AAT NVR-4532-H4/F Instrukcja obsługi

User’ s manua l

(shor t )

NVR-4532-H4/F

NVR-4532-H4/F User’s manual (short) ver.1.0

2

INFORMACJE

IMPORTANT SAFEGUARDS AND WARNINGS

THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING DIRECTIVES:

DIRECTIVE 2014/35/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 26 February 2014 on the harmonisation

of the laws of the Member States relating to the making available on the mar-

ket of electrical equipment designed for use within certain voltage limits.

DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIMENT

AND OF THE COUNCIL of 26 February 2014 on the harmonisation

of the laws of the Member States relating to electromagnetic compatibility

(OJ L 96, 29.3.2014, p. 79–106, with changes)

DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 4 July 2012 on waste electrical and electronic

equipment (WEEE) (OJ L 197, 24.7.2012, p. 38–71,with changes)

DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 8 June 2011 on the restriction of the use

of certain hazardous substances in electrical and electronic equipment

(OJ L 174, 1.7.2011, p. 88–110, with changes)

NVR-4532-H4/F User’s manual (short) ver.1.0

3

SAFETY REQUIREMENTS

ATTENTION!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT PROVISIONED FOR THE

GIVEN PRODUCT IN ITS USER’S MANUAL AVAILABLE AT WWW.NOVUSCCTV.COM

AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR THAT ARISES

FROM THE NORMAL APPLICATION OF THE PRODUCT, ITS MANUFACTURER MUST

BE CONTACTED OR THE RESPONSIBILITY OF THE MANUFACTURER FOR THE

RESULTS OF SUCH AN ACTION SHELL BE EXCLUDED.

1. Prior to undertaking any action please consult the following manual and read all the safety and

operating instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual

is necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the

user’s manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is

forbidden;

7. You are not allowed to use the device in high humidity environment (i.e. close to swimming pools,

bath tubs, damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.)

is not recommended since it may lead to heat build-up and damaging the device itself as a

consequence;

9. Mounting the device on unstable surface or using not recommended mounts is forbidden.

Improperly mounted device may cause a fatal accident or may be seriously damaged itself. The

device must be mounted by qualified personnel with proper authorization, in accordance with this

user’s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with

those specified by the producer in the devices technical datasheet. Therefore, it is forbidden to

supply the devices from a power sources with unknown parameters, unstable or not meeting

producer’s requirements;

11. You cannot allow any metal objects get inside the recorder. It might cause serious damage. If a

metal object gets inside the device contact the authorised Novus service immediately.

12. The manufacturer does not bear responsibility for damage or loss of data stored on HDDs or other

media occurred during the usage of the product.

Due to the product being constantly enhanced and optimized, certain parameters and functions

described in the manual in question may change without further notice.

We strongly suggest visiting the www.novuscctv.com website in order to access the newest

manual .

NOVUS NVRs are dedicated to work with NOVUS cameras. Using only NOVUS products

guarantees the highest image quality. Connecting cameras from other manufacturers to NOVUS

NVRs may decrease video quality.

Technical changes reserved without prior notice and printing errors possible.

NVR-4532-H4/F User’s manual (short) ver.1.0

4

FOREWORD INFORMATION

1. FOREWORD INFORMATION

1.1. Main characteristics

• Network Video Recorders

• Recording resolution up to 3840 x 2160

• H.264, H.264+, H.265, H.265+ compression

• Dual stream recording

• Support 4 x SATA 3,5” HDDs *

• Operating system based on Linux

• Main monitor 1 x HDMI (4K UltraHD), 1 x VGA (FullHD)

• Spot monitor available on VGA output with defined cameras, sequence

• Support fisheye cameras

• 2 independent 10/100/1000Mbps ports

• Intelligent video analysis (Exception, Tripwire, Zone entrance, Abandoned Object, Object

Disappearance, Face Detection, Pedestrian Detection, Cross Counting, Face Recognition, Sound

detection, Perimeter Intrusion Detection by pedestrian or vehicle, Line Cross Detection by

pedestrian or vehicle ) **

• Backup: onto HDD or USB Flash Memory through USB port and through the IP network

• Software: NHDR-5000 Viewer (application for remote administration, live monitoring and recorded

data search )

• RXcamView application for live and playback functions from mobile devices

• User friendly multi-lingual OSD

• IR remote controller and PC mouse included

* List of compatible HDD models and maximum capacities is available on Novus Security website in

the Compatible Disk file in the product tab.

** Functions depend on connected camera model.

NVR-4532-H4/F User’s manual (short) ver.1.0

5

1.2. Recorders’ technical data

*** Display and playback speeds are achieved using dual stream.

FOREWORD INFORMATION

Video

IP Cameras up to 32 channels at 3840 x 2160 resolution (video + audio)

Supported Resolution

max. 3840 x 2160

max. 3000 x 3000 for fisheye cameras

Compression H.264, H.264+, H.265, H.265+

Monitor Output

main (split screen, full screen, sequence): 1 x VGA, 1 x HDMI (4K

UltraHD) (up to 2 monitors simultaneously)

spot: 1 x VGA (FullHD)

Dualstreaming Support yes

Fisheye Support yes, 4000 IP series cameras

Audio

Audio Output 1 x line-out (RCA) 1 x HDMI

Recording

Recording Speed 960 fps (32 x 30 fps for 3840 x 2160 and lower)

Stream Size 320 Mb/s in total from all cameras

Recording Mode

time-lapse, triggered by: manual, alarm input, motion detection, face

recognition, intelligent image analysis functions, PIR alarm

Prealarm/Postalarm up to 3 s/up to 600 s

Display

Display Speed 960 fps (32 x 30 fps) ***

Playback

Playback Speed 480 fps (16 x 30 fps) ***

Recorded Data Search

by date/time, events, image analysis events, motion in a defined area,

related to face recognition, tags

Backup

Backup Methods DVD (option), USB port (HDD or Flash memory), network

Backup File Format JPEG, BMP, PNG, MP4, AVI, RF

Storage

Internal storage available mount: 4 x HDD 3.5” 14 TB SATA *

Total Internal Capacity 56 TB

External storage 1 x eSATA

Total External Capacity 32 TB

Alarm

System Reaction to Alarm

Events

buzzer, e-mail, alarm output activation, screen message, recording

activation, PTZ, Full Screen, FTP picture upload, FTP video upload,

picture to Cloud, video to Cloud

Intelligent image analysis

Supported functions

Exception, Tripwire, Zone entrance, Abandoned Object, Object

Disappearance, Face Detection, Pedestrian Detection, Cross Counting,

Face Recognition, Sound detection, Perimeter Intrusion Detection by

pedestrian or vehicle, Line Cross Detection by pedestrian or vehicle

NVR-4532-H4/F User’s manual (short) ver.1.0

6

FOREWORD INFORMATION

Intelligent image analysis, PTZ control, dualstream mode, motion detection, alarm inputs / outputs

functions depends on the functionality of the camera and the capabilities of the communication

protocol. The recorder is dedicated to work with Novus 4000 series IP cameras and achieves the best

functionality with them. Detailed data can be found in the compatibility table available on Novus

Security website in the DOWNLOADABLE FILES tab in the product tab.

1.3. Package contents

Unpack the device carefully. After unpacking, ensure that package contains the following items:

• Network Video Recorder

• Power supply 100 ~ 240 VAC/12 VDC PSU

• Power cord

• USB Mouse

• IR remote controller

• User’s manual (short)

If any of the elements has been damaged during transport, pack all the elements back into the original

packaging and contact your supplier.

Network

Network Interface 2 x Ethernet - RJ-45 interface, 10/100/1000 Mbit/s

Network Protocols Support

HTTP, TCP/IP, IPv4/v6, HTTPS, FTP, DHCP, DNS, DDNS, NTP, RTSP,

UPnP, SNMP, PPPoE, SMTP, P2P

PC/MAC Software NMS, Internet Explorer, NHDR-5000 Viewer/NHDR-5000 Viewer

Smartphone Software RxCamView (iPhone, Android)

Number of Simultaneous

Connections

up to 96 clients

Bandwidth 320 Mb/s in total to all client workstations

PTZ

PTZ Functions pan/tilt/zoom, preset commands, patterns

Auxiliary Interfaces

USB Ports 1 x USB 3.0, 2 x USB 2.0

Operating system

Operating System Linux

OSD languages: Polish, English, others

Control PC mouse and IR remote controller (in-set included), network

System Diagnostic automatic control of: HDDs, network, camera connection loss

Security password protection, IP filtering

Installation parameters

Dimensions (mm) 378 (W) x 66 (H) x 326 (D)

Weight 2.5 kg (without HDD)

Power Supply 12 VDC (100 ~ 240 VAC/12 VDC PSU in-set included)

Power Consumption 60 W (with 4 HDDs)

Operating Temperature -10°C ~ 45°C

NVR-4532-H4/F User’s manual (short) ver.1.0

7

2. STARTING THE DEVICE

2.1. Electrical connection and other rear panel elements.

1. POWER DC: Power supply connector for 12V adapter.

2. POWER SW: Power switch.

3. AUDIO OUT: Audio output for connecting speakers and amplifier (RCA connector).

4. AUDIO IN: Audio mono inputs (RCA LINE IN type) for connecting microphone. Allows

intercom connection between the recorder and the client station. The connection is

initiated from the client software or browser. Sound is not recorded.

5. VGA: VGA main monitor connector, use the D-SUB VGA cable to connect monitor.

6. HDMI: HDMI main monitor connector, use the HDMI cable to connect monitor.

7. USB: USB port for external Flash memory, mouse connection and other USB

compatible devices.

8. WAN: RJ-45 ethernet port to connect local network and Internet (by router).

9. LAN: RJ-45 ethernet port to connect a switch with IP cameras.

10. ALARM IN: Alarm input terminal.

11. ALARM OUT: Alarm output, relay.

12. RS: RS-485 bus connector to connect PTZ cameras.

13. E-SATA: E-SATA connector for NV-5000EST-H4 HDD matrix.

2.2. HDD’s mounting

Note:

In order to obtain info on latest compatible HDDs together with their capacities, please contact

your distributor or visit www.novuscctv.com website. AAT SYSTEMY BEZPIECZEŃSTWA Sp.

z o.o. company does not bear responsibility for any issues arising from usage of unsupported SD

cards/HDDs.

List of compatible HDDs contains all disks supported by a given NVR model, including desktop

HDDs. However due to the fact that image recording prefers reliability usage of 24x7 recording

HDDs is therefore advised.

If a disk was used in another device, formatting becomes necessary. Please take it into account

due to the irrecoverable data loss resulting from said process.

STARTING THE DEVICE

1

2

5

6

7

4

3

8

9

10

11

12

13

NVR-4532-H4/F User’s manual (short) ver.1.0

8

NVR-4532-H4/F supports 4 x 3,5" SATA HDD. Follow the instruction to mount the HDD’s. Photos

are illustrative, may differ slightly from the described recorder.

Before staring the process make sure the power supply is not connected.

In order to mount HDD’s, unscrew 3 screws on the back as depicted below and remove top cover.

The picture below shows the places where the drives can be mounted.

STARTING THE DEVICE

screws

NVR-4532-H4/F User’s manual (short) ver.1.0

9

Unscrew the HDDs mountings as shown on picture below. Each pair allow to screw two HDDs.

Screw the HDDs to mountings. Then screw the mountings to the base. SATA and power cables are

attached to the mainboard. Connect them to HDDs. Repeat the procedure with the second mountings

and HDDs.

When the disks are connected correctly, put on the cover and screw it back.

STARTING THE DEVICE

NVR-4532-H4/F User’s manual (short) ver.1.0

10

2.3. Connecting the power supply

Please connect provided power supply in the rear power port of the NVR.

To start the unit turn on the power switch on back panel. Initialization lasts approximately 120 seconds.

During this time executing any device functions and pressing any buttons is prohibited. To shut down

the device please use the menu.

WARNING!

Make connection when the power is not applied and the power switch is turned off.

Do not place the power cord under the carpet or rug. The power cord is usually earth-grounded.

However, even if it's not earth-grounded, never modify it on your own for earth-grounding.

Make sure that power adapter is placed near of NVR and secured from accidental disconnection.

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

2.4. Connecting monitor

NVRs support following interfaces for main monitor: HDMI, VGA.

For HDMI following resolutions are supported: 1024x768, 1280x1024, 1440x900, 1280x720,

1920x1080, 2560x1440, 3840x2160. VGA supports resolution up to 1920x1080.

2.5. Connecting ethernet and IP cameras

The NVR-4532-H4/F recorder has two 10/100/1000 Mbps connectors to connect cameras via a switch

or router. Each of the connectors works in a different addressing.

It is recommended to connect the cameras to a switch in a separate network. The switch should be

connected to the second network connector LAN (it has not gateway address, it is not possible to

connect it to the Internet). The second connector WAN should be connected to the router. In this way,

the cameras are physically separated from the external network, there is no access to them from a place

other than the recorder.

It is recommended to configure the cameras before connecting to the recorder, as described in the

camera manual. The cameras should be addressed with a unique IP address within the range set in the

recorder interface.

STARTING THE DEVICE

NVR-4532-H4/F User’s manual (short) ver.1.0

11

WARNING!

Below are shown security recommendations for network architecture and configuration

of CCTV systems that are connected to the Internet to reduce the risk

of unauthorized interference with the system by a third party.

2.6. Security recommendations for network architecture and configuration

1. Absolutely change the default passwords and user names (if the device gives this possibility) of

all applied network devices (recorders, cameras, routers, network switches, etc.) to the

severely complexity password. Use lowercase and uppercase letters, numbers, and special characters

if there is such possibility.

2. Depending on the available functionality in the order to restrict access to the used network devices at

the administrator account level, it is recommended to configure the users accounts accordingly.

3. Do not use DMZ function (Demilitarized zone) in your router. Using that function you open the

access to recorder system from the Internet on all ports, which gives possibility for an unauthorized

interference with the system.

Instead of DMZ use port forwarding redirect only the ports which are necessary for the performance

of the connection (detailed information about ports of communication in different models of recorders,

cameras, etc. can be found in the operating instructions).

STARTING THE DEVICE

INTERNET PC

ROUTER

IP cameras

SWITCH

NVR-4532-H4/F User’s manual (short) ver.1.0

12

4. Use routers with firewall function and make sure it is enabled and properly configured.

5. It is recommended to change the default network communication port numbers of used devices

if there is such possibility.

6. If used network devices has a UPnP feature and it is not used, turn it off.

7. If used network devices has a P2P feature and it is not used, turn it off.

8. If used network devices support HTTPS protocol for connection, it is recommended to use it.

9. If used network devices support IP filtering for authorized connections function, it is recommended

to use it.

10. If used recorder has two network interfaces it is recommended to use both of them to physically

separate network for cameras and network for Internet connection. The only device in the system,

accessible from Internet is recorder - there is no physically access directly to any camera.

2.8. Front panel elements

1. IR receiver.

2. Power LED (green). When the LED is light on, it means NVR is working.

3. HDD LED (red). Flickering indicates the recording or playback is in progress.

4. USB port for external HDDs, Flash memory or USB mouse connection.

STARTING THE DEVICE

3

4

2

1

NVR-4532-H4/F User’s manual (short) ver.1.0

13

3. NVR OPERATING

3.1. Control

NVR-4532-H4/F recorder can be controlled using IR remote controller or USB mouse.

3.1.1. Controlling via IR remote controller

IR remote controller is included with NVR. IR range depends on battery status and may vary between a

few and several meters.

Controller is supplied with two AAA batteries. Buttons functions are listed below.

3.1.2. Controlling via USB mouse

It is possible to control all NVR functions using mouse with a USB interface. Double clicking on any

camera in split mode (e.g. 2x2, 3x3) switches it to full screen mode. Another double click returns to the

previous display mode.

A single click on a camera shows the channel menu. Moving the cursor down the screen displays the

menu bar. During configuration, the left mouse button select individual items. Some indicated

parameters can be changed by the mouse wheel. The right button allows to leave the menu.

NVR OPERATING

0 - 9

Numeric buttons for channel selection. Channel 10 and another

can be selected using buttons combination. i.e. to open channel

15 press „1” and then „5”.

ALL

Toggles between different display formats: 1, 4, 9, etc.

MENU

Enters to main menu. Pressing this button cancel the selection

and leaving the menu also.

SUBMENU

In live mode open the Popup menu.

Navigation control „left”, „right”. In live mode open the Popup

menu.

Navigation control „up” , „down”.

SEL

The button is used to confirm the selection and start to editing

fields. In live mode open the Popup menu.

Switch on playback mode. Open Record Search menu. In live

mode open the Popup menu.

Slow down playback speed.

Fast up playback speed.

Turn on manual record.

Playback pause, press again to play frame by frame.

Stop the playback. In live mode stop the manual recording.

NVR-4532-H4/F User’s manual (short) ver.1.0

14

3.2. First Launch Wizard

To start the unit connect the power cable to DC adapter, turn on the power switch on back panel and

wait for initialization. It lasts for approximately 120 seconds. During this time executing any device

functions and pressing any buttons is prohibited. After first launch NVR displays window as below. It

allows to change the language. Select the desired one from the Language list.

Default language is English. If you change the language, all the descriptions will be translated

automatically.

Click on the field to expand list or display virtual keyboard.

New Admin Name - name of administrator account (default: admin).

Password Strenght - the scale showing how strong is the written password. It is updated on the fly

while typing the password in the next fiels. Password strenght can be Low, Medium or High and

marked with Red, Yellow or Green color.

New Admin Password - it is required to create access password. It must contain 5-15 characters.

Confirm password - enter the access password again to confirm.

Show Password - shows password instead of masking marks.

Unlock Pattern Enable - enables an alternative authentication method for the password using the

pattern. It allows to enter administrative settings and make changes. Some settings, such as disk

formatting, import/export settings still require password authentication.

Draw - the function shows when Unlock Pattern function is enabled. It allows to create an unlock

pattern. There is 3x3 board to create a pattern by dragging the mouse cursor. The pattern has to be

confirmed by dragging the mouse cursor again.

Apply - saves settings.

NVR OPERATING

NVR-4532-H4/F User’s manual (short) ver.1.0

15

The next step is to log in using the created user data.

The Password button switch to login window using defined password.

The Pattern window switch back to previous window.

After authentication the First Launch Wizard opens.

NVR OPERATING

NVR-4532-H4/F User’s manual (short) ver.1.0

16

NVR OPERATING

3.3. Frist Launch Wizard

The first launch wizard provides a quick way to configure basic NVR settings.

After pressing the Start Wizard button, following sections of the wizard appear.

The Next and Previous buttons allow to toggle between consecutive sections. The Cancel button exits

the wizard without saving any changes.

3.3.1. Network Settings

NVR-4532-H4/F User’s manual (short) ver.1.0

17

NVR OPERATING

This section contains basic network settings of the WAN interface. The settings of the second

interface can be done later in the recorder menu:

DHCP - enable network settings retrieval from a DHCP server.

IP Address - network address of the recorder in the local network.

Subnet Mask - number dividing in IP address the network part.

Gateway - IP address of the router for Internet connection.

DNS1 - domain server address.

DNS2 - alternative domain server address.

Web Port- the port used to connect with the NVR network plugin by Internet Explorer browser.

Client Port - the port used to connect with the NVR by NHDR-5000Viewer, NMS, RxCamView.

RTSP Port - the port used for RTSP streaming from NVR..

HTTPS - the port used while the connection with HTTPS protocol.

UPNP - enable the UPnP discovery feature. The UPnP function must be supported by the router.

UPNP Status - informs if the UPnP function is active for the port (Active or Inactive).

3.3.2. Time and date settings

This section contains all the date and time options in the recorder.

Date - select day from calandar.

Time - current NVR time. It can be written manually.

Date Format - dispaly format of the date (MM/DD/YY, YY-MM-DD, DD/MM/YY).

Time Format - display format of time (12 Hour or 24 Hour).

Time Zone - display a time zone depending on the region.

NVR-4532-H4/F User’s manual (short) ver.1.0

18

NVR OPERATING

The recorder allows to synchronize time with the NTP server. The NTP server can be selected from

drop-down list. The User-Deifined option allows to enter any IP address of the time server.

The correct network settings and connection are required to allow communication with the NTP server.

The recorder allows to set daylight saving time.

Time Offset - defines time advancing (1Hour, 2Hour).

DST Mode - defines method of switching by specified Week, or by specified Day.

Start Time - defines first day of DST.

End Time - defines last day of DST.

3.3.3. Adding IP cameras

The next section allows to add IP channels to the recorder. The Search button starts searching IP

cameras, NHDR-4000 and NVR-4000 series Novus recorders in Local Area Network.

There is a list of found devices on the left side, list of connected devices on the right side.

NVR-4532-H4/F User’s manual (short) ver.1.0

19

NVR OPERATING

The recorders IP addresses are with sign, which allows to add separated channels from recorders. If

any channel from the recorder has already been added, its IP address is indicated by a red color.

There is an arrow in the center of the window which allow to add marked channels.

If there are selected multiple channels, the following dialog box appears to add a group with the same

data.

NVR-4532-H4/F User’s manual (short) ver.1.0

20

NVR OPERATING

Port - port number to connect devices. It is automatically recognized by default.

Protocol - protocol to connect devices. The NOVUS 4000 series IP cameras, NHDR-4000 and

NVR-4000 series are using Private protocol. Another devices are using ONVIF protocol. The

protocol is automatically recognized by default.

User Name - name of the user which is used to log in to the device. The default user name is root.

Password - user password which is used to log in to the device. The default password is pass.

Camera Mode - the mode for cameras. The Fisheye mode allows to use dewarping function,

Normal mode switch tem off. The Auto mode recognize the mode of cameras.

The Add button confirms the entered data.

Adding a single channel there shows the following window, where can be defined the above

parameters, the IP address (or domain), channel name (Alias) and channel number to assign a

specific camera.

Strona się ładuje...

AAT NVR-4532-H4/F Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

AAT NVR-4532-H4/F Instrukcja obsługi

w innych językach

Powiązane artykuły

Inne dokumenty