Panasonic SCHC39EC Instrukcja obsługi

Marka: Panasonic

Model: SCHC39EC

Kategoria: Odbiorniki muzyczne Bluetooth

Typ: Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

SC-HC39

until

2014/02/15

POLSKI ENGLISHČESKYESPAÑOL

RQT9944-1R

Operating Instructions

Instrukcja obsługi

Návod k obsluze

Instrucciones de funcionamiento

Compact Stereo System

Kompaktowy zestaw stereo

Kompaktní stereo systém

Sistema estéreo compacto

Thank you for purchasing this product.

Please read these instructions carefully before using

this product, and save this manual for future use.

Dziękujemy za zakupienie tego produktu.

Przed przystąpieniem do eksploatacji opisywanego

produktu należy dokładnie przeczytać niniejsze

zalecenia i zachować instrukcję obsługi do wglądu.

Děkujeme, že jste si zakoupil tento výrobek.

Před použitím tohoto produktu si pečlivě přečtěte tyto

pokyny a celý návod si uložte pro pozdější použití.

Muchísimas gracias por haber adquirido este aparato.

Lea cuidadosamente estas instrucciones antes de usar

este producto, y guarde este manual para usarlo en el

futuro.

Model No. SC-HC39

Included Installation Instructions

(l 2 and 16, 17)

The installation work should be done by a

qualified installation specialist.

Before commencing work, carefully read these

installation instructions and the operating instructions

to ensure that installation is performed correctly.

(Please keep these instructions. You may need them

when maintaining or moving this unit.)

Załączone instrukcje instalacji

(l 20 i 34, 35)

Instalację powinien przeprowadzić wyłącznie

wykwalifikowany specjalista.

Przed rozpoczęciem pracy należy się dokładnie

zapoznać z instrukcją instalacji oraz z instrukcją

obsługi, aby się upewnić, że instalacja została

przeprowadzona prawidłowo.

(Proszę zachować niniejszą instrukcję. Będzie ona

potrzebna podczas serwisowania lub przenoszenia

urządzenia.)

Přiložené pokyny k instalaci (l 38 a 52, 53)

Instalační práce musí být provedeny

kvalifikovaným instalatérským odborníkem.

Před zahájením instalace si pečlivě pročtěte tyto

pokyny k instalaci a návod k obsluze, abyste instalaci

provedli opravdu správně.

(Tyto pokyny si uschovejte. Můžete je potřebovat při

údržbě nebo přesouvání tohoto zařízení.)

Se incluyen instrucciones de instalación

(l 56 y 70, 71)

La instalación debe ser realizada por un

especialista calificado.

Antes de comenzar la instalación, lea

cuidadosamente estas instrucciones de instalación y

el manual de instrucciones para asegurarse de que la

instalación se realice correctamente.

(Conserve estas instrucciones. Puede necesitarlas al

momento de realizar mantenimiento o trasladar esta

unidad)

SC-HC39EC~RQT9944-R.book 1 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

Safety precautions

Unit

≥ To reduce the risk of fire, electric shock or product damage,

– Do not expose this unit to rain, moisture, dripping or

splashing.

– Do not place objects filled with liquids, such as vases, on

this unit.

– Use only the recommended accessories.

– Do not remove covers.

– Do not repair this unit by yourself. Refer servicing to

qualified service personnel.

– Do not let metal objects fall inside this unit.

– Do not place heavy items on this unit.

AC mains lead

≥ To reduce the risk of fire, electric shock or product damage,

– Ensure that the power supply voltage corresponds to the

voltage printed on this unit.

– Insert the mains plug fully into the socket outlet.

– Do not pull, bend, or place heavy items on the lead.

– Do not handle the plug with wet hands.

– Hold onto the mains plug body when disconnecting the

plug.

– Do not use a damaged mains plug or socket outlet.

≥ The mains plug is the disconnecting device.

Install this unit so that the mains plug can be unplugged from

the socket outlet immediately.

Unit

≥ This unit utilizes a laser. Use of controls or adjustments or

performance of procedures other than those specified herein

may result in hazardous radiation exposure.

≥ Do not place sources of naked flames, such as lighted

candles, on this unit.

≥ This unit may receive radio interference caused by mobile

telephones during use. If such interference occurs, please

increase separation between this unit and the mobile

telephone.

≥ This unit is intended for use in moderate climates.

Placement

≥ Place this unit on an even surface.

≥ To reduce the risk of fire, electric shock or product damage,

– Do not install or place this unit in a bookcase, built-in

cabinet or in another confined space. Ensure this unit is

well ventilated.

– Do not obstruct this unit’s ventilation openings with

newspapers, tablecloths, curtains, and similar items.

– Do not expose this unit to direct sunlight, high

temperatures, high humidity, and excessive vibration.

Battery

≥ Danger of explosion if battery is incorrectly replaced.

Replace only with the type recommended by the

manufacturer.

≥ Mishandling of batteries can cause electrolyte leakage and

may cause a fire.

– Remove the battery if you do not intend to use the remote

control for a long period of time. Store in a cool, dark

place.

– Do not heat or expose to flame.

– Do not leave the battery(ies) in a car exposed to direct

sunlight for a long period of time with doors and windows

closed.

– Do not take apart or short circuit.

– Do not recharge alkaline or manganese batteries.

– Do not use batteries if the covering has been peeled off.

≥ When disposing of the batteries, please contact your local

authorities or dealer and ask for the correct method of

disposal.

NORSK

Produkt

≥ For å redusere faren for brann, elektrisk støt eller skade på

apparatet:

– Utsett ikke produktet for regn, fukt, drypping eller sprut.

– Ikke plasser objekter som er fylt med væske, som vaser,

på apparatet.

– Bruk kun anbefalt tilbehør.

– Fjern ikke deksler.

– Reparer ikke denne enheten selv, overlat service til

kvalifisert servicepersonell.

Vekselstrømnett

≥ Nettstøpselet er trukket ut fra denne enheten.

Installer denne enheten slik at nettstøpselet umiddelbart kan

trekkes fra stikkontakten.

Produkt

≥ Dette produktet anvender en laser. Betjening av kontroller

eller justering eller andre inngrep enn de beskrevet i denne

bruksanvisning kan føre til farlig bestråling.

≥ Plasser ikke åpen ild, slik som levende lys, oppå apparatet.

≥ Dette apparatet er beregnet for bruk under moderate

klimaforhold.

Plassering

≥ For å redusere faren for brann, elektrisk støt eller skade på

apparatet:

– Ikke plasser apparatet i en bokhylle, et innebygget

kabinett eller et annet lukket sted. Pass på at produktet er

godt ventilert.

– Apparatets ventilasjonsåpninger må ikke dekkes til med

aviser, duker, gardiner eller lignende.

WARNING

CAUTION

ADVARSEL

FORSIKTIG

Product Identification Marking is located on the bottom of the

unit.

SC-HC39EC~RQT9944-R.book 2 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

ENGLISH

Table of contents

Safety precautions............................................ 2

Accessories....................................................... 3

Control reference guide ................................... 4

Connections ...................................................... 5

Inserting media ................................................. 6

Bluetooth

operations ...................................... 7

Media playback controls .................................. 9

Listening to the radio ..................................... 10

Sound adjustment .......................................... 11

Clock and Timer.............................................. 11

Others .............................................................. 12

Troubleshooting.............................................. 13

Unit and media care........................................ 14

About Bluetooth

............................................ 15

Playable media................................................ 15

Licenses .......................................................... 15

Attaching the unit to a wall (optional)........... 16

Specifications.................................................. 18

Accessories

Check the supplied accessories before using this unit.

About descriptions in these operating

instructions

≥ Pages to be referred to are indicated as “l ±±”.

≥ Unless otherwise indicated, operations are described using

the remote control.

∏ 1 Remote control

(N2QAYB000944)

∏ 1 Battery for remote control

∏ 1 AC mains lead

∏ 1 FM indoor antenna

Wall mounting accessories

∏ 1 Safety holder

∏ 1 Screw

∏ 2 Wall mount

brackets



≥ Do not use AC mains lead with other equipment.

≥ Product numbers provided in these operating instructions are

correct as of January 2014. These may be subject to change.

Disposal of Old Equipment and Batteries

Only for European Union and countries with recycling systems

These symbols on the products, packaging, and/or accompanying documents mean that used

electrical and electronic products and batteries must not be mixed with general household

waste.

For proper treatment, recovery and recycling of old products and used batteries, please take

them to applicable collection points in accordance with your national legislation.

By disposing of them correctly, you will help to save valuable resources and prevent any

potential negative effects on human health and the environment.

For more information about collection and recycling, please contact your local municipality.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national

legislation.

Note for the battery symbol (bottom symbol):

This symbol might be used in combination with a chemical symbol. In this case it complies with

the requirement set by the Directive for the chemical involved.

SC-HC39EC~RQT9944-R.book 3 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

Control reference guide

1 Standby/on switch (Í/I) (Í)

Press to switch the unit from on to standby mode or vice

versa.

In standby mode, the unit is still consuming a small

amount of power.

2 Select the audio source

On this unit:

On the remote control:

[ ]: “BLUETOOTH”

[USB/CD]: “CD” ,. “USB”

3 Basic playback control buttons

4 Adjust the volume (0 (min) to 50 (max))

5 Open or close the sliding door

6 Bluetooth

-pairing button

≥ Press to select “BLUETOOTH” as the audio source.

≥ Press and hold to enter pairing mode (l 7) or

disconnect a Bluetooth

device (l 8).

7 NFC touch area (l 7)

8 Port for USB devices / DC OUT terminal (l 6)

9 AUX IN jack (l 5)

10 Remote control signal sensor

Distance: Within approx. 7 m directly in front

Angle: Approx. 30o left and right

11 Display

12 Sliding door

13 Enter setup menu

14 Change the displayed information

15 Enter sound menu

16 Dim the display panel

Press again to cancel.

17 Mute the sound

Press again to cancel. “MUTE” is also cancelled when the

volume is adjusted or the unit is turned off.

18 Enter playback menu

19 Selection/OK

Top view

“CD” """"-. “BLUETOOTH” """"-. “USB”

^"""--" “AUX” (""-"" “FM” ("-""-}

[RADIO/AUX]: “FM”,. “AUX”

∫ Using the remote control

Insert the battery so the terminals (i and j) match those

in the remote control.

Point it at the remote control signal sensor on this unit.

≥ To avoid interference, please do not put any objects in front of

signal sensor.

(Alkaline or manganese

battery)

SC-HC39EC~RQT9944-R.book 4 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

ENGLISH

Connections



≥ These speakers do not have magnetic shielding. Do not place them near a TV, personal computer or other magnetic devices.

≥ Tape the antenna to a wall or column in a position with the least amount of interference.

≥ If radio reception is poor, use a FM outdoor antenna with a right angle type connector (not supplied).

1 Connect an external music device using an audio

cable (not supplied).

≥ Plug type: ‰3.5 mm stereo

2 Press [RADIO/AUX] to select “AUX” and start

playback on the connected device.

∫ To select the sound input level of the

external device

1 While in AUX mode, press [SOUND] repeatedly to

select “INPUT LEVEL”.

2 Press [3, 4] to select “NORMAL” or “HIGH” and

then press [OK].

≥ The factory default is “NORMAL”.



≥ To improve sound distortion when “HIGH” is selected, select “NORMAL”.

≥ Switch the equalizer off or turn the volume of the external device down to reduce the input signal. High level of input signal will

distort the sound.

≥ For details, refer to the operating instructions of the device.

Connect an external music device

Connect the AC mains lead after all other connections are completed.

This unit consumes a small amount of AC power (l 18) even when turned off.

≥ In the interest of energy conservation, if you will not be using this unit for an extended period of time,

unplug it from the mains socket.

Adhesive tape

(not supplied)

FM indoor antenna

(supplied)

To a mains socket

AC mains lead (supplied)

Connect the antenna.

Audio cable

(not supplied)

SC-HC39EC~RQT9944-R.book 5 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

Inserting media

∫ Charging a device

Charging starts when a device (rated value: 5 V/1.5 A) is connected to the DC OUT terminal of this unit.

1 Turn the unit on.

2 Connect a device.

{. Confirm from the screen of the connected device, etc. to

make sure charging has started.

≥ A cable compatible with your device is required. Use the

cable that comes with your device.

≥ Even if you connect a cable compatible with the DC OUT

terminal of this unit, your device may not be charged. In that

case, use the charger that comes with the device.

≥ Depending on your device, using other chargers may not

work. Check the operating instructions of your device before

use.

≥ Do not connect a device with a rated value higher than 5 V/

1.5 A to this unit.

≥ To check if charging is complete, look at the screen of the

connected device, etc.

≥ Once fully charged, remove the USB cable from the DC OUT

terminal.

≥ To continue charging during standby mode, make sure the

device has started charging before turning the unit to standby

mode.

– When charging a depleted device, do not turn the unit to

standby mode until the device becomes operational.



≥ Make sure that the unit does not fall when inserting or removing media.

≥ When moving this unit, be sure to remove all media and turn this unit to standby mode.

≥ Make sure to tilt the disc so as not to touch the sliding

door.

≥ Do not open the sliding door manually.

The label side

∫ Connecting a USB device

≥ Insert the USB device directly. Do not use any USB extension cable.

≥ Please disconnect the USB device if you finish using.

≥ Before removing the USB device, select a source other than “USB”.

∫ Inserting a CD

USB cable

(not supplied)

To the compatible device

SC-HC39EC~RQT9944-R.book 6 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

ENGLISH

Bluetooth

operations

You can listen to the sound from the Bluetooth

audio device from this unit wirelessly.

≥ Refer to the operating instructions of the Bluetooth

device for details.

≥ If you intend to use an NFC (Near Field Communication)-compatible Bluetooth

device, proceed to “One-Touch

Connection (Connecting by NFC)”.

Preparation

≥ Turn on the Bluetooth

feature of the device and

place the device near this unit.

∫ Pairing with Bluetooth

devices

1 Press [ ] to select “BLUETOOTH”.

{. If “PAIRING” is indicated on the display, go to step 4.

To enter pairing mode*

2 Press [PLAY MENU] to select “PAIRING”.

3 Press [3, 4] to select “OK? YES” and then press

[OK].

To pair with a device

4 Select “SC-HC39” from the Bluetooth

device’s

Bluetooth

menu.

{. The name of the connected device is indicated on the

display for a few seconds.

5 Start playback on the Bluetooth

device.

* You can also enter pairing mode by pressing and holding

[ -PAIRING] on the unit.

∫ Connecting a paired Bluetooth

device

1 Press [ ] to select “BLUETOOTH”.

{. “READY” is indicated on the display.

2 Select “SC-HC39” from the Bluetooth

device’s

Bluetooth

menu.

{. The name of the connected device is indicated on the

display for a few seconds.

3 Start playback on the Bluetooth

device.



≥ If prompted for the passkey, input “0000”.

≥ You can register up to 8 devices with this unit. If a 9th device

is paired, the device that has not been used the longest will

be replaced.

≥ This unit can only be connected to one device at a time.

≥ When “BLUETOOTH” is selected as the source, this unit will

automatically try and connect to the last connected

Bluetooth

device.

For NFC-compatible Bluetooth

devices (Android

devices) only

Simply by touching an NFC (Near Field

Communication)-compatible Bluetooth

device on the

unit, you can complete all preparations, from

registering a Bluetooth

device to establishing a

connection.

Preparation

≥ Turn on the NFC feature of the device.

≥ Android device version lower than 4.1 requires the

installation of the app “Panasonic Music Streaming”

(free of charge).

1 Enter “Panasonic Music Streaming” in the search box

of Google Play

to search, and then select

“Panasonic Music Streaming”.

2 Start the app “Panasonic Music Streaming” on the

device.

– Follow on-screen instructions on your device.

– Always use the latest version of the app.

1 Press [ ] to select “BLUETOOTH”.

2 Touch and hold your device on the NFC touch area

of this unit [ ]. (l 4)

Do not move the Bluetooth

device until it beeps, displays

a message or reacts in some way.

Once the Bluetooth

device has reacted, move the device

away from this unit.

≥ When the registration and connection of the Bluetooth

device is complete, the name of the connected device is

indicated on the display for a few seconds.

≥ The location of the NFC touch area differs depending on

the device. When a connection cannot be established

even if your Bluetooth

device has touched the NFC

touch area of this unit, change the position of the device.

The condition may also improve if you download the

dedicated app “Panasonic Music Streaming” and start it

up.

3 Start playback on the Bluetooth

device.



≥ If you touch another device to this unit, you can update the

Bluetooth

connection. The previously connected device will

be disconnected automatically.

≥ When the connection is established, playback may start

automatically depending on the type of device being used.

≥ The One-Touch Connection may not work properly

depending on the type of device being used.

Connecting via Bluetooth

One-Touch Connection

(Connecting by NFC)

SC-HC39EC~RQT9944-R.book 7 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

You can change the transmission mode to prioritise

transmission quality or sound quality.

Preparation

≥ Press [ ] to select “BLUETOOTH”.

≥ If a Bluetooth

device is already connected,

disconnect it.

1 Press [PLAY MENU] repeatedly to select

“LINK MODE”.

2 Press [3, 4] to select the mode and then press

[OK].

MODE 1: Emphasis on connectivity

MODE 2: Emphasis on sound quality



≥ Select “MODE 1” if the sound is interrupted.

≥ The factory default is “MODE 2”.

If the sound input level from the Bluetooth

device is

too low, change the input level setting.

Preparation

≥ Connect a Bluetooth

device.

1 Press [PLAY MENU] repeatedly to select “INPUT

LEVEL”.

2 Press [3, 4] to select the level and then press

[OK].

“LEVEL 0” ,. “LEVEL i1” ,. “LEVEL i2”

^---------------------------------------------------------J



≥ Select “LEVEL 0” if the sound is distorted.

≥ The factory default is “LEVEL 0”.

1 While a Bluetooth

device is connected:

Press [PLAY MENU] repeatedly to select

“DISCONNECT?”.

2 Press [3, 4] to select “OK? YES” and then press

[OK].



≥ You can also disconnect the Bluetooth

device by pressing

and holding [ -PAIRING] on the unit.

≥ The Bluetooth

device will be disconnected if a different

audio source (e.g., “CD”) is selected.

Bluetooth

transmission mode

Bluetooth

input level

Disconnecting a Bluetooth

device

SC-HC39EC~RQT9944-R.book 8 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

ENGLISH

Media playback controls

The following marks indicate the availability of the

feature.

Preparation

≥ Turn the unit on.

≥ Insert the media or connect the Bluetooth

device.

≥ Press [USB/CD] or [ ] to select the audio source.

∫ To display information

Press [DISPLAY] repeatedly.



≥ To use this unit’s remote control with a Bluetooth

device, the

Bluetooth

device must support AVRCP (Audio Video

Remote Control Profile).

Depending on the status of the device, some controls may

not work.

≥ Maximum number of displayable characters: approx. 30

≥ This unit supports ver. 1.0, 1.1 and 2.3 ID3 tags. Text data

that is not supported will not be displayed or will be shown

differently.

≥ Album and track indication for MP3 files.

Select the playback mode.

1 Press [PLAY MENU] to select “PLAYMODE” or

“REPEAT”.

2 Press [3, 4] to select the setting and then press

[OK].



≥ During random play, you cannot skip to the previous track.

≥ The mode is cancelled when you open the sliding door.

[CD]: CD audio in CD-DA format and a CD that

contains MP3 files (l 15)

[USB]: USB devices containing MP3 files (l 15)

[Bluetooth]: Connected Bluetooth

device

Basic controls

([CD], [USB], [Bluetooth])

Play Press [1/;].

Stop Press [∫].

≥ [USB]: The position is memorised and

“RESUME” is displayed.

Pause Press [1/;].

Press again to restart play.

Skip Press [:/6] or [5/9] to skip

track.

[CD], [USB] Press [3] or [4] to skip

the MP3 album.

Search During play or pause, press and hold

[:/6] or [5/9].

“A _ _ _”: MP3 album number.

“T _ _ _”: MP3 track number.

≥ “ _ ” stands for the album or track number.

“”:

This indication is also used to refer to an album.

“”:

This indication is also used to refer to a track.

Playback modes ([CD], [USB])

PLAYMODE

OFF

PLAYMODE

Cancels the play mode setting.

1-TRACK Only plays the selected track.

≥ “1”, “ ” is displayed.

(Skip to the desired track.)

1-ALBUM Only plays the selected MP3 album.

≥ “1”, “ ” is displayed.

RANDOM Plays the contents randomly.

≥ “RND” is displayed.

1-ALBUM

RANDOM

Plays the tracks in the selected

MP3 album randomly.

≥ Press [3] or [4] to select the MP3

album.

≥ “1”, “ ”, “RND” is displayed.

REPEAT

ON REPEAT Turns on repeat mode.

≥ “`” is displayed.

OFF

REPEAT

Turns off repeat mode.

SC-HC39EC~RQT9944-R.book 9 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

Listening to the radio

You can preset up to 30 channels.

Preparation

≥ Make sure that the antenna is connected. (l 5)

≥ Turn the unit on.

≥ Press [RADIO/AUX] to select “FM”.



≥ A station previously stored is overwritten when another

station is stored in the same channel preset.

1 Press [PLAY MENU] to select “A.PRESET”.

2 Press [3, 4] to select “LOWEST” or “CURRENT”

and then press [OK].

LOWEST:

To begin auto preset with the lowest frequency

(FM 87.50).

CURRENT:

To begin auto preset with the current frequency.*

{. The tuner starts to preset all the stations it can receive

into the channels in ascending order.

* To change the frequency, refer to “Manual tuning and

presetting”.

1 Press [PLAY MENU] repeatedly to select

“TUNEMODE”.

2 Press [3, 4] to select “PRESET” and then press

[OK].

3 Press [:/6] or [5/9] to select the

channel.

∫ Manual tuning and presetting

Select a radio broadcast.

1 Press [PLAY MENU] repeatedly to select

“TUNEMODE”.

2 Press [3, 4] to select “MANUAL” and then press

[OK].

3 Press [:/6] or [5/9] to tune to the

required station.

≥ To start automatic tuning, press and hold [:/6] or

[5/9] until the frequency starts scrolling. Tuning

stops when a station is found.

To preset the channel

4 While listening to the radio broadcast, press [OK].

5 Press [3, 4] to select the channel and then press

[OK].

∫ To improve FM sound quality

1 While receiving FM broadcasts, press

[PLAY MENU] repeatedly to select “FM MODE”.

2 Press [3, 4] to select “MONO” and then press

[OK].

≥ This setting can be preset and memorised. To do so,

continue to step 4 of “Manual tuning and presetting”.



≥ Select “STEREO” in step 2 to return to stereo broadcasts.

≥ “MONO” is cancelled if the frequency is changed.

∫ To display the current FM signal status

While receiving FM signal, press [PLAY MENU]

repeatedly to display “FM STATUS” and then press

[OK].

∫ To display RDS text data

Press [DISPLAY] to display the text data.

≥ Each time you press the button:



≥ “STEREO” is displayed when this unit tunes to a stereo

broadcast.

≥ The unit can display the text data transmitted by the radio

data system (RDS) available in some areas. (RDS displays

may not be available if reception is poor.)

Presetting stations automatically

Listening to a preset channel

“FM ST”: The FM signal is tuned and in stereo.

“FM”: There is no tuned signal or the FM signal

is in monaural.

“FM MONO”: “MONO” is selected in step 2 of “To

improve FM sound quality” (l above).

“PS”: Programme service

“PTY”: Programme type

“FREQ”: Frequency display

SC-HC39EC~RQT9944-R.book 10 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

ENGLISH

Sound adjustment

The following sound effects can be added to the audio

output.

1 Press [SOUND] repeatedly to select the effect.

2 Press [3, 4] to select the setting and then press

[OK].

≥ You may experience a reduction in sound quality when these

effects are used with some sources. If this occurs, turn the

sound effects off.

≥ When “AUX” is selected as the source, you can select

“INPUT LEVEL” to adjust the sound input level of the

external device. (l 5)

Clock and Timer

This is a 24-hour clock.

1 Press [SETUP] repeatedly to select “CLOCK”.

2 Press [3, 4] to set the time and then press [OK].



≥ To display the clock, press [SETUP] repeatedly to select

“CLOCK” and then press [OK] once. The time is displayed for

10 seconds.

(During standby, press [DISPLAY] once.)

≥ The clock is reset when there is a power failure or when the

AC mains lead is removed.

≥ Reset the clock regularly to maintain accuracy.

You can set the timer so this unit turns on at a certain

time every day.

Preparation

Set the clock.

∫ Setting the timer

1 Press [SETUP] repeatedly to select “TIMER ADJ”.

2 Press [3, 4] to set the starting time (“ON TIME”)

and then press [OK].

3 Press [3, 4] to set the finishing time

(“OFF TIME”) and then press [OK].

4 Press [3, 4] to select the music source*

and then

press [OK].

∫ Turning the timer on

1 Prepare the selected music source and set the

desired volume.

2 Press [SETUP] repeatedly to select “TIMER SET”.

3 Press [3, 4] to select “SET” and then press [OK].

≥ “F” is displayed.

≥ To turn the timer off, select “OFF”.

4 Press [Í] to turn the unit to standby mode.



≥ To display the timer settings, press [SETUP] repeatedly to

select “TIMER ADJ” and then press [OK] once.

The music source and volume will also be displayed if the

timer is turned on.

≥ During standby, if the timer is turned on, press [DISPLAY]

twice to display the settings.

≥ This unit can be used as normal after the timer is set,

however:

– Turn the unit to standby mode before the timer start time.

– Even if the audio source or the volume is changed, the

timer will still use the audio source and volume that was

set when the timer was turned on.

The sleep timer can turn the unit off after a set time.

1 Press [SETUP] to select “SLEEP”.

2 Press [3, 4] to set the time (in minutes) and then

press [OK].

“SLEEP 30” ,. “SLEEP 60” ,. “SLEEP 90” ,. “SLEEP 120”

^------------------. “OFF” (Cancel) (------------------J



≥ The remaining time is indicated on the unit’s display except

when other operations are performed.

≥ The play timer and sleep timer can be used together. The

sleep timer is always the main timer on the unit.

“PRESET EQ”

(Preset Equalizer)

“HEAVY” (heavy), “SOFT” (soft),

“CLEAR” (clear), “VOCAL”

(vocal) or “FLAT” (flat/off).

≥ The factory default is “HEAVY”.

“BASS” (Bass) or

“TREBLE” (Treble)

Adjust the level (j4 to i4).

“D.BASS”

(Dynamic Bass)

“ON D.BASS” or “OFF D.BASS”.

≥ The factory default is

“ON D.BASS”.

“SURROUND”

(Surround)

“ON SURROUND” or

“OFF SURROUND”.

≥ The factory default is

“OFF SURROUND”.

Setting the clock

Play timer

* “CD”, “USB”, “FM” and “AUX” can be set as the music

source.

Sleep timer

SC-HC39EC~RQT9944-R.book 11 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

Others

As a factory default, this unit will turn to standby mode

automatically if there is no sound and it is not being

used for approximately 20 minutes.

To cancel this function

1 Press [SETUP] repeatedly to select “AUTO OFF”.

2 Press [3, 4] to select “OFF” and then press [OK].



≥ To turn the function on, select “ON” in step 2.

≥ This setting cannot be selected when “FM” is the source.

≥ When connected to a Bluetooth

device, the function does

not work.

When “SC-HC39” is selected from a paired Bluetooth

device’s Bluetooth

menu, this unit will turn on

automatically from standby mode and establish a

Bluetooth

connection.

1 Press [SETUP] repeatedly to select “BLUETOOTH

STANDBY”.

2 Press [3, 4] to select “ON” and then press [OK].



≥ To turn the function off, select “OFF” in step 2.

When other Panasonic equipment responds to the

supplied remote control, change the remote control

code.

1 Press [USB/CD] to select “CD”.

2 While pressing and holding [SELECTOR] on the

unit, press and hold [USB/CD] on the remote

control until the unit’s display shows “REMOTE 2”.

3 Press and hold [OK] and [USB/CD] on the remote

control for at least 4 seconds.



≥ To change the mode back to “REMOTE 1”, press [USB/CD]

to select “CD” and then repeat the step 2 and 3 but replace

[USB/CD] with [ ].

Occasionally, Panasonic may release updated

software for this unit that may add or improve the way

a feature operates. These updates are available free of

charge.

For more details, refer to the following website.

http://panasonic.jp/support/global/cs/

(This site is in English only.)

∫ Checking the software version

The version of the installed software is displayed.

Press [SETUP] repeatedly to select “SW VER.” and

then press [OK].

≥ Press [OK] to exit.

Auto off function

Bluetooth

standby

Changing the unit and remote

control code

Software update

SC-HC39EC~RQT9944-R.book 12 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

ENGLISH

Troubleshooting

Before requesting service, make the following checks. If

you are uncertain about some of the check points, or if the

solutions indicated in the following guide does not resolve

the issue, then consult your dealer for instructions.

Humming heard during playback.

≥ If an AC mains lead or fluorescent lights are near the cords, then

keep other appliances and cords away from the cables.

The unit does not work.

≥ One of the unit’s safety devices may have been activated.

Reset the unit as follows:

1 Press [Í/I] on the unit to switch the unit to standby.

≥ If the unit does not switch to standby, press [Í/I] on the unit

for approximately 10 seconds. The unit is forcibly switched

to standby. Alternatively, disconnect the AC mains lead, wait

for at least 3 minutes, then reconnect it.

2 Press [Í/I] on the unit to switch it on. If the unit still cannot be

operated, consult the dealer.

MP3 cannot be read.

≥ You may not be able to play MP3 if you have copied a

multi-session disc that has no data between sessions.

≥

When creating a multi-session disc, it is necessary to close the session.

≥ The amount of data on the disc is too small. Set the amount of

data to above 5 MB.

Charging does not start during standby mode.

≥ Turn the unit on. Check the charging has started, and then turn

the unit to standby mode. (l 6)

Noise is heard.

≥ When a device is connected to both the AUX IN jack and the DC

OUT terminal, noise may be generated depending on the device.

In this case, remove the USB cable from the DC OUT terminal.

The remote control does not work properly.

≥ The battery is depleted or inserted incorrectly. (l 4)

Incorrect display or play does not start.

≥ Make sure that the disc is compatible with this unit. (l 15)

≥

There is moisture on the lens. Wait for about an hour and then try again.

No response when [1/;] is pressed.

≥ Disconnect the USB device and then reconnect it. Alternatively,

turn the unit off and on again.

The USB drive or its contents cannot be read.

≥ The USB drive format or its contents is/are not compatible with the

unit (l 15).

≥ The USB host function of this product may not work with some

USB devices.

Slow operation of the USB flash drive.

≥ Large file size or high memory USB flash drive takes longer time

to read.

The elapsed time displayed is different from the

actual play time.

≥ Copy the data to another USB device or backup the data and

reformat the USB device.

Static or noisy reception is heard while listening to

a radio broadcast.

≥ Confirm the antenna is properly connected. (l 5)

≥ Adjust the position of the antenna.

≥ Try to keep a certain amount of distance between the antenna and

AC mains lead.

≥ Try using an outdoor antenna if there are buildings or mountains

nearby. (l 5)

≥ Turn the TV or other audio players off or separate it from this unit.

≥ Keep this unit away from mobile phones if there is interference.

Pairing cannot be completed.

≥ Check the Bluetooth

device condition.

The device cannot be connected.

≥ The pairing of the device was unsuccessful or the registration has

been replaced. Try re-pairing the device. (l 7)

≥ This unit might be connected to a different device. Disconnect the

other device and try re-pairing the device. (l 7)

The device is connected, but audio cannot be

heard through this unit.

≥ For some built-in Bluetooth

devices, you have to set the audio

output to “SC-HC39” manually. Read the operating instructions for

the device for details.

The sound is interrupted.

≥ The device is out of the 10 m communication range. Place the

Bluetooth

device closer to this unit.

≥ Remove any interference between this unit and the device.

≥ Other devices that use the 2.4 GHz frequency band, such as

wireless routers, microwaves, cordless phones, etc. are

interfering. Place the Bluetooth

device closer to this unit and

distance it from the other devices.

≥ Select “MODE 1” for stable communication. (l 8)

The One-Touch Connection (NFC feature) is not

working.

≥ Make sure the unit and the NFC feature of the device are turned

on. (l 7)

To return all settings to the factory defaults

When the following situations occur, reset the

memory:

≥ There is no response when buttons are pressed.

≥ You want to clear and reset the memory contents.

1 Disconnect the AC mains lead. (Wait for at least

3 minutes before proceeding to step 2.)

2 While pressing and holding down [Í/I] on the

unit, reconnect the AC mains lead.

≥ Keep holding down [Í/I] until “---------” appears on the

display.

3 Release [Í/I].



≥ All the settings are returned to the factory defaults. You will

need to reset the memory items.

General

Remote control

Disc

USB

Radio

Bluetooth

SC-HC39EC~RQT9944-R.book 13 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

The following messages or service numbers may

appear on the unit’s display.

“--:--”

≥ You plugged the AC mains lead in for the first time or there was a

power failure recently. Set the time (l 11).

“ADJUST CLOCK”

≥ Clock is not set. Adjust the clock accordingly.

“ADJUST TIMER”

≥ Play timer is not set. Adjust the play timer accordingly.

“AUTO OFF”

≥ The unit has been left unused for about 20 minutes and will shut

down within a minute. Press any button to cancel it.

“ERROR”

≥ Incorrect operation is performed. Read the instructions and try

again.

“F” (“  ” stands for a number.)

≥ There is a problem with this unit.

Write down the displayed number, disconnect the AC mains lead

and consult your dealer.

“ILLEGAL OPEN”

≥ Sliding door is in the wrong position. Turn the unit off and on

again. If this display appears again, consult the dealer.

“NODEVICE”

≥ The USB device is not inserted correctly. Read the instructions

and try again (l 6).

“NO DISC”

≥ Insert the disc to be played (l 6).

“NO PLAY”

≥ A CD that is not in CD-DA or MP3 format is inserted. It cannot be

played.

≥ Examine the content. You can only play supported format. (l 15)

≥ The files in the USB device can be corrupted. Format the USB

device and try again.

≥ The unit may have a problem. Turn the unit off and then on again.

“PLAYERROR”

≥ You played an unsupported MP3 file. The system will skip that

track and play the next one.

“READING”

≥ The unit is checking the CD/USB information. After this display

has disappeared, start operating.

“REMOTE ” (“  ” stands for a number.)

≥ The remote control and this unit are using different codes. Change

the code on the remote control.

– When “REMOTE 1” is displayed, press and hold [OK] and [ ]

for at least 4 seconds.

– When “REMOTE 2” is displayed, press and hold [OK] and

[USB/CD] for at least 4 seconds.

“USB OVER CURRENT ERROR”

≥ The USB device is drawing too much power. Select a source other

than “USB”, remove the USB and turn the unit off.

“VBR”

≥ The system cannot show the remaining play time for variable bit

rate (VBR) tracks.

Unit and media care

Pull out the AC mains lead from the outlet before

maintenance.

∫ Clean this unit with a soft, dry cloth

≥ When dirt is heavy, wring a wet cloth tightly to wipe the dirt,

and then wipe it with a dry cloth.

≥ When cleaning the speaker covers, use a fine cloth.

Do not use tissues or other materials that can fall apart.

Small pieces may get stuck inside the speaker cover.

≥ Never use alcohol, paint thinner or benzine to clean this unit.

≥ Before using chemically treated cloth, carefully read the

cloth’s instructions.

∫ Maintenance of the lens

≥ Clean the lens regularly to prevent malfunctions. Use a dust

blower to remove dust and a cotton swab if it is extremely

dirty.

≥ You cannot use a CD type lens cleaner.

≥ Do not leave the sliding door open for prolonged periods of

time. This will cause the lens to get dirty.

≥ Be careful not to touch the lens with your fingers.

∫ Clean discs

Wipe with a damp cloth and then wipe dry.

∫ Disc handling precautions

≥ Handle discs by the edges to avoid inadvertent scratches or

fingerprints on the disc.

≥ Do not attach labels or stickers to discs.

≥ Do not use record cleaning sprays, benzine, thinner, static

electricity prevention liquids or any other solvent.

≥ Do not use the following discs:

– Discs with exposed adhesive from removed stickers or

labels (rented discs etc.).

– Discs that are badly warped or cracked.

– Irregularly shaped discs, such as heart shapes.

∫ To dispose or transfer this unit

The unit may keep the user settings information in the

unit. If you discard this unit either by disposal or

transfer, then follow the procedure to return all the

settings to the factory defaults to delete the user

settings.

(l 13, “To return all settings to the factory defaults”)

≥ The operation history may be recorded in the

memory of this unit.

Messages

DO DO NOT

Lens

SC-HC39EC~RQT9944-R.book 14 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

ENGLISH

About Bluetooth

∫ Frequency band used

≥ This system uses the 2.4 GHz frequency band.

∫ Certification of this device

≥ This system conforms to frequency restrictions and

has received certification based on frequency laws.

Thus, a wireless permit is not necessary.

≥ The actions below are punishable by law in some

countries:

– Taking apart or modifying the system.

– Removing specification indications.

∫ Restrictions of use

≥ Wireless transmission and/or usage with all

Bluetooth

equipped devices is not guaranteed.

≥ All devices must conform to standards set by

Bluetooth SIG, Inc.

≥ Depending on the specifications and settings of a

device, it can fail to connect or some operations can

be different.

≥ This system supports Bluetooth

security features.

But depending on the operating environment and/or

settings, this security is possibly not sufficient.

Transmit data wirelessly to this system with caution.

≥ This system cannot transmit data to a Bluetooth

device.

∫ Range of use

≥ Use this device at a maximum range of 10 m. The

range can decrease depending on the environment,

obstacles or interference.

∫ Interference from other devices

≥ This system may not function properly and troubles

such as noise and sound jumps may arise due to

radio wave interference if this system is located too

close to other Bluetooth

devices or the devices that

use the 2.4 GHz band.

≥ This system may not function properly if radio waves

from a nearby broadcasting station, etc. is too

strong.

∫ Intended usage

≥ This system is for normal, general use only.

≥ Do not use this system near an equipment or in an

environment that is sensitive to radio frequency

interference (example: airports, hospitals,

laboratories, etc).

Playable media

≥ A disc with the CD Logo.

≥ This unit can play back discs that conform to the CD-DA

format.

≥ The unit may not be able to play some discs due to the

condition of the recording.

≥ Before playback, finalise the disc on the device it was

recorded on.

≥ This unit does not guarantee connection with all USB

devices.

≥ FAT12, FAT16 and FAT32 file systems are supported.

≥ This unit supports USB 2.0 full speed.

≥ This unit can support USB devices of up to 32 GB.

≥ Supported format: Files with the extension “.mp3” or “.MP3”.

≥ Compatible compression rate: Between 16 kbps and

320 kbps (stereo).

≥ Depending on how you create the MP3 files, they may not

play in the order you numbered them or may not play at all.

CD-R/RW

≥ Maximum number of tracks and albums: 999 tracks and 254

albums (Excluding Root folder).

≥ Disc formats: ISO9660 level 1 and level 2 (except for

extended formats).

≥ If the disc includes both MP3 and normal audio data

(CD-DA), the unit plays the type recorded in the inner part of

the disc.

≥ This unit cannot play files recorded using packet write.

USB device

≥ Maximum number of tracks and albums: 8000 tracks and 799

albums (Excluding Root folder).

≥ Only one memory card will be selected when connecting a

multiport USB card reader, typically the first memory card

inserted.

Licenses

Panasonic bears no responsibility for data and/or

information that is compromised during a

wireless transmission.

Compatible CD

Compatible USB devices

Compatible MP3 files

The Bluetooth

word mark and logos are owned by the

Bluetooth SIG, Inc. and any use of such marks by Panasonic

Corporation is under license.

Other trademarks and trade names are those of their respective

owners.

Google Play and Android are trademarks of Google Inc.

MPEG Layer-3 audio coding technology licensed from

Fraunhofer IIS and Thomson.

SC-HC39EC~RQT9944-R.book 15 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

Attaching the unit to a wall

(optional)

This unit can be wall mounted using the supplied wall

mount brackets, etc. Make sure that the wall and the

screws used for securing to the wall are capable of

supporting at least 33 kg. The screws and other items

are not supplied as the type and size will vary with

each installation.

≥ Refer to step 5 of “Wall mount instructions” for details

about the required screws.

≥ As an additional protective measure, attach the unit

to the wall with the fall prevention cord.

∫ Supplied accessories

≥ 1 Safety holder

≥ 1 Screw

≥ 2 Wall mount brackets

∫ Additionally required accessories

(commercially available)

≥ 4 Wall mount bracket fixing screws

≥ 1 Safety holder fixing screw

≥ 1 Fall prevention cord*

≥ 1 Screw eye

* Use a cord that is capable of supporting over 33 kg

(with a diameter of about 1.5 mm).

1 Detach the stand from the unit.

≥ Unscrew the fixing screw at the bottom of the unit.

≥ Gently pull the stand off the unit as illustrated.

≥ Keep the removed screw and the stand in a safe place.

2 Fix the safety holder onto the unit with the screw

(supplied).

≥ Screw tightening torque: 50 N0cm to 70 N0cm.

3 Attach the fall prevention cord (not supplied) to this

unit.

Installation accessories

≥ Keep the safety holder out of reach of children to

prevent swallowing.

≥ Keep the screws out of reach of children to prevent

swallowing.

≥ Keep the wall mount brackets out of reach of children

to prevent swallowing.

Safety precautions

Professional installation is required.

The installation should never be done by any

other than a qualified installation specialist.

PANASONIC DISCLAIMS ANY PROPERTY

DAMAGE AND/OR SERIOUS INJURY,

INCLUDING DEATH RESULTING FROM

IMPROPER INSTALLATION OR INCORRECT

HANDLING.

WARNING:

To prevent injury, this apparatus must be securely

attached to the wall in accordance with the

installation instructions.

Wall mount instructions

Before installation, turn the unit off and disconnect the

AC mains lead from the mains socket.

Stand

Fixing screw

Soft blanket or cloth

Screw

(supplied)

Cord

(not supplied)

SC-HC39EC~RQT9944-R.book 16 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

ENGLISH

4 Measure and mark the position of both sides of the

wall mount brackets.

≥ Use figures below to identify the screwing positions.

The position to attach the wall mount brackets

Space required

5 Attach the wall mount bracket to both sides of the

wall with two screws (not supplied).

≥ Use a level to ensure both wall mount brackets are

level.

6 Hook the unit securely onto the wall mount

brackets with both hands.

≥ After hanging the unit, release your hands carefully to

confirm the unit sits securely on the wall mount

brackets.

7 Drive the safety holder fixing screw (not supplied)

to secure the safety holder onto the wall.

≥ Refer to step 5 for requirements before screwing.

8 Attach the fall prevention cord (not supplied) to the

wall.

≥ Make sure that the slack of the cord is minimal.

204 mm

13 mm

500 mm

75 mm

142 mm

154 mm

100 mm

142

300 mm

100 mm

At least 30 mm

‰7.5 mm to

‰9.4 mm

‰4 mm

Wall mount bracket

≥ Connect the antenna and the AC mains lead to the unit

before hanging the unit onto the wall. (l 5)

Wall

Safety holder fixing screw

(not supplied)

Safety holder

Fix to the wall

Cord (not supplied)

Screw eye (not supplied)

Wall

SC-HC39EC~RQT9944-R.book 17 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

Specifications



≥ Specifications are subject to change without notice.

≥ Mass and dimensions are approximate.

≥ Total harmonic distortion is measured by a digital spectrum

analyzer.

*1: “BLUETOOTH STANDBY” is “OFF”.

*2: No device is connected to the USB port before turning to

standby mode.

*3: MPEG-1 Layer 3, MPEG-2 Layer 3

∫ GENERAL

Power consumption 26 W

Power consumption in standby mode*

1, 2

Approx. 0.2 W

(When “BLUETOOTH STANDBY” is “ON”)*

Approx. 0.3 W

Power supply

AC 220 V to 240 V, 50 Hz

Dimensions (WkHkD)

500 mmk205 mmk92 mm

Mass Approx. 2.5 kg

Operating temperature range

0 oC to r40 oC

Operating humidity range

35 % to 80 % RH (no condensation)

∫ AMPLIFIER SECTION

Output power

RMS Output Power Stereo mode

Front Ch (both ch driven)

20 W per channel (8 ≠), 1 kHz, 10 % THD

Total RMS Stereo mode power

40 W

∫ TUNER SECTION

Preset Memory FM 30 stations

Frequency Modulation (FM)

Frequency range

87.50 MHz to 108.00 MHz (50 kHz step)

Antenna terminals

75 ≠ (unbalanced)

∫ DISC SECTION

Disc played (8 cm or 12 cm)

CD, CD-R/RW (CD-DA, MP3*

)

Pick up

Wavelength 790 nm (CD)

[NORSK]

Bølgelengde 790 nm (CD)

Laserstyrke Ingen farlig stråling sendes ut

(med sikkerhets-beskyttelse)

∫ SPEAKER SYSTEM SECTION

Speaker unit(s)

Full range

6.5 cm Cone typek1 per channel

Passive Radiator

8cmk2 per channel

Impedance 8 ≠

∫ TERMINAL SECTION

USB Port

DC OUT 5V 1.5A

USB Standard

USB 2.0 full speed

Media file format support

MP3 (¢.mp3)

USB device file system

FAT12, FAT16, FAT32

AUX IN

Stereo, 3.5 mm jack

∫ BLUETOOTH SECTION

Version Bluetooth

Ver.2.1+EDR

Class Class 2

Supported Profiles

A2DP, AVRCP

Operating Frequency

2.4 GHz band FH-SS

Operation Distance

10 m Line of sight

SC-HC39EC~RQT9944-R.book 18 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

ENGLISH

SC-HC39EC~RQT9944-R.book 19 ページ２０１４年４月２日　水曜日　午後３時２９分

RQT9944

Zasady bezpieczeństwa

Urządzenie

≥ Aby ograniczyć niebezpieczeństwo pożaru, porażenia

prądem lub uszkodzenia urządzenia,

– Nie należy wystawiać urządzenia na działanie deszczu,

wilgoci, kapanie lub zachlapanie.

– Na urządzeniu nie należy ustawiać żadnych naczyń

zawierających płyny, takich jak wazony.

–Należy korzystać wyłącznie z zalecanych akcesoriów.

– Nie należy demontować obudowy urządzenia.

– Nie należy podejmować prób samodzielnej naprawy.

Naprawę urządzenia należy zlecić wykwalifikowanym

pracownikom serwisu.

–Należy uważać, aby do wnętrza urządzenia nie dostały

się metalowe przedmioty.

– Na urządzeniu nie wolno umieszczać żadnych ciężkich

przedmiotów.

Przewód zasilania

≥ Aby ograniczyć niebezpieczeństwo pożaru, porażenia

prądem lub uszkodzenia urządzenia,

–Należy się upewnić, że napięcie źródła zasilania

odpowiada napięciu podanemu na urządzeniu.

–Dokładnie podłączyć wtyczkę przewodu zasilającego do

gniazda ściennego.

– Nie wolno ciągnąć za przewód, zginać go ani kłaść na nim

ciężkich przedmiotów.

– Nie wolno dotykać wtyczki mokrymi rękami.

– Przy odłączaniu przewodu należy chwycić za wtyczkę.

– Nie wolno podłączać urządzenia do uszkodzonego

gniazda ściennego oraz gdy wtyczka przewodu

zasilającego jest uszkodzona.

≥ Wtyczka zasilania umożliwia odłączenie urządzenia.

Zainstaluj to urządzenie w taki sposób, aby mo

żliwe było

natychmiastowe odłączenie wtyczki zasilania od gniazda

zasilania.

Urządzenie

≥ W tym urządzeniu znajduje się laser. Wykonywanie regulacji

innych niż opisane lub postępowanie w sposób

nieprzewidziany w instrukcji obsługi grozi niebezpiecznym

naświetleniem promieniami lasera.

≥ Nie należy umieszczać na urządzeniu źródeł otwartego

ognia, takich jak zapalone świece.

≥ To u rządzenie może odbierać zakłócenia wywołane użyciem

telefonu komórkowego. Jeżeli takie zakłócenia wystąpią,

wskazane jest zwiększenie odległości pomiędzy

urządzeniem a telefonem komórkowym.

≥ Urządzenie jest przeznaczone do używania w klimacie

umiarkowanym.

Wybór miejsca

≥ Urządzenie należy ustawić na równej powierzchni.

≥ Aby ograniczyć niebezpieczeństwo pożaru, porażenia

prądem lub uszkodzenia urządzenia,

– Niniejszego urządzenia nie należy instalować lub

umieszczać w szafce na książki, zabudowanej szafce lub

innej ograniczonej przestrzeni, w celu zapewnienia dobrej

wentylacji.

– Nie należy zasłaniać otworów wentylacyjnych urządzenia

gazetami, obrusami, zasłonami i podobnymi

przedmiotami.

–Urządzenie należy chronić przed bezpośrednim

działaniem promieni słonecznych, wysoką temperaturą,

wysoką wilgotnością oraz nadmiernymi drganiami.

Bateria

≥ Istnieje niebezpieczeństwo wybuchu w przypadku, gdy

baterie zostaną nieprawidłowo włożone. Baterie należy

wymieniać wyłącznie na baterie typu zalecanego przez

producenta.

≥ Nieprawidłowe obchodzenie się z bateriami może prowadzić

do wycieku elektrolitu i może być także przyczyną pożaru.

– Baterię należy wyjąć, jeżeli pilot nie będzie używany przez

dłuższy czas. Należy ją przechowywać w chłodnym,

ciemnym miejscu.

– Nie ogrzewaj i nie wrzucaj do ognia.

– Nie należy pozostawiać baterii przez dłuższy czas w

samochodzie z zamkniętymi drzwiami i oknami

wystawionym na bezpośrednie działanie promieni

słonecznych.

– Nie demontuj i nie powoduj zwarcia.

– Baterii alkalicznych lub manganowych nie należy ładować

ponownie.

– Nie używaj baterii, z których usuni

ęta została osłona.

≥ W przypadku utylizacji baterii, należy się skontaktować z

lokalnymi władzami lub ze sprzedawcą celem uzyskania

informacji o prawidłowym sposobie postępowania.

OSTRZEËENIE

UWAGA

Oznaczenia identyfikacyjne produktu znajdują się na

spodzie urządzenia.

Deklaracja zgodności

Niniejszym “Panasonic Corporation” deklaruje, że ten

produkt jest zgodny z istotnymi wymaganiami i innymi

odnośnymi postanowieniami dyrektywy 1999/5/WE.

Klienci mogą pobrać oryginalną deklarację zgodności

naszych produktów z serwera deklaracji zgodności:

http://www.doc.panasonic.de

Kontakt się z autoryzowanym przedstawicielem: Panasonic

Marketing Europe GmbH,

Panasonic Testing Centre, Winsbergring 15, 22525

Hamburg, Niemcy

Ten produkt jest przeznaczony dla użytkownika ogólnego.

(Kategoria 3)

SC-HC39EC~RQT9944-R.book 20 ページ２０１４年４月２日　水曜日　午後３時２９分

Strona jest ładowana ...

Panasonic SCHC39EC Instrukcja obsługi

Marka: Panasonic

Model: SCHC39EC

Kategoria: Odbiorniki muzyczne Bluetooth

Typ: Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

SC-HC39

ściągnij PDF

raport

w innych językach

español: Panasonic SCHC39EC El manual del propietario
slovenčina: Panasonic SCHC39EC Návod na obsluhu
English: Panasonic SCHC39EC Owner's manual

Panasonic SCHC39EC Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Panasonic SCHC39EC Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty