Panasonic SC-HC39 Instrukcja obsługi

Kategoria
Odbiorniki muzyczne Bluetooth
Typ
Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

until
2014/02/15
POLSKI ENGLISHČESKYESPAÑOL
RQT9944-1R
EC
Operating Instructions
Instrukcja obsługi
Návod k obsluze
Instrucciones de funcionamiento
Compact Stereo System
Kompaktowy zestaw stereo
Kompaktní stereo systém
Sistema estéreo compacto
Thank you for purchasing this product.
Please read these instructions carefully before using
this product, and save this manual for future use.
Dziękujemy za zakupienie tego produktu.
Przed przystąpieniem do eksploatacji opisywanego
produktu należy dokładnie przeczytać niniejsze
zalecenia i zachować instrukcję obsługi do wglądu.
Děkujeme, že jste si zakoupil tento výrobek.
Před použitím tohoto produktu si pečlivě přečtěte tyto
pokyny a celý návod si uložte pro pozdější použití.
Muchísimas gracias por haber adquirido este aparato.
Lea cuidadosamente estas instrucciones antes de usar
este producto, y guarde este manual para usarlo en el
futuro.
Model No. SC-HC39
Included Installation Instructions
(l 2 and 16, 17)
The installation work should be done by a
qualified installation specialist.
Before commencing work, carefully read these
installation instructions and the operating instructions
to ensure that installation is performed correctly.
(Please keep these instructions. You may need them
when maintaining or moving this unit.)
Załączone instrukcje instalacji
(l 20 i 34, 35)
Instalację powinien przeprowadzić wyłącznie
wykwalifikowany specjalista.
Przed rozpoczęciem pracy należy się dokładnie
zapoznać z instrukcją instalacji oraz z instrukcją
obsługi, aby się upewnić, że instalacja została
przeprowadzona prawidłowo.
(Proszę zachować niniejszą instrukcję. Będzie ona
potrzebna podczas serwisowania lub przenoszenia
urządzenia.)
Přiložené pokyny k instalaci (l 38 a 52, 53)
Instalační práce musí být provedeny
kvalifikovaným instalatérským odborníkem.
Před zahájením instalace si pečlivě pročtěte tyto
pokyny k instalaci a návod k obsluze, abyste instalaci
provedli opravdu správně.
(Tyto pokyny si uschovejte. Můžete je potřebovat při
údržbě nebo přesouvání tohoto zařízení.)
Se incluyen instrucciones de instalación
(l 56 y 70, 71)
La instalación debe ser realizada por un
especialista calificado.
Antes de comenzar la instalación, lea
cuidadosamente estas instrucciones de instalación y
el manual de instrucciones para asegurarse de que la
instalación se realice correctamente.
(Conserve estas instrucciones. Puede necesitarlas al
momento de realizar mantenimiento o trasladar esta
unidad)
SC-HC39EC~RQT9944-R.book 1 ページ 2014年4月2日 水曜日 午後3時29分
2
RQT9944
Safety precautions
Unit
To reduce the risk of fire, electric shock or product damage,
Do not expose this unit to rain, moisture, dripping or
splashing.
Do not place objects filled with liquids, such as vases, on
this unit.
Use only the recommended accessories.
Do not remove covers.
Do not repair this unit by yourself. Refer servicing to
qualified service personnel.
Do not let metal objects fall inside this unit.
Do not place heavy items on this unit.
AC mains lead
To reduce the risk of fire, electric shock or product damage,
Ensure that the power supply voltage corresponds to the
voltage printed on this unit.
Insert the mains plug fully into the socket outlet.
Do not pull, bend, or place heavy items on the lead.
Do not handle the plug with wet hands.
Hold onto the mains plug body when disconnecting the
plug.
Do not use a damaged mains plug or socket outlet.
The mains plug is the disconnecting device.
Install this unit so that the mains plug can be unplugged from
the socket outlet immediately.
Unit
This unit utilizes a laser. Use of controls or adjustments or
performance of procedures other than those specified herein
may result in hazardous radiation exposure.
Do not place sources of naked flames, such as lighted
candles, on this unit.
This unit may receive radio interference caused by mobile
telephones during use. If such interference occurs, please
increase separation between this unit and the mobile
telephone.
This unit is intended for use in moderate climates.
Placement
Place this unit on an even surface.
To reduce the risk of fire, electric shock or product damage,
Do not install or place this unit in a bookcase, built-in
cabinet or in another confined space. Ensure this unit is
well ventilated.
Do not obstruct this unit’s ventilation openings with
newspapers, tablecloths, curtains, and similar items.
Do not expose this unit to direct sunlight, high
temperatures, high humidity, and excessive vibration.
Battery
Danger of explosion if battery is incorrectly replaced.
Replace only with the type recommended by the
manufacturer.
Mishandling of batteries can cause electrolyte leakage and
may cause a fire.
Remove the battery if you do not intend to use the remote
control for a long period of time. Store in a cool, dark
place.
Do not heat or expose to flame.
Do not leave the battery(ies) in a car exposed to direct
sunlight for a long period of time with doors and windows
closed.
Do not take apart or short circuit.
Do not recharge alkaline or manganese batteries.
Do not use batteries if the covering has been peeled off.
When disposing of the batteries, please contact your local
authorities or dealer and ask for the correct method of
disposal.
NORSK
Produkt
For å redusere faren for brann, elektrisk støt eller skade på
apparatet:
Utsett ikke produktet for regn, fukt, drypping eller sprut.
Ikke plasser objekter som er fylt med væske, som vaser,
på apparatet.
Bruk kun anbefalt tilbehør.
Fjern ikke deksler.
Reparer ikke denne enheten selv, overlat service til
kvalifisert servicepersonell.
Vekselstrømnett
Nettstøpselet er trukket ut fra denne enheten.
Installer denne enheten slik at nettstøpselet umiddelbart kan
trekkes fra stikkontakten.
Produkt
Dette produktet anvender en laser. Betjening av kontroller
eller justering eller andre inngrep enn de beskrevet i denne
bruksanvisning kan føre til farlig bestråling.
Plasser ikke åpen ild, slik som levende lys, oppå apparatet.
Dette apparatet er beregnet for bruk under moderate
klimaforhold.
Plassering
For å redusere faren for brann, elektrisk støt eller skade på
apparatet:
Ikke plasser apparatet i en bokhylle, et innebygget
kabinett eller et annet lukket sted. Pass på at produktet er
godt ventilert.
Apparatets ventilasjonsåpninger må ikke dekkes til med
aviser, duker, gardiner eller lignende.
WARNING
CAUTION
ADVARSEL
FORSIKTIG
Product Identification Marking is located on the bottom of the
unit.
SC-HC39EC~RQT9944-R.book 2 ページ 2014年4月2日 水曜日 午後3時29分
3
RQT9944
ENGLISH
Table of contents
Safety precautions............................................ 2
Accessories....................................................... 3
Control reference guide ................................... 4
Connections ...................................................... 5
Inserting media ................................................. 6
Bluetooth
®
operations ...................................... 7
Media playback controls .................................. 9
Listening to the radio ..................................... 10
Sound adjustment .......................................... 11
Clock and Timer.............................................. 11
Others .............................................................. 12
Troubleshooting.............................................. 13
Unit and media care........................................ 14
About Bluetooth
®
............................................ 15
Playable media................................................ 15
Licenses .......................................................... 15
Attaching the unit to a wall (optional)........... 16
Specifications.................................................. 18
Accessories
Check the supplied accessories before using this unit.
About descriptions in these operating
instructions
Pages to be referred to are indicated as “l ±±”.
Unless otherwise indicated, operations are described using
the remote control.
1 Remote control
(N2QAYB000944)
1 Battery for remote control
1 AC mains lead
1 FM indoor antenna
Wall mounting accessories
1 Safety holder
1 Screw
2 Wall mount
brackets
Do not use AC mains lead with other equipment.
Product numbers provided in these operating instructions are
correct as of January 2014. These may be subject to change.
Disposal of Old Equipment and Batteries
Only for European Union and countries with recycling systems
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries must not be mixed with general household
waste.
For proper treatment, recovery and recycling of old products and used batteries, please take
them to applicable collection points in accordance with your national legislation.
By disposing of them correctly, you will help to save valuable resources and prevent any
potential negative effects on human health and the environment.
For more information about collection and recycling, please contact your local municipality.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
Note for the battery symbol (bottom symbol):
This symbol might be used in combination with a chemical symbol. In this case it complies with
the requirement set by the Directive for the chemical involved.
SC-HC39EC~RQT9944-R.book 3 ページ 2014年4月2日 水曜日 午後3時29分
4
RQT9944
Control reference guide
1 Standby/on switch (Í/I) (Í)
Press to switch the unit from on to standby mode or vice
versa.
In standby mode, the unit is still consuming a small
amount of power.
2 Select the audio source
On this unit:
On the remote control:
[ ]: “BLUETOOTH”
[USB/CD]: “CD” ,. “USB”
3 Basic playback control buttons
4 Adjust the volume (0 (min) to 50 (max))
5 Open or close the sliding door
6 Bluetooth
®
-pairing button
Press to select “BLUETOOTH” as the audio source.
Press and hold to enter pairing mode (l 7) or
disconnect a Bluetooth
®
device (l 8).
7 NFC touch area (l 7)
8 Port for USB devices / DC OUT terminal (l 6)
9 AUX IN jack (l 5)
10 Remote control signal sensor
Distance: Within approx. 7 m directly in front
Angle: Approx. 30o left and right
11 Display
12 Sliding door
13 Enter setup menu
14 Change the displayed information
15 Enter sound menu
16 Dim the display panel
Press again to cancel.
17 Mute the sound
Press again to cancel. “MUTE” is also cancelled when the
volume is adjusted or the unit is turned off.
18 Enter playback menu
19 Selection/OK
Top view
“CD” """"-. “BLUETOOTH” """"-. “USB”
^"""--" “AUX” (""-"" “FM” ("-""-}
[RADIO/AUX]: “FM”,. “AUX”
Using the remote control
Insert the battery so the terminals (i and j) match those
in the remote control.
Point it at the remote control signal sensor on this unit.
To avoid interference, please do not put any objects in front of
signal sensor.
(Alkaline or manganese
battery)
SC-HC39EC~RQT9944-R.book 4 ページ 2014年4月2日 水曜日 午後3時29分
5
RQT9944
ENGLISH
Connections
These speakers do not have magnetic shielding. Do not place them near a TV, personal computer or other magnetic devices.
Tape the antenna to a wall or column in a position with the least amount of interference.
If radio reception is poor, use a FM outdoor antenna with a right angle type connector (not supplied).
1 Connect an external music device using an audio
cable (not supplied).
Plug type: 3.5 mm stereo
2 Press [RADIO/AUX] to select “AUX” and start
playback on the connected device.
To select the sound input level of the
external device
1 While in AUX mode, press [SOUND] repeatedly to
select “INPUT LEVEL”.
2 Press [3, 4] to select “NORMAL” or “HIGH” and
then press [OK].
The factory default is “NORMAL”.
To improve sound distortion when “HIGH” is selected, select “NORMAL”.
Switch the equalizer off or turn the volume of the external device down to reduce the input signal. High level of input signal will
distort the sound.
For details, refer to the operating instructions of the device.
Connect an external music device
2
1
Connect the AC mains lead after all other connections are completed.
This unit consumes a small amount of AC power (l 18) even when turned off.
In the interest of energy conservation, if you will not be using this unit for an extended period of time,
unplug it from the mains socket.
Adhesive tape
(not supplied)
FM indoor antenna
(supplied)
To a mains socket
AC mains lead (supplied)
Connect the antenna.
Audio cable
(not supplied)
SC-HC39EC~RQT9944-R.book 5 ページ 2014年4月2日 水曜日 午後3時29分
6
RQT9944
Inserting media
Charging a device
Charging starts when a device (rated value: 5 V/1.5 A) is connected to the DC OUT terminal of this unit.
1 Turn the unit on.
2 Connect a device.
{. Confirm from the screen of the connected device, etc. to
make sure charging has started.
A cable compatible with your device is required. Use the
cable that comes with your device.
Even if you connect a cable compatible with the DC OUT
terminal of this unit, your device may not be charged. In that
case, use the charger that comes with the device.
Depending on your device, using other chargers may not
work. Check the operating instructions of your device before
use.
Do not connect a device with a rated value higher than 5 V/
1.5 A to this unit.
To check if charging is complete, look at the screen of the
connected device, etc.
Once fully charged, remove the USB cable from the DC OUT
terminal.
To continue charging during standby mode, make sure the
device has started charging before turning the unit to standby
mode.
When charging a depleted device, do not turn the unit to
standby mode until the device becomes operational.
Make sure that the unit does not fall when inserting or removing media.
When moving this unit, be sure to remove all media and turn this unit to standby mode.
Make sure to tilt the disc so as not to touch the sliding
door.
Do not open the sliding door manually.
The label side
Connecting a USB device
Insert the USB device directly. Do not use any USB extension cable.
Please disconnect the USB device if you finish using.
Before removing the USB device, select a source other than “USB”.
Inserting a CD
SC-HC39EC~RQT9944-R.book 6 ページ 2014年4月2日 水曜日 午後3時29分
7
RQT9944
ENGLISH
Bluetooth
®
operations
You can listen to the sound from the Bluetooth
®
audio device from this unit wirelessly.
Refer to the operating instructions of the Bluetooth
®
device for details.
If you intend to use an NFC (Near Field Communication)-compatible Bluetooth
®
device, proceed to “One-Touch
Connection (Connecting by NFC)”.
Preparation
Turn on the Bluetooth
®
feature of the device and
place the device near this unit.
Pairing with Bluetooth
®
devices
1 Press [ ] to select “BLUETOOTH”.
{. If “PAIRING” is indicated on the display, go to step 4.
To enter pairing mode*
2 Press [PLAY MENU] to select “PAIRING”.
3 Press [3, 4] to select “OK? YES” and then press
[OK].
To pair with a device
4 Select “SC-HC39” from the Bluetooth
®
device’s
Bluetooth
®
menu.
{. The name of the connected device is indicated on the
display for a few seconds.
5 Start playback on the Bluetooth
®
device.
* You can also enter pairing mode by pressing and holding
[ -PAIRING] on the unit.
Connecting a paired Bluetooth
®
device
1 Press [ ] to select “BLUETOOTH”.
{. “READY” is indicated on the display.
2 Select “SC-HC39” from the Bluetooth
®
device’s
Bluetooth
®
menu.
{. The name of the connected device is indicated on the
display for a few seconds.
3 Start playback on the Bluetooth
®
device.
If prompted for the passkey, input “0000”.
You can register up to 8 devices with this unit. If a 9th device
is paired, the device that has not been used the longest will
be replaced.
This unit can only be connected to one device at a time.
When “BLUETOOTH” is selected as the source, this unit will
automatically try and connect to the last connected
Bluetooth
®
device.
For NFC-compatible Bluetooth
®
devices (Android
TM
devices) only
Simply by touching an NFC (Near Field
Communication)-compatible Bluetooth
®
device on the
unit, you can complete all preparations, from
registering a Bluetooth
®
device to establishing a
connection.
Preparation
Turn on the NFC feature of the device.
Android device version lower than 4.1 requires the
installation of the app “Panasonic Music Streaming”
(free of charge).
1 Enter “Panasonic Music Streaming” in the search box
of Google Play
TM
to search, and then select
“Panasonic Music Streaming”.
2 Start the app “Panasonic Music Streaming” on the
device.
Follow on-screen instructions on your device.
Always use the latest version of the app.
1 Press [ ] to select “BLUETOOTH”.
2 Touch and hold your device on the NFC touch area
of this unit [ ]. (l 4)
Do not move the Bluetooth
®
device until it beeps, displays
a message or reacts in some way.
Once the Bluetooth
®
device has reacted, move the device
away from this unit.
When the registration and connection of the Bluetooth
®
device is complete, the name of the connected device is
indicated on the display for a few seconds.
The location of the NFC touch area differs depending on
the device. When a connection cannot be established
even if your Bluetooth
®
device has touched the NFC
touch area of this unit, change the position of the device.
The condition may also improve if you download the
dedicated app “Panasonic Music Streaming” and start it
up.
3 Start playback on the Bluetooth
®
device.
If you touch another device to this unit, you can update the
Bluetooth
®
connection. The previously connected device will
be disconnected automatically.
When the connection is established, playback may start
automatically depending on the type of device being used.
The One-Touch Connection may not work properly
depending on the type of device being used.
Connecting via Bluetooth
®
menu
One-Touch Connection
(Connecting by NFC)
SC-HC39EC~RQT9944-R.book 7 ページ 2014年4月2日 水曜日 午後3時29分
8
RQT9944
You can change the transmission mode to prioritise
transmission quality or sound quality.
Preparation
Press [ ] to select “BLUETOOTH”.
If a Bluetooth
®
device is already connected,
disconnect it.
1 Press [PLAY MENU] repeatedly to select
“LINK MODE”.
2 Press [3, 4] to select the mode and then press
[OK].
MODE 1: Emphasis on connectivity
MODE 2: Emphasis on sound quality
Select “MODE 1” if the sound is interrupted.
The factory default is “MODE 2”.
If the sound input level from the Bluetooth
®
device is
too low, change the input level setting.
Preparation
Connect a Bluetooth
®
device.
1 Press [PLAY MENU] repeatedly to select “INPUT
LEVEL”.
2 Press [3, 4] to select the level and then press
[OK].
“LEVEL 0” ,. “LEVEL i1” ,. “LEVEL i2”
^---------------------------------------------------------J
Select “LEVEL 0” if the sound is distorted.
The factory default is “LEVEL 0”.
1 While a Bluetooth
®
device is connected:
Press [PLAY MENU] repeatedly to select
“DISCONNECT?”.
2 Press [3, 4] to select “OK? YES” and then press
[OK].
You can also disconnect the Bluetooth
®
device by pressing
and holding [ -PAIRING] on the unit.
The Bluetooth
®
device will be disconnected if a different
audio source (e.g., “CD”) is selected.
Bluetooth
®
transmission mode
Bluetooth
®
input level
Disconnecting a Bluetooth
®
device
SC-HC39EC~RQT9944-R.book 8 ページ 2014年4月2日 水曜日 午後3時29分
9
RQT9944
ENGLISH
Media playback controls
The following marks indicate the availability of the
feature.
Preparation
Turn the unit on.
Insert the media or connect the Bluetooth
®
device.
Press [USB/CD] or [ ] to select the audio source.
To display information
Press [DISPLAY] repeatedly.
To use this unit’s remote control with a Bluetooth
®
device, the
Bluetooth
®
device must support AVRCP (Audio Video
Remote Control Profile).
Depending on the status of the device, some controls may
not work.
Maximum number of displayable characters: approx. 30
This unit supports ver. 1.0, 1.1 and 2.3 ID3 tags. Text data
that is not supported will not be displayed or will be shown
differently.
Album and track indication for MP3 files.
Select the playback mode.
1 Press [PLAY MENU] to select “PLAYMODE” or
“REPEAT”.
2 Press [3, 4] to select the setting and then press
[OK].
During random play, you cannot skip to the previous track.
The mode is cancelled when you open the sliding door.
[CD]: CD audio in CD-DA format and a CD that
contains MP3 files (l 15)
[USB]: USB devices containing MP3 files (l 15)
[Bluetooth]: Connected Bluetooth
®
device
Basic controls
([CD], [USB], [Bluetooth])
Play Press [1/;].
Stop Press [].
[USB]: The position is memorised and
“RESUME” is displayed.
Pause Press [1/;].
Press again to restart play.
Skip Press [:/6] or [5/9] to skip
track.
[CD], [USB] Press [3] or [4] to skip
the MP3 album.
Search During play or pause, press and hold
[:/6] or [5/9].
“A _ _ _”: MP3 album number.
“T _ _ _”: MP3 track number.
“ _ ” stands for the album or track number.
“”:
This indication is also used to refer to an album.
“”:
This indication is also used to refer to a track.
Playback modes ([CD], [USB])
PLAYMODE
OFF
PLAYMODE
Cancels the play mode setting.
1-TRACK Only plays the selected track.
“1”, “ ” is displayed.
(Skip to the desired track.)
1-ALBUM Only plays the selected MP3 album.
“1”, “ ” is displayed.
RANDOM Plays the contents randomly.
“RND” is displayed.
1-ALBUM
RANDOM
Plays the tracks in the selected
MP3 album randomly.
Press [3] or [4] to select the MP3
album.
“1”, “ ”, “RND” is displayed.
REPEAT
ON REPEAT Turns on repeat mode.
`” is displayed.
OFF
REPEAT
Turns off repeat mode.
SC-HC39EC~RQT9944-R.book 9 ページ 2014年4月2日 水曜日 午後3時29分
10
RQT9944
Listening to the radio
You can preset up to 30 channels.
Preparation
Make sure that the antenna is connected. (l 5)
Turn the unit on.
Press [RADIO/AUX] to select “FM”.
A station previously stored is overwritten when another
station is stored in the same channel preset.
1 Press [PLAY MENU] to select “A.PRESET”.
2 Press [3, 4] to select “LOWEST” or “CURRENT”
and then press [OK].
LOWEST:
To begin auto preset with the lowest frequency
(FM 87.50).
CURRENT:
To begin auto preset with the current frequency.*
{. The tuner starts to preset all the stations it can receive
into the channels in ascending order.
* To change the frequency, refer to “Manual tuning and
presetting”.
1 Press [PLAY MENU] repeatedly to select
“TUNEMODE”.
2 Press [3, 4] to select “PRESET” and then press
[OK].
3 Press [:/6] or [5/9] to select the
channel.
Manual tuning and presetting
Select a radio broadcast.
1 Press [PLAY MENU] repeatedly to select
“TUNEMODE”.
2 Press [3, 4] to select “MANUAL” and then press
[OK].
3 Press [:/6] or [5/9] to tune to the
required station.
To start automatic tuning, press and hold [:/6] or
[5/9] until the frequency starts scrolling. Tuning
stops when a station is found.
To preset the channel
4 While listening to the radio broadcast, press [OK].
5 Press [3, 4] to select the channel and then press
[OK].
To improve FM sound quality
1 While receiving FM broadcasts, press
[PLAY MENU] repeatedly to select “FM MODE”.
2 Press [3, 4] to select “MONO” and then press
[OK].
This setting can be preset and memorised. To do so,
continue to step 4 of “Manual tuning and presetting”.
Select “STEREO” in step 2 to return to stereo broadcasts.
“MONO” is cancelled if the frequency is changed.
To display the current FM signal status
While receiving FM signal, press [PLAY MENU]
repeatedly to display “FM STATUS” and then press
[OK].
To display RDS text data
Press [DISPLAY] to display the text data.
Each time you press the button:
“STEREO” is displayed when this unit tunes to a stereo
broadcast.
The unit can display the text data transmitted by the radio
data system (RDS) available in some areas. (RDS displays
may not be available if reception is poor.)
Presetting stations automatically
Listening to a preset channel
“FM ST”: The FM signal is tuned and in stereo.
“FM”: There is no tuned signal or the FM signal
is in monaural.
“FM MONO”: “MONO” is selected in step 2 of “To
improve FM sound quality” (l above).
“PS”: Programme service
“PTY”: Programme type
“FREQ”: Frequency display
SC-HC39EC~RQT9944-R.book 10 ページ 2014年4月2日 水曜日 午後3時29分
11
RQT9944
ENGLISH
Sound adjustment
The following sound effects can be added to the audio
output.
1 Press [SOUND] repeatedly to select the effect.
2 Press [3, 4] to select the setting and then press
[OK].
You may experience a reduction in sound quality when these
effects are used with some sources. If this occurs, turn the
sound effects off.
When “AUX” is selected as the source, you can select
“INPUT LEVEL” to adjust the sound input level of the
external device. (l 5)
Clock and Timer
This is a 24-hour clock.
1 Press [SETUP] repeatedly to select “CLOCK”.
2 Press [3, 4] to set the time and then press [OK].
To display the clock, press [SETUP] repeatedly to select
“CLOCK” and then press [OK] once. The time is displayed for
10 seconds.
(During standby, press [DISPLAY] once.)
The clock is reset when there is a power failure or when the
AC mains lead is removed.
Reset the clock regularly to maintain accuracy.
You can set the timer so this unit turns on at a certain
time every day.
Preparation
Set the clock.
Setting the timer
1 Press [SETUP] repeatedly to select “TIMER ADJ”.
2 Press [3, 4] to set the starting time (“ON TIME”)
and then press [OK].
3 Press [3, 4] to set the finishing time
(“OFF TIME”) and then press [OK].
4 Press [3, 4] to select the music source*
and then
press [OK].
Turning the timer on
1 Prepare the selected music source and set the
desired volume.
2 Press [SETUP] repeatedly to select “TIMER SET”.
3 Press [3, 4] to select “SET” and then press [OK].
F” is displayed.
To turn the timer off, select “OFF”.
4 Press [Í] to turn the unit to standby mode.
To display the timer settings, press [SETUP] repeatedly to
select “TIMER ADJ” and then press [OK] once.
The music source and volume will also be displayed if the
timer is turned on.
During standby, if the timer is turned on, press [DISPLAY]
twice to display the settings.
This unit can be used as normal after the timer is set,
however:
Turn the unit to standby mode before the timer start time.
Even if the audio source or the volume is changed, the
timer will still use the audio source and volume that was
set when the timer was turned on.
The sleep timer can turn the unit off after a set time.
1 Press [SETUP] to select “SLEEP”.
2 Press [3, 4] to set the time (in minutes) and then
press [OK].
“SLEEP 30” ,. “SLEEP 60” ,. “SLEEP 90” ,. “SLEEP 120”
^------------------. “OFF” (Cancel) (------------------J
The remaining time is indicated on the unit’s display except
when other operations are performed.
The play timer and sleep timer can be used together. The
sleep timer is always the main timer on the unit.
“PRESET EQ”
(Preset Equalizer)
“HEAVY” (heavy), “SOFT” (soft),
“CLEAR” (clear), “VOCAL”
(vocal) or “FLAT” (flat/off).
The factory default is “HEAVY”.
“BASS” (Bass) or
“TREBLE” (Treble)
Adjust the level (j4 to i4).
“D.BASS”
(Dynamic Bass)
“ON D.BASS” or “OFF D.BASS”.
The factory default is
“ON D.BASS”.
“SURROUND”
(Surround)
“ON SURROUND” or
“OFF SURROUND”.
The factory default is
“OFF SURROUND”.
Setting the clock
Play timer
* “CD”, “USB”, “FM” and “AUX” can be set as the music
source.
Sleep timer
SC-HC39EC~RQT9944-R.book 11 ページ 2014年4月2日 水曜日 午後3時29分
12
RQT9944
Others
As a factory default, this unit will turn to standby mode
automatically if there is no sound and it is not being
used for approximately 20 minutes.
To cancel this function
1 Press [SETUP] repeatedly to select “AUTO OFF”.
2 Press [3, 4] to select “OFF” and then press [OK].
To turn the function on, select “ON” in step 2.
This setting cannot be selected when “FM” is the source.
When connected to a Bluetooth
®
device, the function does
not work.
When “SC-HC39” is selected from a paired Bluetooth
®
device’s Bluetooth
®
menu, this unit will turn on
automatically from standby mode and establish a
Bluetooth
®
connection.
1 Press [SETUP] repeatedly to select “BLUETOOTH
STANDBY”.
2 Press [3, 4] to select “ON” and then press [OK].
To turn the function off, select “OFF” in step 2.
When other Panasonic equipment responds to the
supplied remote control, change the remote control
code.
1 Press [USB/CD] to select “CD”.
2 While pressing and holding [SELECTOR] on the
unit, press and hold [USB/CD] on the remote
control until the unit’s display shows “REMOTE 2”.
3 Press and hold [OK] and [USB/CD] on the remote
control for at least 4 seconds.
To change the mode back to “REMOTE 1”, press [USB/CD]
to select “CD” and then repeat the step 2 and 3 but replace
[USB/CD] with [ ].
Occasionally, Panasonic may release updated
software for this unit that may add or improve the way
a feature operates. These updates are available free of
charge.
For more details, refer to the following website.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
Checking the software version
The version of the installed software is displayed.
Press [SETUP] repeatedly to select “SW VER.” and
then press [OK].
Press [OK] to exit.
Auto off function
Bluetooth
®
standby
Changing the unit and remote
control code
Software update
SC-HC39EC~RQT9944-R.book 12 ページ 2014年4月2日 水曜日 午後3時29分
13
RQT9944
ENGLISH
Troubleshooting
Before requesting service, make the following checks. If
you are uncertain about some of the check points, or if the
solutions indicated in the following guide does not resolve
the issue, then consult your dealer for instructions.
Humming heard during playback.
If an AC mains lead or fluorescent lights are near the cords, then
keep other appliances and cords away from the cables.
The unit does not work.
One of the unit’s safety devices may have been activated.
Reset the unit as follows:
1 Press [Í/I] on the unit to switch the unit to standby.
If the unit does not switch to standby, press [Í/I] on the unit
for approximately 10 seconds. The unit is forcibly switched
to standby. Alternatively, disconnect the AC mains lead, wait
for at least 3 minutes, then reconnect it.
2 Press [Í/I] on the unit to switch it on. If the unit still cannot be
operated, consult the dealer.
MP3 cannot be read.
You may not be able to play MP3 if you have copied a
multi-session disc that has no data between sessions.
When creating a multi-session disc, it is necessary to close the session.
The amount of data on the disc is too small. Set the amount of
data to above 5 MB.
Charging does not start during standby mode.
Turn the unit on. Check the charging has started, and then turn
the unit to standby mode. (l 6)
Noise is heard.
When a device is connected to both the AUX IN jack and the DC
OUT terminal, noise may be generated depending on the device.
In this case, remove the USB cable from the DC OUT terminal.
The remote control does not work properly.
The battery is depleted or inserted incorrectly. (l 4)
Incorrect display or play does not start.
Make sure that the disc is compatible with this unit. (l 15)
There is moisture on the lens. Wait for about an hour and then try again.
No response when [1/;] is pressed.
Disconnect the USB device and then reconnect it. Alternatively,
turn the unit off and on again.
The USB drive or its contents cannot be read.
The USB drive format or its contents is/are not compatible with the
unit (l 15).
The USB host function of this product may not work with some
USB devices.
Slow operation of the USB flash drive.
Large file size or high memory USB flash drive takes longer time
to read.
The elapsed time displayed is different from the
actual play time.
Copy the data to another USB device or backup the data and
reformat the USB device.
Static or noisy reception is heard while listening to
a radio broadcast.
Confirm the antenna is properly connected. (l 5)
Adjust the position of the antenna.
Try to keep a certain amount of distance between the antenna and
AC mains lead.
Try using an outdoor antenna if there are buildings or mountains
nearby. (l 5)
Turn the TV or other audio players off or separate it from this unit.
Keep this unit away from mobile phones if there is interference.
Pairing cannot be completed.
Check the Bluetooth
®
device condition.
The device cannot be connected.
The pairing of the device was unsuccessful or the registration has
been replaced. Try re-pairing the device. (l 7)
This unit might be connected to a different device. Disconnect the
other device and try re-pairing the device. (l 7)
The device is connected, but audio cannot be
heard through this unit.
For some built-in Bluetooth
®
devices, you have to set the audio
output to “SC-HC39” manually. Read the operating instructions for
the device for details.
The sound is interrupted.
The device is out of the 10 m communication range. Place the
Bluetooth
®
device closer to this unit.
Remove any interference between this unit and the device.
Other devices that use the 2.4 GHz frequency band, such as
wireless routers, microwaves, cordless phones, etc. are
interfering. Place the Bluetooth
®
device closer to this unit and
distance it from the other devices.
Select “MODE 1” for stable communication. (l 8)
The One-Touch Connection (NFC feature) is not
working.
Make sure the unit and the NFC feature of the device are turned
on. (l 7)
To return all settings to the factory defaults
When the following situations occur, reset the
memory:
There is no response when buttons are pressed.
You want to clear and reset the memory contents.
1 Disconnect the AC mains lead. (Wait for at least
3 minutes before proceeding to step 2.)
2 While pressing and holding down [Í/I] on the
unit, reconnect the AC mains lead.
Keep holding down [Í/I] until “---------” appears on the
display.
3 Release [Í/I].
All the settings are returned to the factory defaults. You will
need to reset the memory items.
General
Remote control
Disc
USB
Radio
Bluetooth
®
SC-HC39EC~RQT9944-R.book 13 ページ 2014年4月2日 水曜日 午後3時29分
14
RQT9944
The following messages or service numbers may
appear on the units display.
“--:--”
You plugged the AC mains lead in for the first time or there was a
power failure recently. Set the time (l 11).
“ADJUST CLOCK”
Clock is not set. Adjust the clock accordingly.
“ADJUST TIMER”
Play timer is not set. Adjust the play timer accordingly.
“AUTO OFF”
The unit has been left unused for about 20 minutes and will shut
down within a minute. Press any button to cancel it.
“ERROR”
Incorrect operation is performed. Read the instructions and try
again.
“F” (“ ” stands for a number.)
There is a problem with this unit.
Write down the displayed number, disconnect the AC mains lead
and consult your dealer.
“ILLEGAL OPEN”
Sliding door is in the wrong position. Turn the unit off and on
again. If this display appears again, consult the dealer.
“NODEVICE”
The USB device is not inserted correctly. Read the instructions
and try again (l 6).
“NO DISC”
Insert the disc to be played (l 6).
“NO PLAY”
A CD that is not in CD-DA or MP3 format is inserted. It cannot be
played.
Examine the content. You can only play supported format. (l 15)
The files in the USB device can be corrupted. Format the USB
device and try again.
The unit may have a problem. Turn the unit off and then on again.
“PLAYERROR”
You played an unsupported MP3 file. The system will skip that
track and play the next one.
“READING”
The unit is checking the CD/USB information. After this display
has disappeared, start operating.
“REMOTE ” (“ ” stands for a number.)
The remote control and this unit are using different codes. Change
the code on the remote control.
When “REMOTE 1” is displayed, press and hold [OK] and [ ]
for at least 4 seconds.
When “REMOTE 2” is displayed, press and hold [OK] and
[USB/CD] for at least 4 seconds.
“USB OVER CURRENT ERROR”
The USB device is drawing too much power. Select a source other
than “USB”, remove the USB and turn the unit off.
“VBR”
The system cannot show the remaining play time for variable bit
rate (VBR) tracks.
Unit and media care
Pull out the AC mains lead from the outlet before
maintenance.
Clean this unit with a soft, dry cloth
When dirt is heavy, wring a wet cloth tightly to wipe the dirt,
and then wipe it with a dry cloth.
When cleaning the speaker covers, use a fine cloth.
Do not use tissues or other materials that can fall apart.
Small pieces may get stuck inside the speaker cover.
Never use alcohol, paint thinner or benzine to clean this unit.
Before using chemically treated cloth, carefully read the
cloth’s instructions.
Maintenance of the lens
Clean the lens regularly to prevent malfunctions. Use a dust
blower to remove dust and a cotton swab if it is extremely
dirty.
You cannot use a CD type lens cleaner.
Do not leave the sliding door open for prolonged periods of
time. This will cause the lens to get dirty.
Be careful not to touch the lens with your fingers.
Clean discs
Wipe with a damp cloth and then wipe dry.
Disc handling precautions
Handle discs by the edges to avoid inadvertent scratches or
fingerprints on the disc.
Do not attach labels or stickers to discs.
Do not use record cleaning sprays, benzine, thinner, static
electricity prevention liquids or any other solvent.
Do not use the following discs:
Discs with exposed adhesive from removed stickers or
labels (rented discs etc.).
Discs that are badly warped or cracked.
Irregularly shaped discs, such as heart shapes.
To dispose or transfer this unit
The unit may keep the user settings information in the
unit. If you discard this unit either by disposal or
transfer, then follow the procedure to return all the
settings to the factory defaults to delete the user
settings.
(l 13, “To return all settings to the factory defaults”)
The operation history may be recorded in the
memory of this unit.
Messages
DO DO NOT
Lens
SC-HC39EC~RQT9944-R.book 14 ページ 2014年4月2日 水曜日 午後3時29分
15
RQT9944
ENGLISH
About Bluetooth
®
Frequency band used
This system uses the 2.4 GHz frequency band.
Certification of this device
This system conforms to frequency restrictions and
has received certification based on frequency laws.
Thus, a wireless permit is not necessary.
The actions below are punishable by law in some
countries:
Taking apart or modifying the system.
Removing specification indications.
Restrictions of use
Wireless transmission and/or usage with all
Bluetooth
®
equipped devices is not guaranteed.
All devices must conform to standards set by
Bluetooth SIG, Inc.
Depending on the specifications and settings of a
device, it can fail to connect or some operations can
be different.
This system supports Bluetooth
®
security features.
But depending on the operating environment and/or
settings, this security is possibly not sufficient.
Transmit data wirelessly to this system with caution.
This system cannot transmit data to a Bluetooth
®
device.
Range of use
Use this device at a maximum range of 10 m. The
range can decrease depending on the environment,
obstacles or interference.
Interference from other devices
This system may not function properly and troubles
such as noise and sound jumps may arise due to
radio wave interference if this system is located too
close to other Bluetooth
®
devices or the devices that
use the 2.4 GHz band.
This system may not function properly if radio waves
from a nearby broadcasting station, etc. is too
strong.
Intended usage
This system is for normal, general use only.
Do not use this system near an equipment or in an
environment that is sensitive to radio frequency
interference (example: airports, hospitals,
laboratories, etc).
Playable media
A disc with the CD Logo.
This unit can play back discs that conform to the CD-DA
format.
The unit may not be able to play some discs due to the
condition of the recording.
Before playback, finalise the disc on the device it was
recorded on.
This unit does not guarantee connection with all USB
devices.
FAT12, FAT16 and FAT32 file systems are supported.
This unit supports USB 2.0 full speed.
This unit can support USB devices of up to 32 GB.
Supported format: Files with the extension “.mp3” or “.MP3”.
Compatible compression rate: Between 16 kbps and
320 kbps (stereo).
Depending on how you create the MP3 files, they may not
play in the order you numbered them or may not play at all.
CD-R/RW
Maximum number of tracks and albums: 999 tracks and 254
albums (Excluding Root folder).
Disc formats: ISO9660 level 1 and level 2 (except for
extended formats).
If the disc includes both MP3 and normal audio data
(CD-DA), the unit plays the type recorded in the inner part of
the disc.
This unit cannot play files recorded using packet write.
USB device
Maximum number of tracks and albums: 8000 tracks and 799
albums (Excluding Root folder).
Only one memory card will be selected when connecting a
multiport USB card reader, typically the first memory card
inserted.
Licenses
Panasonic bears no responsibility for data and/or
information that is compromised during a
wireless transmission.
Compatible CD
Compatible USB devices
Compatible MP3 files
The Bluetooth
®
word mark and logos are owned by the
Bluetooth SIG, Inc. and any use of such marks by Panasonic
Corporation is under license.
Other trademarks and trade names are those of their respective
owners.
Google Play and Android are trademarks of Google Inc.
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
SC-HC39EC~RQT9944-R.book 15 ページ 2014年4月2日 水曜日 午後3時29分
16
RQT9944
Attaching the unit to a wall
(optional)
This unit can be wall mounted using the supplied wall
mount brackets, etc. Make sure that the wall and the
screws used for securing to the wall are capable of
supporting at least 33 kg. The screws and other items
are not supplied as the type and size will vary with
each installation.
Refer to step 5 of “Wall mount instructions” for details
about the required screws.
As an additional protective measure, attach the unit
to the wall with the fall prevention cord.
Supplied accessories
1 Safety holder
1 Screw
2 Wall mount brackets
Additionally required accessories
(commercially available)
4 Wall mount bracket fixing screws
1 Safety holder fixing screw
1 Fall prevention cord*
1 Screw eye
* Use a cord that is capable of supporting over 33 kg
(with a diameter of about 1.5 mm).
1 Detach the stand from the unit.
Unscrew the fixing screw at the bottom of the unit.
Gently pull the stand off the unit as illustrated.
Keep the removed screw and the stand in a safe place.
2 Fix the safety holder onto the unit with the screw
(supplied).
Screw tightening torque: 50 N0cm to 70 N0cm.
3 Attach the fall prevention cord (not supplied) to this
unit.
Installation accessories
Keep the safety holder out of reach of children to
prevent swallowing.
Keep the screws out of reach of children to prevent
swallowing.
Keep the wall mount brackets out of reach of children
to prevent swallowing.
Safety precautions
Professional installation is required.
The installation should never be done by any
other than a qualified installation specialist.
PANASONIC DISCLAIMS ANY PROPERTY
DAMAGE AND/OR SERIOUS INJURY,
INCLUDING DEATH RESULTING FROM
IMPROPER INSTALLATION OR INCORRECT
HANDLING.
WARNING:
To prevent injury, this apparatus must be securely
attached to the wall in accordance with the
installation instructions.
Wall mount instructions
Before installation, turn the unit off and disconnect the
AC mains lead from the mains socket.
Stand
Fixing screw
Soft blanket or cloth
Screw
(supplied)
Cord
(not supplied)
SC-HC39EC~RQT9944-R.book 16 ページ 2014年4月2日 水曜日 午後3時29分
17
RQT9944
ENGLISH
4 Measure and mark the position of both sides of the
wall mount brackets.
Use figures below to identify the screwing positions.
The position to attach the wall mount brackets
Space required
5 Attach the wall mount bracket to both sides of the
wall with two screws (not supplied).
Use a level to ensure both wall mount brackets are
level.
6 Hook the unit securely onto the wall mount
brackets with both hands.
After hanging the unit, release your hands carefully to
confirm the unit sits securely on the wall mount
brackets.
7 Drive the safety holder fixing screw (not supplied)
to secure the safety holder onto the wall.
Refer to step 5 for requirements before screwing.
8 Attach the fall prevention cord (not supplied) to the
wall.
Make sure that the slack of the cord is minimal.
204 mm
13 mm
500 mm
75 mm
142 mm
154 mm
100 mm
142
mm
300 mm
100 mm
At least 30 mm
7.5 mm to
9.4 mm
4 mm
Wall mount bracket
Connect the antenna and the AC mains lead to the unit
before hanging the unit onto the wall. (l 5)
Wall
Safety holder fixing screw
(not supplied)
Safety holder
Fix to the wall
Cord (not supplied)
Screw eye (not supplied)
Wall
SC-HC39EC~RQT9944-R.book 17 ページ 2014年4月2日 水曜日 午後3時29分
18
RQT9944
Specifications
Specifications are subject to change without notice.
Mass and dimensions are approximate.
Total harmonic distortion is measured by a digital spectrum
analyzer.
*1: “BLUETOOTH STANDBY” is “OFF”.
*2: No device is connected to the USB port before turning to
standby mode.
*3: MPEG-1 Layer 3, MPEG-2 Layer 3
GENERAL
Power consumption 26 W
Power consumption in standby mode*
1, 2
Approx. 0.2 W
(When “BLUETOOTH STANDBY” is “ON”)*
2
Approx. 0.3 W
Power supply
AC 220 V to 240 V, 50 Hz
Dimensions (WkHkD)
500 mmk205 mmk92 mm
Mass Approx. 2.5 kg
Operating temperature range
0 oC to r40 oC
Operating humidity range
35 % to 80 % RH (no condensation)
AMPLIFIER SECTION
Output power
RMS Output Power Stereo mode
Front Ch (both ch driven)
20 W per channel (8 ), 1 kHz, 10 % THD
Total RMS Stereo mode power
40 W
TUNER SECTION
Preset Memory FM 30 stations
Frequency Modulation (FM)
Frequency range
87.50 MHz to 108.00 MHz (50 kHz step)
Antenna terminals
75 (unbalanced)
DISC SECTION
Disc played (8 cm or 12 cm)
CD, CD-R/RW (CD-DA, MP3*
3
)
Pick up
Wavelength 790 nm (CD)
[NORSK]
Bølgelengde 790 nm (CD)
Laserstyrke Ingen farlig stråling sendes ut
(med sikkerhets-beskyttelse)
SPEAKER SYSTEM SECTION
Speaker unit(s)
Full range
6.5 cm Cone typek1 per channel
Passive Radiator
8cmk2 per channel
Impedance 8
TERMINAL SECTION
USB Port
DC OUT 5V 1.5A
USB Standard
USB 2.0 full speed
Media file format support
MP3 (¢.mp3)
USB device file system
FAT12, FAT16, FAT32
AUX IN
Stereo, 3.5 mm jack
BLUETOOTH SECTION
Version Bluetooth
®
Ver.2.1+EDR
Class Class 2
Supported Profiles
A2DP, AVRCP
Operating Frequency
2.4 GHz band FH-SS
Operation Distance
10 m Line of sight
SC-HC39EC~RQT9944-R.book 18 ページ 2014年4月2日 水曜日 午後3時29分
19
RQT9944
ENGLISH
SC-HC39EC~RQT9944-R.book 19 ページ 2014年4月2日 水曜日 午後3時29分
20
RQT9944
Zasady bezpieczeństwa
Urządzenie
Aby ograniczyć niebezpieczeństwo pożaru, porażenia
prądem lub uszkodzenia urządzenia,
Nie należy wystawiać urządzenia na działanie deszczu,
wilgoci, kapanie lub zachlapanie.
Na urządzeniu nie należy ustawiać żadnych naczyń
zawierających płyny, takich jak wazony.
–Należy korzystać wyłącznie z zalecanych akcesoriów.
Nie należy demontować obudowy urządzenia.
Nie należy podejmować prób samodzielnej naprawy.
Naprawę urządzenia należy zlecić wykwalifikowanym
pracownikom serwisu.
–Należy uważać, aby do wnętrza urządzenia nie dostały
się metalowe przedmioty.
Na urządzeniu nie wolno umieszczać żadnych ciężkich
przedmiotów.
Przewód zasilania
Aby ograniczyć niebezpieczeństwo pożaru, porażenia
prądem lub uszkodzenia urządzenia,
–Należy się upewnić, że napięcie źródła zasilania
odpowiada napięciu podanemu na urządzeniu.
–Dokładnie podłączyć wtyczkę przewodu zasilającego do
gniazda ściennego.
Nie wolno ciągnąć za przewód, zginać go ani kłaść na nim
ciężkich przedmiotów.
Nie wolno dotykać wtyczki mokrymi rękami.
Przy odłączaniu przewodu należy chwycić za wtyczkę.
Nie wolno podłączać urządzenia do uszkodzonego
gniazda ściennego oraz gdy wtyczka przewodu
zasilającego jest uszkodzona.
Wtyczka zasilania umożliwia odłączenie urządzenia.
Zainstaluj to urządzenie w taki sposób, aby mo
żliwe było
natychmiastowe odłączenie wtyczki zasilania od gniazda
zasilania.
Urządzenie
W tym urządzeniu znajduje się laser. Wykonywanie regulacji
innych niż opisane lub postępowanie w sposób
nieprzewidziany w instrukcji obsługi grozi niebezpiecznym
naświetleniem promieniami lasera.
Nie należy umieszczać na urządzeniu źródeł otwartego
ognia, takich jak zapalone świece.
To u rządzenie może odbierać zakłócenia wywołane użyciem
telefonu komórkowego. Jeżeli takie zakłócenia wystąpią,
wskazane jest zwiększenie odległości pomiędzy
urządzeniem a telefonem komórkowym.
Urządzenie jest przeznaczone do używania w klimacie
umiarkowanym.
Wybór miejsca
Urządzenie należy ustawić na równej powierzchni.
Aby ograniczyć niebezpieczeństwo pożaru, porażenia
prądem lub uszkodzenia urządzenia,
Niniejszego urządzenia nie należy instalować lub
umieszczać w szafce na książki, zabudowanej szafce lub
innej ograniczonej przestrzeni, w celu zapewnienia dobrej
wentylacji.
Nie należy zasłaniać otworów wentylacyjnych urządzenia
gazetami, obrusami, zasłonami i podobnymi
przedmiotami.
–Urządzenie należy chronić przed bezpośrednim
działaniem promieni słonecznych, wysoką temperaturą,
wysoką wilgotnością oraz nadmiernymi drganiami.
Bateria
Istnieje niebezpieczeństwo wybuchu w przypadku, gdy
baterie zostaną nieprawidłowo włożone. Baterie należy
wymieniać wyłącznie na baterie typu zalecanego przez
producenta.
Nieprawidłowe obchodzenie się z bateriami może prowadzić
do wycieku elektrolitu i może być także przyczyną pożaru.
Baterię należy wyjąć, jeżeli pilot nie będzie używany przez
dłuższy czas. Należy ją przechowywać w chłodnym,
ciemnym miejscu.
Nie ogrzewaj i nie wrzucaj do ognia.
Nie należy pozostawiać baterii przez dłuższy czas w
samochodzie z zamkniętymi drzwiami i oknami
wystawionym na bezpośrednie działanie promieni
słonecznych.
Nie demontuj i nie powoduj zwarcia.
Baterii alkalicznych lub manganowych nie należy ładować
ponownie.
Nie używaj baterii, z których usuni
ęta została osłona.
W przypadku utylizacji baterii, należy się skontaktować z
lokalnymi władzami lub ze sprzedawcą celem uzyskania
informacji o prawidłowym sposobie postępowania.
OSTRZEËENIE
UWAGA
Oznaczenia identyfikacyjne produktu znajdują się na
spodzie urządzenia.
Deklaracja zgodności
Niniejszym “Panasonic Corporation” deklaruje, że ten
produkt jest zgodny z istotnymi wymaganiami i innymi
odnośnymi postanowieniami dyrektywy 1999/5/WE.
Klienci mogą pobrać oryginalną deklarację zgodności
naszych produktów z serwera deklaracji zgodności:
http://www.doc.panasonic.de
Kontakt się z autoryzowanym przedstawicielem: Panasonic
Marketing Europe GmbH,
Panasonic Testing Centre, Winsbergring 15, 22525
Hamburg, Niemcy
Ten produkt jest przeznaczony dla użytkownika ogólnego.
(Kategoria 3)
SC-HC39EC~RQT9944-R.book 20 ページ 2014年4月2日 水曜日 午後3時29分
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76

Panasonic SC-HC39 Instrukcja obsługi

Kategoria
Odbiorniki muzyczne Bluetooth
Typ
Instrukcja obsługi
Ten podręcznik jest również odpowiedni dla