SUPAIR RADICAL 3 Instrukcja obsługi

User’s manual

Harness

SUP’AIR - VLD

34 rue Adrastée

Parc Altaïs

74650 Annecy - Chavanod

FRANCE

45°54.024’N / 06°04.725’E

English

Revision index : 05/12/2017

Harness User’s manual

SUP’AIR _RADICAL3 Page 2

Thank you for choosing the RADICAL3. We

are glad to be able to share our common

paragliding passion with you.

SUP’AIR has been designing, producing

and selling free ﬂying equipment since

1984. By choosing a SUP’AIR product you

beneﬁt from almost thirty years of expertise,

innovation and listening. Our mission state-

ment: research and develop to constantly

enhance our product line.

We hope you will ﬁnd this user’s manual

comprehensive, explicit and hopefully en-

joyable as well. We advise you to read it

carefully.

You will ﬁnd the lastest udated information

about this product on our website www.su-

pair.com. If you have further inquiries, feel

free to ask one of our retailers for answers.

And naturally, the entire SUP’AIR team is at

your disposal at info@supair.com

We wish you many safe enjoyable ﬂying

hours and happy landings.

Team SUP’AIR

Harness User’s manual

SUP’AIR _RADICAL3 Page 3

List of contents

Introduction 4

Technical speciﬁcations. 5

Size choice 6

Components list 7

Equipment overview 8

Accessories assembly. 9

Carabiners 9

Speed-bar system 10

AirBag/Backpack 11

Safe-T kit 13

Installing the reserve parachute. 14

Necessary gear 14

Connection Harness-risers 15

Reserve parachute-harness connection 16

Installing the front reserve parachute 17

Adjustments 18

The various adjustments 18

Adjusting the harness 19

Wing/harness connection 20

Gear packing and tips 21

Inﬂight behavior 22

Flight phases 23

Pre-Flight check 23

Takeoff 23

In ﬂight 24

Speed-bar use 24

Landing 24

Using the reserve parachute 25

Towing 25

Mandatory thorough checkup 25

Maintenance 26

Harness cleaning and maintenance 26

Storage and transport 26

Product lifespan 26

Repairs 27

Spare parts. 27

Materials 27

Recycling 27

Warranty 28

Disclaimer 28

Pilot’s gear 28

Service Book 29

Harness User’s manual

SUP’AIR _RADICAL3 Page 4

Welcome to the paragliding world according to SUPAIR; a world of shared passion.

The RADICAL3 was designed for pilots coming out of school or in progression. It brings comfort and peace of mind to pilots experienc-

ing their ﬁrst XC ( Cross-Country ) ﬂights to discover new horizons !

The well though out design and choice of materials were guided by the same quality and longevity objectives.

The harness RADICAL3 harness was certiﬁed EN 1651 : 1999

The harness RADICAL3 + RADICAL3 Reversible backpack airbag was certiﬁed EN 1651 : 1999 and LTF* 91/09

* The RADICAL-3 LTF certiﬁcation is valid only if the AirBag and the Safe-T kit are installed.

Indicating that it meets European and German safety requirements.

After reading this manual we suggest you to check your harness during a hang-test to adjust it before your ﬁrst ﬂight.

Introduction

N.B : Three important icons will help you when reading this manual

Advice Caution ! Danger !!

Harness User’s manual

SUP’AIR _RADICAL3 Page 5

A

B

C

D

E

F

S/M L

Pilot size (cm) 160 / 180 180 / 200

Pilot weight (mini - maxi) 50 - 80 70 - 110

Harness weight (+carabiners+speedbar) (g) 830 870

Designed for paragliding only

Backrest height (cm) A65 72

Backrest tilt adjustments (cm) B33 36

Seat depth (cm) C37 42

Hooking point height. (cm) E45 45

Length between the hooking points. (cm) F35 - 43 35 - 43

Impact damping system: Airbag Options

Impact damping system: Bumpair No

RADICAL3 harness certiﬁcation Yes : EN 1651 : 1999

RADICAL3 harness certiﬁcation + AirBag/Backpack Yes : EN 1651 : 1999 and LTF 91/09

Tandem (Pilot or Passenger) Yes

Acrobatic ﬂying No

Towing Yes

Technical speciﬁcations

ABackrest height.

BBackrest tilt adjustments.

CSeat depth.

DSeat width

EHooking point height.

FLength between the hooking points.

Characteristics Harness size

Harness User’s manual

SUP’AIR _RADICAL3 Page 6

Choosing the right harness size is important. You will ﬁnd below a height/weight chart to help you with your size choice. With its ham-

mock architecture and reclined ﬂying posture, we advise you to try out the harness during a hang-test ﬁrst at one of our retailers loca-

tion to choose the correct size.

For a complete list of our retailers list click here : www.supair.com

Size choice

Preliminary hang-test.

Size

Weight 1m60 1m65 1m70 1m75 1m80 1m85 1m90 1m95 2m

50 S/M S/M S/M S/M

55 S/M S/M S/M S/M S/M

60 S/M S/M S/M S/M S/M

65 S/M S/M S/M S/M S/M

70 S/M S/M S/M S/M L L L L

75 S/M S/M S/M S/M L L L L

80 S/M S/M S/M S/M L L L L

85 L L L L L

90 L L L L L

95 L L L L L

100 L L L L

S/M

L

Harness User’s manual

SUP’AIR _RADICAL3 Page 7

4

2Zicral 30 mm carabiners.

Nomenclature

Harness

1

3

2

Options

Reversible AirBag/Backpack

Light double stage accelerator/speed-bar (réf. ACCELSOUPLELIGHT)

4

5

1

Removable storage pocket

3

Optional Safe-T kit

4

Harness User’s manual

SUP’AIR _RADICAL3 Page 8

Harness overview

Chest strap with buckles.

Leg strap buckles.

Chest strap adjustment.

Backrest tilt adjustment.

Paragliding main hooking points.

Reserve parachute hooking points.

2

1

3

4

5

7

8

9Back storage pocket.

Shoulder straps adjustments.

6

Speed-bar grommets.

2

13

4

5

7

8

9

6

7

2

44

55

66

8

88

Harness User’s manual

SUP’AIR _RADICAL3 Page 9

Accessories assembly

1. Carabiners.

Harness User’s manual

SUP’AIR _RADICAL3 Page 10

1

2

LIGHT double stage speed-bar/accelerator.

Accessories assembly

2. Speed-bar system.

>> Compatible accelerator/speed-bar

Ref. : ACCELSOUPLELIGHT

>> Speed-bar assembly

Regarding either side of the harness:

1. Push the speed-bar line through the grommet loca-

ted at the front of the seat.

2. Push the speed-bar line through the grommet located

on the lateral skirt of the harness.

5. Finally, attach a cimped hook to the cord before connec-

ting it to the glider’s speed-bar/accelerator.

6. Simulate the speed-bar/accelerator’s functionality by sli-

ding the cord back and forth.

1

2

Caution !

If you have a front mounted

reserve parachute setup, be

sure to guide the speed-bar

line between the risers and the

harness, not to hinder the rescue

parachute’s extraction/deploy-

ment sequence.

Harness User’s manual

SUP’AIR _RADICAL3 Page 11

Accessories assembly

3. Optional AirBag/Backpack

>> Removing the dorsal pocket

2 Unfasten the Velcro located at the back of the harness

3 Unfasten the Velcro located under the seat

1 Unfasten the lateral Zippers located on each side of the pocket

>> Layout the harness ﬂat, with the seating and torso area

facing the ground

A

C

B

A

B

C

A

C

B

A

Harness User’s manual

SUP’AIR _RADICAL3 Page 12

>> Connect the AirBag/Backpack, AirBag side to the harness

3. AirBag/Backpack ( Option ) continued

Accessories assembly

A

C

B

D

A

B

A

C

D

1 Fasten the Zippers on each side A

3 Fasten the lower Velcro C

2 Fasten the upper Velcro B

4 Fasten the front of the AirBag using

the connection straps by pushing the

rectangular buckles through the metal

rings D

2

1

3

4

Harness User’s manual

SUP’AIR _RADICAL3 Page 13

4. SAFE-T KIT

Mise en place des accessoires

For practical reasons, the RADICAL-3 was designed without a Safety-T strap. If you wish to have one, or have a harness meeting the LTF certiﬁcation

standard requirements, you must install this kit. It enables one of the leg straps to be permanently closed, hence preventing the risk of taking off in a

unfastened harness.

This kit includes :

- A neoprene sleeve.

- A small strap.

1. Open the chosen leg strap, and slide

the neoprene sleeve.

2. Close the leg strap.

3. Use the strap to lock the buckle :

Insert the strap through the buckle and the guide, then loop it back in, as indicated on the images below.

4. Slide the neoprene sleeve over the straps and buckle, to secure and protect the assembly.

To strap your harness on, start by entering one leg through the closed leg strap.

Reverse the entire procedure to remove the Safe-T strap.

Harness User’s manual

SUP’AIR _RADICAL3 Page 14

Thank you for reading the following carefully ! We recommend for the initial rescue parachute assembly and installation to be made

by a qualiﬁed professional.

Reserve parachute folding and installation inside the harness must conform to the speciﬁc guidelines found in this manual.

Installing the reserve parachute

DSingle reserve parachute handle

Reserve parachute packed in its POD ( according to the manufacturer’s recommendations )

B

C

A

Independent Dyneema® risers

Front reserve parachute container with handle

ESquare 7mm Maillon Rapide®

>> Needed gear to install the reserve parachute

FToric elastic rings

D

B

C

A

F

E

Harness User’s manual

SUP’AIR _RADICAL3 Page 15

Installing the reserve parachute

>> Connection risers/harness

2. Attach each riser to the shoulder

attachment points by making a

Lark’s knot ( loop to loop connec-

tion ). Use the largest bridle loop

ends.

3. - Assemble everything correctly.

- Make sure for the risers not to be longer

than one another.

- Tighten each connection securely.

WARNING !

The reserve parachute connection points are colored black and located

above the shoulders.

1. Notice the reserve parachute’s attachment point on the harness – reinforced black

webbing loops located on the upper section of the shoulder straps.

Shoulder straps

adjustments

Reserve parachute

connection points

Harness User’s manual

SUP’AIR _RADICAL3 Page 16

Installing the reserve parachute

>> Riser reserve parachute connection

1. - Push the left riser from the right side of the harness over the shoul-

ders, and keep it in place using the fastening loop.

2. - Keep the risers in place in the sleeve located on the harness’s right side.

Harness User’s manual

SUP’AIR _RADICAL3 Page 17

Installing the reserve parachute

1. - Open the 7mm square

Maillon Rapide®

- Connect the reserve para-

chute single riser loop

- Push the maillon through

the plastic ring

- Twist

3. - Give a second twist to

the plastic ring

- Push the buckle through

the maillon

2. - Push the end riser

through the toric ring

- Push the maillon through

the risers buckles

4. - If you use separate/in-

dependente risers Repeat

steps 1 through 3 with the

second riser

- If you use separate risers

5. - Tidy up the assembly

- Be certain for the risers end

loops to be securely fas-

tened

- Close the Maillon Rapide®

tightly by hand

- Tighten using pliers and

making a ¼ turn

One (1) square 7mm Maillon Rapide® will be needed + two (2) ﬂexible toric rings.

>> Installing the front mounted reserve parachute

For the following procedure :

- Connect the reserve parachute handle to the POD.

- Pack your reserve parachute inside your reserve parachute container.

- Connect the reserve container to the harness.

Carefully and exactly follow the installation procedure provided and recommended by the front mounted reserve parachute container manufacturer.

WARNING !

If you have a front mounted

reserve parachute setup, be

sure to guide the speed-bar

line between the risers and

the harness, not to hinder

the rescue parachute’s

extraction/deployment

sequence.

Check the completed installation during

a hang-test.

Have the installation checked by a professional outﬁt.

Conduct an extraction test every six ( 6 ) months to assure proper system functionality.

Note : conducting and extraction test does not imply deploying the reserve para-

chute which will stay inside its POD.

>> Riser reserve parachute connection

Harness User’s manual

SUP’AIR _RADICAL3 Page 18

1

3

4

2

3

Adjusting the harness prior each takeoff is vital.

Adjusting the harness

Adjusting the chest strap

Adjusting the backrest

Adjusting the shoulder straps

>> The various adjustments

2

1

3

4Leg straps width adjustment

2

3

Harness User’s manual

SUP’AIR _RADICAL3 Page 19

3. Adjust the shoulder straps length using the trimmers.

The pressure on the shoulder straps contributes to general comfort in ﬂight. It must be precise: not too tight nor too loose. The upper

area of the straps must offer enough support to maintain your torso in a comfortable position.

Harness adjustments

>> Adjusting the harness.

2. Adjusting the chest strap.

The distance to consider corresponds to the length between the middle points at the bottom of each carabiner.

The ideal distance varies between paragliding wing models.

Adjust your harness’s chest strap according to the wing manufacturer’s recommendations.

Tightening the chest-strap provides more stability but less piloting efﬁciency while increasing the risk of riser twisting.

On the contrary loosening the strap provides more efﬁciency but can be dangerous in turbulent aerology (increased risk of falling

towards the collapsed side of your glider).

1. Without strap tension, ﬁrst adjust the backrest incline at the desired angle.

>> Tightening will bring the backrest at a more vertical angle ( recommended posture for beginners ).

>> Loosening the backrest will tilt the back support rearward. tighten (strap)

loosen (strap)

tighten (strap)

loosen (strap)

tighten (strap)

loosen (strap)

Harness User’s manual

SUP’AIR _RADICAL3 Page 20

Without twisting the risers, connect them to the harness attachment loops using the self-locking carabi-

ners.

Check for the risers to be properly positioned and untwisted. The «A» risers must be located at the front

and facing the ﬂight direction (see diagram).

Lastly, check for the main self-locking carabiners to be fully closed and locked in place.

>> Connecting the wing to the harness.

Connecting the wing to the harness

Install the accelerator by following the previous instruc-

tions.

Connect it to the wing using the split hooks.

Once the accelerator/speedbar is connected adjust its

length according to the wing recommended measure-

ments.

For correct use, there must not be any line tension at the

split hook level when the accelerator/speedbar line is fully

relaxed.

>> Installing the accelerator. Self-locking

carabiners.

Harness Flight direction.

« A » risers

left side.

Strona się ładuje...

SUPAIR RADICAL 3 Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

SUPAIR RADICAL 3 Instrukcja obsługi

w innych językach

Powiązane artykuły

Inne dokumenty