AAT NVIP-3SD-8200/30 Instrukcja obsługi

Quick start guide

NVIP-3SD-8200/30

NVIP-3SD-8200/30 Quick start guide ver.1.1

2

IMPORTANT SAFEGUARDS AND WARNINGS

THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING DIRECTIVES:

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed

for self installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other

devices during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN

PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE

PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE

PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF EXCLUDING

THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.

DIRECTIVE 2014/35/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 26 February 2014 on the harmonisation

of the laws of the Member States relating to the making available on the

market of electrical equipment designed for use within certain voltage limits.

DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIMENT

AND OF THE COUNCIL of 26 February 2014 on the harmonisation

of the laws of the Member States relating to electromagnetic compatibility

(OJ L 96, 29.3.2014, p. 79–106, with changes)

DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 4 July 2012 on waste electrical and electronic

equipment (WEEE) (OJ L 197, 24.7.2012, p. 38–71,with changes)

DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 8 June 2011 on the restriction of the use

of certain hazardous substances in electrical and electronic equipment

(OJ L 174, 1.7.2011, p. 88–110, with changes)

NVIP-3SD-8200/30 Quick start guide ver.1.1

3

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH THE

MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER-

SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL MAY

OPEN THE DEVICE.

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS.

IMPORTANT SAFEGUARDS AND WARNINGS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct influence

on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is forbidden;

7. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

8. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly mounted

camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted by qualified

personnel with proper authorization, in accordance with this user’s manual.

9. Device should be supplied only from a power sources whose parameters are in accordance with those specified

by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera from a power

sources with unknown parameters, unstable or not meeting producer’s requirements;

10. Signal cables (conducting TV or / and telemetric signal) should be placed in a way excluding the possibility

of damaging them by accident. Special attention must be paid to cables getting from the camera and connecting

the power supply;

11. To avoid equipment damage, whole TV circuit should be equipped with properly made discharge, overload

and lightning protection devices. Usage of separating transformers is advised;

12. Electric installation supplying the device should be designed to meet the specifications given by the producer

in such a way that overloading is impossible;

13. User cannot repair or upgrade the equipment himself. All maintenance actions and repairs should be conducted

only by qualified service personnel;

14. Unplug the camera from the power source immediately and contact the proper maintenance department

when the following occurs:

• Damages to the power cord or to the plug itself;

• Liquids getting inside the device or exposure to strong mechanical shock;

• Device behaves in a way not described in the manual and all adjustments approved by the manufacturer

and possible to apply by user himself, seem not to have any effect;

• Camera or its casing is damaged;

• Atypical behaviour of the camera components can be seen (heard).

15. In necessity of repairs attention to using only original replacement parts (with their parameters in accordance

with those specified by the producer) should be paid. Non-licensed service and non-genuine replacement parts

may cause fire or electric shock.

NVIP-3SD-8200/30 Quick start guide ver.1.1

4

FOREWORD INFORMATION

1. FOREWORD INFORMATION

1.1. General characteristic

• Mechanical IR cut filter

• IR operation capability - built-in IR LED illuminator

• Imager resolution: 3 megapixels

• Min. Illumination: from 0.007 lx/F1.6 - B/W mode, 0.07 lx/F=1.6 color mode

• Motor-zoom lens, AI and AF function

• Wide Dynamic Range (WDR 120dB) for enhanced image quality in diverse light conditions

• Automatic DSS function

• Object tracking (Auto Tracking)

• 12 tours (max. 32 presets each)

• 12 auto-scan functions

• 6 patterns

• 393 preset commands

• Privacy zones: 4, type color

• Optical zoom: up to 30x

• 7 alarm inputs & 2 alarm relay outputs (NO/NC)

• “Auto-Flip” function allows the tilt to rotate 180° and reposition itself for continuous viewing of a

moving object directly beneath the dome

• Compression: H.264, H264+, H.265, H265+, M-JPEG

• Bidirectional audio transmission

• Video processing resolution: up to 2048 x 1536

• RTP/RTSP protocol support for video & audio transmission

• Triple stream mode: compression, resolution, speed and quality defined individually for each video

stream

• Built-in web server: camera configuration through the website

• Diverse definition of system reactions to alarm events: e-mail with attachment, alarm output

trigger, PTZ function activation, save on FTP

• PTZ control directly from the website and NMS (NOVUS MANAGEMENT SYSTEM)

• Network protocols support: ONVIF Profile S/Q, HTTP, TCP/IP, IPv4, IPv4/v6, UDP, HTTPS,

FTP, DHCP, DNS, DDNS, NTP, RTSP, RTP, UPnP, SNMP, PPPoE, RTCP

• Software: NMS for video recording, live monitoring, playback and remote IP devices

administration

• IP 66

• Housing and wall mount bracket in-set included

• Power supply: 24 VAC, High PoE (60W) - compatible with NV-8000PS/HP High PoE Injector

Information:

Depending on the type of recorder/registration system, the range of features and options may vary. Full

list of camera functionality available from a given type of recorder is included in the Compatibility

Table available on www.novuscctv.com/en

NVIP-3SD-8200/30 Quick start guide ver.1.1

5

FOREWORD INFORMATION

1.3 Technical Specification

Image

Image Sensor 3 MPX CMOS sensor 1/2.8” SONY Exmor R STARVIS

Number of Eecve Pixels 2065 (H) x 1553 (V)

Min. Illuminaon

0.07 lx/F1.6 - color mode,

0.007 lx/F1.6 - B/W mode,

0 lx (IR on) - B/W mode

S/N Rao > 55 dB (AGC o)

Electronic Shuer auto/manual: 1/5 s ~ 1/20000 s

Digital Slow Shuer (DSS) up to 1/5 s

Wide Dynamic Range (WDR) yes (double scan sensor), 120dB

Digital Image Stabilizaon (DIS) yes

Digital Noise Reducon (DNR) 2D, 3D

Defog Funcon (F-DNR) yes

Highlight Compensaon (HLC) yes

Back Light Compensaon (BLC) yes

Lens

Opcal Zoom 30x

Lens Type motor-zoom, auto-iris funcon, f=4.5 ~ 135 mm/F1.6 ~ F4.4

Auto-focus connuous, zoom trigger, manual trigger

Day/Night

Switching Type mechanical IR cut lter

Switching Mode auto, manual, me

Switching Level Adjustment yes

Switching Delay 0 ~ 180 s

Switching Schedule yes

Visible Light Sensor yes

Network

Stream Resoluon

2048 x 1536 (QXGA), 1920 x 1080 (Full HD), 1280 x 720 (HD), 704 x 576,

704 x 480, 640 x 480 (VGA), 640 x 360, 352 x 288 (CIF), 352 x 240,

320 x 240 (QVGA)

Frame Rate 30 fps for 2048 x 1536 (QXGA) and lower resoluons

Mulstreaming Mode 3 streams

Video/Audio Compression H.264, H.264+, H.265, H.265+, MJPEG/G.711, RAW_PCM

Number of Simultaneous Connecons max. 8

Bandwidth 30 Mb/s in total

Network Protocols Support

HTTP, TCP/IP, IPv4, IPv4/v6, UDP, HTTPS, FTP, DHCP, DNS, DDNS, NTP, RTSP,

RTP, UPnP, SNMP, PPPoE, RTCP

ONVIF Protocol Support Prole S/Q

Camera Conguraon

from Internet Explorer browser

languages: Polish, English, Russian, and others

Compable Soware NMS

NVIP-3SD-8200/30 Quick start guide ver.1.1

6

FOREWORD INFORMATION

*Inactive when Auto Tracking enabled

PTZ

Preset Commands 393

Tours 12 (up to 32 presets per tour)

Auto-Scans 12

Paerns 6

Tilt/Pan Range 0° ~ 98°/360° (connuous)

Pan/Tilt Speed up to 180°/s (proporonal to zoom)

Preset Speed up to 180°/s

Protocols Pelco-D

Other funcons

Privacy Zones 4 video mask type: single color*

Moon Detecon yes

Region of interest (ROI) 8

Video Content Analysis (VCA) Auto Tracking, zone entrance detecon and object tracking

Image Processing 180˚ image rotaon, sharpening, mirror eect

System Reacon to Alarm Events e-mail with aachment, saving le on FTP server, alarm output acvaon, PTZ

IR LED

LED Number 10

Range up to 200 m (depends on current opcal zoom value)

Angle up to 45° (depends on current opcal zoom value)

Interfaces

Video Output BNC, 1.0 Vp-p, 75 Ohm - maintenance only

Audio Input/Output 1 x RCA/1 x RCA

Alarm Input/Output 7 (NO/NC)/2 relay type

RS-485 yes

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Installaon parameters

Dimensions (mm) 226 (Ф) x 363 (H) with bracket: 226 (W) x 425 (H) x 345 (L)

Weight 5.1 kg with bracket: 6.1 kg

Degree of Protecon IP 66 (details in the user’s manual)

Enclosure

aluminium, white, in set: outdoor housing (integrated with the camera),

wall mount bracket

Power Supply 24 VAC, High PoE (60W) - compable with NV-8000PS/HP High PoE Injector

Surge protecon TVS 6000 V

Power Consumpon 18 W, 46 W (IR and heater on)

Operang Temperature -30°C ~ 60°C

Built-in Heater/Fan yes/yes

NVIP-3SD-8200/30 Quick start guide ver.1.1

7

FOREWORD INFORMATION

1.3. Camera dimensions (in millimeters)

345

207

363

425

Ф226

NVIP-3SD-8200/30 Quick start guide ver.1.1

8

1.4. Package contents

After you open the package make sure that the following elements are inside:

If any of this elements has been damaged or missing during transport, pack all the elements back into

the original box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches

the temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

FOREWORD INFORMATION

Novus IP PTZ camera 1 pcs

Wall bracket 1 pcs

Power adapter AC230V/AC24V 1 pcs

Slotted screwdriver Φ2.5 mm 1 pcs

White glove 1 pcs

Connection terminal 2Pin 2 pcs

Bolts: PM 3X 12mm 3 pcs

User’s manual (short form) 1 pcs

NVIP-3SD-8200/30 Quick start guide ver.1.1

9

2. START-UP AND INITIAL IP CAMERA CONFIGURATION

2.1. Description of connectors

1. Alarm Connectors 5. Power Connector (24VAC)

2. Audio output 6. Ground

3. Audio input 7. RJ-45 Connector

4. BNC—analog output 8. RS-485 Connectors

START-UP AND INITIAL CAMERA CONFIGURATION

1

2

3

5

7

4

8

6

NVIP-3SD-8200/30 Quick start guide ver.1.1

10

2.2. Connecting power supply to the camera.

Camera can be supplied using external power supply unit corresponding with the camera parameters.

When selecting the power supply, also take into account the power consumption of the heater.

CAUTION!

In order to provide protection against voltage surges/lightning strikes, usage of appropriate

surge protectors is advised. Any damages resulting from surges are not eligible for service

repairs.

CAUTION!

It is forbidden to use – as the camera power source – PoE equipment (adapters, etc.)

not compatible with IEEE 802.3af standard (items called “passive PoE power supply”). If use a

PoE technology to power the camera, use a High PoE NV-8000PS / HP power injector.

d

Damages that results from the usage of improper power supply source are not covered

by the warranty.

START-UP AND INITIAL CAMERA CONFIGURATION

No Color Funkction Describe

1

brown Alarm output 1

Two alarm outputs, configurable: NC, NO or pulse

(relay, 12VDC, 2.5A max.)

brown-black Alarm output 1 (COM)

red Alarm output 2

red-black Alarm output 2 (COM)

orange Alarm input 1

Seven alarm inputs, configurable: NC or NO

orange-black Alarm input 2

yellow Alarm input 3

yellow-black Alarm input 4

green Alarm input 5

green-black Alarm input 6

blue Alarm input 7

blue-black Alarm input COM

2 red Audio Output (RCA)

AUDIO OUTPUT:

For connecting external audio devices such as

speakers with an amplifier

3 white Audio Input (RCA)

AUDIO INPUT:

For connecting external audio devices such as

a microphone with an amplifier

4 - BNC connector Analog maintance signal

5

red

Power Supply 24VAC

AC24-IN-POWER:

Power supply cord AC 24V

black

6 yellow uziemienie

GNDEARTH:

Ground wire

7 - Ethernet (RJ-45)

Ethernet connector

8

green RS-485 + connector

External keyboard connectors

yellow RS-485 - connector

NVIP-3SD-8200/30 Quick start guide ver.1.1

11

2.3. Mounting the camera

In order to obtain declared degree of protection please seal the mounting place additionally with

appropriate sealing mass, paying special attention to mounting holes.

CAUTION!

Declared degree of protection of the camera concerns to it case and does not include the

possibility penetration of moisture through connecting cables. Securing cables is a responsibility

of person who install the camera. The manufacturer is not responsible for any injury, damage of

the camera caused by any failure above-mentioned duty, what also means they are not subject to

warranty repairs.

CAUTION!

Due to safety reasons, maximum load capacity of surface shouldn’t be less than 25kg.

In order to successfully mount a camera, please follow the procedure below:

• Put the bracket to the wall in a desired mounting place (with cable hole). Taking the bracket’s

base screw holes as a pattern, mark future drilling holes for screws using a punch.

• Drill 4 holes in accordance with previously done markings, insert the expansion plugs into the

holes.

• Screw the muff into the bracket and lock the muff with the locking screw.

• Thread the wires through the hole in the muff of bracket.

• Attach the camera to the muff in bracket, tighten the three bolts to fix the bracket and camera

and then hook the safety cord in the bracket

• By using the description of the terminals from the previous chapter and the appropriate

accessories, connect required signal and power supply cables.

WARNING!

Connection the power cable to the camera must be performed after disconnecting the power

source. Power can be on only after the camera is fully mounted.

• Put the excess cable back into the bracket.

• Screw on the camera with the bracket to the wall.

After the above steps the camera is ready to work

START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-3SD-8200/30 Quick start guide ver.1.1

12

2.4. Starting the IP camera

To run NOVUS IP camera connect 24 VAC power supply or NV-8000PS/HP High PoE Injector.

Initialization process takes about 1 minute. Then you can proceed to connect to the camera via web

browser.

The recommended way to start an IP camera and perform its configuration is a connection to the PC

via the network switch which is not connected to other devices.

To obtain further information about network configuration parameters (IP address, gateway, network

mask, etc.) please contact your network administrator.

• Connection using external power supply and network switch

• Connection using the network switch and power supply of the camera via the

High PoE NV-8000PS / HP power supply

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission

Network

transmission

Network Switch

Computer

Power supply

Network

transmission

Network

transmission

Power

and Network

Network

switch

Computer

IP Camera

NV-8000PS/HP

NVIP-3SD-8200/30 Quick start guide ver.1.1

13

• Connection using external power supply, directly to the computer.

2.5. Initial configuration via the web browser

The default network settings for Novus cameras are :

1. IP address- 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address set PC IP address appropriately, so the two devices can operate in

one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera is from range

192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses

for camera and PC computer

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission - cross over cable

Computer

Power supply

NVIP-3SD-8200/30 Quick start guide ver.1.1

14

2.6. Security recommendations for network architecture and configuration

WARNING!

Below are shown security recommendations for network architecture and configuration

of CCTV systems that are connected to the Internet to reduce the risk

of unauthorized interference with the system by a third party.

1. Absolutely change the default passwords and user names (if the device gives this possibility) of

all applied network devices (recorders, cameras, routers, network switches, etc.) to the

severely complexity password. Use lowercase and uppercase letters, numbers, and special characters

if there is such possibility.

2. Depending on the available functionality in the order to restrict access to the used network devices

at the administrator account level, it is recommended to configure the users accounts accordingly.

3. Do not use DMZ function (Demilitarized zone) in your router. Using that function you open the

access to recorder system from the Internet on all ports, which gives possibility for an unauthorized

interference with the system.

Instead of DMZ use port forwarding redirect only the ports which are necessary for the performance

of the connection (detailed information about ports of communication in different models

of recorders, cameras, etc. can be found in the operating instructions).

4. Use routers with firewall function and make sure it is enabled and properly configured.

5. It is recommended to change the default network communication port numbers of used devices

if there is such possibility.

6. If used network devices has a UPnP feature and it is not used, turn it off.

7. If used network devices has a P2P feature and it is not used, turn it off.

8. If used network devices support HTTPS protocol for connection, it is recommended to use it.

9. If used network devices support IP filtering for authorized connections function, it is recommended

to use it.

10. If used recorder has two network interfaces it is recommended to use both of them to physically

separate network for cameras and network for Internet connection. The only device in the system,

accessible from Internet will be recorder - there will be no physically access directly to any camera.

START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-3SD-8200/30 Quick start guide ver.1.1

15

NETWORK CONNECTION VIA WEB BROWSER

3. NETWORK CONNECTION VIA WEB BROSWER

3.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming image display in 2048 x 1536

resolution and 30 fps speed.

1. CPU Intel i5 3 GHz or faster

2. RAM Memory min. 4 GB

3. VGA card (any displaying Nvidia GeForce 512MB Ram memory)

4. OS Windows 7 / 8 / 10

5. Network card 100/1000 Mb/s

3.2. Connection with IP camera via web browser

CAUTION!:

To maintain correct operation as snapshot or video recording, must enable the browser as an

administrator, also to maintain correct operation as playback, must add IP camera address to

Compatibility View in browser settings.

Enter camera IP address in the web browser address bar. If IP address is correct user login window will

be displayed:

Default user is root and default password is pass.

In the Language box you can change the display language. The default language is English.

For safety reasons, it is recommended to change default user name and password.

NVIP-3SD-8200/30 Quick start guide ver.1.1

16

If first time running the camera, you will see screen as below.

To correctly camera working, you need a plugin, download and install it as below.

• Click Download and setup and follow the prompts.

NETWORK CONNECTION VIA WEB BROWSER

Download and setup

NVIP-3SD-8200/30 Quick start guide ver.1.1

17

• Click Install button

• After installation, click Finished button

CAUTION: In Windows Vista/7/8/10 the ActiveX applet may be blocked by Windows

Defender or User account control. In such case you should allow to run this applet, or simply

disable these functions.

CAUTION: If the installation fails, changing security settings for the IE browser is required.

In order to do that, please choose: Tools > Internet options > Security tab > Custom level

and enable the function Download of unsigned ActiveX controls.

NETWORK CONNECTION VIA WEB BROWSER

NVIP-3SD-8200/30 Quick start guide ver.1.1

18

WWW INTERFACE - WORKING WITH CAMERA

4. WWW INTERFACE - WORKING WITH IP CAMERA

4.1. Displaying live video

1. Camera menu:

• Live Video - opens the camera live video

• Playback - function inactive

• Configuration - opens the camera configuration menu

2. Change Password and Sign out buttons - are used to change the password and log off the

current user.

3. Live video preview

4. Stream information

5. Live video menu

• Selection of stream preview

• PTZ button - turn on PTZ window

• 3D button - turn on/off 3D control

• Video button - turn on/off camera preview output

• Live / Smooth Button- turn-on smooth preview option

• Audio button - turn on/off audio output

• Interphone button - turn on/off audio input and output

• Sensor button - turn on sensor configuration menu

• Snapshot button - make a preview snapshot

• VCA button - turn on/off VCA graphics on the screen

1.

3.

4.

5.

2.

NVIP-3SD-8200/30 Quick start guide ver.1.1

19

2. Video Parameter

Stream - Stream ID (choose one from available streams)

Bite Rate Type - Information about bit rate type

Bit Rate (kbps) - Information about bit rate

I Frame Interval - Information about I frame interval

Quality - Information about quality

USE TIME STAMP - Video buffer (increases delay when enabled, maximum delay is 5s)

NOTICE: USE TIME STAMP function will not be available when using Flash instead of ActiveX.

3. PTZ Control Panel

PTZ Configure:

Preset - Programming, deleting, and recalling presets

Track - Programming, deleting, and recalling tracks

Speed - Setting speed of movement

3D Position - Turns on/off control using the mouse

North - Setting orientation of the camera

Timer - Setting schedules

PTZ Control:

Arrow keys - Controlling the movement of the camera: up/down, right/left

„Home” key - Function unavailable

Zoom - Zoom control

Focus - Focus control

Iris - Function unavailable

Brush - Function unavailable

On/Off IR - Function unavailable

4. Menu bar

Change Password - Change users password

NOTICE: Default password "pass" can be restored only after restoring default settings of the camera)

Sign Out - Log out from camera

5. Video Control

Camera - Default number of the camera is 1.

Video - Turn on/off video

Audio - Turn on/off audio

Interphone - Turn on/off Interphone

NOTICE: Audio and Interphone functions will not be available when using Flash instead of Activex.

RESTORING DEFAULTS

4.2 Adding a site to the Compatibility View list

1. Open Internet Explorer, select the Tools button and then select Compatibility View settings (1).

2. Under Add this website, enter the URL of the site you want to add to the list (2), and then select

Add (3).

5. RESTORING FACTORY DEFAULTS

Novus IP cameras allow to restore defaults via www menu.

5.1. Software restoration of factory settings the IP camera

User can restore default settings of the IP camera included the network settings (optional). To restore to

default settings go to: Maintenance -> Device Restart tab. Process of restoring takes about two

minutes.

1.

2.

3.

2020-11-20 JZ MK MM (PF)

AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.

431 Pulawska St., 02-801 Warsaw, Poland

tel.: +4822 546 0 546, [email protected]

www.novuscctv.com

Strona jest ładowana ...

AAT NVIP-3SD-8200/30 Instrukcja obsługi

AAT NVIP-3SD-8200/30 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty