Panasonic SC-HC38 Operating Instructions Manual

Marka: Panasonic

Model: SC-HC38

Typ: Operating Instructions Manual

RQT9746-1R

POLSKIČESKY ENGLISHESPAÑOL

Operating Instructions

Instrukcja obsługi

Návod k obsluze

Instrucciones de funcionamiento

Thank you for purchasing this product.

Please read these instructions carefully before using

this product, and save this manual for future use.

Dziękujemy za zakupienie tego produktu.

Przed przystąpieniem do eksploatacji opisywanego

produktu należy dokładnie przeczytać niniejsze

zalecenia i zachować instrukcję obsługi do wglądu.

Děkujeme, že jste si zakoupil tento výrobek.

Před použitím tohoto produktu si pečlivě přečtěte tyto

pokyny a celý návod si uložte pro pozdější použití.

Muchísimas gracias por haber adquirido este aparato.

Lea cuidadosamente estas instrucciones antes de usar

este producto, y guarde este manual para usarlo en el

futuro.

Compact Stereo System

Kompaktowy zestaw stereo

Kompaktní stereo systém

Sistema estéreo compacto

Model No. SC-HC38

Included Installation Instructions

(l 2 and 16, 17)

The installation work should be done by a

qualified installation specialist.

Before commencing work, carefully read these

installation instructions and the operating instructions

to ensure that installation is performed correctly.

(Please keep these instructions. You may need them

when maintaining or moving this unit.)

Załączone instrukcje instalacji

(l 20 i 34, 35)

Instalację powinien przeprowadzić wyłącznie

wykwalifikowany specjalista.

Przed rozpoczęciem pracy należy się dokładnie

zapoznać z instrukcją instalacji oraz z instrukcją

obsługi, aby się upewnić, że instalacja została

przeprowadzona prawidłowo.

(Proszę zachować niniejszą instrukcję. Będzie ona

potrzebna podczas serwisowania lub przenoszenia

urządzenia.)

Přiložené pokyny k instalaci (l 36 a 50, 51)

Instalační práce musí být provedeny

kvalifikovaným instalatérským odborníkem.

Před zahájením instalace si pečlivě pročtěte tyto

pokyny k instalaci a návod k obsluze, abyste instalaci

provedli opravdu správně.

(Tyto pokyny si uschovejte. Můžete je potřebovat při

údržbě nebo přesouvání tohoto zařízení.)

Se incluyen instrucciones de instalación

(l 52 y 66, 67)

La instalación debe ser realizada por un

especialista calificado.

Antes de comenzar la instalación, lea

cuidadosamente estas instrucciones de instalación y

el manual de instrucciones para asegurarse de que la

instalación se realice correctamente.

(Conserve estas instrucciones. Puede necesitarlas al

momento de realizar mantenimiento o trasladar esta

unidad)

RQT9746~Cover_mst.fm 1 ページ２０１３年７月３日　水曜日　午後３時１０分

RQT9746

Safety precautions

Unit

≥ To reduce the risk of fire, electric shock or product damage,

– Do not expose this unit to rain, moisture, dripping or

splashing.

– Do not place objects filled with liquids, such as vases, on

this unit.

– Use only the recommended accessories.

– Do not remove covers.

– Do not repair this unit by yourself. Refer servicing to

qualified service personnel.

– Do not let metal objects fall inside this unit.

– Do not place heavy items on this unit.

AC mains lead

≥ To reduce the risk of fire, electric shock or product damage,

– Ensure that the power supply voltage corresponds to the

voltage printed on this unit.

– Insert the mains plug fully into the socket outlet.

– Do not pull, bend, or place heavy items on the lead.

– Do not handle the plug with wet hands.

– Hold onto the mains plug body when disconnecting the

plug.

– Do not use a damaged mains plug or socket outlet.

≥ The mains plug is the disconnecting device.

Install this unit so that the mains plug can be unplugged from

the socket outlet immediately.

Button-type battery (Lithium battery)

≥ Risk of fire, explosion and burns. Do not recharge,

disassemble, heat above 60

C or incinerate.

≥ Keep the Button-Type battery out of the reach of children.

Never put Button-Type battery in mouth. If swallowed call

your doctor.

Unit

≥ This unit utilizes a laser. Use of controls or adjustments or

performance of procedures other than those specified herein

may result in hazardous radiation exposure.

≥ Do not place sources of naked flames, such as lighted

candles, on this unit.

≥ This unit may receive radio interference caused by mobile

telephones during use. If such interference occurs, please

increase separation between this unit and the mobile

telephone.

≥ This unit is intended for use in moderate climates.

Placement

≥ Place this unit on an even surface.

≥ To reduce the risk of fire, electric shock or product damage,

– Do not install or place this unit in a bookcase, built-in

cabinet or in another confined space. Ensure this unit is

well ventilated.

– Do not obstruct this unit’s ventilation openings with

newspapers, tablecloths, curtains, and similar items.

– Do not expose this unit to direct sunlight, high

temperatures, high humidity, and excessive vibration.

Button-type battery (Lithium battery)

≥ Danger of explosion if battery is incorrectly replaced.

Replace only with the type recommended by the

manufacturer.

≥ Insert with poles aligned.

≥ Mishandling of batteries can cause electrolyte leakage and

may cause a fire.

– Remove the battery if you do not intend to use the remote

control for a long period of time. Store in a cool, dark

place.

– Do not heat or expose to flame.

– Do not leave the battery(ies) in a car exposed to direct

sunlight for a long period of time with doors and windows

closed.

≥ When disposing the batteries, please contact your local

authorities or dealer and ask for the correct method of

disposal.

NORSK

Produkt

≥ For å redusere faren for brann, elektrisk støt eller skade på

apparatet:

– Utsett ikke produktet for regn, fukt, drypping eller sprut.

– Ikke plasser objekter som er fylt med væske, som vaser,

på apparatet.

– Bruk kun anbefalt tilbehør.

– Fjern ikke deksler.

– Reparer ikke denne enheten selv, overlat service til

kvalifisert servicepersonell.

Vekselstrømnett

≥ Nettstøpselet er trukket ut fra denne enheten.

Installer denne enheten slik at nettstøpselet umiddelbart kan

trekkes fra stikkontakten.

Produkt

≥ Dette produktet anvender en laser. Betjening av kontroller

eller justering eller andre inngrep enn de beskrevet i denne

bruksanvisning kan føre til farlig bestråling.

≥ Plasser ikke åpen ild, slik som levende lys, oppå apparatet.

≥ Dette apparatet er beregnet for bruk under moderate

klimaforhold.

Plassering

≥ For å redusere faren for brann, elektrisk støt eller skade på

apparatet:

– Ikke plasser apparatet i en bokhylle, et innebygget

kabinett eller et annet lukket sted. Pass på at produktet er

godt ventilert.

– Apparatets ventilasjonsåpninger må ikke dekkes til med

aviser, duker, gardiner eller lignende.

WARNING

CAUTION

ADVARSEL

FORSIKTIG

Product Identification Marking is located on the bottom of

the unit.

SC-HC38_EC~RQT9746-R.book 2 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

ENGLISH

Table of contents

Safety precautions............................................ 2

Accessories....................................................... 3

Control reference guide ................................... 4

Connections ...................................................... 5

Unit and media care.......................................... 5

Inserting media ................................................. 6

Bluetooth

operations ...................................... 7

Media playback operations.............................. 8

Listening to the radio ....................................... 9

Sound adjustment .......................................... 10

Clock and Timer.............................................. 10

Others .............................................................. 11

Troubleshooting.............................................. 11

About Bluetooth

............................................ 13

Playable media................................................ 14

Licenses .......................................................... 14

Specifications.................................................. 15

Attaching the unit to a wall (optional)........... 16

Accessories

About descriptions in these operating instructions

≥ Pages to be referred to are indicated as “l ±±”.

Check the supplied accessories before using this unit.

∏ 1 Remote control

(with a battery)

(N2QAYC000081)

∏ 1 AC mains lead

∏ 1 FM indoor

antenna

Wall mounting accessories

∏ 1 Safety holder

∏ 1 Screw

∏ 2 Wall mount

brackets



≥ Do not use AC mains lead with other equipment.

≥ Product numbers provided in these operating instructions are

correct as of December 2012. These may be subject to

change.

Information for Users on Collection and Disposal of Old Equipment and used Batteries

These symbols on the products, packaging, and/or accompanying documents mean that

used electrical and electronic products and batteries should not be mixed with general

household waste.

For proper treatment, recovery and recycling of old products and used batteries, please

take them to applicable collection points, in accordance with your national legislation and

the Directives 2002/96/EC and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to save valuable

resources and prevent any potential negative effects on human health and the

environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please

contact your local municipality, your waste disposal service or the point of sale where

you purchased the items.

Penalties may be applicable for incorrect disposal of this waste, in accordance with

national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or

supplier for further information.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these items,

please contact your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it

complies with the requirement set by the Directive for the chemical involved.

SC-HC38_EC~RQT9746-R.book 3 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

Control reference guide

1 Standby/on switch (Í/I) (Í)

Press to switch the unit from on to standby mode or vice

versa.

In standby mode, the unit is still consuming a small

amount of power.

2 Select the audio source

3 Basic playback control buttons

4 Enter setup menu

5 Enter the iPod/iPhone menu

Change displayed information

6 Open or close the sliding door

7 Adjust the volume (0 (min) to 50 (max))

8 Mute the sound

Mutes the sound. Press again to cancel. “MUTE”

is also cancelled when the volume is adjusted or

the unit is turned off.

9 Enter playback menu

10 Enter sound menu

11 Selection/OK

12 “IPOD_PORT” for iPod/iPhone/iPad (l 6)

USB port (l 6)

13 Dynamic Bass sound effect selector

14 Power on indicator

15 Display

16 Sliding door

17 Remote control signal sensor

Distance: Within approx. 7 m directly in front.

≥ To avoid interference, please do not put any objects in

front of signal sensor.

Unless otherwise indicated, operations are described

using the remote control.

On the remote control:

[iPod/USB]: “IPOD_DOCK” ,. “IPOD_PORT” / “USB”

[CD/RADIO]: “CD” ,. “FM”

[ ]: “BLUETOOTH”

On this unit:

“CD” ----. “FM” ----. “BLUETOOTH” ----. “IPOD_DOCK”

^-------------- “IPOD_PORT” / “USB” (----------------b

D.BASSSELECTOR

iPad

13673216

15 16

CD/

RADIO

iPod/

USB

Top view

∫ Before using for the first time

Remove the insulation sheet A.

∫ To replace a button-type battery

Battery type: CR2025 (Lithium battery)

≥ Set the button-type battery with its (i) mark facing upward.

≥ Keep the button-type battery out of reach of children to prevent swallowing.





SC-HC38_EC~RQT9746-R.book 4 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

ENGLISH

Connections



≥ These speakers do not have magnetic shielding. Do not place them near a television, personal computer or other devices easily

influenced by magnetism.

Unit and media care

Pull out the AC mains lead from the outlet before

maintenance.

∫ Clean this unit with a soft, dry cloth

≥ When dirt is heavy, wring a cloth moistened in water tightly to

wipe the dirt, and then wipe it with a dry cloth.

≥ Never use alcohol, paint thinner or benzine to clean this unit.

≥ Before using chemically treated cloth, carefully read the

instructions that came with the cloth.

∫ Maintenance of the lens

∫ Clean discs

Wipe with a damp cloth and then wipe dry.

∫ Disc handling precautions

≥ Handle discs by the edges to avoid inadvertent scratches or

fingerprints on the disc.

≥ Do not attach labels or stickers to discs.

≥ Do not use record cleaning sprays, benzine, thinner, static

electricity prevention liquids or any other solvent.

≥ Do not use the following discs:

– Discs with exposed adhesive from removed stickers or

labels (rented discs etc.).

– Discs that are badly warped or cracked.

– Irregularly shaped discs, such as heart shapes.

∫ To dispose or transfer this unit

The unit may keep the user settings information in the

unit. If you discard this unit either by disposal or transfer,

then follow the procedure to return all the settings to the

factory presets to delete the user settings.

(

11, “To return all settings to the factory preset”)

≥ The operation history may be recorded in the

memory of this unit.

≥ Tape the antenna to a wall or column in a position with the least amount of interference. (Use an FM outdoor antenna if radio

reception is poor.)

ョヮチモワヵ

ヘブ

モヤチリワ」

Connect the AC mains lead after all other connections are completed.

This unit consumes a small amount of AC power (l 15) even when turned off.

To household mains socket

AC mains lead (supplied)

≥ In the interest of power conservation, if you will not be using this unit for an extended period of time, unplug it from

the household mains socket.

FM indoor antenna

(supplied)

Adhesive tape

(not supplied)

≥ Clean the lens regularly to prevent malfunctions. Use a

blower to remove dust and a cotton swab if it is extremely

dirty.

≥ You cannot use a CD type lens cleaner.

≥ Do not leave the sliding door open for prolonged periods

of time. This will cause the lens to get dirty.

≥ Be careful not to touch the lens with your fingers.

Lens

DO DO NOT

SC-HC38_EC~RQT9746-R.book 5 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

Inserting media

*1: Refer to “Playable media” for compatible models. (l 14)

*2: When using the “IPOD_PORT” connection, do not connect

the following models to this unit:

– iPod classic, iPod [4th (colour display), and 5th (video)

generation]

Unexpected behaviour may occur.

*3: Connect using the dedicated USB cable (not supplied).

*4: Insert the USB device directly. Do not use any USB

extension cable.

*5: When using the “IPOD_DOCK” connection:

≥ Be sure to remove the iPod/iPhone from its case.

≥ Do not push or pull the dock manually.

≥ Make sure that the iPod/iPhone is fully inserted and its

back is resting against the cushion pad.

≥ Make sure to hold the dock when removing the iPod/

iPhone.

*6: Make sure to tilt the disc so as not to touch the sliding door.

≥ Do not open the sliding door manually.

≥ Make sure that the unit does not fall when inserting or

removing media.

≥ When moving this unit, be sure to remove all media and turn

this unit to standby mode.

≥ Before removing the USB device, select a source other than

“USB”.

Charging starts when an iPod*

/iPhone/iPad is

connected to this unit.

≥ During standby mode, charging will not start from the

“IPOD_PORT” connection, however it will start as usual from

the “IPOD_DOCK” connection.

– To charge from the “IPOD_PORT” connection, start the

charging before turning this unit to standby mode.



≥ Check the iPod/iPhone/iPad to see if the battery is fully

charged. (Once fully recharged, additional recharging will not

occur.)

≥ If this unit is switched to standby mode

“IPOD CHARGING” is shown on the unit’s display.

D.BASS

iPad

Select “IPOD_DOCK” as the source

Connect using the Lightning connector *1

Select “IPOD_PORT” as the source

“USB” is displayed when a compatible USB is

inserted.

Select “CD” as the source

*1, 2, 3

Charging an iPod/iPhone/iPad

SC-HC38_EC~RQT9746-R.book 6 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

ENGLISH

Bluetooth

operations

By using the Bluetooth

connection, you can listen to

the sound from the Bluetooth

audio device from this

unit wirelessly.

Preparation

≥ Turn on the Bluetooth

feature of the device and

place the device near this unit.

≥ If this unit is already connected to a Bluetooth

device, disconnect it.

1 Press [ ] to select “BLUETOOTH”.

≥ If “PAIRING” is indicated on the display, go to

step 3.

2 Press [PLAY MENU] to select “NEW DEV.” and

then press [OK].

{. “PAIRING” is indicated on the display.

3 Select “SC-HC38” from the Bluetooth

device’s

Bluetooth

menu.

4 Start play on the Bluetooth

device.



≥ Refer to the operating instructions of the Bluetooth

device

for details.

If prompted for the passkey, input “0000”.

≥ You can register up to 8 devices with this unit. If a 9th device

is paired, the device that has not been used for the longest

time will be replaced.

Preparation

≥ Turn on the Bluetooth

feature of the device and

place the device near this unit.

≥ If this unit is already connected to a Bluetooth

device, disconnect it.

1 Press [ ] to select “BLUETOOTH”.

{. “READY” is indicated on the display.

2 Select “SC-HC38” from the Bluetooth

device’s

Bluetooth

menu.

{. The name of the connected device is indicated on the

display for 2 seconds.

3 Start play on the Bluetooth

device.



≥ This unit can only be connected to one device at a time.

≥ When “BLUETOOTH” is selected as the source, this unit will

automatically try and connect to the last connected

Bluetooth

device. The Bluetooth

device will be

disconnected if a different audio source (e.g., [CD]) is

selected.

You can change the transmission speed to prioritize

transmission quality or sound quality.

Preparation

≥ Press [ ] to select “BLUETOOTH”.

≥ If a Bluetooth

device is already connected,

disconnect it.

1 Press [PLAY MENU] repeatedly to select

“LINK MODE”.

2 Press [3, 4] to select the mode and then press

[OK].

MODE 1: Emphasis on connectivity

MODE 2: Emphasis on sound quality



≥ The default setting is “MODE 1”.

If the sound input level of the Bluetooth

transmission

is too low, change the input level setting.

Preparation

≥ Connect a Bluetooth

device.

1 Press [PLAY MENU] repeatedly to select “INPUT

LEVEL”.

2 Press [3, 4] to select the level and then press

[OK].

“LEVEL 0” ,. “LEVEL i1” ,. “LEVEL i2”

^---------------------------------------------------------J



≥ Select “LEVEL 0” if the sound is distorted.

≥ The default setting is “LEVEL 0”.

1 While a Bluetooth

device is connected:

Press [PLAY MENU] to select “DISCONNECT?”.

2 Press [3, 4] to select “OK? YES” and then press

[OK].

Pairing Bluetooth

devices

Connecting a paired Bluetooth

device

Bluetooth

transmission mode

Bluetooth

input level

Disconnecting a Bluetooth

device

SC-HC38_EC~RQT9746-R.book 7 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

Media playback operations

The following marks indicate the availability of the

feature.

Preparation

≥ Turn the unit on.

≥ Insert the media (l 6) or connect the Bluetooth

device (l 7).

≥ Press [CD], [iPod/USB] or [ ] to select the audio

source.



≥ When using iPod/iPhone/iPad, the operation may vary

among those models.

∫ [CD], [USB], [Bluetooth] To display

information

Press [DISPLAY] repeatedly.



≥ To use this unit’s remote control with a Bluetooth

device, the

Bluetooth

device must support AVRCP (Audio Video

Remote Control Profile).

Depending on the device or the status of the device, some

operations may not work.

≥ Maximum number of displayable characters: approx. 30

≥

This unit supports ver. 1.0, 1.1 and 2.3 ID3 tags. Text data that

is not supported will not be displayed or shown differently.

≥ Album and track indication for MP3 files.

∫ [iPod] To navigate through the iPod/

iPhone menu

Open the Music App to use this feature with

iPod touch/iPhone.

–[3, 4]: To navigate menu items.

– [OK]: To go to the next menu.

– [iPod MENU]: To return to the previous menu.



≥ To view the operation, open the sliding door.

≥ Depending on the model (e.g., iPod nano 7th generation,

etc.), it may be necessary to select the album, artist, etc. on

the iPod/iPhone.

Select the playback mode.

1 Press [PLAY MENU] to select “PLAYMODE” or

“REPEAT”.

2 Press [3, 4] to select the setting and then press

[OK].



≥ When using an iPod/iPhone/iPad or Bluetooth

device, use

the setting on the device, if available.

≥ During random play, you cannot skip to the previous track.

≥ The mode is cancelled when you open the sliding door for

discs.

[CD]: CD audio in CD-DA format and a CD that

contains MP3 files (l 14)

[iPod]: Compatible iPod/iPhone/iPad (l 14)

[USB]: USB devices containing MP3 files (l 14)

[Bluetooth]: Connected Bluetooth

device (l 7)

Basic play ([CD], [iPod], [USB], [Bluetooth])

Play Press [1/;].

Stop Press [∫].

≥ [USB]: The position is memorised

and “RESUME” is displayed.

Pause Press [1/;].

Press again to restart play.

Skip Press [:/6] or [5/9]

to skip track.

[CD], [USB] Press [3] or [4] to

skip the MP3 album.

Search During play or pause

Press and hold [:/6] or

[5/9].

≥ [iPod]: Backwards search is only

within the current track.

“A _ _ _”: MP3 album number.

“T _ _ _”: MP3 track number.

≥ “ _ ” stands for the album or track number.

“”:

This indication is also used to refer to an album.

“”:

This indication is also used to refer to a track.

Playback modes ([CD], [USB])

PLAYMODE

OFF

PLAYMODE

Select to cancel the play mode

setting.

1-TRACK Only plays the selected track.

≥ “1”, “ ” is displayed.

(Skip to the desired track.)

1-ALBUM Only plays the selected MP3 album.

≥ “1”, “ ” is displayed.

RANDOM Plays the contents randomly.

≥ “RND” is displayed.

1-ALBUM

RANDOM

Plays the tracks in the selected

MP3 album randomly.

≥ Press [3] or [4] to select the MP3

album.

≥ “1”, “ ”, “RND” is displayed.

REPEAT

ON REPEAT Turn on repeat mode.

≥ “`” is displayed.

OFF

REPEAT

Turn off repeat mode.

SC-HC38_EC~RQT9746-R.book 8 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

ENGLISH

Preparation

≥ Turn the unit on.



≥ A station previously stored is overwritten when another

station is stored in the same channel preset.

1 Press [PLAY MENU] to select “A.PRESET”.

2 Press [3, 4] to select “LOWEST” or “CURRENT”

and then press [OK].

LOWEST:

CURRENT:

To begin auto preset with the current frequency.*

* To change the frequency, refer to “Manual tuning and

presetting”.

The tuner starts to preset all the stations it can

receive into the channels in ascending order.

Preparation

1 Press [PLAY MENU] repeatedly to select

“TUNEMODE”.

2 Press [3, 4] to select “PRESET” and then press

[OK].

Press [:/6] or [5/9] to select the channel.

∫ Manual tuning and presetting

Select a radio broadcast.

1 Press [PLAY MENU] repeatedly to select

“TUNEMODE”.

2 Press [3, 4] to select “MANUAL” and then press

[OK].

3 Press [:/6] or [5/9] to tune to the

required station.

≥ To start automatic tuning, press and hold [:/6],

[5/9] until the frequency starts scrolling. Tuning

stops when a station is found.

To preset the channel

4 While listening to the radio broadcast

Press [OK].

5 Press [3, 4] to select the channel and then press

[OK].

∫ To improve FM sound quality

1 While receiving FM broadcasts, press

[PLAY MENU] repeatedly to select “FM MODE”.

2 Press [3, 4] to select “MONO” and then press

[OK].

≥ This setting can be preset and memorised. To do so,

continue to step 4 of “Manual tuning and presetting”.



≥ Select “STEREO” in step 2 to return to stereo broadcasts.

≥ “MONO” is cancelled if the frequency is changed.

Press [DISPLAY] to display the text data.

≥ Each time you press the button:



≥ “STEREO” is displayed when this unit tunes to a stereo

broadcast.

≥ The unit can display the text data transmitted by the radio

data system (RDS) available in some areas. (RDS displays

may not be available if reception is poor.)

Listening to the radio

You can preset up to 30 channels.

≥ Make sure that the antenna is connected. (l 5)

≥ Press [RADIO] to select “FM”.

Presetting stations automatically

To begin auto preset with the lowest frequency

(FM 87.50).

Listening to a preset channel

≥ If “MONO” is selected, regardless of the type of signal this

unit is receiving, “FM MONO” is displayed. (l below)

∫ To display the current signal status

Press [PLAY MENU] to display “FM STATUS” and then

press [OK].

“FM ST”: The FM signal is in stereo.

“FM”: The FM signal is in monaural.

≥ “FM” is also displayed even if this unit is not tuned to a

station.

∫ To display RDS text data

“PS”: Programme service

“PTY”: Programme type

“FREQ”: Frequency display

SC-HC38_EC~RQT9746-R.book 9 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

Sound adjustment

The following sound effects can be added to the audio

output.

1 Press [SOUND] repeatedly to select the effect.

2 Press [3, 4] to select the setting and then press

[OK].

*1: This function can also be selected with the [D.BASS] button

on the unit.

≥ You may experience a reduction in sound quality when these

effects are used with some sources. If this occurs, turn the

sound effects off.

Clock and Timer

This is a 24-hour clock.

1 Press [SETUP] repeatedly to select “CLOCK”.

2 Press [3, 4] to set the time and then press [OK].



≥ To display the clock, press [SETUP] to select “CLOCK” and

then press [OK] once. The time is displayed for 10 seconds.

(During standby, press [DISPLAY] once.)

≥ The clock is reset when there is a power failure or when the

AC mains lead is removed.

≥ Reset the clock regularly to maintain accuracy.

You can set the timer so this unit turns on at a certain

time every day.

Preparation

Set the clock (l left).

∫ Setting the timer

1 Press [SETUP] repeatedly to select “TIMER ADJ”.

2 Press [3, 4] to set the starting time

(“ON TIME”) and then press [OK].

3 Press [3, 4] to set the finishing time

(“OFF TIME”) and then press [OK].

∫ Turn the timer on

1 Select the music source*

and set the desired

volume.

2 Press [SETUP] repeatedly to select “TIMER SET”.

3 Press [3, 4] to select “SET” and then press [OK].

≥ “F” is displayed.

≥ To turn the timer off, select “OFF”.

4 Press [Í] to turn the unit off.



≥ To display the timer settings, press [SETUP] repeatedly to

select “TIMER ADJ” and then press [OK] once.

The music source and volume will also be displayed if the

timer is turned on.

≥ During standby, if the timer is turned on, press [DISPLAY]

twice to display the settings.

≥ This unit can be used as normal after the timer is set,

however:

– Turn the unit to standby mode before the timer start time.

– Even if the audio source or the volume is changed, the

timer will still use the audio source and volume that was

set when the timer was turned on.

The sleep timer can turn the unit off after a set time.

1 Press [SETUP] to select “SLEEP”.

2 Press [3, 4] to set the time (in minutes) and then

press [OK].

“SLEEP 30” ,. “SLEEP 60” ,. “SLEEP 90” ,. “SLEEP 120”

^------------------------. OFF (Cancel) (------------------------J

≥ The remaining time is indicated on the unit’s display

except when other operations are performed.

≥ The play timer and sleep timer can be used together.

The sleep timer always has priority.

Direct-Vocal

Surround

(D.SURROUND)

“LEVEL 1”, “LEVEL 2” or “OFF”.

≥ The factory preset is “OFF”.

Preset EQ

(PRESET EQ)

“HEAVY” (heavy), “SOFT” (soft),

“CLEAR” (clear), “VOCAL”

(vocal) or “FLAT” (flat/off).

≥ The factory preset is “HEAVY”.

Bass (BASS) or

Treble (TREBLE)

Adjust the level (j4 to i4).

Dynamic Bass*

(D.BASS)

“ON D.BASS” or “OFF D.BASS”.

≥ The factory preset is “ON D.BASS”.

Setting the clock

Play timer

*1: “CD”, “USB”, “IPOD_PORT”, “IPOD_DOCK” and “FM” can

be set as the music source.

Sleep timer

SC-HC38_EC~RQT9746-R.book 10 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

ENGLISH

Others

As a factory preset, this unit will always turn off

automatically if there is no sound output and no

operation for approx. 30 minutes.

To cancel this function

1 Press [SETUP] repeatedly to select “AUTO OFF”.

2 Press [3, 4] to select “OFF” and then press [OK].



≥ To turn automatic standby on, select “ON” in step 2.

The brightness of this unit’s display can be changed.

1 Press [SETUP] repeatedly to select “DIMMER”.

2 Press [3, 4] to select “ON” and then press [OK].



≥ To cancel the dimmer, select “OFF” in step 2.

When other Panasonic equipment responds to the

supplied remote control, change the remote control

code.

1 Press [CD] to select “CD”.

2 While pressing and holding [SELECTOR] on the

unit, press and hold [CD/RADIO] on the remote

control until the unit's display shows “REMOTE 2”.

3 Press and hold [OK] and [CD/RADIO] on the

remote control for at least 4 seconds.



≥ To change the mode back to “REMOTE 1”, repeat the steps

above but replace the button pressed on the remote control

from [CD/RADIO] to [ ].

Troubleshooting

Before requesting service, make the following checks.

If you are in doubt about some of the check points, or if

the solutions indicated in the following guide do not

solve the problem, consult your dealer for instructions.

Humming heard during play.

≥ An AC mains lead or fluorescent light is near the cords. Keep

other appliances and cords away from this unit’s cables.

MP3 cannot be read.

≥ You may not be able to play MP3 if you have copied a

multi-session disc that has no data between sessions.

≥ When creating a multi-session disc, it is necessary to close the

session.

≥ The amount of data on the disc is too small. Set the amount of

data to above 5 MB.

Incorrect display or play will not start.

≥ Make sure that the disc is compatible with this unit. (l 14)

≥ There is moisture on the lens. Wait for about an hour and then try

again.

No response when [1/;] is pressed.

≥ Disconnect the USB device and then reconnect it. Alternatively,

turn the unit off and on again.

The USB drive or its contents cannot be read.

≥ The USB drive format or its contents is/are not compatible with the

unit (l 14).

≥ The USB host function of this product may not work with some

USB devices.

Slow operation of the USB flash drive.

≥ Large file size or high memory USB flash drive takes longer time

to read.

The elapsed time displayed is different from the

actual play time.

≥ Copy the data to another USB device or backup the data and

reformat the USB device.

Automatic standby

≥ This setting cannot be selected when “FM” is the source.

Display brightness

Changing the unit and remote

control code

To return all settings to the factory preset

When the following situations occur, reset the

memory:

≥ There is no response when buttons are pressed.

≥ You want to clear and reset the memory contents.

1 Disconnect the AC mains lead. (Wait for at least

3 minutes before proceeding to step 2.)

2 While pressing and holding down [Í/I] on the

unit, reconnect the AC mains lead.

≥ “--------” appears on the display.

3 Release [Í/I].



≥ All the settings are returned to the factory preset. You will

need to reset the memory items.

Common problems

Disc operations

USB operations

SC-HC38_EC~RQT9746-R.book 11 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

A beat sound or noise is heard while receiving

radio broadcast.

≥ Adjust the position of the antenna.

≥ Try to keep a certain amount of distance between the antenna and

AC mains lead.

≥ Try using an outdoor antenna if there are buildings or mountains

nearby.

≥ Switch the television or other audio players off or separate it from

this unit.

≥ Keep this unit away from mobile phones if the interference is

apparent.

Cannot charge or operate.

≥ Have you selected the appropriate selector?

Press [iPod] to select either “IPOD_DOCK” or “IPOD_PORT”.

≥ Check that the iPod/iPhone/iPad is connected properly. (l 6)

≥ The battery of the iPod/iPhone/iPad is depleted. Charge the iPod/

iPhone/iPad, and then operate again.

≥ Connect the iPod/iPhone/iPad again or try to restart the iPod/

iPhone/iPad.

≥ When this unit is in standby mode, charging will not start when

using the “IPOD_PORT” connection.

Turn this unit on and make sure the charging has started before

switching this unit to standby mode.

Pairing cannot be done.

≥ Check the Bluetooth

device condition.

The device cannot be connected.

≥ The pairing of the device was unsuccessful or the registration has

been replaced. Try pairing the device again. (l 7)

≥ This unit might be connected to a different device. Disconnect the

other device and try pairing the device again. (l 7)

The device is connected but audio cannot be heard

through this unit.

≥ For some built-in Bluetooth

devices, you have to set the audio

output to “SC-HC38” manually. Read the operating instructions for

the device for details.

The sound is interrupted.

≥ The device is out of the 10 m communication range. Bring the

Bluetooth

device closer to this unit.

≥ Remove any obstacle between this unit and the device.

≥ Other devices that use the 2.4 GHz frequency band (wireless

router, microwaves, cordless phones, etc.) are interfering. Bring

the Bluetooth

device closer to this unit and distance it from the

other devices.

≥ Select “MODE 1” for stable communication. (l 7)

The remote control doesn’t work properly.

≥ The remote control and this unit are using a different code.

(l 13, “REMOTE ”)

≥ Is the battery depleted or is the battery inserted incorrectly? (l 4)

The following messages or service numbers may

appear on the unit’s display.

“--:--”

≥ You plugged the AC mains lead in for the first time or there was a

power failure recently. Set the time (l 10).

“ADJUST CLOCK”

≥ Clock is not set. Adjust the clock accordingly.

“ADJUST TIMER”

≥ Play timer is not set. Adjust the play timer accordingly.

“AUTO OFF”

≥ The unit has been left unused for about 30 minutes and will shut

down within a minute. Press any button to cancel it.

“CANNOT SET”

≥ Select an audio source other than “BLUETOOTH”.

“CHECKING CONNECTION”

≥ The unit is checking the connected iPod/iPhone/iPad.

≥ If this display keeps appearing, make sure that the battery of the

iPod/iPhone/iPad is not depleted and that the iPod/iPhone/iPad is

turned on and connected correctly (l 6).

“ERROR”

≥ Incorrect operation is performed. Read the instructions and try

again.

“F” (“  ” stands for a number.)

≥ There is a problem with this unit.

Note down the displayed number, disconnect the AC mains lead

and consult your dealer.

“ILLEGAL OPEN”

≥ Sliding door is not in correct position. Turn the unit off and on

again. If this display appears again, consult the dealer.

“IPOD_DOCK OVER CURRENT ERROR”

“IPOD_PORT OVER CURRENT ERROR”

≥ The iPod/iPhone/iPad is drawing too much power. Disconnect the

iPod/iPhone/iPad and turn the unit off and on again.

≥ The USB device is drawing too much power. Switch to “CD”

mode, remove the USB and turn the unit off.

“NODEVICE”

≥ The iPod/iPhone/iPad device is not inserted correctly. Read the

instructions and try again (l 6).

≥ The battery of the iPod/iPhone/iPad is depleted. Charge the iPod/

iPhone/iPad and turn it on before connecting.

≥ The USB device is not inserted. Check the connection.

“NO DISC”

≥ Insert the disc to be played (l 6).

Radio

≥ Confirm the antenna is properly connected. (l 5)

iPod/iPhone/iPad operations

Bluetooth

Remote control

Messages

SC-HC38_EC~RQT9746-R.book 12 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

ENGLISH

“NO PLAY”

≥ A CD that is not in CD-DA or MP3 format is inserted. It cannot be

played.

≥ If there are more than 255 albums or folders (audio and

non-audio), some of the MP3 files in these albums may not be

read and played. Transfer these music albums to another USB.

Alternatively, reformat the USB device and save these music

albums prior to saving the other non-audio folders.

“NOT SUPPORTED”

≥ You have connected an iPod/iPhone/iPad that cannot be played

(l 14).

≥ If the iPod/iPhone/iPad is compatible, turn it on and connect it

correctly.

“READING”

≥ The unit is checking the CD information. After this display has

disappeared, start operating.

“REMOTE ” (“  ” stands for a number.)

≥ The remote control and this unit are using different codes. Change

the code on the remote control.

– When “REMOTE 1” is displayed, press and hold [OK] and [ ]

for more than 4 seconds.

– When “REMOTE 2” is displayed, press and hold [OK] and [CD/

RADIO] for more than 4 seconds.

About Bluetooth

∫ Frequency band used

≥ This unit uses the 2.4 GHz frequency band.

∫ Certification of this device

≥ This system conforms to frequency restrictions and

has received certification based on frequency laws.

Thus, a wireless permit is not necessary.

≥ The actions below are punishable by law in some

countries:

– Taking apart or modifying the unit.

– Removing specification indications.

∫ Restrictions of use

≥ Wireless transmission and/or usage with all

Bluetooth

equipped devices is not guaranteed.

≥ All devices must conform to standards set by

Bluetooth SIG, Inc.

≥ Depending on the specifications and settings of a

device, it can fail to connect or some operations can

be different.

≥ This system supports Bluetooth

security features.

But depending on the operating environment and/or

settings, this security is possibly not sufficient.

Transmit data wirelessly to this system with caution.

≥ This system cannot transmit data to a Bluetooth

device.

∫ Range of use

≥ Use this device at a maximum range of 10 m. The

range can decrease depending on the environment,

obstacles or interference.

∫ Interference from other devices

≥ This unit may not function properly and troubles such

as noise and sound jumps may arise due to radio

wave interference if this unit is located too close to

other Bluetooth

devices or the devices that use the

2.4 GHz band.

≥ This unit may not function properly if radio waves

from a nearby broadcasting station, etc. is too

strong.

∫ Intended usage

≥ This unit is for normal, general use only.

≥ Do not use this system near an equipment or in an

environment that is sensitive to radio frequency

interference (example: airports, hospitals,

laboratories, etc).

Panasonic bears no responsibility for data and/

or information that is compromised during a

wireless transmission.

SC-HC38_EC~RQT9746-R.book 13 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

Playable media

Compatible with “IPOD_DOCK” connection

(Using Lightning connector)

Compatible with “IPOD_PORT” connection

[Using dedicated USB cable (not supplied)]

(as of December 2012)



≥ Compatibility depends on the software version. Update your

iPod/iPhone/iPad to the latest software before using it with

this unit.

≥ Please be aware that Panasonic accepts no responsibility for

the loss of data and/or information.

≥ A disc with the CD Logo.

≥ This unit can play back discs that conform to the CD-DA

format.

≥ The unit may not be able to play some discs due to the

condition of the recording.

≥ This unit does not guarantee connection with all USB

devices.

≥ FAT12, FAT16 and FAT32 file systems are supported.

≥ This unit supports USB 2.0 full speed.

≥ This unit can support USB devices of up to 32 GB.

≥ Supported format: Files with the extension “.mp3” or “.MP3”.

≥ Compatible compression rate: Between 64 kbps and

320 kbps (stereo).

≥ Depending on how you create the MP3 files, they may not

play in the order you numbered them or may not play at all.

Creating MP3 files on a CD-R/RW

≥ Maximum number of tracks and albums: 999 tracks and 254

albums (Excluding Root folder).

≥ Disc formats: ISO9660 level 1 and level 2 (except for

extended formats).

≥ If the disc includes both MP3 and normal audio data

(CD-DA), the unit plays the type recorded in the inner part of

the disc.

≥ This unit cannot play files recorded using packet write.

Creating MP3 files on a USB device

≥ Maximum number of tracks and albums: 2500 tracks and 254

albums (Excluding Root folder).

≥ Only one memory card will be selected when connecting a

multiport USB card reader, typically the first memory card

inserted.

Licenses

Compatible iPod/iPhone/iPad

iPod touch (5th generation)

iPod nano (7th generation)

iPhone 5

iPod touch

1st, 2nd, 3rd, 4th, and 5th generation

iPod nano

2nd, 3rd, 4th, 5th, 6th, and 7th generation

iPhone 5 / iPhone 4S / iPhone 4 / iPhone 3GS /

iPhone 3G / iPhone

iPad (3rd, and 4th generation) / iPad 2 / iPad

iPad mini

Compatible CD

Compatible USB devices

Compatible MP3 files

“Made for iPod”, “Made for iPhone”, and “Made for iPad” mean

that an electronic accessory has been designed to connect

specifically to iPod, iPhone, or iPad, respectively, and has been

certified by the developer to meet Apple performance standards.

Apple is not responsible for the operation of this device or its

compliance with safety and regulatory standards.

Please note that the use of this accessory with iPod, iPhone, or

iPad may affect wireless performance.

iPad, iPhone, iPod, iPod classic, iPod nano, and iPod touch are

trademarks of Apple Inc., registered in the U.S. and other

countries.

The Bluetooth

word mark and logos are owned by the Bluetooth

SIG, Inc. and any use of such marks by Panasonic Corporation is

under license.

Other trademarks and trade names are those of their respective

owners.

MPEG Layer-3 audio coding technology licensed from

Fraunhofer IIS and Thomson.

SC-HC38_EC~RQT9746-R.book 14 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

ENGLISH

Specifications



≥ Specifications are subject to change without notice.

Mass and dimensions are approximate.

≥ Total harmonic distortion is measured by a digital spectrum

analyzer.

*1: When the iPod/iPhone/iPad is not charging and the dock is

closed.

*2: MPEG-1 Layer 3, MPEG-2 Layer 3

∫ GENERAL

Power consumption 34 W

Power consumption in standby mode*

Approx. 0.2 W

Power consumption in standby mode

(With the iPod dock open)

Approx. 0.5 W

Power supply

AC 220 V to 240 V, 50 Hz

Dimensions (WkHkD)

500 mmk204 mmk84 mm

(Depth without stand: 75 mm)

Mass Approx. 2.6 kg

Operating temperature range

0 oC to r40 oC

Operating humidity range

35 % to 80 % RH (no condensation)

∫ AMPLIFIER SECTION

Output power

RMS Output Power Stereo mode

Front Ch (both ch driven)

20 W per channel (6 ≠), 1 kHz, 10 % THD

Total RMS Stereo mode power

40 W

∫ TUNER SECTION

Preset Memory FM 30 stations

Frequency Modulation (FM)

Frequency range

87.50 MHz to 108.00 MHz (50 kHz step)

Antenna terminals

75 ≠ (unbalanced)

∫ DISC SECTION

Disc played (8 cm or 12 cm)

CD, CD-R/RW (CD-DA, MP3*

)

Pick up

Wavelength 790 nm (CD)

[NORSK]

Bølgelengde 790 nm (CD)

Laserstyrke Ingen farlig stråling sendes ut

(med sikkerhets-beskyttelse)

Audio output (Disc)

Number of channels

2 ch (FL, FR)

∫ SPEAKER SYSTEM SECTION

Type

1 way, 1 speaker system (Passive Radiator)

Speaker unit(s)

Full range

6.5 cm Cone typek1 per channel

Passive Radiator

8cmk2 per channel

Impedance 6 ≠

∫ TERMINAL SECTION

“IPOD_DOCK” connection

DC OUT 5 V 1.0 A MAX

“IPOD_PORT” connection

DC OUT 5 V 2.1 A MAX

USB Standard

USB 2.0 full speed

Media file format support

MP3 (¢.mp3)

USB device file system

FAT12, FAT16, FAT32

∫ BLUETOOTH SECTION

Bluetooth

system specification

V3.0

Wireless equipment classification

Class 2

Supported profiles

A2DP, AVRCP, GAVDP

Frequency band

2402 MHz to 2480 MHz

(Adaptive Frequency Hopping)

Driving distance 10 m Line of sight

SC-HC38_EC~RQT9746-R.book 15 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

Attaching the unit to a wall

(optional)

This unit can be wall mounted using the supplied wall

mount brackets, etc. Make sure that the screw used

and the wall are strong enough to support the weight of

at least 33 kg.

The screws and other items are not supplied as the

type and size will vary with each installation.

≥ Refer to step 3 of “Wall mount instructions” for details

about the required screws.

≥ Be sure to attach the fall prevention cord as a

secondary safety measure.

∫ Supplied accessories

≥ 1 Safety holder

≥ 1 Screw

≥ 2 Wall mount brackets

∫ Additionally required accessories

(commercially available)

≥ 4 Wall mount bracket fixing screws

≥ 1 Safety holder fixing screw

≥ 1 Fall prevention cord*

≥ 1 Screw eye

*1: Use a cord that is capable of supporting over 33 kg

(with a diameter of about 1.5 mm).

1 Detach the stand from the unit.

{. Unscrew the fixing screw (2 pieces) at the bottom of the

unit.

{. Gently pull the stand off the unit as illustrated.

≥ Keep the removed screws and stand in a safe place.

2 Measure and mark the position of the wall mount

brackets (Both sides).

{. Use figures below to identify the screwing positions.

The position to attach the wall mount brackets

Space required

Installation accessories

≥ Keep the safety holder out of reach of children to

prevent swallowing.

≥ Keep the screws out of reach of children to prevent

swallowing.

≥ Keep the wall mount brackets out of reach of children

to prevent swallowing.

Safety precautions

Professional installation is required.

The installation should never be done by any

other than a qualified installation specialist.

PANASONIC DISCLAIMS ANY PROPERTY

DAMAGE AND/OR SERIOUS INJURY,

INCLUDING DEATH RESULTING FROM

IMPROPER INSTALLATION OR INCORRECT

HANDLING.

≥ Be sure to install this unit as indicated within

these operating instructions.

Wall mount instructions

Before installation, turn the unit off and disconnect the

AC mains lead from the mains socket.

Bottom of the unit

Stand

Soft blanket or cloth

Fixing screw

202 mm

12.5 mm

300 mm

232 mm

700 mm

66 mm

202 mm

125 mm

143 mm

500 mm

118 mm

30 mm

SC-HC38_EC~RQT9746-R.book 16 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

ENGLISH

3 Attach the wall mount bracket to the wall with 2

screws (not supplied). (Both sides)

≥ Use a level to ensure both wall mount brackets are

level.

4 Fix the safety holder onto the unit with the screw

(supplied).

{. Screw tightening torque: 50 N0cm to 70 N0cm.

5 Attach the fall prevention cord (not supplied) to this

unit.

6 Hook the unit securely onto the wall mount

brackets with both hands.

≥ After hanging the unit, release your hands carefully to

confirm the unit sits securely on the wall.

7 Drive the safety holder fixing screw (not supplied)

to secure the safety holder onto the wall.

≥ Refer to step 3 for requirements before screwing.

8 Attach the fall prevention cord (not supplied) to the

wall.

≥ Make sure that the slack of the cord is minimal.

At least 30 mm

‰7.5 mm to

‰9.4 mm

‰4 mm

Wall mount bracket

Screw

(supplied)

Cord (not supplied)

≥ Connect the antenna and the AC mains lead to the unit

before hanging the unit onto the wall. (l 5)

Wall

Safety holder fixing screw

(not supplied)

Safety holder

Fixed to the wall

Cord (not supplied)

Screw eye

(not supplied)

Wall

SC-HC38_EC~RQT9746-R.book 17 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

Declaration of Conformity (DoC)

Hereby, “Panasonic Corporation” declares that this product is in

compliance with the essential requirements and other relevant

provisions of Directive 1999/5/EC.

Customers can download a copy of the original DoC to our R&TTE

products from our DoC server:

http://www.doc.panasonic.de

Contact to Authorised Representative: Panasonic Marketing Europe

GmbH,

Panasonic Testing Centre, Winsbergring 15, 22525 Hamburg,

Germany

This product is intended for general consumer. (Category 3)

Ελληνικά

Δήλωση συμμόρφωσης (DoC)

Με την παρούσα, η “Panasonic Corporation” δηλώνει ότι το προϊόν

αυτό είναι σύμφωνο με τις βασικές απαιτήσεις και άλλες σχετικές

διατάξεις της οδηγίας 1999/5/ΕC.

Οι πελάτες μπορούν να κατεβάσουν ένα αντίγραφο του πρωτοτύπου

DoC για τα R&TTE προϊόντα μας από τον DoC server μας:

http://www.doc.panasonic.de

Στοιχεία επικοινωνίας Eξουσιοδοτημένου Aντιπροσώπου: Panasonic

Marketing Europe GmbH,

Panasonic Testing Centre, Winsbergring 15, 22525 Hamburg,

Γερμανία

Αυτό το προϊόν προορίζεται για καταναλωτές. (Κατηγορία 3)

Português

Declaração de Conformidade (DoC)

Com o presente documento, a “Panasonic Corporation” declara que

este produto é conforme os requisitos específicos e demais

especificações referentes à Directriz 1999/5/EC.

Os clientes podem baixar uma cópia da declaração de conformidade

(DoC) para nossos produtos R&TTE do Server DoC:

http://www.doc.panasonic.de

Contacte o representante autorizado: Panasonic Marketing Europe

GmbH,

Panasonic Testing Centre, Winsbergring 15, 22525 Hamburg,

Alemanha

Este produto destina-se ao consumador geral. (Categoria 3)

Lietuviškai

Atitikties deklaracija (AD)

Bendrovė “Panasonic Corporation” patvirtina, kad šis gaminys

tenkina direktyvos 1999/5/EB esminius reikalavimus ir kitas

taikytinas nuostatas.

Mūsų R&TTE gaminių originalios atitikties deklaracijos kopiją klientai

gali atsisiųsti iš mūsų AD serverio:

http://www.doc.panasonic.de

Įgaliotojo atstovo adresas: “Panasonic Marketing Europe GmbH”,

Panasonic Testing Centre, Winsbergring 15, 22525 Hamburg,

Vokietija.

Šis gaminys skirtas bendrajam vartojimui. (3 kategorija.)

Slovensko

Izjava o skladnosti (DoC)

S pričujočo izjavo podjetje “Panasonic Corporation” izjavlja, da so

svoji izdelki skladni s poglavitnimi zahtevami in drugimi

odgovarjajočimi predpisi direktive 1999/5/ES.

Stranka lahko naloži izvod izvirnega DoC o naših izdelkih R&TTE s

strežnika DoC:

http://www.doc.panasonic.de

Pooblaščeni zastopnik: Panasonic Marketing Europe GmbH,

Panasonic Testing Centre, Winsbergring 15, 22525 Hamburg,

Nemčija

Izdelek je namenjen splošni uporabi. (Razred 3)

Slovensky

Vyhlásenie o zhode (DoC)

“Panasonic Corporation” týmto prehlasuje, že tento výrobok je v

zhode so základnými požiadavkami a ďalšími príslušnými

ustanoveniami smernice 1999/5/ES.

Zákazníci si môžu stiahnuť kópiu pôvodného DoC na naše R&TTE

výrobky z nášho servera DoC:

http://www.doc.panasonic.de

Kontakt na splnomocneného zástupcu: Panasonic Marketing Europe

GmbH,

Panasonic Testing Centre, Winsbergring 15, 22525 Hamburg,

Nemecko

Tento produkt je určený pre všeobecného spotrebiteľa. (Kategória 3)

Norsk

Samsvarserklæring (DoC)

“Panasonic Corporation” erklærer at utstyret er i samsvar med de

grunnleggende krav og øvrige relevante krav i direktiv 1999/5/EF.

Kundene kan laste ned en kopi av den originale

samsvarserklæringen (DoC) for vårt R&TTE utstyr fra vår DoC

server:

http://www.doc.panasonic.de

Kontakt vår autoriserte representant: Panasonic Marketing Europe

GmbH,

Panasonic Testing Centre, Winsbergring 15, 22525 Hamburg,

Tyskland

Utstyret er beregnet på den vanlige forbruker (klasse 3).

1177

SC-HC38_EC~RQT9746-R.book 18 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

ENGLISH

Eesti keel

Vastavusdeklaratsioon (DoC)

“Panasonic Corporation” kinnitab käesolevaga, et see toode on

vastavuses põhiliste nõuete ja muude direktiivi 1999/5/EÜ

asjakohaste sätetega.

Kliendid saavad koopia meie R&TTE toodetele kehtiva

originaalvastavusdeklaratsiooni koopia alla laadida meie

DoC-serverist:

http://www.doc.panasonic.de

Võtke ühendust volitatud esindajaga: Panasonic Marketing

Europe GmbH,

Panasonic Testing Centre, Winsbergring 15, 22525 Hamburg,

Germany

See toode on mõeldud tavakasutajale. (III kategooria)

Български

Декларация за съответствие (DoC)

“Panasonic Corporation” декларира, че този продукт съответства

на съществените изисквания и другите приложими разпоредби

на Директива 1999/5/EC.

Потребителите могат да свалят копие от оригиналните DoC към

нашите продуктите от типа R&TTE от сървъра, на който се

съхраняват DoC:

http://www.doc.panasonic.de

За контакт с оторизиран представител: Panasonic Marketing

Europe GmbH,

Panasonic Testing Centre, Winsbergring 15, 22525 Hamburg,

Германия

Този продукт е предназначен за обща употреба. (Категория 3)

Român

Declaraţie de Conformitate (DoC)

Prin prezenta, societatea “Panasonic Corporation” declară că

produsul este conform cu cerinţele esenţiale şi cu alte norme

corespunzătoare Directivei 1999/5/EC.

Clienţii pot descărca o copie a DoC-ului original al produselor

noastre R&TTE de la adressa noastră DoC din Internet:

http://www.doc.panasonic.de

Contact la Reprezentanţa autorizată: Panasonic Marketing Europe

GmbH,

Panasonic Testing Centre, Winsbergring 15, 22525 Hamburg,

Germania

Acest produs a fost proiectat pentru clientela generală. (Categoria 3)

Magyar

Megfelelőségi Nyilatkozat (DoC)

Ezennel a , “Panasonic Corporation” kijelenti, hogy a jelen termék

kielégíti az 1999/5/EK Irányelv létfontosságú követelményeit és más

vonatkozó rendelkezéseit.

A vásárlók letölthetik az R&TTE termékek eredeti DoC másolatát a

DoC szerverünkről:

http://www.doc.panasonic.de

Forduljon a hivatalos márkaképviselethez: Panasonic Marketing

Europe GmbH,

Panasonic Testing Centre, Winsbergring 15, 22525 Hamburg,

Németország

A terméket általános fogyasztóknak szánták. (3-as kategória)

Hrvatski

Deklaracija o podobnosti (DoC)

Ovime, “Panasonic Corporation” izjavljuje da je ovaj proizvod

udovoljava osnovnim zahtjevima i ostalim relevantnim uvjetima

Smjernice 1999/5/EC.

Kupci mogu preuzeti kopiju originalne DoC za naše R&TTE

proizvode s našeg DoC poslužitelja:

http://www.doc.panasonic.de

Kontakti u Europskoj uniji: Panasonic Marketing Europe GmbH,

Panasonic Testing Centre, Winsbergring 15, 22525 Hamburg,

Njemačka

Ovaj proizvod je namijenjen za opću potrošnju. (kategorija 3)

Latviski

Atbilstības deklarācija (DoC)

Kompānija “Panasonic Corporation” ar šo paziņo, ka šis

izstrādājums atbilst būtiskām prasībām un citām saistošām

Direktīvas 1999/5/EK prasībām.

Pircēji var lejupielādēt oriģinālo DoC kopiju mūsu R&TTE

izstrādājumos no mūsu DoC servera:

http://www.doc.panasonic.de

Lūdzam sazināties ar pilnvaroto parstāvi Panasonic

Marketing Europe GmbH,

Panasonic Testing Centre, Winsbergring 15, 22525

Hamburg, Germany

Šis izstrādājums ir paredzēts parastam patērētājam. (3. kategorija)

SC-HC38_EC~RQT9746-R.book 19 ページ２０１２年１２月２８日　金曜日　午後６時５３分

RQT9746

Zasady bezpieczeństwa

Urządzenie

≥ Aby ograniczyć niebezpieczeństwo pożaru, porażenia

prądem lub uszkodzenia urządzenia,

– Nie należy wystawiać urządzenia na działanie deszczu,

wilgoci, kapanie lub zachlapanie.

– Na urządzeniu nie należy ustawiać żadnych naczyń

zawierających płyny, takich jak wazony.

–Należy korzystać wyłącznie z zalecanych akcesoriów.

– Nie należy demontować obudowy urządzenia.

– Nie należy podejmować prób samodzielnej naprawy.

Naprawę urządzenia należy zlecić wykwalifikowanym

pracownikom serwisu.

–Należy uważać, aby do wnętrza urządzenia nie dostały

się metalowe przedmioty.

– Na urządzeniu nie wolno umieszczać żadnych ciężkich

przedmiotów.

Przewód zasilania

≥ Aby ograniczyć niebezpieczeństwo pożaru, porażenia

prądem lub uszkodzenia urządzenia,

–Należy się upewnić, że napięcie źródła zasilania

odpowiada napięciu podanemu na urządzeniu.

–Dokładnie podłączyć wtyczkę przewodu zasilającego do

gniazda ściennego.

– Nie wolno ciągnąć za przewód, zginać go ani kłaść na nim

ciężkich przedmiotów.

– Nie wolno dotykać wtyczki mokrymi rękami.

– Przy odłączaniu przewodu należy chwycić za wtyczkę.

– Nie wolno podłączać urządzenia do uszkodzonego

gniazda ściennego oraz gdy wtyczka przewodu

zasilającego jest uszkodzona.

≥ Wtyczka zasilania umożliwia odłączenie urządzenia.

Zainstaluj to urządzenie w taki sposób, aby mo

żliwe było

natychmiastowe odłączenie wtyczki zasilania od gniazda

zasilania.

Bateria guzikowa (Bateria litowa)

≥ Niebezpieczeństwo pożaru, wybuchu i poparzenia. Nie ładuj,

rozbieraj, podgrzewaj powyżej 60 xC lub spalaj.

≥ Trzymaj baterię guzikową z dala od dzieci. Nigdy nie wkładaj

baterii guzikowej do ust. Jeżeli zostanie ona połknięta,

skontaktuj się z lekarzem.

Urządzenie

≥ W tym urządzeniu znajduje się laser. Wykonywanie regulacji

innych niż opisane lub postępowanie w sposób

nieprzewidziany w instrukcji obsługi grozi niebezpiecznym

naświetleniem promieniami lasera.

≥ Nie należy umieszczać na urządzeniu źródeł otwartego

ognia, takich jak zapalone świece.

≥ To ur ządzenie może odbierać zakłócenia wywołane użyciem

telefonu komórkowego. Jeżeli takie zakłócenia wystąpią,

wskazane jest zwiększenie odległości pomiędzy

urządzeniem a telefonem komórkowym.

≥ Urządzenie jest przeznaczone do używania w klimacie

umiarkowanym.

Wybór miejsca

≥ Urządzenie należy ustawić na równej powierzchni.

≥ Aby ograniczyć niebezpieczeństwo pożaru, porażenia

prądem lub uszkodzenia urządzenia,

– Niniejszego urządzenia nie należy instalować lub

umieszczać w szafce na książki, zabudowanej szafce lub

innej ograniczonej przestrzeni, w celu zapewnienia dobrej

wentylacji.

– Nie należy zasłaniać otworów wentylacyjnych urządzenia

gazetami, obrusami, zasłonami i podobnymi

przedmiotami.

–Urządzenie należy chronić przed bezpośrednim

działaniem promieni słonecznych, wysoką temperaturą,

wysoką wilgotnością oraz nadmiernymi drganiami.

Bateria guzikowa (Bateria litowa)

≥ Istnieje niebezpieczeństwo wybuchu w przypadku, gdy

baterie zostaną nieprawidłowo włożone. Baterie należy

wymieniać wyłącznie na baterie typu zalecanego przez

producenta.

≥ Wkładając, pamiętaj o zachowaniu prawidłowej

biegunowości.

≥ Nieprawidłowe obchodzenie się z bateriami może prowadzić

do wycieku elektrolitu i może być także przyczyną pożaru.

– Baterię należy wyjąć, jeżeli pilot nie będzie używany przez

dłuższy czas. Należy ją przechowywać w chłodnym,

ciemnym miejscu.

– Nie ogrzewaj i nie wrzucaj do ognia.

– Nie należy pozostawiać baterii przez dłuższy czas w

samochodzie z zamkniętymi drzwiami i oknami

wystawionym na bezpośrednie działanie promieni

sł

onecznych.

≥ W przypadku utylizacji baterii, należy się skontaktować z

lokalnymi władzami lub ze sprzedawcą celem uzyskania

informacji o prawidłowym sposobie postępowania.

OSTRZEËENIE UWAGA

Oznaczenia identyfikacyjne produktu znajdują się na spodzie urządzenia.

Deklaracja zgodności

Niniejszym “Panasonic Corporation” deklaruje, że ten produkt jest zgodny z istotnymi wymaganiami i innymi odnośnymi

postanowieniami dyrektywy 1999/5/WE.

Klienci mogą pobrać oryginalną deklarację zgodności naszych produktów z serwera deklaracji zgodności:

http://www.doc.panasonic.de

Kontakt się z autoryzowanym przedstawicielem: Panasonic Marketing Europe GmbH,

Panasonic Testing Centre, Winsbergring 15, 22525 Hamburg, Niemcy

Ten produkt jest przeznaczony dla użytkownika ogólnego. (Kategoria 3)

1177

SC-HC38_EC~RQT9746-R.book 20 ページ２０１２年１２月２８日　金曜日　午後６時５３分

Strona jest ładowana ...

Panasonic SC-HC38 Operating Instructions Manual

Marka: Panasonic

Model: SC-HC38

Typ: Operating Instructions Manual

ściągnij PDF

raport

w innych językach

español: Panasonic SC-HC38
slovenčina: Panasonic SC-HC38
English: Panasonic SC-HC38

Panasonic SC-HC38 Operating Instructions Manual

Panasonic SC-HC38 Operating Instructions Manual

w innych językach

Powiązane dokumenty

Inne dokumenty