Parkside 312188 Operating And Safety Instructions Manual

Typ
Operating And Safety Instructions Manual

Ten podręcznik jest również odpowiedni dla

IAN 312188
SLIDING COMPOUND MITRE SAW PZKS 2000 A1
CHAT
KAPP- UND ZUGSÄGE
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
DE
SKERSINIO IR IŠILGINIO PJOVIMO STAKLĖS
Nurodymai dėl valdymo ir saugumo
Originalios naudojimo instrukcijos vertimas
LT
KAPSÅG
Instruktioner och säkerhetsanvisningar för
Översättning från originalmanualen
SE
SLIDING COMPOUND MITRE SAW
Operating and Safety Instructions
Translation of Original Operating Manual
GB
TARCZÓWKA I PIŁA DWURĘCZNA
Wskazówki dotyczące obsługi i bezpieczeństwa
Tłumaczenie oryginalnej instrukcji obsługi
PL
LTPLSE
GB Operating and Safety Instructions Page 01
SE Instruktioner och säkerhetsanvisningar för Sida 14
PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 27
LT Nurodymai dėl valdymo ir saugumo Puslapis 41
DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 54
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen Funktionen des Gerätes vertraut.
DE AT CH
Fyll på sidan med illustrationerna innan du läser och bekanta dig med alla funktioner på enheten.
SE
Przed przeczytaniem proszę rozłyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi funkcjami urządzenia.
PL
Prieš skaitydami išlankstykite lapa su paveiksleliais ir susipažinkite su visomis prietaiso funkcijomis.
LT
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.
GB
2
4
1
3
5
1
10
2
4
5
7
24
25
32
23
24a
12131415
16
17
7
11
8
9
3
16a
23
11
35
35
21
22
27a
26a
19
18
20
16b
7a
27
22
26
6
16a
8
36
D
10
6 7
13
988
14
11
12
!
1918
14
6
1
14
2
7
20
C
C
6
4
16a
3
A
max. 8 mm
4
6
B
4
4
7
7
14
14
14
24
24a
25
5a
26
27
14
7
22
13
max. 8 mm
16
17 18
19
15
20
21
22
5
29
34
31
33
30
28
C
6
17
32
32a
32b
E
E
E
32b
1GB
Table of contents: Page:
1. Introduction ..........................................................................................................................................................................................................3
2. Device description (fig. 1-22) .............................................................................................................................................................................3
3. Scope of delivery ................................................................................................................................................................................................3
4. Intended use ........................................................................................................................................................................................................ 4
5. Safety information ............................................................................................................................................................................................... 4
6. Technical data ..................................................................................................................................................................................................... 7
7. Before starting the equipment ............................................................................................................................................................................8
8. Attachment and operation ..................................................................................................................................................................................8
9. Transport ............................................................................................................................................................................................................10
10. Maintenance .....................................................................................................................................................................................................10
11. Storage ..............................................................................................................................................................................................................11
12. Electrical connection .........................................................................................................................................................................................11
13. Disposal and recycling .....................................................................................................................................................................................11
14. Troubleshooting .................................................................................................................................................................................................12
15. Warranty certificate ..........................................................................................................................................................................................13
2 GB
Explanation of the symbols on the equipment
GB
Before commissioning, read and observe the operating instructions and safety instructions!
GB
Wear safety goggles!
GB
Wear ear-muffs!
GB
Wear a breathing mask!
GB
Important! Risk of injury. Never reach into the running saw blade!
GB
Important! Laser radiation
GB
Protection Class II (double shielded)
3GB
1. Introduction
MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
we hope your new tool brings you much enjoyment and suc-
cess.
NOTE:
According to the applicable product liability laws, the manu-
facturer of the device does not assume liability for damages
to the product or damages caused by the product that occurs
due to:
Improper handling,
Non-compliance of the operating instructions,
Repairs by third parties, not by authorized service techni-
cians,
Installation and replacement of non-original spare parts,
Application other than specified,
A breakdown of the electrical system that occurs due to the
non-compliance of the electric regulations and VDE regula-
tions 0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the operating instructions
before installing and commissioning the device.
The operating instructions are intended to help the user to
become familiar with the machine and take advantage of its
application possibilities in accordance with the recommenda-
tions.
The operating instructions contain important information
on how to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, reduce
downtimes and how to increase reliability and service life of
the machine.
In addition to the safety regulations in the operating instruc-
tions, you have to meet the applicable regulations that apply
for the operation of the machine in your country.
Keep the operating instructions package with the machine at
all times and store it in a plastic cover to protect it from dirt
and moisture. Read the instruction manual each time before
operating the machine and carefully follow its information.
The machine can only be operated by persons who were
instructed concerning the operation of the machine and who
are informed about the associated dangers. The minimum age
requirement must be complied with.
In addition to the safety instructions contained in this operat-
ing manual and the specific regulations of your country,
the technical rules generally accepted for the operation of
machines of the same type must be observed.
We accept no liability for damage or accidents which arise
due to non-observance of these instructions and the safety
information.
2. Device description (fig. 1-22)
1. Handle
2. ON/OFF switch
3. Lock switch
4. Machine head
5. Moving saw blade guard
6. Saw blade
7. Clamping device
8. Workpiece support
9. Set screw for workpiece support
10. Table insert
11. Handle / Set screw for rotary table
12. Pointer
13. Scale
14. Rotary table
15. Fixed saw table
16. Stop rail
16a. Movable stop rail
16b. Set screw
17. Sawdust bag
18. Scale
19. Pointer
20. Set screw for drag guide
21. Drag guide
22. Set screw
23. Locking bolt
24. Screw for cutting depth limiting
25. Stop for cutting depth limiting
26. Adjusting screw (90°)
27. Adjusting screw (45°)
28. Flange screw
29. Outer flange
30. Saw shaft lock
31. Inner flange
32. Laser
33. ON/OFF switch laser
34. Guide bracket
35. Latched position lever
36. Tilt protection
A.) 90° stop angle (not supplied)
B.) 45° stop angle (not supplied)
C.) Allen key, 6 mm
D.) Allen key, 3 mm
E.) Philips head screw (Laser)
3. Scope of delivery
Crosscut, drag and mitre saw
2 x Clamping device (7) (preassembled)
2 x Workpiece support (8) (preassembled)
Sawdust bag (17)
Allen key 6 mm (C)
Allen key 3 mm (D)
Operating manual
4 GB
4. Intended use
The crosscut, drag and mitre saw is designed to crosscut wood
and plastic respective of the machine’s size. The saw is not de-
signed for cutting firewood.
Warning! Do not use the saw to cut materials other than
those specified described in manual.
Warning! The supplied saw blade is only intended for the
sawing of wood! Do not use this blade for the sawing of fire-
wood!
The equipment is to be used only for its prescribed purpose.
Any other use is deemed to be a case of misuse. The user / op-
erator and not the manufacturer will be liable for any damage
or injuries of any kind caused as a result of this.
The equipment is to be operated only with suitable saw blades.
It is prohibited to use any type of cutting-off wheel.
To use the equipment properly you must also observe the safety
information, the assembly instructions and the operating instruc-
tions to be found in this manual.
All persons who use and service the equipment have to be
acquainted with this manual and must be informed about the
equipment’s potential hazards. It is also imperative to observe
the accident prevention regulations in force in your area. The
same applies for the general rules of health and safety at work.
The manufacturer will not be liable for any changes made to
the equipment nor for any damage resulting from such chang-
es. Even when the equipment is used as prescribed it is still im-
possible to eliminate certain residual risk factors. The following
hazards may arise in connection with the machine’s construc-
tion and design:
Contact with the saw blade in the uncovered saw zone.
Reaching into the running saw blade (cut injuries).
Kick-back of workpieces and parts of workpieces.
Saw blade fracturing.
Catapulting of faulty carbide tips from the saw blade.
Damage to hearing if ear-muffs are not used as necessary.
Harmful emissions of wood dust when used in closed rooms.
Please note that our equipment has not been designed for use
in commercial, trade or industrial applications. Our warranty
will be voided if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.
5. Safety information
General safety information for power tools
m WARNING! Read all safety warnings, instruc-
tions, illustrations and technical data provided
with this power tool. Failure to follow the warnings and in-
structions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future refer-
ence.
The term “power tool” used in the safety instructions refers to
mains powered power tools (with power cord) and cordless
power tools (without power cord).
Workplace safety
a) Keep your workplace clean and well illumi-
nated.
Disorderliness and poorly illuminated workplaces may
Iead to accidents.
b) Do not operate the power tool in explosive
atmospheres with inflammable liquids, gases
or dust.
Power tools generate sparks which may ignite dust or va-
pours.
c) Keep children and other persons away from
the power tool during operation.
You may lose control of the tool if you are distracted.
Electric safety
a) The plug of the power tool must fit into the
socket.
Do not modify the plug in any way. Do not use adapter
plugs together with grounded power tools. Unmodified
plugs and matching sockets reduce the risk of electric shock.
b) Avoid body contact with grounded surfaces
such as pipes, radiators, ovens and refrigera-
tors. There is an increased risk of electric shock
if your body is grounded.
c) Keep power tools away from rain or humidity.
Water permeation into the power tool will increase the
risk of electric shock.
d) Use the cable solely for its intended purpose.
Do not use the cable to carry or hang up the
power tool or to pull out the plug from the
socket.
Keep the cable away from heat, oil, sharp edges or mov-
ing machine parts. Damaged or twisted cables increase
the risk of electric shock.
e) When working outdoors with power tools,
only use extension cords which are suited for
outdoor areas.
Using extension cords suited for outdoor applications re-
duces the risk of electric shock.
f) lf the operation of power tools in a humid en-
vironment cannot be avoided, you must use a
residual current circuit breaker.
The use of a residual current circuit breaker will reduce the
risk of electric shock.
Personal safety
Pay attention to what you are doing and use
power tools sensibly.
Do not use power tools when you are tired or
under the influence of drugs, alcohol or medi-
cation. A single moment of inattention while using pow-
er tools may cause severe injury.
b) Wear personal protective equipment and safe-
ty goggles.
Wearing personal protective equipment such as a dust
mask, non-skid safety boots, a protective helmet or hear-
ing protection according to the type and application of
the power tool reduces the risk of injury.
5GB
c) Avoid starting the power tool unintentionally.
Make sure that the power tool is switched off
before you connect it to the mains and/or in-
sert a battery, pick it up or carry it. lf you have
your finger on the switch when you carry the power tool,
or if the machine is switched on when you connect it to the
mains, this may result in accidents.
d) Remove adjustment tools or wrenches before
switching on the power tool.
Tools or wrenches in rotating machine parts may cause
injury.
e) Avoid abnormal body positions.
Stand securely and keep your balance at all
times. By doing so, you can control the power tool more
easily in unexpected situations.
f) Wear suitable clothing. Do not wear loose
clothing or jewellery. Keep your hair, cloth-
ing and gloves away from moving parts. Loose
clothing, jewellery or long hair may be trapped in moving
parts.
g) lf dust extraction tools or collection bins can
optionally be attached, you must make sure
that they are connected and correctly used.
Using dust extraction tools may reduce risks caused by
dust.
h) Do not let familiarity gained from frequent use
of the tool allow you to become complacent
and ignore tool safety principles. A careless ac-
tion can cause severe injury within a fraction of a second.
Use and treatment of the power tool
a) Do not overload the tool.
Use the appropriate power tool for your type of work.
With appropriate power tools, you can work better and
more safely within the given power range.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that can-
not be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source
and/or remove the battery pack, if detach-
able, from the power tool before making any
adjustments, changing accessories, or storing
power tools.
This preventive safety measure reduces the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach of chil-
dren.
Do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power tools
are dangerous in the hands of untrained users.
e) Carefully maintain power tools and accesso-
ries.
Check moving parts for proper function and smooth run-
ning, and check whether there are parts which are bro-
ken or damaged to the extent that the functionality of the
power tool is impaired. Have damaged parts repaired
before using the power tool. Many accidents are caused
by poorly-maintained power tools.
f) Keep cutting tools sharp and clean. Carefully
maintained cutting tools with sharp edges are
less likely to jam and can be guided more eas-
ily.
g) Use power tools, accessory parts, insertion
tools, etc. in compliance with these instruc-
tions.
Take into account the working conditions and the activity
which is to be carried out. Using power tools for appli-
cations other than those intended may cause dangerous
Situations.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery han-
dles and grasping surfaces do not allow for safe handling
and control of the power tool in unexpected situations.
Service
a) Have your power tool repaired by qualified
specialists only, and always use original spare
parts for repair. This is to maintain the safety of the
power tool.
Warning! This electric tool generates an electromagnetic field
during operation. This field can impair active or passive medi-
cal implants under certain conditions. In order to prevent the
risk of serious or deadly injuries, we recommend that persons
with medical implants consult with their physician and the man-
ufacturer of the medical implant prior to operating the electric
tool.
Safety instructions for mitre saws
a) Mitre saws are intended to cut wood or wood-
like products, they cannot be used with abra-
sive cut-off wheels for cutting ferrous material
such as bars, rods, studs, etc. Abrasive dust causes
moving parts such as the lower guard to jam. Sparks from
abrasive cutting will burn the lower guard, the kerf insert
and other plastic parts.
b) Use clamps to support the workpiece when-
ever possible. If supporting the workpiece by
hand, you must always keep your hand at least
100 mm from either side of the saw blade. Do
not use this saw to cut pieces that are too small
to be securely clamped or held by hand. If your
hand is placed too close to the saw blade, there is an in-
creased risk of injury from blade contact.
c) The workpiece must be stationary and clamped
or held against both the fence and the table.
Do not feed the workpiece into the blade or
cut “freehand” in any way. Unrestrained or moving
workpieces could be thrown at high speeds, causing injury.
d) Push the saw through the workpiece. Do not
pull the saw through the workpiece. To make
a cut, raise the saw head and pull it out over
the workpiece without cutting, start the motor,
press the saw head down and push the saw
through the workpiece. Cutting on the pull stroke is
likely to cause the saw blade to climb on top of the work-
piece and violently throw the blade assembly towards the
operator.
6 GB
e) Never cross your hand over the intended line of
cutting either in front or behind the saw blade.
Supporting the workpiece “cross handed” i.e. holding the
workpiece to the right of the saw blade with your left hand
or vice versa is very dangerous.
f) Do not reach behind the fence with either hand
closer than 100 mm from either side of the saw
blade, to remove wood scraps, or for any other
reason while the blade is spinning. The proximity
of the spinning saw blade to your hand may not be obvi-
ous and you may be seriously injured.
g) Inspect your workpiece before cutting. If the
workpiece is bowed or warped, clamp it with
the outside bowed face toward the fence. Al-
ways make certain that there is no gap be-
tween the workpiece, fence and table along
the line of the cut. Bent or warped workpieces can
twist or shift and may cause binding on the spinning saw
blade while cutting. There should be no nails or foreign
objects in the workpiece.
h) Do not use the saw until the table is clear of all
tools, wood scraps, etc., except for the work-
piece. Small debris or loose pieces of wood or other ob-
jects that contact the revolving blade can be thrown with
high speed.
i) Cut only one workpiece at a time. Stacked multiple
workpieces cannot be adequately clamped or braced and
may bind on the blade or shift during cutting.
j) Ensure the mitre saw is mounted or placed on
a level, firm work surface before use. A level and
firm work surface reduces the risk of the mitre saw becom-
ing unstable.
k) Plan your work. Every time you change the
bevel or mitre angle setting, make sure the
adjustable fence is set correctly to support the
workpiece and will not interfere with the blade
or the guarding system. Without turning the tool
“ON” and with no workpiece on the table, move the saw
blade through a complete simulated cut to assure there will
be no interference or danger of cutting the fence.
l) Provide adequate support such as table exten-
sions, saw horses, etc. for a workpiece that is
wider or longer than the table top. Workpieces
longer or wider than the mitre saw table can tip if not se-
curely supported. If the cut-off piece or workpiece tips, it
can lift the lower guard or be thrown by the spinning blade.
m) Do not use another person as a substitute for a
table extension or as additional support. Unsta-
ble support for the workpiece can cause the blade to bind
or the workpiece to shift during the cutting operation pull-
ing you and the helper into the spinning blade.
n) The cut-off piece must not be jammed or pressed
by any means against the spinning saw blade.
If confined, i.e. using length stops, the cut-off piece could
get wedged against the blade and thrown violently.
o) Always use a clamp or a fixture designed to
properly support round material such as rods
or tubing. Rods have a tendency to roll while being cut,
causing the blade to “bite” and pull the work with your
hand into the blade.
p) Let the blade reach full speed before contact-
ing the workpiece. This will reduce the risk of the work-
piece being thrown.
q) If the workpiece or blade becomes jammed,
turn the mitre saw off. Wait for all moving parts
to stop and disconnect the plug from the power
source and/or remove the battery pack. Then
work to free the jammed material. Continued
sawing with a jammed workpiece could cause loss of con-
trol or damage to the mitre saw.
r) After finishing the cut, release the switch, hold
the saw head down and wait for the blade to
stop before removing the cut-off piece. Reaching
with your hand near the coasting blade is dangerous.
s) Hold the handle firmly when making an incom-
plete cut or when releasing the switch before
the saw head is completely in the down posi-
tion. The braking action of the saw may cause the saw
head to be suddenly pulled downward, causing a risk of
injury.
Safety Instructions for the handling of saw blades
1 Do not use damaged or deformed saw blades.
2 Do not use any insertion tools with cracks. Sort out cracked
insertion tools. Repairs are not permitted.
3 Do not use saw blades made of high speed steel.
4 Check the condition of the saw blades before using the
crosscut, drag and mitre saw.
5 Make sure that a suitable saw blade for the material to
be cut is selected.
6 Only use saw blades recommended by the manufacturer.
Saw blades designed to cut wood and similar materials
must comply with EN 847-1.
7 Do not use saw blades made of high-speed alloy steel
(HSS steel).
8 Only use saw blades for which the maximum permissible
speed is not lower than the maximum spindle speed of the
crosscut, drag and mitre saw and which are suitable for
the material to be cut.
9 Observe the saw blade direction of rotation.
10 Only insertion the saw blade if you have mastered their
use.
11 Observe the maximum speed. The maximum speed speci-
fied on the insertion tool may not be exceeded. If specified,
observe the speed range.
12 Clean grease, oil and water off of the clamping surfaces.
13 Do not use any loose reducing rings or bushes for the
reducing of holes on saw blades.
14 Make sure that fixed reducer rings for securing the inser-
tion tool have the same diameter and have at least 1/3
of the cutting diameter.
15 Make sure that fixed reducer rings are parallel to each
other.
16 Handle insertion tool with caution. They are ideally stored
in the originally package or special containers. Wear
protective gloves in order to improve grip and to further
reduce the risk of injury.
17 Prior to the use of insertion tools, make sure that all protec-
tive devices are properly fastened.
7GB
18 Prior to use, make sure that the insertion tool meets the
technical requirements of this electric tool and is properly
fastened.
19 Only use the supplied saw blade for cutting wood, never
for the processing of metals.
20 Only use saw blade diameters in accordance with the
markings on the saw.
21 Use additional workpiece supports, if required for work-
piece stability.
22 Workpiece support extensions must always be secured
and used during work.
23 Replace table inserts when worn!
24 Avoid overheating of the saw teeth.
25 When sawing plastic, avoid melting of the plastic.
Use the appropriate saw blades for this purpose. Replace
damaged or worn saw blades immediately.
When the saw blade overheats, stop the machine. Allow
the saw blade to cool down before using the machine
again.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
Do not look directly into the laser beam with unprotected
eyes.
Never look into the path of the beam.
Never point the laser beam towards reflecting surfaces and
persons or animals. Even a laser beam with a low output
can cause damage to the eyes.
Caution - methods other than those specified here can result
in dangerous radiation exposure.
Never open the laser module. Unexpected exposure to the
beam can occur.
If you do not use the device for a long time, the batteries
should be removed.
The laser may not be replaced with a different type of laser.
Repairs of the laser may only be carried out by the laser
manufacturer or an authorised representative.
Residual risks
The machine has been built according to the state
of the art and the recognised technical safety re-
quirements. However, individual residual risks can
arise during operation.
Health hazard due to electrical power, with the use of im-
proper electrical connection cables.
Furthermore, despite all precautions having been met, some
non-obvious residual risks may still remain.
Residual risks can be minimised if the „safety instructions“
and the „Proper use“ are observed along with the whole of
the operating instructions.
Do not load the machine unnecessarily: excessive pressure
when sawing will quickly damage the saw blade, which re-
sults in reduced output of the machine in the processing and
in cut precision.
When cutting plastic material, please always use clamps:
the parts which should be cut must always be fixed between
the clamps.
Avoid accidental starting of the machine: the operating but-
ton may not be pressed when inserting the plug in an outlet.
Use the tool that is recommended in this manual. In doing so,
your machine provides optimal performance.
Hands may never enter the processing zone when the ma-
chine is in operation.
Release the handle button and switch off the machine prior
to any operations.
6. Technical data
AC motor.....................................................220 - 240 V
~
50Hz
Power S1 .....................................................................1700 Watt
Operating mode ............................................ S6 25%* 2000W
Idle speed n
0
..............................................................4700 min
-1
Carbide saw blade ...............................ø 210 x ø 30 x 2,6 mm
Number of teeth .......................................................................24
Maximum tooth width of saw blade ..................................3 mm
Swivel range .................................................. -45° / 0°/ +45°
Mitre cut .................................................... 0° bis 45° to the left
Saw width at 90° ................................................. 340 x 65 mm
Saw width at 45° ................................................. 240 x 65 mm
Saw width at 2 x 45°
(double mitre cut) .................................................. 240 x 38 mm
Protection class .................................................................... II /
Weight .......................................................................ca. 12,0 kg
Laser class ...................................................................................2
Wavelength of laser ........................................................ 650 nm
Laser output .....................................................................< 1 mW
* S6, continuous operation periodic duty.
Identical duty cycles with a period at load followed by a period
at no load. Running time 10 minutes; duty cycle is 25% of the
running time.
The work piece must have a minimum height of 3
mm and a minimum width of 10 mm.
Make sure that the workpiece is always secured
with the clamping device.
Noise
Total noise values determined in accordance with EN 62841.
Sound pressure level L
pA
....................... 96,5 dB(A)
Uncertainty K
pA
...............................................3 dB
Sound power level L
WA
........................ 109,5 dB(A)
Uncertainty K
WA
..............................................3 dB
Wear hearing protection.
The effects of noise can cause a loss of hearing
The above-mentioned noise emission values were measured in
accordance with a standardised test procedure and can be
used to compare one power tool with another.
8 GB
The above-mentioned noise emission values can also be used
for the preliminary assessment of exposure.
Warning:
The noise emissions during the actual use of the power tool
may differ from the above-mentioned values depending on
the power tool being used, in particular on the type of work-
piece being processed.
Try to keep emissions as low as possible, for example by
limiting your working time. In this regard, all the operational
cycle phases must be taken into consideration (such as the
times when the tool is switched off or running idle).
7. Before starting the equipment
Open the packaging and remove the device carefully.
Remove the packaging material as well as the packaging
and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport dam-
age.
If possible, store the packaging until the warranty period
has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
The equipment must be set up where it can stand securely.
Secure the machine on a workbench or a base frame with 4
screws (not included in delivery) using the holes on the fixed
saw table (15).
Pull out the pre-installed tilt protection (36) completely and
secure it with an Allen key (D).
All covers and safety devices have to be properly fitted be-
fore the equipment is switched on.
It must be possible for the blade to run freely.
When working with wood that has been processed before,
watch out for foreign bodies such as nails or screws, etc.
Before you press the ON/OFF switch check that the saw
blade is fitted correctly. Moving parts must run smoothly.
Before you connect the equipment to the power supply make
sure the data on the rating plate are dentical to the mains
data.
7.1 Checking the moving saw blade guard safety
device (5)
The saw blade guard protects against accidental contact with
the saw blade and from chips flying around.
Check function
To do so, fold the saw downwards:
The saw blade guard must provide free access to the saw
blade without touching other parts.
When folding the saw upwards into the starting position,
the saw blade guard must cover the saw blade automati-
cally.
8. Attachment and operation
8.1 Attaching the crosscut, drag and mitre saw
(fig.1/2/4/5)
In order to adjust the rotary table (14), loosen the handle
(11) approximately 2 turns and pull up the latched position
lever (35) with your index finger.
Turn the rotary table (14) and pointer (12) to the desired
angle measurement on the scale (13) and use the handle
(11) to secure it.
Pressing the machine head (4) lightly downwards and re-
moving the locking bolt (23) from the motor bracket at the
same time disengages the saw from the lowest position.
Swing the machine head (4) up.
It is possible to secure the clamping devices (7) to the left or
right on the fixed saw table (15). Insert the clamping devices
(7) in the holes on the rear side of the stop rail (16) and
secure it with the star grip screws (7a).
For 0°- 45° mitre cuts, the clamping device (7) must only be
mounted on the right side (see fig. 11-12).
It is possible to tilt the machine head (4) a max. 45° to the
left by loosening the set screw (22).
Workpiece supports (8) must always be secured and used
during work. Set the desired table size by loosening the set
screw (9). Then tighten the set screw (9) again.
8.2 Precision adjustment of the stop for crosscut
90° (fig. 1/2/5/6)
No stop angle included.
Lower the machine head (4) and secure it using the locking
bolt (23).
Loosen the set screw (22).
Position the angle stop (A) between the saw blade (6) and
the rotary table (14).
Loosen the lock nut (26a).
Adjust the adjusting screw (26) until the angle between the
saw blade (6) and rotary table (14) is 90°.
Re-tighten the lock nut (26a).
Subsequently check the position of the angle indicator. If
necessary loosen the pointer (19) using a Philips screwdriv-
er, set to position 0° on the angle scale (18) and re-tighten
the retaining screw.
8.3 Crosscut 90° and turntable 0° (fig. 1/2/7)
In the case of cutting widths up to approx. 100 mm it is possible
to fix the traction function of the saw with the set screw (20) in
the rear position. In this position the machine can be operated
in cross cutting mode. If the cutting width is over 100 mm then
it is necessary to ensure that the set screw (20) is loose and the
machine head (4) can move.
Attention! For 90° crosscuts, the moveable stop rail (16a) must
be fixed in the inner position.
Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) inwards.
The moveable stop rail (16a) must be locked in a position far
enough from the inner position that the distance between the
stop rail (16a) and the saw blade (6) is no more than 8 mm..
Before making the cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
Re-tighten the set screw (16b).
9GB
Move the machine head (4) to its upper position.
Use the handle (1) to push back the machine head (4) and fix
it in this position if required (dependent on the cutting width).
Place the piece of wood to be cut at the stop rail (16) and
on the turntable (14).
Lock the material with the clamping devices (7) on the fixed
saw table (15) to prevent the material from moving during
the cutting operation.
Release the lock switch (3) and press the ON/OFF switch
(2) to start the motor.
With the drag guide (21) fixed in place (21):
use the handle (1) to move the machine head (4) steadily
and with light pressure downwards until the saw blade (6)
has completely cut through the work piece.
With the drag guide (21) not fixed in place (21):
pull the machine head (4) all the way to the front. Lower the
handle (1) to the very bottom by applying steady and light
downward pressure. Now push the machine head (4) slowly
and steadily to the very back until the saw blade (6) has
completely cut through the work piece.
When the cutting operation is completed, move the machine
head back to its upper (home) position and release the ON/
OFF button (2).
Attention! The machine executes an upward stroke auto-
matically due to the return spring, i.e. do not release the han-
dle (1) after completing the cut; instead allow the machine
head to move upwards slowly whilst applying light counter
pressure.
8.4 Crosscut 90° and turntable 0° - 45° (fig.
1/7/8)
The crosscut, drag and mitre saw can be used to make cross-
cuts of 0° -45° to the left and 0° -45° to the right in relation
to the stop rail.
Important! For 90° crosscuts, the moveable stop rail (16a)
must be fixed in the inner position.
Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) inwards.
The moveable stop rail (16a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (16a) and the saw blade (6) amounts to a minimum
of 8 mm.
Before making the cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
Secure the set screw (16b) again.
Loosen the handle (11) if tightened, pull up the latched posi-
tion lever (35) with your index finger and use the handle
(11) to set the rotary table (14) to the desired angle.
The pointer (12) on the rotary table must match the desired
angle on the scale (13) on the fixed saw table (15).
Re-tighten the handle (11) to secure the rotary table (14).
Cut as described under section 8.3.
8.5 Precision adjustment of the stop for mitre cut
45° (fig. 1/2/5/9/10)
No stop angle included.
Lower the machine head (4) and secure it using the locking
bolt (23).
Fix the rotary table (14) in the 0° position.
Attention! For mitre cuts (inclined saw head), the left side of
the moveable stop rails (16a) must be fixed in the outer posi-
tion.
Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) outwards.
The moveable stop rail (16a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (16a) and the saw blade (6) amounts to a maxi-
mum of 8 mm.
The right side of the moveable stop rails (16a) must be in
the inner positiion.
Before making a cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
Loosen the set screw (22) and use the handle (1) to angle
the machine head (4) 45° to the left.
45° - position angle stop (B) between the saw blade (6) and
rotary table (14).
Loosen the lock nut (27a) and adjust the adjustment screw
(27) until the angle between the saw blade (6) and the ro-
tary table (14) is precisely 45°.
Re-tighten the lock nut (27a).
Subsequently check the position of the angle indicator. If
necessary, loosen the pointer (19) using a Philips screwdriv-
er, set to position 45° on the angle scale (18) and re-tighten
the retaining screw.
8.6 Mitre cut 0°- 45° and turntable 0° (fig.
1/2/11)
The crosscut, drag and mitre saw can be used to make mitre
cuts of 0° - 45° in relation to the work face.
Attention! For mitre cuts (inclined saw head), the left side of
the moveable stop rails (16a) must be fixed in the outer posi-
tion.
Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) outwards.
The moveable stop rail (16a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (16a) and the saw blade (6) amounts to a minimum
of 8 mm.
The right side of the moveable stop rails (16a) must be in
the inner positiion.
Before making a cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
Secure the set screw (16b) again.
Move the machine head (4) to the top position.
Fix the rotary table (14) in the 0° position.
Loosen the set screw (22) and use the handle (1) to angle
the machine head (4) to the left, until the pointer (19) indi-
cates the desired angle measurement on the scale (18).
Re-tighten the set screw (22).
Cut as described in section 8.3.
8.7 Mitre cut 0°- 45° and turntable 0°- 45° (fig.
2/4/12)
The crosscut, drag and mitre saw can be used to make mitre
cuts to the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 45° to the left or 0° - 45° to the right in
relation to the stop rail (double mitre cut).
10 GB
Attention! For mitre cuts (inclined saw head), the left side of
the moveable stop rails (16a) must be fixed in the outer position.
Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) outwards.
The moveable stop rail (16a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (16a) and the saw blade (6) amounts to a minimum
of 8 mm.
Before making a cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
Re-tighten the set screw (16b).
Move the machine head (4) to its upper position.
Release the rotary table (14) by loosening the handle (11).
Using the handle (11), set the rotary table (14) to the de-
sired angle (refer also to point 8.4 in this regard).
Re-tighten the handle (11) to secure the rotary table (14).
Undo the set screw (22).
Use the handle (1) to tilt the machine head (4) to the left until
it coincides with the required angle value (in this connection
see also section 8.6).
Re-tighten the set screw (22).
Cut as described under section 8.3.
8.8 Limiting the cutting depth (fig. 3/13)
The cutting depth can be infinitely adjusted using the screw
(24). To do this loosen the knurled nut (24a) on the screw
(24). Turn the screw (24) in or out to set the required cutting
depth. Then re-tighten the knurled nut (24a) on the screw
(24).
Check the setting by completing a test cut.
8.9 Sawdust bag (fig. 1/22)
The saw is equipped with a debris bag (17) for sawdust and chips.
Squeeze together the metal ring on the dust bag and attach it
to the outlet opening in the motor area.
The debris bag (17) can be emptied by means of a zipper at
the bottom.
Connection to an external dust extractor
For dust extraction, a vacuum hose can also be connected to
the dust extraction spout.
Connect the vacuum hose with the dust extraction spout.
The industrial vacuum cleaner must be suitable for the
material being worked.
When vacuuming dust that is especially detrimental to health
or carcinogenic, use a special vacuum cleaner.
8.10 Changing the saw blade (fig. 1/2/14-17)
Remove the power plug!
Important!
Wear safety gloves when changing the saw blade.
Risk of injury!
Swing the machine head (4) upwards and lock with the lock-
ing bolt (23).
Loosen the retaining screw (5a) of the cover using a Philips
screwdriver.
WARNING! Do not fully remove this screw.
Fold the saw blade guard (5) upwards until the saw blade
guard (5) is above the flange screw (28).
With one hand insert the Allen key (C) in the flange screw
(29).
Hold the Allen key (C) and slowly close the saw blade guard
(5) until it touches the Allen key (C).
Firmly press the saw shaft lock (30) and slowly rotate the
flange screw (28) in clockwise direction. The saw shaft lock
(30) engages after no more than one rotation.
Now, using a little more force, slacken the flange screw (29)
in the clockwise direction.
Turn the flange screw (28) right out and remove the outer
flange (29).
Take the blade (6) off the inner flange (31) and pull out
downwards.
Carefully clean the flange screw (28), outer flange (29) and
inner flange (32).
Fit and fasten the new saw blade (6) in reverse order.
Important! The cutting angle of the teeth, in other words the
direction of rotation of the saw blade (6) must coincide with
the direction of the arrow on the housing.
Before continuing your work make sure that all safety de-
vices are in good working condition.
Important! Every time that you change the saw blade (6),
check to see that it spins freely in the table insert (10) in both
perpendicular and 45° angle settings.
Important! The work to change and align the saw blade (6)
must be carried out correctly.
8.11 Using the laser (fig. 18)
To switch on: Press the ON/OFF switch laser (33) 1x. A
laser line is projected onto the material you wish to process,
providing an exact guide for the cut.
To switch off: Press again the ON/OFF switch laser (33).
8.12 Adjusting the laser (fig. 19-20)
If the laser (32) ceases to indicate the correct cutting line, you
can readjust the laser. To do so, open the screws (32b) and
remove the front cover (32a). Loosen the Philips head screws
(E) and set the laser by moving sideways until the laser beam
strikes the teeth of the saw blade (6).
After adjusting and tightening the laser, mount the front cover
by tightening both screws (32b) by hand.
9. Transport
Tighten the handle (11) to lock the rotary table.
Press the machine head (4) downwards and secure with the
locking bolt (23).
Fix the saw’s drag function with the locking screw for drag
guide (20) in rear position.
Carry the equipment by the fixed saw table (15).
When reassembling the equipment proceed as described
under section 7.
10. Maintenance
m Warning! Prior to any adjustment, maintenance or service
work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time using a
cloth. In order to extend the service life of the tool, oil the rotary
parts once monthly. Do not oil the motor.
When cleaning the plastic do not use corrosive products.
11GB
Cleaning the moving saw blade guard safety
device (5)
Always check the saw blade guard for debris before using the
machine.
Remove old sawdust and splinters using a brush or similar
tool.
Replacing the table insert
Danger!
With a damaged table insert (10) there is a risk of small
parts getting stuck between table insert and saw blade,
blocking the saw blade.
Immediately replace damaged table inserts!
1. Remove screws at table insert. If required, turn rotary table
and incline saw head to be able to reach the screws.
2. Remove table insert.
3. Install new table insert.
4. Tighten the screws at table insert.
Brush inspection
Check the carbon brushes after the first 50 operating hours
with a new machine, or when new brushes have been fitted.
After carrying out the first check, repeat the check every 10
operating hours.
If the carbon is worn to a length of 6 mm, or if the spring or
contact wire are burned or damaged, it is necessary to replace
both brushes. If the brushes are found to be usable following
removal, it is possible to reinstall them.
When servicing the carbon brushes, open the two latches coun-
terclockwise (as shown in Figure 21). Then remove the carbon
brushes.
Replace the carbon brushes in the reverse order.
11. Storage
Store the device and its accessories in a dark, dry and frost-
proof place that is inaccessible to children. The optimum stor-
age temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust and
moisture.
Store the operating manual with the electrical tool.
12. Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions.
The customer‘s mains connection as well as the ex-
tension cable used must also comply with these
regulations.
The product meets the requirements of EN 61000-3-11 and
is subject to special connection conditions. This means that
use of the product at any freely selectable connection point
is not allowed.
Given unfavourable conditions in the power supply the prod-
uct can cause the voltage to fluctuate temporarily.
The product is intended solely for use at connection points
that
a) do not exceed a maximum permitted supply impedance
“Z” (Zmax = 0.382 Ω), or
b) have a continuous current-carrying capacity of the mains
of at least 100 A per phase.
As the user, you are required to ensure, in consultation with
your electric power company if necessary, that the connec-
tion point at which you wish to operate the product meets
one of the two requirements, a) or b), named above.
Important information
In the event of an overloading the motor will switch itself
off. After a cool-down period (time varies) the motor can be
switched back on again.
Damaged electrical connection cable.
The insulation on electrical connection cables is often dam-
aged.
This may have the following causes:
Passage points, where connection cables are passed
through windows or doors.
Kinks where the connection cable has been improperly fas-
tened or routed.
Places where the connection cables have been cut due to
being driven over.
Insulation damage due to being ripped out of the wall out-
let.
Cracks due to the insulation ageing.
Such damaged electrical connection cables must not be used
and are life-threatening due to the insulation damage.
Check the electrical connection cables for damage regularly.
Make sure that the connection cable does not hang on the
power network during the inspection.
Electrical connection cables must comply with the applicable
VDE and DIN provisions. Only use connection cables with the
marking „H05VV-F“.
The printing of the type designation on the connection cable
is mandatory.
AC motor:
The mains voltage must be 220 - 240 V
~
.
Extension cables up to 25 m long must have a cross-section
of 1.5 mm
2
.
Connections and repairs of electrical equipment may only be
carried out by an electrician.
Please provide the following information in the event of any
enquiries:
Type of current for the motor
Machine data - type plate
13. Disposal and recycling
The equipment is supplied in packaging to prevent it from be-
ing damaged in transit. The raw materials in this packaging
can be reused or recycled. The equipment and its accesso-
ries are made of various types of material, such as metal and
plastic. Defective components must be disposed of as special
waste. Ask your dealer or your local council.
12 GB
The packaging is wholly composed of environment ally-friendly materials that can be disposed of at a local recycling
centre.
Contact your local refuse disposal authority for more details of how to dispose of your worn-out electrical devices.
Old devices must not be disposed of with household waste!
This symbol indicates that this product must not be disposed of together with domestic waste in compliance with the Directive
(2012/19/EU) pertaining to waste electrical and electronic equipment (WEEE). This product must be disposed of at a designat-
ed collection point. This can occur, for example, by handing it in at an authorised collecting point for the recycling of waste electri-
cal and electronic equipment. Improper handling of waste equipment may have negative consequences for the environment and
human health due to potentially hazardous substances that are often contained in electrical and electronic equipment. By properly
disposing of this product, you are also contributing to the effective use of natural resources. You can obtain information on collection
points for waste equipment from your municipal administration, public waste disposal authority, an authorised body for the disposal of
waste electrical and electronic equipment or your waste disposal company.
14. Troubleshooting
Fault Possible cause Remedy
Motor does not work Motor, cable or plug defective, fuses burnt Arrange for inspection of the machine by a specialist.
Never repair the motor yourself. Danger!
Check fuses and replace as necessary
The motor starts up slowly
and does not reach oper-
ating speed.
Voltage too low, coils damaged, capacitor burnt Contact the utility provider to check the voltage.
Arrange for inspection of the motor by a specialist. Ar-
range for replacement of the capacitor by a specialist
Motor makes excessive
noise
Coils damaged, motor defective Arrange for inspection of the motor by a specialist
The motor does not reach
its full power.
Circuits in the network are overloaded (lamps,
other motors, etc.)
Do not use any other equipment or motors on the same
circuit
Motor overheats easily. Overloading of the motor, insufficient cooling of
the motor
Avoid overloading the motor while cutting, remove dust
from the motor in order to ensure optimal cooling of the
motor
Saw cut is rough or wavy Saw blade dull, tooth shape not appropriate for
the material thickness
Re-sharpen saw blade and/or use suitable saw blade
Workpiece pulls away
and/or splinters
Excessive cutting pressure and/or saw blade not
suitable for use
Insert suitable saw blade
Service information
Please note that the following parts of this product are subject to normal or natural wear and that the following parts are therefore also required
for use as consumables.
Wear parts*: carbon brushes, saw blade, table inserts, sawdust bags
* Not necessarily included in the scope of delivery!
13GB
15. Warranty certificate
Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device
develops a fault, please contact our service department at the address shown on this guarantee card. Of course, if you would prefer to
call us then we are also happy to offer our assistance under the service number printed below. Please note the following terms under which
guarantee claims can be made:
These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights. We do not charge you for
this guarantee.
Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectification of these
defects or replacement of the device. Please note that our devices have not been designed for use in commercial, trade or industrial
applications. Consequently, the guarantee is invalidated if the equipment is used in commercial, trade or industrial applications or
for other equivalent activities. The following are also excluded from our guarantee: compensation for transport damage, damage
caused by failure to comply with the installation/assembly instructions or damage caused by unprofessional installation, failure to
comply with the operating instructions (e.g. connection to the wrong mains voltage or current type), misuse or inappropriate use
(such as overloading of the device or use of non-approved tools or accessories), failure to comply with the maintenance and safety
regulations, ingress of foreign bodies into the device (e.g. sand, stones or dust), effects of force or external influences (e.g. damage
caused by the device being dropped) and normal wear resulting from proper operation of the device.
The guarantee is rendered null and void if any attempt is made to tamper with the device.
The guarantee is valid for a period of 3 years starting from the purchase date of the device. Guarantee claims should be submitted
before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after
the end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or
parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no
new guarantee will become active for the work performed or parts fitted. This also applies when an on-site service is used.
In order to assert your guarantee claim, please send your defective device postage-free to the address shown below. Please enclose
either the original or a copy of your sales receipt or another dated proof of purchase. Please keep your sales receipt in a safe place,
as it is your proof of purchase. It would help us if you could describe the nature of the problem in as much detail as possible. If the
defect is covered by our guarantee then your device will either be repaired immediately and returned to you, or we will send you a
new device.
Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the scope of this guarantee or for
units which are no longer covered. To take advantage of this service, please send the device to our service address.
Service-Hotline (GB):
+800 4003 4003
(0,00 EUR/Min.)
Service-Email (GB):
Service Address (GB):
Forest Park & Garden
Coed Court, Taffsmead Road
Treforest, Ind. Estate, Pontypridd CF375SW
At www.lidl-service.com you can download this and many more manuals, product videos plus installation
software.
The QR code takes you directly to the Lidl service page (www.lidl-service.com) and you can open your
operating manual by entering the article number (IAN) 212188.
14 SE
Innehållsförteckning: Sida:
1. Inledning ............................................................................................................................................................................................................16
2. Apparatbeskrivning (ill. 1-22) .........................................................................................................................................................................16
3. Leveransomfång ................................................................................................................................................................................................16
4. Avsedd användning ..........................................................................................................................................................................................17
5. Säkerhetsanvisningar ........................................................................................................................................................................................17
6. Teknisk data .......................................................................................................................................................................................................20
7. Före idrifttagning ...............................................................................................................................................................................................21
8. Montering och manövrering .............................................................................................................................................................................21
9. Transport ............................................................................................................................................................................................................23
10. Underhåll ...........................................................................................................................................................................................................23
11. Förvaring ............................................................................................................................................................................................................24
13. Kassering och återvinning ................................................................................................................................................................................24
14. Felsökning ..........................................................................................................................................................................................................25
15. Garantibevis ......................................................................................................................................................................................................26
15SE
Förklaring av symbolerna apparaten
SE
Läs och följ anvisningarna i bruksanvisningen innan du börjar använda maskinen!
SE
Använd skyddsglasögon!
SE
Använd hörselskydd!
SE
Använd andningsskydd vid dammutveckling!
SE
Använd andningsskydd vid dammutveckling!
SE
Obs! Laserstrålning
SE
Skyddsklass II (dubbelisolering)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80

Parkside 312188 Operating And Safety Instructions Manual

Typ
Operating And Safety Instructions Manual
Ten podręcznik jest również odpowiedni dla

w innych językach