Novus NVIP-2Q-6101/PIR/W Instrukcja obsługi

Quick sta rt gu i de

NVIP-2Q-6101/PIR/W

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

2

IMPORTANT SAFEGUARDS AND WARNINGS

THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING DIRECTIVES:

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed

for self installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other

devices during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN

PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE

PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE

PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF EXCLUDING

THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.

DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 26 February 2014 on the harmonisation of the

laws of the Member States relating to electromagnetic compatibility

(OJ L 96, 29.3.2014, p. 79–106, with changes)

DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 4 July 2012 on waste electrical and electronic

equipment (WEEE) (OJ L 197, 24.7.2012, p. 38–71,with changes)

DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT

AND OF THE COUNCIL of 8 June 2011 on the restriction of the use

of certain hazardous substances in electrical and electronic equipment

(OJ L 174, 1.7.2011, p. 88–110, with changes)

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

3

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER DEVICE

OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH THE MANUAL

PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER-

SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL MAY OPEN

THE UNIT.

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE PERSONNEL

AND SHOULD CONFORM TO ALL LOCAL REGULATIONS.

IMPORTANT SAFEGUARDS AND WARNINGS

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is

necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s

manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is forbidden;

7. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself as a consequence;

8. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted

by qualified personnel with proper authorization, in accordance with this user’s manual.

9. Device should be supplied only from a power sources whose parameters are in accordance with those

specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera

from a power sources with unknown parameters, unstable or not meeting producer’s requirements;

10. Signal cables (conducting TV or / and telemetric signal) should be placed in a way excluding the possibility

of damaging them by accident. Special attention must be paid to cables getting from the camera and

connecting the power supply;

11. To avoid equipment damage, whole TV circuit should be equipped with properly made discharge-, overload-

and lightning protection devices. Usage of separating transformers is advised;

12. Electric installation supplying the device should be designed to meet the specifications given by the producer

in such a way that overloading is impossible;

13. User cannot repair or upgrade the equipment himself. All maintenance actions and repairs should be

conducted only by qualified service personnel;

14. Unplug the camera from the power source immediately and contact the proper maintenance department

when the following occurs:

• Damages to the power cord or to the plug itself;

• Liquids getting inside the device or exposure to strong mechanical shock;

• Device behaves in a way not described in the manual and all adjustments approved by the

manufacturer and possible to apply by user himself, seem not to have any effect;

• Camera or its casing is damaged;

• Atypical behaviour of the camera components can be seen (heard).

15. In necessity of repairs attention to using only original replacement parts (with their parameters in accordance

with those specified by the producer) should be paid. Non-licensed service and non-genuine replacement

parts may cause fire or electric shock.

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

4

TABLE OF CONTENTS

TABLE OF CONTENTS .................................................................................................... 4

1. FOREWORD INFORMATION ................................................................................... ..5

1.1. General characteristics......................................................................................... 5

1.2. Technical specification .................................................................................... ...6

1.3. Camera dimension ........................................................................................... ...8

1.4. Package contents .............................................................................................. ...8

2. START-UP AND INITIAL CAMERA CONFIGURATION ...................................... 9

2.1. Description of camera components and connectors ............................................ 9

2.2. Power supply connection ..................................................................................... 9

2.3. Connection of alarm input/output ...................................................................... 10

2.4. Connecting the LAN network cable .................................................................. 11

2.5. Camera mounting .............................................................................................. 11

2.6. Starting the camera ............................................................................................ 12

2.6.1. Starting with connecting the camera to a wired LAN network ................ 12

2.6.1.1. Configuring network settings using a DHCP server ..................... 13

2.6.1.2. Manual configuration of network settings ..................................... 13

2.6.2. Starting with connecting the camera to a WiFi network .......................... 13

2.7. Security recommendations for network architecture and configuration ........... 14

3. CONNECTING FROM A PC WITH A WEB BROWSER ....................................... 15

3.1. First connection to the camera ........................................................................... 15

3.2. Login screen ....................................................................................................... 16

3.3. Remote view window ......................................................................................... 17

4. CONNECTION FROM A DEVICE EQUIPPED WITH ANDROID SYSTEM ..... 19

5. RESTORING FACTORY SETTINGS ........................................................................ 19

5.1. Software factory reset ........................................................................................ 19

5.2. Hardware factory reset ...................................................................................... 19

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

5

1. FOREWORD INFORMATION

1.1. General Characteristics

• Sensor resolution: 2 megapixels

• Mechanical IR cut filter, IR operation capability

• Min. Illumination from 0 lx with IR LED on

• Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions

• Digital Noise Reduction (DNR)

• Lens with remote focal and focus control, f=2.8mm/F=1.85

• Built-in LED illuminator: 1 pc LED

• Compression of video stream: H.264/H265/MJPEG

• Max video processing resolution: 1920 x 1080

• Three independently configurable streams

• Stream parameters: compression, resolution, speed and quality defined individually for each video

stream

• RTP/RTSP protocol support for video transmission

• Two-way audio transmission

• Compression of audio stream: G.711

• Wireless WiFi and wired LAN connections

• Alarm input and output

• Hardware motion detection

• Hardware sabotage detection (lens shade)

• Built-in webserver: camera configuration through the website

• Wide range of responses to alarm events: e-mail with attachment, saving file on FTP server,

activation of alarm output

• Four privacy zones

• Eight definable Region of Interest

• Power supply: 12VDC, PoE (Power over Ethernet 802.3af)

Information

The manufacturer reserves the right to printing errors and technical specifications changes

without prior notice.

FOREWORD INFORMATION

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

6

TECHNICAL SPECIFICATION

1.2. Technical specification

IMAGE

Image Sensor 2 MPX CMOS sensor 1/2.7” SmartSens

Number of Eecve Pixels 1936 (H) x 1096 (V)

Min. Illuminaon

0.007 lx/F1.2 - color mode,

0 lx (IR on) - B/W mode

Electronic Shuer auto: 1 s ~ 1/100000 s

Digital Slow Shuer (DSS) up to 1 s

Digital Noise Reducon (DNR) 3D

Defog Funcon (F-DNR) yes

Back Light Compensaon (BLC) yes

Reducon of image icker (Anicker) yes

LENS

Lens Type standard, f=2.8 mm/F1.85

DAY/NIGHT

Switching Type mechanical IR cut lter

Switching Mode auto, manual, me

Switching Level Adjustment yes

Switching Delay 2 ~ 120 s

Visible Light Sensor yes

NETWORK

Stream Resoluon

1920 x 1080 (Full HD), 1280 x 720 (HD), 704 x 576, 480 x 240,

352 x 288 (CIF)

Frame Rate 25 fps for each resoluon

Mulstreaming Mode 3 streams

Video/Audio Compression H.264, H.265, MJPEG/G.711

Number of Simultaneous Connecons max. 4

Bandwidth 8 Mb/s in total

Network Protocols Support

HTTP, TCP/IP, IPv4/v6, UDP, HTTPS, FTP, DHCP, DDNS, NTP, RTSP,

UPnP, QoS, IEEE 802.1X, PPPoE, SMTP

ONVIF Protocol Support Prole S

Camera Conguraon

from Internet Explorer browser

languages: Polish, English, Russian, and others

Compable Soware NMS

Mobile applicaons SuperLive Plus (iPhone, Android)

WIFI

Network standard IEEE802.11b, g, n

Band 2.4GHz

Security WEP, WPA-PSK/WPA2-PSK

Transmission range up to 50 m

Antenna built-in, omnidireconal

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

7

TECHNICAL SPECIFICATION

The declared range of the WiFi network is based on laboratory research and relates to open

spaces. It should be noted, that the materials used for the construction of houses and flats, wall

thickness and electromagnetic field conditions in the immediate surroundings may affect the

range of the network.

OTHER FUNCTIONS

Privacy Zones 4

Moon Detecon yes

PIR detector range up to 7 m

Region of interest (ROI) 3

Video Content Analysis (VCA) line cross, zone entrance

Image Processing

90˚ image rotaon, 180˚ image rotaon, mirror eect, corridor

mode, vercal ip, horizontal ip

Prealarm/Postalarm up to 6 s/up to 120 s

System Reacon to Alarm Events

e-mail with aachment, saving le on FTP server, saving le on SD

card, alarm output acvaon

IR LED

LED Number 1

Range 10 m

Angle 120°

Smart IR yes (soware support)

INTERFACES

Audio Input/Output built-in microphone/speaker

Alarm Input/Output 1 (NO/NC)/1 relay type

Network Interface

1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Wireless (WiFi)

Memory Card Slot microSD - capacity up to 128GB

INSTALLATION PARAMETERS

Dimensions (mm)

63 (W) x 109 (H) x 30 (L)

with bracket: 72 (W) x 130 (H) x 72 (L)

Weight 0.2 kg

Enclosure plasc, black and white, wall mount/base in-set included

Power Supply PoE, 12 VDC

Surge protecon TVS 4000 V

Power Consumpon 2 W,3 W (IR on)

Operang Temperature -10°C ~ 45°C

Humidity max. 95%, relave (non-condensing)

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

8

START-UP AND INITIAL CONFIGURATION

1.3. Camera dimensions

1.4. Package contents

After you open the package make sure that the following elements are inside:

• IP camera

• Accessories bag

• Quick start guide

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with. If you have any

problems understanding the manual, please contact the AAT. Self-assembly and commissioning

of the camera is possible, provided that the person has basic knowledge of computer networks

and the use of appropriate tools.

Caution:

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

9

START-UP AND INITIAL CONFIGURATION

2. START-UP AND INITIAL CONFIGURATION

2.1. Description of camera components and connectors

2.2 Power supply connection

When powering the camera from an external 12VDC power supply, make sure that it has the correct

parameters and the power supply plug - the correct polarity. The use of a power source with

inappropriate parameters may result in incorrect operation or damage of the camera.

1 Lens 9 LAN socket

2 IR LED (infrared illuminator) 10 Loudspeaker

3 Microphone 11 Block of alarm input/output connectors

4 PIR detector 12 12VDC power socket

5 Power indicator 13 Reset/WPS button

6

Network connection indicator:

flashes when connecting via RJ45 cable

14 Memory card slot

7

Alarm input alarm signaling.

Signaling connection to a WiFi network

using WPS

15 Camera position adjustment

8 Light sensor 16 Base

Center pin: +12V

GND

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

10

START-UP AND INITIAL CONFIGURATION

The camera can also be powered via an RJ45 network connector, using PoE (IEEE 802.3af)

technology. Please, use a network switch or an IEEE 802.3af compliant PoE power supply to power

the camera through the PoE.

2.3. Connection of alarm input/output

The camera has one alarm input and output. The alarm input is used to connect a device such as a

motion detector, button, reed switch or photocell. Violation of the input will trigger the alarm and

activate the previously programmed action.

The alarm output enables connection of an external siren and implementation of automatic control

functions, such as switching on lighting.

Podłączenie wejścia alarmowego

Podłączenie wyjścia alarmowego

I Alarm input, configurable: NC or NO

G Ground (common terminal)

O Alarm output terminal, (12VDC/0.1A maks.)

Caution:

It is forbidden to use – as the camera power source – PoE equipment (adapters, etc.) not

compatible with IEEE 802.3af standard (items called “passive PoE power supply”). Damages

that results from the usage of improper power supply source are not covered by the warranty.

trigger contact

signaling device

maximum load 0.1A

signaling device power

supply 12VDC max.

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

11

START-UP AND INITIAL CONFIGURATION

2.4. Connecting the LAN network cable

To connect to the camera via a wired LAN, insert the LAN cable plug into the LAN socket so that the

plug latch clicks into the socket. Connect the other end of the cable to your switch / router.

2.5. Camera mounting

The camera design allows flexible selection of the place of attachment / installation. The camera can

work when placed on any flat surface or be hung using mounting holes in the foot.

To mount the camera in a hanging position, we recommend you follow the following guidelines:

• Place the template where you want to install the camera. Then drill the holes according to the

template.

• Insert the dowels into the holes and tighten the screws. The screws should protrude a few

millimeters above the wall surface.

• Route and connect the cables to the camera.

• Hang the camera by the mounting base on the screws and make sure it is securely fastened.

Then adjust the camera position.

Caution:

The camera is designed for indoor use in living quarters. Using it outdoors, or in rooms with

high humidity such as swimming pools, bathrooms, laundries, etc. may cause the camera to

malfunction or damage.

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

12

2.6. Starting the camera

2.6.1 Starting with connecting the camera to a wired LAN network

To start the camera, connect the Ethernet cable to the camera's network socket, and the other end to the

switch or router. If your switch or router is not a PoE device, you should also connect a 12VDC power

supply to the camera. The following schemes may help:

• Wired connection using a PoE switch or router:

• Wired connection using a switch or router without PoE and 12VDC power supply:

After making connections and starting the camera (which takes about 2 minutes) it is possible to

connect to the camera. Use Internet Explorer to connect to the camera.

After entering the default address in the browser's address bar, wait for the login page to appear. If the

page did not appear, and the browser displayed a connection error message "This page cannot be

displayed", check the compatibility of the IP addresses of the camera and the network in which it will

work and make the appropriate configuration.

To configure the network settings you will need the "NMS IP Tool" application, which can be

downloaded from the product page at www.novuscctv.com.

START-UP AND INITIAL CONFIGURATION

PC

Camera

Data transmission

Switch or router with PoE

Power supply and data

transmission

Camera

PC

Data transmission

Switch or router without PoE

Data transmission

Power supply

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

13

START-UP AND INITIAL CONFIGURATION

• Połączenie wykorzystujące zewnętrzne zasilanie kamery i kabel ethernetowy

2.5. Konfiguracja parametrów przy użyciu przeglądarki internetowej

Domyślne ustawienia sieciowe dla kamery to:

1. Adres IP = 192.168.1.200

2. Maska sieci - 255.255.255.0

3. Brama - 192.168.1.1

4. Nazwa użytkownika - root

5. Hasło - pass

Znając adres IP kamery należy ustawić adres IP komputera w taki sposób aby oba urządzenia

pracowały w jednej podsieci (dla adresu IP kamery 192.168.1.200 jako adres IP komputera PC

możemy ustawić adres z zakresu 192.168.1.0 - 192.168.1.254, np.: 192.168.1.60). Niedopuszczalne jest

ustawianie adresu komputera takiego samego jak adres kamery.

Wykorzystując połączenie przez przeglądarkę internetową Internet Explorer lub oprogramowanie NMS

należy ustawić docelową konfigurację sieciową (adres IP, maskę sieci, bramę, serwery DNS)

lub włączyć tryb pracy DHCP pozwalający na pobranie adresu IP z serwera DHCP (wymagany jest

wówczas działający serwer DHCP). W przypadku korzystania z serwera DHCP należy upewnić się

co do długości okresu dzierżawy adresu IP, jego powiązania z adresem MAC kamery IP w celu

uniknięcia zmiany lub utraty adresu IP w czasie pracy urządzenia lub chwilowej awarii sieci / serwera

DHCP. Należy pamiętać że po zmianie adresu IP kamera zostanie zresetowana i trzeba wpisać nowy

adres w przeglądarce internetowej. Po konfiguracji ustawień sieciowych pozwalających na

bezkonfliktową pracę urządzenia, kamerę IP możemy podłączyć do sieci docelowej.

2.6.1.1 Configuring network settings using a DHCP server

After launching the application and searching for the camera, check the box next to its address. Enter

the login details in the network settings change panel, select "DHCP" in the "IP mode" window (leave

the other fields unfilled) and press the "IP Change" button. After a while, the camera will start with the

new IP address given by the DHCP server built into the router/switch.

2.6.1.2 Manual configuration of network settings

We check the IP address in the computer's network settings. Then select a new IP address for the

camera, check if it is not busy (eg using the "ping" command at the command prompt) and change the

camera address in the application. After a while, the camera will start with the new IP address assigned.

After changing the camera's IP address, you should be able to connect to it using Internet Explorer.

Further configuration of the camera is carried out via its web panel (see chapter 3 on page 15).

2.6.2 Starting with connecting the camera to a WiFi network

To start the camera, connect a 12VDC power supply.

After the camera starts up (which takes up to 2 minutes), press the WPS button on the router. Then,

within two minutes, press the RESET / WPS button on the camera. The process of connecting the

camera to the WiFi network begins, which is signaled by continuous lighting of the "Alarm" LED.

After successful connection the diode goes out. Connection error is indicated by flashing of this LED.

To check which IP address has been assigned to the camera, start the "NMS IP Tool" application, or

connect to the router configuration page and check the camera address in the list of DHCP clients.

Configuring the camera's IP address using a DHCP server is quick and convenient. However, at

a later stage of camera use it is recommended to set a static IP address in it. This will prevent

connection loss if the DHCP server changes the camera address.

The default camera network settings are:

IP address: 192.168.1.200, network mask: 255.255.255.0, login details: login - root, password -

pass

Caution:

Do not connect the RJ45 network cable. Connecting a network cable disables the WiFi network.

Caution:

Detailed information about network settings, WPS button operation and assigned address

verification should be available in the router's user manual.

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

14

START-UP AND INITIAL CONFIGURATION

2.7 Security recommendations for network architecture and configuration

WARNING!

Below are shown security recommendations for network architecture and configuration of

CCTV systems that are connected to the Internet to reduce the risk of unauthorized interference

with the system by a third party.

1. Absolutely change the default passwords and user names (if the device gives this possibility) of

all applied network devices (recorders, cameras, routers, network switches, etc.) to the

severely complexity password. Use lowercase and uppercase letters, numbers, and special characters

if there is such possibility.

2. Depending on the available functionality in the order to restrict access to the used network devices at

the administrator account level, it is recommended to configure the users accounts accordingly.

3. Do not use DMZ function (Demilitarized zone) in your router. Using that function you open the

access to recorder system from the Internet on all ports, which gives possibility for an unauthorized

interference with the system.

Instead of DMZ use port forwarding redirect only the ports which are necessary for the performance

of the connection (detailed information about ports of communication in different models of recorders,

cameras, etc. can be found in the operating instructions).

4. Use routers with firewall function and make sure it is enabled and properly configured.

5. It is recommended to change the default network communication port numbers of used devices

if there is such possibility.

6. If used network devices has a UPnP feature and it is not used, turn it off.

7. If used network devices has a P2P feature and it is not used, turn it off.

8. If used network devices support HTTPS protocol for connection, it is recommended to use it.

9. If used network devices support IP filtering for authorized connections function, it is recommended

to use it.

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

15

3. CONNECTING FROM A PC WITH A WEB BROWSER

3.1. First connection to the camera

After connecting and configuring the camera, you can connect to it. Enter the camera's IP address in the

address bar of Internet Explorer. After the connection is established, a message will be displayed

informing you that there is no ActiveX add-on required for proper camera operation.

To download it, click on the "Here" link. The "NetIPCamera.exe" download window will be displayed.

Then click the "Run" button.

When the add-on installer window appears, click "Install" button and install the add-on, following the

information displayed by the installer.

START-UP AND INITIAL CONFIGURATION

The installation of the add-on is one-off, it takes place during the first connection. However, on

subsequent connections, especially after changing the IP address, the browser may display a

security alert:

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

16

WWW INTERFACE - WORKING WITH A CAMERA

3.2. Login screen

After connecting to the camera, the login screen will be displayed. Enter the login and password in

the login fields. You can also change the language of the camera interface.

The “Remember me” option allows you to login to the camera without entering a password. For

security reasons, using this option is not recommended.

After logging in, a password change window will appear.

For security reasons, it is recommended to change the default password to a highly complicated one

in this step. If you do not intend to change the password at this time, after pressing "OK" the user

will be taken to the remote preview window. The "Cancel" button interrupts the process of logging

into the camera.

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

17

WWW INTERFACE - WORKING WITH A CAMERA

3.3. Remote view window

1. Stream selection buttons for display in the remote preview window

2. Button for selecting the stream buffering level. Available options: Real-time (smallest buffer),

Balanced (default option) and Fluent (maximum buffer).

3. Preview window. Double-clicking the left mouse button on the preview window enables and

disables the display of the image on the full screen.

4. Buttons for selecting the operating mode and configure the camera:

Live - enables preview live stream

Config - displays the configuration panel camera

Search - displays the playback panel of recordings from the memory card

Logout - log off the current user

1

6

7

2 3

4

5

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

18

5. Notification Area. Icons displayed here are informing about activated alarms. Activation of a given

alarm is signaled by a cyclical color change of the corresponding icon, from black to red.

6. Buttons to set the size and aspect ratio

7. Additional features control icons

WWW INTERFACE - WORKING WITH A CAMERA

- enables/disables live view

- enables/disables the audio transmission from the computer to the camera

- enables/disables audio transmission from the camera to the computer

- alarm input actiwation

- scene change alarm

- motion detection alarm

- PIR alarm

- line crossing alarm

- intrusion alarm

- abnormal color alarm

- SD card recording icon. Black means that the camera is ready to record on the camera,

but recording is inactive. Red indicates recording is on.

- abnormal clarity alarm

- original size

- maintains the aspect ratio

- adapts to the window

- enables full screen

NVIP-2Q-6101/PIR/W Quick start guide ver. 1.1.1

19

4. CONNECTION FROM A DEVICE EQUIPPED WITH ANDROID SYSTEM

To connect to the camera from an Android device, you need to download from the Google store and

install the SuperLive Plus application.

5. RESTORING FACTORY SETTINGS

5.1 Software factory reset

The camera allows to reset its settings to the factory defaults. To restore the camera settings to the

default settings, go to the “Backup and restore” tab (Config -> Maintenance -> Backup and restore).

Then in the "Default Settings" line select the camera options and functions whose settings are not to be

changed and press the “Load default” button.

Resetting to factory settings is also possible with the “NMS IP tool” application. To restore the factory

settings using this application, right-click anywhere in the row with the address of the camera found

and select “Restore default configuration”. Then disconnect and reconnect the camera's power supply

within 30 seconds. The camera will start with the default settings.

5.2 Hardware factory reset

To reset the camera to the factory default settings, use the RESET button located on the back. Press and

hold it for about 5 seconds.

After about 30 seconds you will be able to reconnect to the camera at the default IP address.

CONNECTION FROM A DEVICE EQUIPPED WITH ANDROID SYSTEM

A description of all camera functions is included in the full user manual on the product page at

www.novuscctv.com

- zooming in image

- takes a screenshot and saves to your PC

- enables/disables the recording of video stream on a PC

- zooming out image

11.02.2020 MB, MK v1.1.1

AAT SYSTEMY BEZPIECZEŃSTWA SP. Z O.O.

431 Pulawska St., 02-801 Warsaw, Poland

tel.: +4822 546 07 00, fax: +4822 546 07 59

www.novuscctv.com

Strona jest ładowana ...

Novus NVIP-2Q-6101/PIR/W Instrukcja obsługi

Novus NVIP-2Q-6101/PIR/W Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty