg)
Enclosure class IP23S
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration
by solid objects or water.
Equipment marked IP 23S is intended for indoor and outdoor use; however, should not be
operated in precipitation.
4 INSTALLATION
0558 012 634
- 9 -
© ESAB AB 2015
4 INSTALLATION
4.1 Recieving and handling
Before installing this equipment, clean all packing material from around the unit and carefully
inspect for any damage that may have occurred during shipment. Any claims for loss or
damage that may have occurred in transit must be filed by the purchaser with the carrier. A
copy of the bill of lading and freight bill will be furnished by the carrier on request if occasion
to file claim arises.
WARNING!
Secure the equipment -
particularly if the ground is
uneven or sloping.
If the unit is unstable in upright position (A), as when the torch or spool is disconnected or
when there is a risk that the unit might be pulled by the torch during operation, the unit must
be secured. Alternatively it can be operated in horizontal position (B) if conditions permit.
4.2 Selection of drive rolls and guide tubes
WARNING!
When the wire feeder is connected to the power source, the work lead from the
power source is connected to the work piece and the power source is energized,
closing the torch trigger will cause the welding wire to become electrically hot and
will cause the drive rolls to turn. Keep fingers clear!
The drive rolls have two grooves. The unit is supplied ready to feed 0.045”, .052” or 1/16”
(1.2 to 1.6 mm) diameter cored wires or .035” - .045” (0.9 - 1.2 mm) hard wires depending on
the part number ordered.
Other drive rolls are available to feed other sizes of hard wire, soft wire, and cored wire. See
Drive Roll and Guide Tube Selection Chart in the WEAR PARTS chapter.
Two lower drive rolls are required for four roll drive systems.
4 INSTALLATION
0558 012 634
- 10 -
© ESAB AB 2015
4.3 Installing drive rolls and guide tubes
CAUTION!
Turn off the power source and the wire feeder.
1. Release the pressure roll assembly lever (1) and lift the pressure roll assembly (2) up.
2. Remove the knurled screw (3) while holding the drive roll (4).
3. Check and install the correct guide tubes.
4. Keep or replace the drive roll (4) with the required size, the designation is marked on the
side of the roll facing out.
5. Put the knurled screw (3) back in position on the drive roll (4) and tighten it.
6. Thread the wire and fasten the pressure roll assembly (2).
4.4 Installing the welding wire
CAUTION!
Turn off the power source and the wire feeder.
4 INSTALLATION
0558 012 634
- 11 -
© ESAB AB 2015
1. Remove the spool retainer nut (1).
2. Put the wire spool (2) on the hub to rotate counterclockwise as the wire is unwounded.
The hub pin must engage the hole in the wire spool.
3. Install the spool retainer nut (1).
4.5 Threading the welding wire
CAUTION!
Before threading the wire, make sure the chisel point and burrs have been
removed from the end of the wire to prevent the wire from jamming in the torch
liner.
1. Turn off the power source and the wire feeder.
2. Release the pressure roll assembly lever and lift the pressure roll assembly up.
3. Check that the drive roll, groove position and wire guides are correct.
4. Feed the wire from the spool through the inlet guide along the drive roll goove and into
the outlet guide tube.
5. Lower the pressure roll assembly and adjust the drive roll pressure to make sure that
there is no wire slippage, but not too tight to create excess pressure.
6. Turn on the power source and the wire feeder.
7. Push the torch trigger switch or operate the jog switch to feed wire through the torch.
4.6 Adjusting the brake drag
CAUTION!
Turn off the power source and the wire feeder.
4 INSTALLATION
0558 012 634
- 12 -
© ESAB AB 2015
Brake disc friction should provide enough drag to keep the wire spool from spinning freely
after the wire feed stops.
The brake hub is adjusted when delivered, if adjustment is required, follow the instructions
below. Adjust the brake hub so that wire is slightly slack when wire feed stops.
1. To increase the braking torque, use an 5/16" (8 mm) allen key and turn the drag
adjusting screw (1) clockwise.
2. To reduce the braking torque, use an 5/16" (8 mm) allen key and turn the drag adjusting
screw (1) counterclockwise.
4.7 Torch connection
CAUTION!
Make sure the chosen torch has the correct rating for the welding current to be
used, has the correct size and type of liner and has the correct contact tip and
guide tube.
WARNING!
Turn off the power to the welding power source and the wire feeder before
making any connections between the wire feeder and the welding power source.
The torch adaptor on the MobileFeed connects directly to the wire feeder wire drive
assembly, power and shielding gas supply.
1. Line up the torch connector with the wire feeder adaptor and push on firmly.
2. Hand tighten the locking collar on the Euro connector.
4 INSTALLATION
0558 012 634
- 13 -
© ESAB AB 2015
4.8 Supply connections
CAUTION!
Turn off the power source and the wire feeder.
The MobileFeed 301 AVS can be used with either DC Electrode Positive (DCEP) or DC
Electrode Negative (DCEN) polarity without modifications.
1. Connect the welding cable (1) from the power source to the weld cable lug connection
extending from the rear of the MobileFeed 301 AVS feeder.
a) Positive terminal for gas shielded flux cored or solid wires.
b) Negative terminal for most gasless self-shielded cored wires.
WARNING!
Make sure that the welding cables are correctly insulated before applying
power to the power source. Uninsulated cable and parts can arc when
contacting a grounded surface. The arc may damage eyes or start a fire.
Body contact with an uninsulated weld cable connector, or uncovered
conductor can cause shock and severe injury, possibly fatally.
2. Connect a second welding cable (2) between the opposite polarity output connection on
the power source and the work piece.
3. Connect the wire feeder work lead/voltage pick-up cable clip (3) to the work piece.
4. If gas shielded wire is used, connect the inlet gas hose to the gas inlet connections on
the rear of the feeder.
5. Make sure that all hose and cable connections are tight.
5 OPERATION
0558 012 634
- 14 -
© ESAB AB 2015
6. Turn on the power source and close the contactor if the power source is equipped with
an output contactor control switch. Open circuit voltage must be present to operate the
wire feeder.
7. Turn the wire feeder power switch to "ON".
8. Check all gas connections for leaks.
WARNING!
Unless starting to weld, do not allow the welding wire to touch a grounded
metal surface. The welding wire becomes electrically hot when the secondary
contactor is closed. Keep fingers clear of the drive rolls; they will start turning
when the torch trigger is pressed.
9. If gas shielded wires are used, adjust the gas flow meter to the desired flow rate by
closing the torch trigger switch or operating the gas purge switch.
10. Turn off the power source and the wire feeder when they are not in use.
5 OPERATION
5.1 Overview
General safety regulations for handling the equipment can be found in the "SAFETY"
chapter of this manual. Read it through before you start using the equipment!
WARNING!
Electric shock! Do not touch the workpiece or the welding head during operation!
NOTE!
When moving the equipment, use handle intended for transportation. Never pull
the equipment by the welding torch.
CAUTION!
Before threading the wire, make sure the chisel point and burrs have been
removed from the end of the wire to prevent the wire from jamming in the torch
liner.
5 OPERATION
0558 012 634
- 15 -
© ESAB AB 2015
WARNING!
Rotating parts can cause injury, take great care.
WARNING!
Risk of crushing when replacing the wire bobbin! Do not use safety gloves when
inserting the welding wire between the feed rollers.
WARNING!
Do not operate the feeder with the enclosure open.
5.2 Connections and control devices
1. Knob for setting the wire
feed speed
5. Display for wire feed
speed/voltage
9. Shield gas connection
2. Knob for setting the
voltage
6. Trigger lock switch 10. Welding cable
connection
3. Torch connection 7. Power switch 11. Power source remote
voltage control
connection
4. Work lead (Voltage
pick-up)
8. Torch switch connector
(TWECO/NAS versions
only)
5 OPERATION
0558 012 634
- 16 -
© ESAB AB 2015
Wire feed speed (Arc voltage control)
The wire feed speed is controlled by the knob for wire feed speed on the front of the wire
feeder.
When the wire feeder is connected to a constant voltage (CV) type of power source, the knob
for wire feed speed controls the welding current. Turning the knob clockwise increases the
welding current; turning it counterclockwise decreases the welding current.
When the wire feeder is connected to a constant current (CC) type of power source, the knob
for wire feed speed controls the arc voltage. Turning the knob clockwise decreases the arc
voltage; turning it counterclockwise increases the arc voltage. The actual wire feed speed for
any given setting varies with the arc voltage. Increasing the arc voltage causes an increase
in the wire feed speed.
When the CV/CC switch inside the MobileFeed, is set to CV, the “preset” wire feed speed will
be shown on the display. The wire speed will not vary with changes in the arc voltage.
When the CV/CC switch is set to CC, the wire feed speed and voltage will be shown on the
display. The wire speed shown is the speed that will result from the displayed voltage.
Adjusting the knob for voltage affects the wire feed speed. For example, if the display shows
300 in/min and 20 V, an adjustment of the voltage to 24 V will result in an increase to
approximately 365 in/min. A change in arc voltage of 4 V will result in a change in wire speed
of 65 in/min. For a step by step guide to setting wire speed and voltage see the section
“Setting a Welding Procedure”.
Voltage
In CC mode the knob for setting the voltage is used to adjust the voltage which in turn affects
the wire feed speed. See the "Wire feed speed" description above.
The knob for setting the voltage can also be used to set the power source output voltage
when the MobileFeed is set to CV with the remote voltage control option and a Warrior power
source is being used. The power source voltage is then read on the MobileFeed display for
wire feed speed and voltage.
Display for wire feed speed and voltage
The digital display shows the wire feed speed (in/min or m/min) and voltage. It also enables
the welder to preset wire feed speed and power source voltage.
Trigger lock switch
The trigger lock function is a variation of 4 stroke operation. If the trigger lock function is
turned on, the torch trigger can be released once the arc is established, the power
source/feeder will continue to weld until the trigger is pressed and released again, or the arc
established signal is lost by manually breaking the arc. The trigger will not be locked unless
the arc is established before the trigger is released.
Power switch
The power switch (0/I) on the front of the wire feeder starts the wire feeder when the feeder
is connected to the power source and the work piece. The power source must be turned on
with the contactor closed.
5 OPERATION
0558 012 634
- 17 -
© ESAB AB 2015
1. Main fuse, 10 A 3. Jog/purge switch
2. Circuit breaker, 7 A 4. CC/CV switch
Circuit breaker, 7 A
This resettable 7 A circuit breaker, in series with motor armature, protects the control board
from damage if the motor is stalled.
Jog/Purge switch
JOG is used when you need to feed the wire without welding voltage being applied. The wire
is fed at the set speed for as long as the switch is pushed.
PURGE is used when measuring the gas flow or to flush any air or moisture from the gas
hoses before welding starts. The gas flows as long as the switch is pushed. There is no need
for welding voltage or wire feed start.
If the wire has been threaded through torch and contact tip, simply operate the jog button or
cut off wire, as required, so that the wire extends about 1/2” beyond the end of the torch
nozzle.
CC/CV switch
The CC/CV switch is used to set CC or CV mode. CC mode is used for constant current
power sources. CV mode for constant voltage power sources. The selected mode also has
impact on the functions of the wire feeder as shown below:
Mode Display Knob for setting the wire feed speed
CC Wire feed speed and arc voltage
shown
Controls the arc voltage / Wire speed
feed increase with increased voltage
CV Wire feed speed shown Controls the welding current
5 OPERATION
0558 012 634
- 18 -
© ESAB AB 2015
Dip switch settings
The DIP switches are located on the Digital Display PCB inside the MobileFeed.
NOTE!
To locate the Digital Display PCB it is necessary to remove the cover that
protects the electronic parts of the MobileFeed.
Check the setting of the dip switches on the Digital Display PCB. These switches can be set
up for the display to show the wire feed speed in in/min or in m/min.
The setting (1) for the display is in/min. The setting (2) for the display is m/min.
5.3 Operating procedures
5.3.1 Operating safety precautions
Comply with all ventilation, fire and other safety requirements for arc welding as established
in the section "SAFETY PRECAUTIONS".
1. Because of the radiant energy of the welding arc and the possibility of drawing an arc
before the helmet is lowered over the face, the operator should wear flash goggles with
filter lenses under his helmet. The helmet filter plate should be shade number 11
(nonferrous) or 12 (ferrous). All those viewing the arc should use helmets with filter
plates, as well as flash goggles. Nearby personnel should wear flash goggles.
2. The radiant energy of the arc can decompose chlorinated solvent vapors, such as
trichloroethane and perchlorethylene, to form phosgene, even when these vapors are
present in low concentrations. DO NOT weld where chlorinated solvents are present in
atmospheres in or around the arc.
3. DO NOT touch the electrode, contact tip or metal parts when power is ON: all are
electrically energized (HOT) and can cause a possibly fatal shock. DO NOT allow
electrode to touch grounded metal. It will create an arc flash that can injure eyes. It may
also start a fire or cause other damage.
5 OPERATION
0558 012 634
- 19 -
© ESAB AB 2015
4. When working in a confined space, be sure it is safe to enter. The confined space should
be tested for adequate oxygen (at least 19%) with an approved oxygen measuring
instrument. The confined space should not contain toxic concentrations of fumes or
gases. If this cannot be determined, the operator should wear an approved air supplied
breathing apparatus. Avoid gas leaks in a confined space, as the leaked gas can
dangerously reduce oxygen concentration in the breathing air. DO NOT bring gas
cylinders into confined spaces. When leaving a confined space, shut OFF gas supply at
the source to prevent gas from leaking into the space. Check the breathing atmosphere
in the confined space to be sure it is safe to reenter.
5. Never operate the equipment at currents greater than the rated ampere capacity.
Overheating will occur.
6. Never operate equipment in a damp or wet area without suitable insulation for protection
against shock. Keep hands, feet and clothing dry at all times.
7. Whenever the equipment is left unattended, turn OFF all control power, power supply
switches and gas supplies. Open the main line switch.
8. Wear dark substantial clothing to protect exposed skin from arc burn, sparks and flying
hot metal.
9. Turn off welding power before adjusting or replacing electrodes.
WARNING!
When the power switch is ON and the torch trigger is pushed, the electrode wire
becomes electrically hot and the wire feed rolls are activated. Do not touch the
wire as it may cause a possibly fatal shock. Unless welding, do not allow the wire
to touch a grunded metal surface as it will cause an arc flash. Keep clear of feed
rolls and drive gears.
WARNING!
Prior to welding, it is imperative that the correct protective clothing (welding coat
and gloves) and eye protection (glasses and welding helmet) are put on. Failure
to comply may reult in serious injury.
CAUTION!
Do not terminate the arc by removing the torch from the weld area. Release the
torch trigger to stop welding before removing the torch.
WARNING!
Failure to turn off shield gas in confined space may result in a build-up of fumes,
displacing oxygen.
5 OPERATION
0558 012 634
- 20 -
© ESAB AB 2015
5.3.2 Setting a welding procedure
Quick set-up procedure
1. For Constant Voltage (CV) Power Source; Set the desired arc voltage on the power
source.
2. For Constant Current (CC) Power Source; Set the desired weld current on the power
source.
3. On the MobileFeed unit: Set the desired wire feed speed with the knob for the wire feed
speed and use the values shown by the display as guidance.
A feeder in CV mode will show the actual wire feed speed while welding.
A feeder in CC mode will show a wire feed speed that varies with changes in arc voltage.
When not welding, the display will show what the wire feed speed will be at the displayed
voltage.
5.3.3 Weld data table
The voltage (V) and current (A) values presented in the tables below are the arc voltage and
the weld current. Values of current (A) that may flow through the wire feeder may not be
higher than rated values of the unit.
Flux Core E70T-1 & 2
Diameter
Wire Feed Speed
(inch/min) / (m/min)
150 /
3.8
200 /
5.1
250 /
6.35
300 /
7.6
350 /
8.9
400 /
10.2
450 /
11.4
500 /
12.7
600 /
15.2
.045” 29 V
150 A
29 V
210 A
30 V
250 A
33 V
290 A
34 V
330 A
.052” 25 V
155 A
30 V
300 A
1/16” 27 V
190 A
30 V
300 A
33 V
365 A
33 V
410 A
Metal Core
Diameter
Wire Feed Speed
(inch/min) / (m/min)
200 / 5.1 250 / 6.35 300 / 7.6 350 / 8.9 400 / 10.2 450 / 11.4 500 / 12.7
.045” 28 V
250 A
29 V
260 A
30 V
270 A
32 V
300 A
32 V
350 A
.052” 29 V
275 A
29 V
300 A
30 V
325 A
1/16” 30 V
300 V
30 V
350 A
32 V
400 A
Steel Solid Wire
Diameter
Wire Feed Speed
(inch/min) / (m/min)
200 /
5.1
250 /
6.35
300 /
7.6
350 /
8.9
400 /
10.2
450 /
11.4
500 /
12.7
550 /
14.0
600 /
15.2
.035” 25 V
180 A
25 V
200 A
26 V
215 A
27 V
230 A
28 V
245 A
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374
  • Page 375 375
  • Page 376 376
  • Page 377 377
  • Page 378 378
  • Page 379 379
  • Page 380 380
  • Page 381 381
  • Page 382 382
  • Page 383 383
  • Page 384 384
  • Page 385 385
  • Page 386 386
  • Page 387 387
  • Page 388 388
  • Page 389 389
  • Page 390 390
  • Page 391 391
  • Page 392 392
  • Page 393 393
  • Page 394 394
  • Page 395 395
  • Page 396 396
  • Page 397 397
  • Page 398 398
  • Page 399 399
  • Page 400 400
  • Page 401 401
  • Page 402 402
  • Page 403 403
  • Page 404 404
  • Page 405 405
  • Page 406 406
  • Page 407 407
  • Page 408 408
  • Page 409 409
  • Page 410 410
  • Page 411 411
  • Page 412 412
  • Page 413 413
  • Page 414 414
  • Page 415 415
  • Page 416 416
  • Page 417 417
  • Page 418 418
  • Page 419 419
  • Page 420 420
  • Page 421 421
  • Page 422 422
  • Page 423 423
  • Page 424 424
  • Page 425 425
  • Page 426 426
  • Page 427 427
  • Page 428 428
  • Page 429 429
  • Page 430 430
  • Page 431 431
  • Page 432 432
  • Page 433 433
  • Page 434 434
  • Page 435 435
  • Page 436 436
  • Page 437 437
  • Page 438 438
  • Page 439 439
  • Page 440 440
  • Page 441 441
  • Page 442 442
  • Page 443 443
  • Page 444 444
  • Page 445 445
  • Page 446 446
  • Page 447 447
  • Page 448 448
  • Page 449 449
  • Page 450 450
  • Page 451 451
  • Page 452 452
  • Page 453 453
  • Page 454 454
  • Page 455 455
  • Page 456 456
  • Page 457 457
  • Page 458 458
  • Page 459 459
  • Page 460 460
  • Page 461 461
  • Page 462 462
  • Page 463 463
  • Page 464 464
  • Page 465 465
  • Page 466 466
  • Page 467 467
  • Page 468 468
  • Page 469 469
  • Page 470 470
  • Page 471 471
  • Page 472 472
  • Page 473 473
  • Page 474 474
  • Page 475 475
  • Page 476 476
  • Page 477 477
  • Page 478 478
  • Page 479 479
  • Page 480 480
  • Page 481 481
  • Page 482 482
  • Page 483 483
  • Page 484 484
  • Page 485 485
  • Page 486 486
  • Page 487 487
  • Page 488 488
  • Page 489 489
  • Page 490 490
  • Page 491 491
  • Page 492 492
  • Page 493 493
  • Page 494 494
  • Page 495 495
  • Page 496 496
  • Page 497 497
  • Page 498 498
  • Page 499 499
  • Page 500 500
  • Page 501 501
  • Page 502 502
  • Page 503 503
  • Page 504 504
  • Page 505 505
  • Page 506 506
  • Page 507 507
  • Page 508 508
  • Page 509 509
  • Page 510 510

ESAB MobileFeed 301 AVS Instrukcja obsługi

Typ
Instrukcja obsługi