Sierra QuadraTherm 640i/780i Modbus Instrukcja obsługi

QuadraTherm

®

640i/780i Modbus

Instruction Manual

Modbus Interface Specification for Models: 640i and 780i

Thermal Mass Flow Meters

Part Number: IM640i/780i-Modbus Rev. V2

June 2019

GLOBAL SUPPORT LOCATIONS: WE ARE HERE TO HELP!

CORPORATE HEADQUARTERS

5 Harris Court, Building L Monterey, CA 93940

Phone (831) 373-0200 (800) 866-0200 Fax (831) 373-4402

www.sierrainstruments.com

EUROPE HEADQUARTERS

Bijlmansweid 2 1934RE Egmond aan den Hoef

The Netherlands

Phone +31 72 5071400 Fax +31 72 5071401

ASIA HEADQUARTERS

Second Floor Building 5, Senpu Industrial Park

25 Hangdu Road Hangtou Town

Pu Dong New District, Shanghai, P.R. China

Postal Code 201316

Phone: + 8621 5879 8521 Fax: +8621 5879 8586

IMPORTANT CUSTOMER NOTICE- OXYGEN SERVICE

Sierra Instruments, Inc. is not liable for any damage or personal injury, whatsoever, resulting from the use of Sierra Instruments

standard mass flow meters for oxygen gas. You are responsible for determining if this mass flow meter is appropriate for your

oxygen application. You are responsible for cleaning the mass flow meter to the degree required for your oxygen flow

application.

No part of this publication may be copied, distributed, transmitted, transcribed, or stored in a retrieval system. No part of this publication

may be translated into any human or computer language, in any form or by any means, electronic, mechanical, manual, or otherwise,

or disclosed to third parties without the express written permission of Sierra Instruments. The information contained in this manual is

subject to change without notice.

TRADEMARKS

QuadraTherm

®

is a trademark of Sierra Instruments, Inc. Other product and company names listed in this manual are trademarks or trade

names of their respective manufacturers.

Warnings and Cautions

Warning!

Agency approval for hazardous location installations varies between flow meter models. Consult the flow meter

nameplate for specific flow meter approvals before any hazardous location installation.

Warning!

Hot tapping must be performed by a trained professional. U.S. regulations often require a hot tap permit. The

manufacturer of the hot tap equipment and/or the contractor performing the hot tap is responsible for providing proof of such a

permit.

Warning!

All wiring procedures must be performed with the power off.

Warning!

To avoid potential electric shock, follow National Electric Code safety practices or your local code when wiring this unit

to a power source and to peripheral devices. Failure to do so could result in injury or death. All AC power connections must be in

accordance with published CE directives.

Warning!

Do not power the flow meter with the sensor remote (if applicable) wires disconnected. This could cause over-

heating of the sensors and/or damage to the electronics.

Warning!

Before attempting any flow meter repair, verify that the line is de-pressurized.

Warning!

Always remove main power before disassembling any part of the mass flow meter.

Caution!

Before making adjustments to the device, verify the flow meter is not actively monitoring or reporting to any master control

system. Adjustments to the electronics will cause direct changes to flow control settings.

Caution!

All flow meter connections, isolation valves and fittings for hot tapping must have the same or higher pressure rating

as the main pipeline.

Caution!

Changing the length of cables or interchanging sensors or sensor wiring will affect the accuracy of the flow meter.

You cannot add or subtract wire length without returning the meter to the factory for re-calibration.

Caution!

When using toxic or corrosive gases, purge the line with inert gas for a minimum of four hours at full gas flow before

installing the meter.

Caution!

The AC wire insulation temperature rating must meet or exceed 80°C (176°F).

Caution!

Printed circuit boards are sensitive to electrostatic discharge. To avoid damaging the board, follow these

precautions to minimize the risk of damage:

• before handling the assembly, discharge your body by touching a grounded, metal object

• handle all cards by their edges unless otherwise required

• when possible, use grounded electrostatic discharge wrist straps when handling sensitive components

Note and Safety Information

We use caution and warning statements throughout this book to draw

your

attention to important information.

Warning!

Caution!

This statement appears with information that

is important to protect people and equipment

from damage. Pay very close attention to all

warnings that apply to your application.

This statement appears with information that is

important for protecting your equipment and

performance. Read and follow all cautions that

apply to your application.

Receipt of System Components

When receiving a Sierra mass flow meter, carefully check the outside

packing

carton

for damage incurred in shipment. If the carton is damaged, notify the local carrier

and submit a report to the factory or distributor. Remove the packing slip and

check that all ordered components are present. Make sure any spare parts or

accessories are not

discarded with the packing material. Do not return any

equipment to

the factory without first contacting Sierra’s Customer Service

Department

.

Technical Assistance

If you encounter a problem with your flow meter, review the configuration

information for each step of the installation, operation, and

setup procedures.

Verify that your settings and adjustments are consistent with factory

recommendations. Installation and troubleshooting information can be found in

the QuadraTherm

®

640i/780i Series product manual.

If the problem persists after following the troubleshooting procedures

outlined in the

640i or 780i product manuals, contact Sierra Instruments by fax or by e-mail

(see

inside front cover). For urgent phone support, you may call (800)

866-0200 or

(831) 373-0200 between 8:00 a.m. and 5:00 p.m. PST. In

Europe, contact Sierra

Instruments Europe at +31 20 6145810. In the Asia-Pacific region, contact Sierra

Instruments Asia at +

86-21-58798521.

When contacting Technical Support, make

sure to include this information:

•

The flow range, serial number, and Sierra order number (all

marked on the meter nameplate)

•

The software version (visible at start up)

•

The problem you are encountering and any corrective action

taken

•

Application information (gas, pressure, temperature and piping

configuration)

5 
 
   
Table of Contents 
 
Chapter 1- Introduction .......................................................................................................................... 6 
Chapter 2 - Electrical Connections ........................................................................................................ 7 
RS-485 Connection ................................................................................................................7 
General 2-Wire Topology RS-485 Network ..........................................................................9 
Chapter 3 - Communicating ................................................................................................................. 11 
Data Format Type for Various Registers ..............................................................................11 
Modbus Registers Overview ................................................................................................11 
Registers Explained ..............................................................................................................14 
Register Descriptions............................................................................................................14 
Chapter 4 - Bootloader ......................................................................................................................... 23 
Introduction ..........................................................................................................................23 
Getting Started ......................................................................................................................23 
Load Firmware .....................................................................................................................24 
Setup Firmware ....................................................................................................................26 
Quit .......................................................................................................................................28 
Troubleshooting ....................................................................................................................28 
 
 
 
 
 
 
 
 
 

6

Chapter 1- Introduction

Modbus is a serial communications protocol first published by Modicon in 1979 for use with

its programmable logic controllers (PLCs). It’s simple and robust, royalty free and it has since

become a de facto standard communication protocol, and it is now a commonly available

means of connecting industrial electronic devices in the USA.

Modbus allows for communication between many devices (nodes) connected to the same

network. Modbus is often used to connect a supervisory computer with a remote terminal unit

(RTU) in supervisory control and data acquisition (SCADA) systems. It supports many data

types, Including:

• Floating point IEEE 754 (Real)

• 32-bit integer

• 8-bit ASCII data

• 16-bit integer

• Mixed data types

• Bit fields in integers

• Multipliers to change data to/from integer. 10, 100, 1000, 256 ...

The Modbus interface discussed in this manual is an option for Sierra Instruments’

QuadraTherm 640i/780i four-sensor thermal mass flow meter. The interface makes it possible

to connect the QuadraTherm to a Modbus network and remotely operate it.

For more information about Modbus, visit their website at http://www.Modbus.org/.

Note

To fully understand the QuadraTherm and its functions it is advised to also

read the QuadraTherm instruction manual.

7

Chapter 2 - Electrical Connections

All electrical connections are made on the terminal board inside the QuadraTherm enclosure.

Instrument Power Connection

Power supply requirements for the QuadraTherm are the following:

Voltage: 24 VDC +/- 10%,

Amperage: 1.1 A

Modbus RS-485 Connection

Caution

The QuadraTherm is equipped with an optical isolated RS-485 interface.

Grounding the Modbus shield (16) would defeat this.

DC Power -

DC Power +

8

Connecting the RS-485 to Your QuadraTherm

1. Connect your 2-wire RS-485 A (-) to the A terminal and the 2-wire RS-485 B (+) to

the B terminal. Occasionally you may find a Modbus device from another manufacter

labeled A+ and B-, in that case the A and B terminals need to be swapped.

2. Connect the RS-485 common (C or sheild) to the Modbus Sheild on terminal 16.

3. The meter’s Modbus Address, Baud Rate, and Parity are set using the bootloader, see

Chapter 4. You should do this before connecting to the full RS485 network.

1. Cabling Summary

Use a 24 AWG shielded twisted pair cable, with low capacitance, 120Ω impedance

like Belden 9841.

2. Never put the Modbus wires in the same conduit as AC power. Ideally DC power

wires should be run in separate conduit if possible, to prevent interference issues.

3. Both ends of the RS485 network cable should have 120 Ω resistors to prevent

reflections. Before the network is running you should be able to verify this with a

simple DMM. You should measure about 60Ω total. (Two 120Ω resistors in parallel)

4. Terminal labeled A & B will be connected to the twisted wire pair in the center of the

cable.

5. The cable shield wire needs be connected terminal 16. It’s better if it is not connected

to Earth ground. However, some other Modbus devices on your network may already

Earth grounded this shield. This is still acceptable, but it best that this device is near

the master.

6. Wires between Modbus devices need to be wired in a daisy-chain pattern. They

should never be wired with separate home-runs back to the master in a Star pattern.

When daisy chaining the Modbus A/B wires you should either twist the wires

together and solder or use a crimp ferrule, this would still allow the bus to be

connected even if the meter A/B wires were disconnected.

7. Keep the wires as short as possible inside the enclosure and maintain the A/B wire

twist as much as possible.

8. The meter enclosure must always be Earth grounded. This prevents Electrostatic and

Electromagnetic noise from interfering and the meter’s microprocessor and with the

Modbus data. In addition, it also provides for safety, EMI, RFI, and ESD protection.

RS485 A

RS485 B

RS485 common

9

Both the main and remote (if E4 option ordered) enclosures should be connected to

earth ground, see below for more details.

A. External Earthing: The external earthing connections are located on the boss on

the outside of both the main housing and remote housing (E4 option if ordered)

and consist of an 18-8SS pan head Phillips screw (10-24 UNC-2B thread) and a

serrated tooth #10 ring terminal for 16-14 AWG wire.

B. Internal Earthing: The internal earthing connection is located in the main housing

terminal side and consist of an 18-8SS pan head Phillips screw (10-24 UNC-2B

thread) and a serrated tooth #10 ring terminal for 16-14 AWG wire.

General 2-Wire Topology RS-485 Network

Modbus-RTU uses a common 2-wire RS-485 network for its physical layer. RS-485 is simple

and robust. For short wire runs and lower baud rates it is very forgiving.

RS-485 only specifies electrical characteristics of the Master and the Slave. It does not

specify or recommend any communications protocol or Data Link layer. Unlike proprietary

RS-485 based field buses; Modbus uses the same Data Link layer used by PCs. This allows

you to be able to use cheap USB to RS485 adapters as a Modbus master.

The RS-485 bus needs to be wired in a daisy chain pattern between devices. If stub wires are

necessary, they cannot be more the 10 cm long.

10

Cable

It is recommended to use shielded twisted pair type of cable (reduces radiated and received

EMI). Use a 24 AWG shielded twisted pair cable, with low capacitance like Belden 9841.

Terminator

Reflections in a transmission line can cause communication errors. To minimize the reflection

it is required to place 120Ω terminator resistors at both ends of the cable. Never place a

terminator resistor in the middle of the network. Some Gateways, PLC, and other types of

Modbus masters have terminator resistors built-in. If so, do not add another one. Using an

Oscilloscope you can see what a reflection looks like, and how it can confuse the data:

Not terminated Properly Terminated

Line Polarization

RS-485 has 3 voltages levels, “1” , “0” , and idle. In noisy environments it may be necessary

to polarize the lines to ensure that the idle stays low so all the slave devices on the network

stay in the listen mode, waiting for their address to be called.

Most master devices have this already built in. In very noisy cases you may need make circuit

do this. However, a commercially available isolated RS485 repeater in the middle of your

wire run will “clean up” the signals and polarize the idle voltage. This is also very useful for

long wire runs. A repeater also allows you to add another 32 devices.

Shield Wire Grounding

We use a RS485 chip that has 1,500 Volts of isolation. For electrical noise it’s best to keep

the shield wire isolated from Earth ground and only connect it to terminal 16 and the signal

ground at the Master.

Occasionally, you may have no choice but share the Modbus network with a device that has a

non-isolated RS485 chip. Usually you can get by with this. It is best for this non-isolated

device to be the first device on the network. If you have trouble, you may need to use an

isolated RS485 repeater to separate it from the rest of the network.

11

Chapter 3 - Communicating

Once the QuadraTherm is wired to the network and powered up, it is time to communicate

with it. The factory default settings for the Modbus interface are the following:

• ID code = 1

• Baud rate = 19200

• Parity = Even

• Number of bits = 8

• Stop bit = 1

• Delay between receiving and transmitting = 8 ms

The above Modbus settings are the factory defaults and can be changed. The changes can be

done through the boot loader.

Data Format Type for Various Registers

The following are data format various registers available:

• 32 bit real: IEEE 754 floating point, low word first

• 16 bits integer: unsigned integer values

• 16 bits ASCII: ASCII encoded characters, high word = 1

st

character (0x4944 = “ID”)

Modbus Registers Overview

PDU

Address

Register

Description

Read/

Write

Type

No.

registers*

$00

40001

Actual flow - low word

R

32 bits real

2

$01

40002

Actual flow - high word

R

$02

40003

Actual temp - low word

R

32 bits real

2

$03

40004

Actual temp - high word

R

$04

40005

Actual pressure - low word

R

32 bits real

2

$05

40006

Actual pressure - high word

R

$06

40007

Actual total - low word

R

32 bits real

2

$07

40008

Actual total - high word

R

$08

40009

Alarm status

R

integer

1

$09

40010

Gas name

R

16 bits ASCII

8

~

$10

40017

$11

40018

Gas index

R/W

integer

1

$12

40019

Flow units

R

16 bits ASCII

4

~

$15

40022

$16

40023

Flow unit - index

R/W

integer

1

$17

40024

User full scale – low word

R/W

32 bits real

2

$18

40025

User full scale – high word

R/W

$19

40026

Totalizer units

R

16 bits ASCII

2

$1A

40027

$1B

40028

Totalizer unit - index

R

integer

1

12

$1C

40029

Temperature units

R

16 bits ASCII

1

$1D

40030

Temperature unit - index

R/W

integer

1

$1E

40031

Pressure units

R

16 bits ASCII

4

~

$21

40034

$22

40035

Pressure unit - index

R/W

integer

1

$23

40036

Standard Temperature - low word

R/W

32 bits real

2

$24

40037

Standard Temperature - high word

R/W

$25

40038

Standard Temperature - index

R/W

integer

1

$26

40039

Standard pressure - low word

R/W

32 bits real

2

$27

40040

Standard pressure - high word

R/W

$28

40041

Standard pressure - index

R/W

integer

1

$29

40042

Normal Temperature - low word

R/W

32 bits real

2

$2A

40043

Normal Temperature - high word

R/W

$2B

40044

Normal Temperature - index

R/W

integer

1

$2C

40045

Normal pressure - low word

R/W

32 bits real

2

$2D

40046

Normal pressure - high word

R/W

$2E

40047

Normal pressure - index

R/W

integer

1

$2F

40048

Adjust DAC for flow – 4mA

R/W

integer

1

$30

40049

Adjust DAC for flow – 20mA

R/W

integer

1

$31

40050

Adjust DAC for Temperature – 4mA

R/W

integer

1

$32

40051

Adjust DAC for Temperature – 20mA

R/W

integer

1

$33

40052

Adjust DAC for pressure – 4mA

R/W

integer

1

$34

40053

Adjust DAC for pressure – 20mA

R/W

integer

1

$35

40054

Temperature 4mA value – low word

R/W

32 bits real

2

$36

40055

Temperature 4mA value – high word

R/W

$37

40056

Temperature 20mA value – low word

R/W

32 bits real

2

$38

40057

Temperature 20mA value – high word

R/W

$39

40058

Pressure 4mA value – low word

R/W

32 bits real

2

$3A

40059

Pressure 4mA value – high word

R/W

$3B

40060

Pressure 20mA value – low word

R/W

32 bits real

2

$3C

40061

Pressure 20mA value – high word

R/W

$3D

40062

Alarm active

R/W

integer

1

$3E

40063

Alarm mode

R/W

integer

1

$3F

40064

Low alarm flow trig – low word

R/W

32 bits real

2

$40

40065

Low alarm flow trig – high word

R/W

$41

40066

High alarm flow trig – low word

R/W

32 bits real

2

$42

40067

High alarm flow trig – high word

R/W

$43

40068

Low alarm temp trig – low word

R/W

32 bits real

2

$44

40069

Low alarm temp trig – high word

R/W

$45

40070

High alarm temp trig – low word

R/W

32 bits real

2

$46

40071

High alarm temp trig – high word

R/W

$47

40072

Low alarm pressure trig – low word

R/W

32 bits real

2

$48

40073

Low alarm pressure trig – high word

R/W

$49

40074

High alarm pressure trig – low word

R/W

32 bits real

2

$4A

40075

High alarm pressure trig – high word

R/W

$4B

40076

Low alarm total trig – low word

R/W

32 bits real

2

$4C

40077

Low alarm total trig – high word

R/W

$4D

40078

High alarm total trig – low word

R/W

32 bits real

2

$4E

40079

High alarm total trig – high word

R/W

$4F

40080

Pipe diameter – low word

R/W

32 bits real

2

$50

40081

Pipe diameter – high word

R/W

$51

40082

Pipe roughness

R/W

integer

1

13

$52

40083

Pipe diameter units - index

R/W

integer

1

$53

40084

Flow correction – low word

R/W

32 bits real

2

$54

40085

Flow correction – high word

R/W

$55

40086

Totalizer enable

R/W

integer

1

$56

40087

Totalizer buck – low word

R/W

32 bits real

2

$57

40088

Totalizer buck – high word

R/W

$58

40089

Totalizer pulse width

R/W

integer

1

$59

40090

Totalizer reset

R/W

integer

1

$5A

40091

Password

R/W

integer

1

$5B

40092

Standard temperature units

R

16 bits ASCII

1

$5C

40093

Normal temperature units

R

16 bits ASCII

1

$5D

40094

Standard pressure units

R

16 bits ASCII

4

~

$60

40097

$61

40098

Normal pressure units

R

16 bits ASCII

4

~

$64

40101

$65

40102

Pipe diameter units

R

16 bits ASCII

2

$66

40103

$67

40104

Pipe roughness description

R

16 bits ASCII

5

~

$6B

40108

$6C

40109

Alarm status

R

16 bits ASCII

2

$6D

40110

$6E

40111

Alarm active

R

16 bits ASCII

2

$6F

40112

$70

40113

Alarm mode

R

16 bits ASCII

3

~

$72

40115

$73

40116

Serial number

R

16 bits ASCII

4

~

$76

40119

$77

40120

Firmware version

R

16 bits ASCII

4

~

$7A

40123

$7B

40124

Calibration date

R

16 bits ASCII

5

~

$7F

40128

$80

40129

PCA version

R

16 bits ASCII

3

~

$82

40131

* Note: Exceeding the numbers of suggested registers will raise an exception code.

14

Registers Explained

The registers are divided into two groups. The first group (40001 – 40009) represents the

dynamic data and changes the most of the two groups. The second group (40010 – 40131)

contains the settings of the QuadraTherm meter.

Register Descriptions

40001: Actual Flow

The actual flow as measured by the instrument.

40003: Actual Temperature

The actual gas temperature as measured by the instrument.

40005: Actual Pressure

The actual pressure as measured by the instrument (if applicable).

40009: Alarm Status

Value representing the status of the alarm:

0 – Alarm of Off/Inactive

1 – Alarm is On/Active

40010 - 40017: Gas Name

40010-40017 Registers are an ASCII string showing the name of the currently selected gas.

Use register 40018 to select a different gas.

40018: Gas Index

Value indicates which gas is selected on the instrument. The value can range between 0 and 3.

0 is always Air and 1-3 are the alternate gases.

40019: Flow Units

ASCII string shows the currently selected flow engineering unit on the instrument. Use

Register 40023 to select a different flow unit

Note

To fully understand the registers and their functions, we suggest you also

read the QuadraTherm instruction manual.

15

40023: Flow Unit Index

Value shows which flow unit is selected on the instrument. The value can range between 0

and 49:

• 0 – SCFS

• 1 – SCFM

• 2 – SCFH

• 3 – SCFD

• 4 – SCFY

• 5 – NCFS

• 6 – NCFM

• 7 – NCFH

• 8 – NCFD

• 9 – NCFY

• 10 – SM3/Sec

• 11 – SM3/Min

• 12 – SM3/Hour

• 13 – SM3/Day

• 14 – SM3/Year

• 15 – NM3/Sec

• 16 – NM3/Min

• 17 – NM3/Hour

• 18 – NM3/Day

• 19 – NM3/Year

• 20 – SLPS

• 21 – SLPM

• 22 – SLPH

• 23 – SLPD

• 24 – SLPY

• 25 – NLPS

• 26 – NLPM

• 27 – NLPH

• 28 – NLPD

• 29 – NLPY

• 30 – Lbs/Sec

• 31 – Lbs/Min

• 32 – Lbs/Hour

• 33 –Lbs/Day

• 34 – Lbs/Year

• 35 – Kg/Sec

• 36 – Kg/Min

• 37 – Kg/Hour

• 38 –Kg/Day

• 39 –Kg/Year

• 40 – SFPS

• 41 – SFPM

• 42 – SFPH

• 43 – SFPD

• 44 – SFPY

• 45 – SMPS

• 46 – SMPM

• 47 – SMPH

• 48 – SMPD

• 49 – SMDY

40024: User Full Scale

Register 40024 is the “4-20 Flow Out” full scale value. Changing this only affects the 4-20

flow output and will not affect the Modbus data.

40026: Totalizer Flow Units

ASCII string shows the currently selected totalizer unit on the instrument. The unit is linked

to the flow unit. Changing the flow unit will change the totalizer unit.

40028: Totalizer Unit Index

Value shows which unit is selected on the instrument (read only). These correspond with the

Flow Unit Index with the integral time stripped off. Examples: 1= SCFM flow unit or SCF

total unit, 2= SCFH flow unit or SCF total unit.

40029: Temperature Unit

ASCII data string shows the currently selected temperature unit on the instrument. Use

Register 40030 to select a different unit.

40030: Temperature Unit Index

Value shows which temperature unit is selected on the instrument:

• 0 – F

• 1 – C

• 2 – K

• 3 – R

Warning!

The totalizer will not work when the velocity units are selected (units 40-49).

16

40031: Pressure Unit

ASCII string shows the currently selected pressure unit on the instrument. Use register 40035

to select a different unit

40035: Pressure Unit Index

Value shows which pressure unit is selected on the instrument:

• 0 – PSIA

• 1 – PSIG

• 2 – Bar A

• 3 – Bar G

• 4 – KPa A

• 5 – KPa G

• 6 – Kg

40036: Standard Temperature

Value shows the standard temperature.

40038: Standard Temperature Unit Index

Value shows which temperature unit is selected as standard temperature:

• 0 – F

• 1 – C

• 2 – K

• 3 – R

40039: Standard Pressure

Value shows the standard pressure.

40041: Standard Pressure Index

Value shows which pressure unit is selected as the standard pressure:

• 0 – PSIA

• 1 – PSIG

• 2 – Bar A

• 3 – Bar G

• 4 – KPa A

• 5 – KPa G

• 6 – Kg

40042: Normal Temperature

Value shows the normal temperature.

40044: Normal Temperature Unit Index

Value shows which temperature unit is selected as the normal temperature:

• 0 – F

• 1 – C

• 2 – K

• 3 – R

17

40045: Normal Pressure

Value shows the normal pressure.

40047: Normal Pressure Index

Value shows which pressure unit is selected as the normal pressure:

• 0 – PSIA

• 1 – PSIG

• 2 – Bar A

• 3 – Bar G

• 4 – KPa A

• 5 – KPa G

• 6 – Kg

40048: Flow - 4ma Tuning

DAC value that represents 4 mA for the flow output

40049: Flow - 20ma Tuning

DAC value that represents 20 mA for the flow output

40050: Temperature - 4ma Tuning

DAC value that represents 4 mA for the temperature output

40051: Temperature - 20ma Tuning

DAC value that represents 20 mA for the temperature output

40052: Pressure - 4ma Tuning

DAC value that represents 4 mA for the pressure output

40053: Pressure - 20ma Tuning

DAC value that represents 20 mA for the pressure output

40054: Temperature - 4ma Value

Temperature value that 4mA equals

40056: Temperature - 20ma Value

Temperature value that 20mA equals

40058: Pressure - 4ma Value

Pressure value that 4mA equals

40060: Pressure - 20ma Value

Pressure value that 20mA equals

40062: Alarm Active

Note

Registers 40048 to 40060 only affect the three 4-20mA outputs on the

meter, and have would have no effect on the Modbus data.

18

Value indicates which alarm is active (see below). Note: Only one alarm can be active when

the instrument is online.

• 0 - Off

• 1 - Always On (use this to test the alarm circuit)

• 16 - Flow

• 32 - Pressure

• 64 - Temperature

• 128 - Totalizer

40063: Alarm Mode

Value indicates the mode of the current active alarm (flow, temperature, pressure or

totalizer):

• 0 – Alarm set to “Low” mode

• 1 – Alarm set to “High” mode

• 2 – Alarm set to “Window”

The Window Mode (2) is a combination of both “Low” and “High” alarm modes working

together. You will need to provide both “Low” and “High” threshold values for this mode to

work correctly. Example: If the “Low” is set to 10 and the “High” is set to 20, the alarm will

only be active below 10 and above 20.

40064: Flow – Low Alarm Threshold

Value at which the low alarm is triggered

40066: Flow – High Alarm Threshold

Value at which the high alarm is triggered

40068: Temperature – Low Alarm Threshold

Value at which the low alarm is triggered

40070: Temperature – High Alarm Threshold

Value at which the high alarm is triggered

40072: Pressure – Low Alarm Threshold

Value at which the low alarm is triggered

40074: Pressure – High Alarm Threshold

Value at which the high alarm is triggered

40076: Total – Low Alarm Threshold

Value at which the low alarm is triggered

40078: Total – High Alarm Threshold

Value at which the high alarm is triggered

40080: Pipe Diameter

Value of the pipe diameter will be in the units that are currently active.

40082: Pipe Roughness

19

Value indicates the pipe material:

• 0 – PVC

• 1 – Glass

• 2 – Stainless steel-smooth

• 3 – Stainless steel -normal

• 4 – Stainless steel -rough

• 5 – Carbon steel -smooth

• 6 – Carbon steel -normal

• 7 – Carbon steel -rough

• 8 – Carbon-fiber

• 9 – cast-iron

• 10 – concrete

40083: Pipe Diameter Units

Value indicates the current pipe diameter units:

• 0 – Inches

• 1 – Feet

• 2 – Millimeters

• 3 – Meters

40084: Flow Correction

This value is used to alter the flow reading (default = 1.0)

40086: Enable Totalizer

Enable or disable the totalizer:

0 = off

1 = on

40087: Totalizer units per pulse

This is the value that determines when the totalizer output will pulse. Maximum frequency of

the pulse output is 1 Hz.

40089: Totalizer Pulse Output Width

Value which indicates the pulse width of the pulse output:

• 0 – Off

• 1 – On used for testing

• 2 – 50ms

• 3 – 100ms

• 4 – 250ms

40090: Totalizer Reset

Write any value to reset the totalizer.

40091: Password

This register shows the currently active password. Note: the password is only used to control

access to the display module.

20

40092: Standard Temperature Unit

ASCII string shows the temperature unit of the standard temperature:

• F

• C

• K

• R

40093: Normal Temperature Unit

ASCII string shows the temperature unit of the normal temperature:

• F

• C

• K

• R

40094: Standard Pressure Unit

ASCII string shows the pressure unit of the standard pressure:

• Psia

• Psig

• Bar A

• Bar G

• KPa A

• KPa G

• Kg/CM2 A

• Kg/CM2 G

• In H20 A

• In H20 G

• MM H20 A

• MM H20 G

40098: Normal Pressure Unit

ASCII string shows the pressure unit of the normal pressure:

• Psia

• Psig

• Bar A

• Bar G

• KPa A

• KPa G

• Kg/CM2 A

• Kg/CM2 G

• In H20 A

• In H20 G

Strona jest ładowana ...

Sierra QuadraTherm 640i/780i Modbus Instrukcja obsługi

Sierra QuadraTherm 640i/780i Modbus Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty