Moxa ioLogik R1200 Series Instrukcja obsługi

ioLogik R1200 Series User’s Manual

Edition 3.3, February 2018

www.moxa.com/product

ioLogik R1200 Series User’s Manual

The software described in this manual is furnished under a license agreement and may be used only in accordance with

the terms of that agreement.

Copyright Notice

Trademarks

The MOXA logo is a registered trademark of Moxa Inc.

All other trademarks or registered marks in this manual belong to their respective manufacturers.

Disclaimer

Information in this document is subject to change without notice and does not represent a commitment on the part of

Moxa.

Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited

to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the

products and/or the programs described in this manual, at any time.

Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for

its use, or for any infringements on the rights of third parties that may result from its use.

This product might include unintentional technical or typographical errors. Changes are periodically made to the

information herein to correct such errors, and these changes are incorporated into new editions of the publication.

Technical Support Contact Information

www.moxa.com/support

Moxa Americas

Toll

-free: 1-888-669-2872

Tel:

+1-714-528-6777

Fax:

+1-714-528-6778

Moxa China (Shanghai office)

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

M

oxa Asia-Pacific

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045

Table of Contents

1. Overview ........................................................................................................................................... 1-1

Introduction ....................................................................................................................................... 1-2

Product Features ................................................................................................................................ 1-2

Package Checklist ............................................................................................................................... 1-2

Product Model Information ................................................................................................................... 1-2

Ordering Information ................................................................................................................... 1-2

Specifications ..................................................................................................................................... 1-3

Common Specifications ................................................................................................................ 1-3

ioLogik R1210 ............................................................................................................................. 1-4

ioLogik R1212 ............................................................................................................................. 1-4

ioLogik R1214 ............................................................................................................................. 1-5

ioLogik R1240 ............................................................................................................................. 1-6

ioLogik R1241 ............................................................................................................................. 1-6

Physical Dimensions ............................................................................................................................ 1-7

Hardware Reference ............................................................................................................................ 1-7

Panel Guide ................................................................................................................................ 1-7

LED Indicators ............................................................................................................................ 1-8

Switch Settings ........................................................................................................................... 1-8

DI Circuit Diagram....................................................................................................................... 1-8

DIO Circuit Diagram .................................................................................................................... 1-9

Relay Circuit Diagram ................................................................................................................ 1-10

AI Circuit Diagram ..................................................................................................................... 1-10

2. Initial Setup ...................................................................................................................................... 2-1

Hardware Installation .......................................................................................................................... 2-2

Connecting the Power .................................................................................................................. 2-2

Grounding the ioLogik R1200 ........................................................................................................ 2-2

Connecting to Serial Interface ....................................................................................................... 2-2

Mounting the ioLogik R1200 ......................................................................................................... 2-2

Connecting to Digital Sensors and Devices ..................................................................................... 2-3

RS-485 Networks ........................................................................................................................ 2-4

Modbus/RTU Devices ................................................................................................................... 2-5

Dual RS-485 or Repeater Settings ................................................................................................. 2-5

Jumper Settings (DIO and AI) ....................................................................................................... 2-6

Pull High/Low DIP Switch Settings for the RS-485 Port ..................................................................... 2-6

Software Installation ........................................................................................................................... 2-7

ioSearch Installation .................................................................................................................... 2-7

Initial Setup by USB .................................................................................................................... 2-9

Restore Factory Default Settings ................................................................................................. 2-10

3. Using ioSearch .................................................................................................................................. 3-1

Introduction to ioSearch ...................................................................................................................... 3-2

ioSearch Main Screen .......................................................................................................................... 3-2

Main Screen Overview ......................................................................................................................... 3-2

ioSearch Setup ................................................................................................................................... 3-3

System ...................................................................................................................................... 3-3

Sort ........................................................................................................................................... 3-5

Help .......................................................................................................................................... 3-6

Quick Links ........................................................................................................................................ 3-6

Main Functions ................................................................................................................................... 3-6

Locate ....................................................................................................................................... 3-6

Connect/Disconnect ..................................................................................................................... 3-6

Firmware Upgrade ....................................................................................................................... 3-7

Import ....................................................................................................................................... 3-7

Export ....................................................................................................................................... 3-7

Change Server Name ................................................................................................................... 3-7

Restart System ........................................................................................................................... 3-8

Delete ioLogik Device ................................................................................................................... 3-8

Reset to Default .......................................................................................................................... 3-8

Main Screen ....................................................................................................................................... 3-9

I/O Configuration Tab (General) .................................................................................................... 3-9

Configuring Digital Input Channels ................................................................................................ 3-9

Configuring Digital Output Channels ............................................................................................ 3-11

Configuring Analog Input Channels .............................................................................................. 3-13

AI Input Range ......................................................................................................................... 3-13

Configuring Analog Output Channels ............................................................................................ 3-14

Server Info Tab ................................................................................................................................ 3-16

Server Settings Tab (General) ..................................................................................................... 3-17

Watchdog ................................................................................................................................. 3-18

A. Modbus Mapping ............................................................................................................................... A-1

ioLogik R1200 System Modbus Address and Register Map ........................................................................ A-2

ioLogik R1210 Modbus Address and Register Map ................................................................................... A-3

ioLogik R1212 Modbus Address and Register Map ................................................................................. A-11

ioLogik R1214 Modbus Address and Register Map ................................................................................. A-24

ioLogik R1240 Modbus Address and Register Map ................................................................................. A-31

ioLogik R1241 Modbus Address and Register Map ................................................................................. A-36

B. Factory Defaults ................................................................................................................................ B-1

C. Pinouts .............................................................................................................................................. C-1

D. FCC Interference Statement .............................................................................................................. D-1

E. European Community (CE) ................................................................................................................ E-1

1

1. Overview

The following topics are covered in this chapter:



Introduction



Product Features



Package Checklist



Product Model Information

 Ordering Information



Specifications

 Common Specifications

 ioLogik R1210

 ioLogik R1212

 ioLogik R1214

 ioLogik R1240

 ioLogik R1241



Physical Dimensions



Hardware Reference

 Panel Guide

 LED Indicators

 Switch Settings

 DI Circuit Diagram

 DIO Circuit Diagram

 Relay Circuit Diagram

 AI Circuit Diagram

ioLogik R1200 Series Overview

1-2

Introduction

The ioLogik R1200 is an industrial grade, wide-temperature serial remote I/O device equipped with dual

RS-485 ports that allow users to select between two RS-485 serial ports or switch to a built-in repeater.

Applications such as factory automation, security and surveillance systems, and tunnel monitoring can use the

RS-485 serial line to set up multi-drop device configurations through serial cables. Furthermore, a technician

with no serial background can upload device configurations and firmware via USB at the field site without

bringing a PC to the field site. The ioLogik R1200 lets you easily build an industrial grade, long distance

communication system with standard PC hardware, and extends the communication distance by 4,000 ft.

(1,200 m).

Product Features

• Upload and install device configurations and firmware via USB

• Multi-drop support for device configuration and firmware upgrade via RS-485

• Remote firmware updates via RS-485

• Dual RS-485 ports with built-in repeater

• Wide temperature (-40 to 85°C), 1 kV surge protection, and 3 kV I/O isolation between I/O channels,

networks and power circuits

• Multi-functional I/O support for DI, event counter, DO, and pulse output

• Modbus/RTU support for control by SCADA software, including Wonderware InTouch and GE Intellution

iFix32

• Monitoring and configuration via ioSearch Windows utility

• Hardware detection over RS-485 via ioSearch

Package Checklist

The ioLogik R1200 is shipped with the following items:

• 1 ioLogik R1200 remote I/O product

• Quick Installation Guide (printed)

NOTE

Con

tact your sales representative if any of the above items are missing or damaged.

Product Model Information

Ordering Information

ioLogik R1210 RS-485 remote I/O, 16 DIs, -10 to 75°C operating temperature.

ioLogik R1210-T RS-485 remote I/O, 16 DIs, -40 to 85°C operating temperature.

ioLogik R1212 RS-485 remote I/O, 8 DIs, 8 DIOs, -10 to 75°C operating temperature.

ioLogik R1212-T RS-485 remote I/O, 8 DIs, 8 DIOs, -40 to 85°C operating temperature.

ioLogik R1214 RS-485 remote I/O, 6 DIs, 6 Relays, -10 to 75°C operating temperature.

ioLogik R1214-T RS-485 remote I/O, 6 DIs, 6 Relays, -40 to 85°C operating temperature.

ioLogik R1240 RS-485 remote I/O, 8 AIs, -10 to 75°C operating temperature.

ioLogik R1240-T RS-485 remote I/O, 8 AIs, -40 to 85°C operating temperature.

ioLogik R1241 RS-485 remote I/O, 4 AOs, -10 to 75°C operating temperature.

ioLogik R1241-T RS-485 remote I/O, 4 AOs, -40 to 85°C operating temperature.

ioLogik R1200 Series Overview

1-3

Specifications

Common Specifications

Serial Communication

Interface:

RS-485-2w: Data+, Data-, GND (5-contact terminal block)

Serial Line Protection:

15 kV ESD for all signals, Level 2 surge, EN 61000-4-5 (1 kV)

Serial Communication Parameters

Parity:

None, Even, Odd (default = None)

Data Bits:

8

Stop Bits:

1, 2 (default = 1)

Baudrate:

1200 to 921.6 kbps (default = 9600)

Pull High/Low Resistor for RS

-485: 1 kΩ, 150 kΩ

Protocols:

Modbus RTU

Physical Characteristics

Wiring:

I/O cable max. 16 AWG

Dimensions:

27.8 x 124 x 84 mm (1.09 x 4.88 x 3.31 in)

Environmental Limits

Operating Temperature:

Standard Models:

-10 to 75°C (14 to 167°F)

Wide Temp. Models:

-40 to 85°C (-40 to 185°F)

Storage Temperature:

-40 to 85°C (-40 to 185°F)

Ambient Relative Humidity:

5 to 95% (non-condensing)

Standards and Certifications

Safety:

UL 508

EMI:

EN 550

32, EN 61000-3-2, EN 61000-3-3, FCC Part 15 Subpart B Class A

EMS:

EN 55024, IEC 61000

-4, IEC 61000-6

Shock:

IEC 60068-2-27

Freefall:

IEC 60068-2-32

Vibration:

IEC 60068-2-6

Warranty

Warranty Period:

5 years (excluding the ioLogik R1214)

Details:

See www.moxa.com/warranty

ioLogik R1200 Series Overview

1-4

ioLogik R1210

Inputs and Outputs

Digital Inputs:

16 channels

Isolation:

3K VDC or 2K Vrms

Digital Input

Sensor Type:

Wet Contact (NPN or PNP), Dry Contact

I/O Mode:

DI or Event Counter

Dry Contact:

• On: short to GND

• Off: open

Wet Contact (DI to

COM):

• On:

10 to 30 VDC

• Off: 0 to 3 VDC

Common Type:

8 points per COM

Counter Frequency:

2.5 kHz, power off storage

Digital Filtering Time Interval:

Software selectable

Power Requirements

Power Input:

24 VDC nominal, 12 to 48 VDC

Power Consumption:

154 mA @ 24VDC

ioLogik R1212

Inputs and Outputs

Digital Inputs:

8 channels

Configurable DIOs:

8 channels

Isolation:

3K VDC or 2K Vrms

Digital Input

Sensor Type:

Wet Contact (NPN or PNP), Dry Contact

I/O Mode:

DI or Event Counter

Dry Contact:

• On: short to GND

• Off: open

Wet Contact (DI to

COM):

• On:

10 to 30 VDC

• Off: 0 to 3 VDC

Common Type:

8 points per COM

Counter Frequency:

2.5 kHz, power off storage

Digital Filtering Time Interval:

Software selectable

Digital Output

Type:

Sink

I/O Mode:

DO or Pulse Output

Pulse Output Frequency:

5 kHz

Over

-voltage Protection: 45 VDC

Over

-current Protection: 2.6 A (4 channels @ 650 mA)

Over

-temperature Shutdown: 175°C (typical), 150°C (min.)

Current Rating:

200 mA per channel

Power Requirements

Power Input:

24 VDC nominal, 12 to 48 VDC

Power Consumption:

187 mA @ 24VDC

ioLogik R1200 Series Overview

1-5

ioLogik R1214

Inputs and Outputs

Digital Inputs:

6 channels

Relay Outputs:

6 channels

Isolation:

3K VDC or 2K Vrms

Digital Input

Sensor Type:

Wet Contact (NPN or PNP), Dry Contact

I/O Mode:

DI or Event Counter

Dry Contact:

• On: short to GND

• Off: open

Wet Contact (DI to

COM):

• On:

10 to 30 VDC

• Off: 0 to 3 VDC

Common Type:

6 points per COM

Counter Frequency:

2.5 kHz, power off storage

Digital Filtering Time Interval:

Software selectable

Relay Output

Type:

Form A (N.O.) power relay

Contact Current Rating:

• Resistive

Load: 5 A @ 30 VDC, 250 VAC, 110 VAC

Breakdown Voltage:

500 VAC

Relay On/Off Time:

1500 ms (Max.)

Initial Insulation Resistance:

1000 M ohms (min.) @ 500 VDC

Mechanical Endurance:

5,000,000 operations

Electrical Endurance:

100,000 operations @ 5 A resistive load

Contact Resistance:

100 m ohms (max.)

Pulse Output:

0.3 Hz at rated load

Note: Ambient humidity must be non

-

condensing and remain between 5 and 95%. The relays of the ioLogik

R1214 may malfunction when operating

in high condensation environments below 0°C.

Power Requirements

Power Input:

24 VDC nominal, 12 to 48 VDC

Power Consumption:

207 mA @ 24VDC

ioLogik R1200 Series Overview

1-6

ioLogik R1240

Inputs and Outputs

Analog Inputs:

8 channels

Isolation:

3K VDC or 2K Vrms

Analog Input

Type:

Differential input

Resolution:

16 bits

I/O Mode:

Voltage / Current

Input Range:

0 to 10 VDC, 0 to 20 mA, 4 to 20 mA (burn-out mode)

Accuracy:

±0.1% FSR @ 25°C

±0.3% FSR @

-10 and 60°C

±0.5% FSR @

-40 and 75°C

Sampling Rate (all channels):

12 Hz

Input Impedance:

10M ohms (min.)

Built

-in Resistor for Current Input: 120 ohms

Power Requirements

Power Input:

24 VDC nominal, 12 to 48 VDC

Power Consumption:

216 mA @ 24VDC

ioLogik R1241

Inputs and Outputs

Analog Outputs:

4 channels

Isolation:

3K VDC or 2K Vrms

Analog Output

Resolution:

12 bits

Output Range:

0 to 10 VDC, 4 to 20 mA

Voltage Output:

10 mA (max.)

Accuracy:

±0.1% FSR @ 25°C

±0.3% FSR @

-40 and 75°C

Load Resistor:

• Internal power: 400 ohms

• External 24V power: 1000 ohms

Power Requirements

Power Input:

24 VDC nominal, 12 to 48 VDC

Power Consumption:

343 mA @ 24VDC

ioLogik R1200 Series Overview

1-7

Physical Dimensions

The dimensions of the ioLogik R1200 product are 27.8 x 124 x 84 mm. The connector for the two RS-485 ports

is a 5-pin 3.81 terminal block (2 RS-485 ports with 1 ground pin). The power connector is on the top and the

reset button is on the bottom of the product. There are also two dials for Board ID setup, and a 2-pin DIP switch

for “Initial/Run” mode and “Dual RS-485/Repeater” mode setup.

Hardware Reference

Panel Guide

ioLogik R1200 Series Overview

1-8

NOTE

The RESET button restarts the server and resets all settings to factory defaults. Use a pointed object such as

a straightened paper clip to hold down the reset button for 5 seconds. The factory defaults will load once the

READY LED turns green again. You may then release the RESET button.

LED Indicators

LED State Description

Power (PWR) Amber System power is ON

OFF System power is OFF

Read (RDY) Green System is ready

Flashing Flashes every 1 sec when the Locate function is triggered

Flashing Flashes every 0.5 sec when the firmware is being upgraded

Flashing Flashing USB upgrade is triggered

OFF System is not ready.

Port 1 (P1) Green Serial connection enabled

Flashing Transmitting or receiving data

Port 2 (P2) Green Serial connection enabled

Flashing Transmitting or receiving data

Switch Settings

The R1200 series provides Dual/Rep and Run/Initial switch settings for setting the communication mode.

Dual (Default) Dual RS-485 mode

Rep Repeater mode

Run User defined communication parameters

Initial (Default) Initial RS-485 communication parameters

DI Circuit Diagram

ioLogik R1200 Series Overview

1-9

DIO Circuit Diagram

ioLogik R1200 Series Overview

1-10

Relay Circuit Diagram

AI Circuit Diagram

2

2. Initial Setup

The following topics are covered in this chapter:



Hardware Installation

 Connecting the Power

 Grounding the ioLogik R1200

 Connecting to Serial Interface

 Mounting the ioLogik R1200

 Connecting to Digital Sensors and Devices

 RS-485 Networks

 Modbus/RTU Devices

 Dual RS-485 or Repeater Settings

 Jumper Settings (DIO and AI)

 Pull High/Low DIP Switch Settings for the RS-485 Port



Software Installation

 ioSearch Installation

 Initial Setup by USB

 Restore Factory Default Settings

ioLogik R1200 Series Initial Setup

2-2

Hardware Installation

Connecting the Power

Connect the 12 to 48 VDC power line to the ioLogik R1200’s terminal block on the top panel. If power is properly

supplied, the Power LED will glow a solid amber color.

ATTENTION

Determine the maximum possible current for each power wire and common wire. Observe all electrical codes

dictating the maximum current allowable for

each wire size. If the current exceeds the maximum rating, the

wiring could overheat, causing serious damage to your equipment. For safety reasons, we recommend an

average cable size of 22 AWG. However, depending on the current load, you may want to adjust your cable size

(the maximum wire size for power connectors is 2 mm).

Grounding the ioLogik R1200

The ioLogik

R

1200 is equipped with a grounding point on the terminal block located on the top panel.

Connect the ground pin if an earth ground is

available.

Connecting to Serial Interface

TB1 and TB2 (two RS-485 2-wire connectors)

TB1 (RS-485) TB2 (RS-485)

Pin 1 2 3 4 5 3

Signal D1+ D1- GND D2+ D2- GND

NOTE

TB1 and TB2 share the same ground

.

Mounting the ioLogik R1200

The ioLogik R1200 can be used with both DIN rail and wall mounting applications.

ioLogik R1200 Series Initial Setup

2-3

Connecting to Digital Sensors and Devices

Digital Input/Output (Sink Type)

A Dry Contact is a contact that works without a power source.

A Wet Contact is a contact that must work with a power source.

Analog Input/Output

Relay Output (Form A)

ioLogik R1200 Series Initial Setup

2-4

NOTE

A “load” in a circuit schematic is a component or portion of the circuit that consumes electric power. For the

diagrams shown in this document, “load” refe

rs to the devices or systems connected to the remote I/O unit.

RS-485 Networks

RS-485 permits a balanced transmission line to be shared in a party line or multi-drop configuration. As many

as 32 driver/receiver pairs can share a multi-drop connection on a single two-wire bus. The length of the

network is limited to 4,000 ft between the first node and the last node. You can use RS-485 in two-wire or

four-wire multi-drop network applications.

In an RS-485 four- wire network, one node must be a master node and all others slave nodes. The master does

not require tri-state output.

NOTE

The transmission line is terminated on both ends of the line but not at

drop points in the middle of the line.

Termination is only required with high data

rates or long wire runs.

Setting the Device ID for RS-485 Serial Communication

The RS-485 port is used to communicate with other RS-485 devices or to link to another ioLogik RS-485 I/O

server. The RS-485 port can run Modbus/RTU or I/O command sets. The device ID for each ioLogik R1200

device can be set to any number from 01 to 99 by turning the two rotary dials on the back of the device. The

x1 dial (shown on the left in the figure below) represents the ones place and the x10 dial (shown on the right

in the figure below) represents the tens place. Settings such as the baud rate, parity check, data bits, and stop

bit are configured by software.

Serial Communication Parameters (Initial State)

Communication Parameters (Initial mode)

Parity None, Even, Odd (default = None)

Data Bits 8

Stop Bits 1, 2 (default = 1)

Baudrate 1200 to 921.6 kbps (default = 9600)

Serial Communication Initial Setup

During your initial setup, set the switch to “Initial” mode to configure your device, after configuration is done

flip the switch back to “Run” mode.

NOTE

The

initial communication setting is: baudrate = 9600, n, 8, 1.

ioLogik R1200 Series Initial Setup

2-5

Modbus/RTU Devices

The RS-485 port runs Modbus/RTU and can connect to any Modbus device. You may use different methods to

connect different combinations of ioLogik R12000 servers and other Modbus devices. Some examples are

shown below:

Connecting One Modbus/RTU Device

Connecting Multiple Modbus/RTU Devices

Dual RS-485 or Repeater Settings

Dual RS-485: Switching the dial to “Dual” will divide the RS-485 port into two separate RS-485 ports for users

to run dual RS-485 lines.

Repeater: Switching the dial to “Rep” will set the ioLogik R1200 to act as a repeater.

NOTE

In

Repeater mode, when signals pass through one machine, the latency will increase by 1 byte

with a maximum

of

10 ms at 1200 bps baudrate.

ioLogik R1200 Series Initial Setup

2-6

Jumper Settings (DIO and AI)

The models with DIO or AI channels require configuring the jumpers inside the cover. Remove the screw

located on the back panel and open the cover to configure the jumpers.

DIO mode configuration is shown to the right (default: DO Mode).

Analog mode configuration is shown to the right (default: Voltage Mode).

ATTENTION

Remove the screw on the back panel and open the cover to configure the jumpers.

Pull High/Low DIP Switch Settings for the RS-485 Port

In some critical environments, you may need to add termination resistors to prevent the reflection of serial

signals. When using termination resistors, it is important to set the pull high/low resistors correctly so that the

electrical signal is not corrupted. Since there is no resistor value that works for every environment, DIP

switches are used to set the pull high/low resistor valve for each RS-485 port.

Strona jest ładowana ...

Moxa ioLogik R1200 Series Instrukcja obsługi

Moxa ioLogik R1200 Series Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty