Novus NVR-6304P4-H1 Instrukcja obsługi

U s e r ’s m a n u a l

(s h ort )

NVR-6332-H2

NVR-6316-H1

NVR-6308P8-H1

NVR-6304P4-H1

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

2

IMPORTANT SAFEGUARDS AND WARNINGS

EMC (2004/108/EC) and LVD (2006/95/EC ) Directives CE Marking

Our products are manufactured to comply with requirements of following directives and national regulations implementing the

directives:

Electromagnetic compatibility EMC 2004/108/EC; Low voltage LVD 2006/95/EC with further amendment. The Directive applies

to electrical equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as 75VDC and

1500VDC.

WEEE Directive 2002/96/EC Information on Disposal for Users of Waste Electrical and Electronic Equipment

This appliance is marked according to the European Directive on Waste Electrical and Electronic Equipment (2002/96/EC)

and further amendments. By ensuring this product is disposed of correctly, you will help to prevent potential negative

consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling

of this product.

The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be treated as

household waste. It shall be handed over to the applicable collection point for the waste electrical and electronic equipment

for recycling purpose. For more information about recycling of this product, please contact your local authorities, your

household waste disposal service or the shop where you purchased the product.

RoHS Directive 2002/95/EC

Concerning for human health protection and friendly environment, we assure that our products falling under RoHS Directive

regulations, regarding the restriction of the use of hazardous substances in electrical and electronic equipment, were designed and

manufactured in compliance with mentioned regulation. Simultaneously, we claim that our products were tested and do not contain

hazardous substances exceeding limits which could have negative impact on human health or natural environment.

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed for self installation in

households by individuals without technical knowledge. The manufacturer is not responsible for defects and damages

resulted from improper or inconsistent with user ’ s manual installation of the device in the system.

ATTENTION!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT PROVISIONED FOR THE GIVEN PRODUCT IN ITS USER ’ S MANUAL AND

OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR THAT ARISES FROM THE NORMAL APPLICATION OF THE PRODUCT, ITS

MANUFACTURER MUST BE CONTACTED OR THE RESPONSIBILITY OF THE MANUFACTURER FOR THE RESULTS OF SUCH AN

ACTION SHELL BE EXCLUDED.

1. Prior to undertaking any action please consult the following manual and read all the safety and operating

instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct influence on

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

3

FOREWORD INFORMATION

1. FOREWORD INFORMATION

1.1. Network recorder’s technical data

NVR-6332-H2

VIDEO

IP Cameras 32 channels at 2592 x 1944 resolution (video + audio)

Supported Cameras/Protocols NOVUS, ONVIF

Supported Resolution max. 2592 x 1944

Compression H.264, H.264+, H.265

Monitor Output main (split screen, full screen, sequence): 1 x HDMI, 1 x VGA (up to 2 monitors simultaneously)

Dualstreaming Support yes*

AUDIO

Audio Output 1 x line-out (RCA) 1 x HDMI

RECORDING

Recording Speed

960 kl/s (32 x 30 kl/s dla 2592 x 1944)

Stream Size

256 Mb/s in total from all cameras

Recording Mode time-lapse, triggered by: manual, alarm input, motion detection

Prealarm/Postalarm

up to 5 s/up to 600 s

DISPLAY

Display Speed 960 fps (32 x 30 fps)**

PLAYBACK

Playback Speed 480 fps (16 x 30 fps for 2592 x 1944) **

Recorded Data Search by date/time, events

BACKUP

Backup Methods USB port (HDD or Flash memory), network

Backup File Format AVI

STORAGE

Internal storage for recording available mount: 2 x HDD 3.5” 6 TB SATA

Total Capacity 12 TB

ALARM

Motion Detection supports camera’s motion detection*

System Reaction to Alarm Events buzzer, e-mail, recording activation, PTZ

NETWORK

Network Interface 1 x Ethernet - RJ-45 interface, 10/100/1000 Mbit/s

Network Protocols Support HTTP, TCP/IP, IPv4, DHCP, DNS, DDNS, NTP, UPnP, SMTP

ONVIF Protocol Support Profile S (ONVIF 2.2 or higher)

PC/MAC Software NVR-6000 Viewer/-

Smartphone Software SuperLive Plus (iPhone, Android)

Max. Number of Connections

with NVR 1

Bandwidth 256 Mb/s in total to all client workstations

PTZ

PTZ Functions pan/tilt/zoom, preset commands*

AUXILIARY INTERFACES

USB Ports 1 x USB 2.0, 1 x USB 3.0

OPERATING SYSTEM

Operating System Linux

Operation Mode triplex

OSD languages: Polish, English, others

Control PC mouse and IR remote controller (in-set included), network

System Diagnostic automatic control of: HDDs, network, camera connection loss

Security password protection, IP filtering, MAC filtering

INSTALLATION PARAMETERS

Dimensions (mm) 380 (W) x 53 (H) x 268 (D)

Weight 1.5 kg (without HDD)

Power Supply 100 ~ 240 VAC

Power Consumption 40 W (with 2 HDDs)

Operating Temperature -10°C ~ 50°CEdit feature

* Function depends on communication protocol, for details please check compatibility table ** Available with dual streaming mode.

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

4

FOREWORD INFORMATION

NVR-6316-H1

VIDEO

IP Cameras 16 channels at 2592 x 1944 resolution (video + audio)

Supported Cameras/Protocols NOVUS, ONVIF

Supported Resolution max. 2592 x 1944

Compression H.264, H.264+, H.265

Monitor Output main (split screen, full screen, sequence): 1 x HDMI

Dualstreaming Support yes*

AUDIO

Audio Output 1 x line-out (RCA) 1 x HDMI

RECORDING

Recording Speed Up to 480 kl/s (16 x 30 kl/s for 2592 x 1944)

Stream Size 80 Mb/s in total from all cameras

Recording Mode time-lapse, triggered by: manual, motion detection

Prealarm/Postalarm up to 5 s/up to 600 s

DISPLAY

Display Speed 480 fps (16 x 30 fps)**

PLAYBACK

Playback Speed Up to 480 fps (16 x 30 fps for 2592 x 1944) **

Recorded Data Search by date/time, events

BACKUP

Backup Methods USB port (HDD or Flash memory), network

Backup File Format AVI

STORAGE

Internal storage for recording available mount: 1 x HDD 3.5” 6 TB SATA

Total Capacity 6 TB

ALARM

Motion Detection supports camera’s motion detection*

System Reaction to Alarm Events buzzer, recording activation, PTZ, e-mail with atatchment

NETWORK

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Network Protocols Support HTTP, TCP/IP, IPv4, DHCP, DNS, DDNS, NTP, UPnP, SMTP

ONVIF Protocol Support Profile S (ONVIF 2.2 or higher)

Smartphone Software SuperLive Plus (iPhone, Android)

Max. Number of Connections with NVR 2

Bandwidth 80 Mb/s in total to all client workstations

PTZ

PTZ Functions pan/tilt/zoom, preset commands*

AUXILIARY INTERFACES

USB Ports 1 x USB 2.0, 1 x USB 3.0

OPERATING SYSTEM

Operating System Linux

Operation Mode triplex

OSD languages: Polish, English, others

Control PC mouse and IR remote controller (in-set included), network

System Diagnostic automatic control of: HDDs, network, camera connection loss

Security password protection, IP filtering, MAC filtering

INSTALLATION PARAMETERS

Dimensions (mm) 300 (W) x 52 (H) x 248 (D)

Weight 1.5 kg (without HDD)

Power Supply 100 ~ 240 VAC

Power Consumption 20 W (with 1 HDD)

Operating Temperature -10°C ~ 50°CEdit feature

* Function depends on communication protocol, for details please check compatibility table ** Available with dual streaming mode.

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

5

FOREWORD INFORMATION

NVR-6304P4-H1 / NVR-6308P8-H1

VIDEO

IP Cameras

4 channels at 2592 x 1944 resolution (video + audio) 8 channels at 2592 x 1944 resolution (video + audio)

Supported Cameras/Protocols

NOVUS, ONVIF

Supported Resolution

max. 2592 x 1944

Compression

H.264, H.264+, H.265

Monitor Output

main (split screen, full screen, sequence): 1 x HDMI

Dualstreaming Support

yes*

AUDIO

Audio Output

1 x line-out (RCA) 1 x HDMI

RECORDING

Recording Speed

120 kl/s (4 x 30 kl/s dla 2592 x 1944) 240 kl/s (8 x 30 kl/s dla 2592 x 1944)

Stream Size

80 Mb/s in total from all cameras 50 Mb/s in total from all cameras

Recording Mode

time-lapse, triggered by: manual, motion detection

Prealarm/Postalarm

up to 5 s/up to 600 s

DISPLAY

Display Speed

120 fps (4 x 30 fps)** 240 fps (4 x 30 fps)**

PLAYBACK

Playback Speed

120 fps (4 x 30 fps for 2592 x 1944) ** 240 fps (4 x 30 fps for 2592 x 1944) **

Recorded Data Search

by date/time, events

BACKUP

Backup Methods

USB port (HDD or Flash memory), network

Backup File Format

AVI

STORAGE

Internal storage for recording

available mount: 1 x HDD 3.5” 6 TB SATA

Total Capacity

6 TB

ALARM

Motion Detection

supports camera’s motion detection*

System Reaction to Alarm Events

buzzer, recording activation, PTZ, e-mail with atatchment

NETWORK

Network Interface

1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

4 x Ethernet PoE - RJ-45 interface, 10/100 Mbit/s 8 x Ethernet PoE - RJ-45 interface, 10/100 Mbit/s

Network Protocols Support

HTTP, TCP/IP, IPv4, DHCP, DNS, DDNS, NTP, UPnP, SMTP

ONVIF Protocol Support

Profile S (ONVIF 2.2 or higher)

Smartphone Software

SuperLive Plus (iPhone, Android)

Max. Number of Connections with NVR

2

Bandwidth

40 Mb/s in total to all client workstations 80 Mb/s in total to all client workstations

PTZ

PTZ Functions

pan/tilt/zoom, preset commands*

AUXILIARY INTERFACES

USB Ports

2 x USB 2.0

OPERATING SYSTEM

Operating System

Linux

Operation Mode

triplex

OSD

languages: Polish, English, others

Control

PC mouse and IR remote controller (in-set included), network

System Diagnostic

automatic control of: HDDs, network, camera connection loss

Security

password protection, IP filtering, MAC filtering

INSTALLATION PARAMETERS

Dimensions (mm)

300 (W) x 52 (H) x 248 (D)

Weight

1.16 kg (without HDD)

Power Supply

100 ~ 240 VAC

Power Consumption

12 W (with 1 HDD) + 36 W PoE 20 W (with 1 HDD) + 100W PoE

Operating Temperature

-10°C ~ 50°CEdit feature

* Function depends on communication protocol, for details please check compatibility table ** Available with dual streaming mode.

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

6

FOREWORD INFORMATION

1.2. Main characteristics

 Supports resolution up to 2592 x 1944

 Supported protocols: ONVIF

 Recording up to 2592 x 1944

 Recorded stream size up to 256 Mb/s in total from all cameras (for NVR-6332-H2)

 Internal HDDs mount up to 2 (for NVR-6332-H2)

WARNING!

ONVIF protocol support was verified with IP cameras based on ONVIF ver. 2.2 and compatible

with the "PROFILE S".

Implementation of the ONVIF protocol by different manufacturers may vary by some functions,

which can make them work improperly or not in accordance with expectation. AAT HOLDING

Company is not responsible for incompatibility problems resulting from cameras of other brands

than NOVUS, which are using ONVIF protocol. If you are using ONVIF protocol cameras other

than NOVUS brand it is recommended to test each time whether required functions work

correctly.

1.3. Package contents

Unpack the device carefully. After unpacking, please ensure that package contains the following items:

 Network Video Recorder

 USB Mouse

 Remote control

 Power supply

 User’s manual (short)

If any of the elements has been damaged during transport, pack all the elements back into the original

packaging and contact your supplier.

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

7

STARTING THE DEVICE

2. STARTING THE DEVICE

2.1 Electrical connection and other back panel elements.

NVR-6304P4-H1

NVR-6308P8-H1

1. .AUDIO IN: Audio mono inputs to connect microphones*.

2. VGA: Main monitor connectors, use the D-SUB VGA cable to connect monitor.

3. HDMI: Main monitor connectors, use the HDMI cable to connect monitor.

4. USB: USB port for external Flash memory and other USB devices.

5. LAN: RJ-45 connector port to connect to the local network and internet.

6. PoE LAN: RJ-45 connector ports with PoE support for IP cameras

7. POWER SOCKET: To plug in the 48V power cord

8. POWER SW: NVR power switch.

9. AUDIO OUT : Audio output

* Will be available in the future.

6

5

4

3

2

1

8

9

7

6

5

4

3

2

1

9

8

7

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

8

STARTING THE DEVICE

NVR-6316-H1

1. ALARM IN/OUT: Alarm in/out block

2. POWER SOCKET: To plug in the 12V power cord

3. HDMI: Main monitor connectors, use the HDMI cable to connect monitor.

4. USB: USB port for external Flash memory and other USB devices.

5. LAN: RJ-45 connector port to connect to the local network and internet.

6. .AUDIO IN: Audio mono inputs to connect microphones*.

7. AUDIO OUT : Audio output

* Will be available in the future.

NVR-6332-H2

1. POWER SOCKET: To plug in the 12V power cord

2. LAN: RJ-45 connector port to connect to the local network and internet.

3. VGA: Main monitor connectors, use the D-SUB VGA cable to connect monitor.

4. HDMI: Main monitor connectors, use the HDMI cable to connect monitor

5. LAN: RJ-45 connector port to connect to the local network and internet.

6. .AUDIO IN: Audio mono inputs to connect microphones*.

7. AUDIO OUT : Audio output

* Will be available in the future.

6

5

4

3

2

1

7

6

5

4

3

5

2

7

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

9

STARTING THE DEVICE

2.2 HDD mounting

Novus 6000 NVRs supports 2 internal SATA HDD (model NVR-6332-H2) or 1 internal SATA HDD

(models NVR-6304P4-H1, NVR-6308P8-H1, NVR-6316).

WARNING!

In order to find information regarding the compatible models of HDDs and their maximum

capacities, please contact Novus distributor or check the information presented at

www.novuscctv.com. AAT HOLDING Company is not responsible for any problems from using

not recommended hard drives.

The list of compatible HDDs contains all the HDDs that can be used with a given DVR including

HDDs designed for office use - so called desktop disks. However, due to the fact that reliability of

the recording process and data safety are paramount factors of any CCTV system, we strongly

advise to use HDDs designed for continuous (24/7) operation.

You need to format disks if they were used in a different device. All data saved on HDD prior to

format will be lost.

Installation HDD in NVR-6304P4-H1, NVR-6308P4-H1,NVR-6316

In order to mount HDD, please loose the screws in the locations shown on the picture below and

remove the cover.

WARNING: !

Before removing cover unplug the power cord from the NVR. When NVR is turned on before

disconnecting the power cord, shut down the recorder using the NVR menu.

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

10

STARTING THE DEVICE

After enclosure, mount the disk using mounting screws (4 pcs.), And then connect the power cord and

signal.

After connecting the hard drive mount the cover start the NVR to check and format the hard drive.

CAUTION:

If you use the disk was used in another device, it is necessary to format it before using.

Formatting the drive erase all the data from disk. All drives in the recorder should be exactly the

same type.

Installation HDD in model NVR-6632

In order to mount HDD, please loose the screws in the locations shown on the picture below and

remove the cover recorder pushing it to the back and then lifting up.

After enclosure, mount the disk or disks using mounting screws (4 pieces on the disc), then connect the

power cord and signal cable.

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

11

STARTING THE DEVICE

2.3. Connecting the power supply.

Please connect provided power cord in the rear power port of the NVR like depicted below.

To start the unit turn on the power switch on back panel (NVR-66304P4-H1, NVR-66308P8-H1 only).

Initialization lasts approximately 60 seconds. During this time executing any device functions and

pressing any buttons is prohibited. To shut down the device please use the menu.

CAUTION:

Make connection when the power is not applied and the power switch is turned off.

Do not place the power cord under the carpet or rug. The power cord is usually earth-grounded.

However, even if it's not earth-grounded, never modify it on your own for earth-grounding.

Make sure that power adapter is placed near of NVR and secured from accidental disconnection.

If the device was brought from a location with lower temperature, please wait until it reaches the

temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

12

2.4. Connecting monitor

This product supports following interfaces for main monitor: HDMI, VGA.

For HDMI following resolutions are supported: 1280x1024, 1920x1080 i 3840x2160.

2.5. Connecting camera and Network

NVRs NVR-6304P4-H1 and NVR-6308P8-H1 have built-in 4/8 PoE ports RJ-45 with PoE support,

which can be used for connecting cameras. Please notice that the Ethernet connection is effective

within 100 meter distance. To connect IP cameras please connect cables like on image and follow the

described below.

We recommend that you configure the camera before connecting to a recorder, as described the

manual camera. Please note that cameras have addressed the unique IP address supported by the

recorder. Recorders with built-in PoE switches use a different address from the cameras connected via

the built-in switch and another to connect to a device connected via the LAN port.

Connecting cameras and network recorders NVR-6304P4-H1 / NVR-6308P8-H1

STARTING THE DEVICE

IP CAMERAS

NOVUS NVR

INTERNET

PC

NETWORK SWITCH

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

13

Connecting cameras and network recorders NVR-6316-H1, NVR-6332-H2

Note: In order to ensure stability and protection against overload and unauthorized access, we

recommend separating the network monitoring of LANs used by users.

Before configuring the connection of the cameras in the recorder, we recommend using a PC to

configure the cameras according to the instructions of the camera.

2.6. Connecting external devices

 Connecting audio ports

Audio output signal normally are above 200mV 1kΩ. You can connect to it the audio amplifier with

the external speakers.

 Connecting USB devices

NVR has 1 x USB 2.0 port on front and one 1 x USB 2.0 on back (NVR-6332-H2 have 3.0 USB port

on back panel) . They could be used for connecting external Flash memory, mouse connection and

other USB compatible devices. To connect storage memory it is recommended to use port USB 3.0

STARTING THE DEVICE

NETWORK SWITCH

INTERNET

PC

NOVUS NVR

IP CAMERAS

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

14

 Connecting alarms ports

NVR-6316-H1 has local alarm input and output. To connect alarm input please refer image below

An example of connecting the sensor to the alarm input 1.

STARTING THE DEVICE

NO COM

ALARM

Power

source

ALARM

IN1 IN2 IN3 IN4

GND SENSOR

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

15

NVR OPERATING

3. NVR OPERATING

3.1. Front panel description

1. LED Diodes for monitoring NVR activity.

- REC - monitors recording activity

- NET - monitors networking activity

- PWR - activities when power is on

2. USB USB 2.0 port for external Flash memory and mouse connection.

.

3.2. Controlling via USB mouse

It is possible to control NVR via an USB mouse connected to the USB port. Double-click on any

camera in split screen display mode switches the display to full-screen mode. Subsequent double-click

returns to previous display mode. Move cursor to the top or click the right key of mouse to bring up

MAIN MENU and select START icon.

Certain positions allow to select them via mouse scroll. Depending on NVR operating mode, pressing

RMB displays a corresponding function menu.

3.3. System operations

To start NVR plug power cable and switch on power button (NVR-6308P8-H1,NVR-6304P4-H1). The

power led turns on. After booting, the video output default is multi-window output mode.

Note:

If the currently selected NVR menu language is not as expected, to change it, please follow the

procedure described in chapter 4.3 of this manual.

1

2

1

2

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

16

To unlock the DVR menu, press the button at the bottom left of the screen.

After clicking on button click-on “LOGIN”

Then login in entering password in PASSWORD field (default password for user root is “pass”)

and then click-in login button

NVR OPERATING

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

17

3.4. Startup configuration

Prior to using NVR for the first time, initial setup is strongly advised. Before you connect the IP

cameras to the NVR, please set up network and stream parameters of IP cameras in the right way.

Note:

For suggested values for IP camera setting please refer to the “Cameras Capability Table” available

on the www.novuscctv.com website. If you set wrong values some problems may appear: the NVR

cannot search the IP camera, the stream cannot be connected, the image is not fluent, the image quality

is bad and so on.

In case of first NVR start WIZARD SETUP menu window will occur (if function wasn’t disabled

earlier). To configure NVR please follow procedure like below, after finishing all the steps you’ll be

ready to work:

Provide username and password and click on NEXT button so start wizard.

NVR OPERATING

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

18

I. Network Settings : This menu allows to set up networking. Default IP configuration is

192.168.1.100 netmask 255.255.255.0 . For NVRs with build in PoE switches (NVR-6304P4-H1 i

NVR-6308P8-H1) it is necessary to configure IP address for switch in INTERNAL ETHERNET

PORT SECTION. Please note that IP subnet for the ETHERNET PORT 1 and INTERNAL

ETHERNET PORT were different. In cases where it is necessary to NVRa connection to the Internet

(for remote access, email sending, etc.), Configure the following parameters: Gateway, Primary and

Secondary DNS. You can also enable DHCP mode allows you to download an IP address from a

DHCP server (required if running a DHCP server). It is possible to change the default HTTP port

designed to display panel Web device and RTSP ports and port server data. After changing parameter

pres NEXT button.

NVR OPERATING

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

19

II. QR Codes : This menu allows to you to scan a QRcode in the Supelive plus application or enter a

device code to autonat.com site. The service allows you to connect to a device connected to the Internet

network is behind a router equipped with NAT.

NOTE: AAT Holding S.A is not responsible for the operation of the service autonat.com which is

provided by third parties.

III. Add Camera: Allows you to configure the camera and add them to the recorder. Upper window

displays a sophisticated camera by the NVR. To change the addressable cameras, click on the icon

in the column EDIT (This works with cameras NOVUS IP 3000 series).

NVR OPERATING

NVR-6332-H2,NVR-6316-H1,NVR-6308P8-H1,NVR-6304P4-H1

User’s manual (Short) ver.1.0

20

Enter the address in the IP ADDRESS and set the masks in the SUBNET MASK then press the OK

button to save the settings.

Press the button to add a camera to the system.

Added camera will be displayed on the bottom of the menu list. To edit the connection settings of the

camera, press the EDIT column.

If you are having problems connecting to the camera, you must enter the correct user name in the

USER NAME and password in the PASSWORD field and then press the OK button to save the

settings. If the NVR connected to the camera will be on STATUS will be displayed Connected. To

remove a camera from the list, press the in DELETE column.

NVR OPERATING

Strona jest ładowana ...

Novus NVR-6304P4-H1 Instrukcja obsługi

Novus NVR-6304P4-H1 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty