Parkside PKS 1700 B2 Instrukcja obsługi

Typ
Instrukcja obsługi
IAN 79729
K
SLIDING CROSS CUT MITRE SAW
Operation and Safety Notes
Original operating instructions
V
VLEČNA, ČELILNA IN ZAJERALNA
ŽAGA
Navodila za upravljanje in varnostna opozorila
Originalna navodila za uporabo
D
POKOSOVÁ PILA
Pokyny pro obsluhu a bezpečnostní pokyny
Originální návod k obsluze
W
DVOJRUČNÁ, SKRACOVACIA A PO-
KOSOVÁ PÍLA
Pokyny pre obsluhu a bezpečnostné pokyny
Originálny návod na obsluhu
T
PIŁA DWURĘCZNA, TARCZÓWKA, ZE
SKRĘTNĄ TARCZĄ
Wskazówki dotyczące obsługi i bezpieczeństwa
Instrukcją oryginalną
F A C
ZUG-, KAPP- UND GEHRUNGSSÄGE
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
V D
W T
SLIDING CROSS CUT MITRE SAW PKS 1700 B2
Anl_4300688.indb 1Anl_4300688.indb 1 10.10.12 18:4910.10.12 18:49
- 2 -
K
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
V
Pred branjem stran s slikami odprite navzven in se nato seznanite z vsemi funkcijami naprave.
D
Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.
W
Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.
T
Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z
wszystkimi funkcjami urządzenia.
F A C
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit
allen Funktionen des Gerätes vertraut.
GB Operation and Safety Notes Page 8
SI Navodila za upravljanje in varnostna opozorila Stran 23
CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 38
SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 53
PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 69
DE/AT/CH Bedienungs- und Sicherheitshinweise Seite 85
Anl_4300688.indb 2Anl_4300688.indb 2 10.10.12 18:4910.10.12 18:49
- 3 -
1
2
17
13 1214
2
35
18
26
3
3
4
5
6
8
7
9
10
11
1516109
19
20
8
21
22
118 c
22
23
18
1713
12 25
24 27
Anl_4300688.indb 3Anl_4300688.indb 3 10.10.12 18:4910.10.12 18:49
- 4 -
4 5
8 9
6 7
13
9 17 10
18
30
2329d
21
20
7
16
z
29
d
Anl_4300688.indb 4Anl_4300688.indb 4 10.10.12 18:4910.10.12 18:49
- 5 -
10 11
14 15
12 13
7
1
13
16
8
5
8
y 16
30
2
3
5
19
1617
8
8
5
15 16
16
5
Anl_4300688.indb 5Anl_4300688.indb 5 10.10.12 18:4910.10.12 18:49
- 6 -
16 17
20 21
18 19
27
6 31
36
34
28
32
c
38 7
35
Anl_4300688.indb 6Anl_4300688.indb 6 10.10.12 18:5010.10.12 18:50
- 7 -
22 23
36
33
37
Anl_4300688.indb 7Anl_4300688.indb 7 10.10.12 18:5010.10.12 18:50
GB
- 8 -
Table of contents
The reprinting or reproduction by any other means, in whole or in part, of documentation and papers
accompanying products is permitted only with the express consent of the iSC GmbH.
Subject to technical changes
1. Introduction ................................................................................................................................................10
2. Safety regulations .....................................................................................................................................10
3. Layout and items supplied ........................................................................................................................ 14
4. Intended use .............................................................................................................................................. 15
5. Technical data ........................................................................................................................................... 15
6. Before starting the equipment ..................................................................................................................16
7. Operation .................................................................................................................................................. 17
8. Replacing the power cable ...................................................................................................................... 19
9. Cleaning, maintenance and ordering of spare parts ............................................................................. 19
10. Storage ......................................................................................................................................................20
11. Disposal and recycling .............................................................................................................................20
12. Declaration of conformity ......................................................................................................................... 21
13. Warranty certifi cate ..................................................................................................................................22
Anl_4300688.indb 8Anl_4300688.indb 8 10.10.12 18:5010.10.12 18:50
GB
- 9 -
Caution - Read the operating instructions to reduce the risk of inquiry
Wear ear-muffs. The impact of noise can cause damage to hearing.
Wear safety goggles. Sparks generated during working or splinters, chips and dust emitted by the
device can cause loss of sight.
Wear a breathing mask. Dust which is injurious to health can be generated when working on wood
and other materials. Never use the device to work on any materials containing asbestos!
Important. Risk of injury. Never reach into the running saw blade.
Anl_4300688.indb 9Anl_4300688.indb 9 10.10.12 18:5010.10.12 18:50
GB
- 10 -
1. Introduction
Congratulations on your new purchase.
You have decided in favor of a high-quality pro-
duct. The operating instructions are a part of this
product. They contain information of importance
for your safety, for the use of the product and for
its disposal. Before you use the product, acquaint
yourself with all the information concerning its
operation and safety. Use the product only as
described and only for the listed areas of applica-
tion. If you hand on the product to other people,
give them all the documentation as well.
2. Safet y regulations
Caution!
Read all safety regulations and instruc-
tions.
Any errors made in following the safety regu-
lations and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instruc-
tions in a safe place for future use.
2.1 General safety information on electric
power tools
Warning! When using electric tools, basic
safety precautions should always be fol-
lowed to reduce the risk of fi re, electric
shock and personal injury, including
the following. Read all these instructions
before attempting to operate this product
and safe these instructions.
Keep work area clean
– Cluttered areas and benches invite injuries.
Consider work area environment
– Don‘t expose power tools to rain. Don‘t use
power tools in damp or wet locations. Keep
work area well lit. Don‘t use power tools in
presence of flammable liquids or gases.
Guard against electric shock
– Prevent body contact with grounded sur-
faces (e.g. pipes, radiators, ranges refrigera-
tiors).
Keep children away
– Do not let visitors contact tool or extension
cord. All visitors should be kept away from
work area.
Store idle tools
– When not is use, tools should be stored
in dry, high, or locked-up place, out of the
reach of children.
Don‘t force tool
– It will do the job better and safer at the rate
for which it was intended.
Use right tool
– Don‘t force small tools or attachments
to do the job of heavy duty tool. Don‘t use
tools for purposes not intended: for example,
don‘t use circular saw for cutt- ing tree limbs
or logs.
Dress properly
– Do not wear loose clothing or jewelry.
They can be caught in moving parts. Nonskid
footwear is recommended when working
outdoors. Wear protective hair covering to
contain long hair.
Use safety glasses
– Also use face or dust mask if cutting opera-
tion is dusty.
Don‘t abuse cord
– Never carry tool by cord or yank it to dis-
connect it from receptacle. Keep cord from
heat, oil and sharp edges.
Secure work
– Use clamps or a vise to hold work. It‘s safer
than using your hand and it frees both hands
to operate tool.
Don‘t overreach
– Keep proper footing and balance at all
times.
Maintain tools with care
– Keep tools sharp and clean for better and
safer performance. Follow instructions for
lubricating and changing accessories. Inspect
tool cords periodically and, if damaged, have
repaired by authorized service facility. Inspect
extension cords periodically and replace if
damaged. Keep handles dry, clean and free
from oil and grease.
Disconnect tools
– When not in use, before servicing, and
Anl_4300688.indb 10Anl_4300688.indb 10 10.10.12 18:5010.10.12 18:50
GB
- 11 -
when changing accessories such as blades,
bits and cutters.
Remove adjusting keys and wrenches
– Form the habit of checking to see that keys
and adjusting wrenches are removed from
tool before turning it on.
Avoid unintentional starting
– Don‘t carry plugged-in tool with finger on
switch. Be sure switch is off when plugging in.
Outdoor use extension cords
– When tool is used outdoors, use only exten-
sion cords intended for use outdoors and so
marked.
Stay alert
– Watch what you are doing. Use common
sense. Do not operate tool when you are
tired.
Check damaged parts
– Before further use of the tool, a guard or
other part that is damaged should be care-
fully checked to determine that it will operate
properly and perform its intended function.
Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting,
and any other conditions that may affect its
operation. A guard or other part that is dama-
ged should be properly repaired or replaced
by an authorized service center unless other-
wise indicated elsewhere in this instructions
manual. Have defective switches replaced by
an authorized service center. Do not use tool
if switch does not turn it on and off.
Warning
– The use of any other accessory or attach-
ment other than recommended it this ope-
rating instruction or the Einhell catalog may
present a risk of personal injury.
Have your tool repared by an expert
– This electric appliance is in accordance with
the relevant safety rules repairing of electric
appliances may be carried out only by ex-
perts otherwise it may cause considerable
danger for the user.
Connect the dust extraction device
Wherever there are facilities for fitting a dust
extraction system, make sure it is connected
and used.
2.2 Special safety information on the
equipment
1. Safety precautions
Change a worn out table insert.
Use only blades which are recommended by
the manufacturer and comply with EN 847-1.
If necessary, wear suitable personal protec-
tion equipment. This could consist of:
- Ear plugs to prevent the risk of damaging
your hearing
- A breathing mask to avoid the risk of inha-
ling hazardous dust
- Always wear gloves when handling saw
blades and rough materials. Whenever
practicable, saw blades must be carried in a
container.
The following can have an influence on dust
development:
- Worn, damaged or cracked saw blades
- Recommended capacity of the vacuum ext-
raction system: 20 m/s
- Proper guidance of the workpiece
Blades made of high-alloy high-speed steel
(HSS) must not be used.
2. Safety information on the laser
Important:
Laser radiation
Do not look into the beam Laser class 2
Protect yourself and your environment from ac-
cidents by taking the appropriate precautionary
measures.
Do not look directly into the laser beam with
the naked eye.
Never look directly into the laser path.
Never direct the laser beam at reflecting sur-
Anl_4300688.indb 11Anl_4300688.indb 11 10.10.12 18:5010.10.12 18:50
GB
- 12 -
faces, persons or animals. Even a low output
laser beam can inflict injury on the eye.
Caution: It is vital to follow the work proce-
dures described in these instructions. Using
the equipment in any other way may result in
hazardous exposure to laser radiation.
Never open laser module.
When the laser is not going to be used for an
extended period of time, the batteries should
be removed.
Never use an optical instrument (for example
magnifying glass) to view the laser beam.
Check the laser for damage on a regular ba-
sis and always before use. To protect yourself
against injury, never use the equipment if it is
damaged.
Defective lasers have to be repaired by a cus-
tomer service workshop.
3. Safety information on the batteries
Never recharge the batteries. Danger of ex-
plosion.
Keep batteries out of the reach of children. Do
not throw batteries into the fire, short-circuit or
take them apart.
If necessary clean the contacts on the batte-
ries and equipment before inserting the batte-
ries.
Remove flat batteries immediately from the
equipment. Risk of leakage!
Always replace all batteries in one go. Only
use new batteries of the same make.
Avoid contact with skin, eyes and mucous
membranes. If you come into contact with
battery acid, rinse the affected pars at once
with plenty of clear water and seek immediate
medical assistance.
Do not expose batteries to extreme condi-
tions, e.g. do not place on heaters or in direct
sunshine. Increased risk of leakage.
4. Maintenance and service
The following conditions can have an influ-
ence on noise impact on the operator:
- Type of saw blade (e.g. saw blades desig-
ned to reduce noise development)
- Material of the workpiece
- The force with which the workpiece is pu-
shed against the saw blade
Faults on the machine or its guards, safety de-
vices and blade must be reported to the per-
son in charge as soon as they are discovered.
5. Safe operation
Use a suitable blade for the material you wish
to saw.
Never use the drag, crosscut and miter saw
to cut any materials other than those specified
by the manufacturer.
Use only the transport devices to move the
equipment. Never use the guards for handling
or moving the equipment.
Use the saw only if it is in perfect condition
and properly maintained and only if the gu-
ards are correctly positioned.
When cutting miters, make sure that the de-
vice for swiveling the arm is fastened securely.
The floor around the machine must be level,
clean and free of loose particles, such as
chips and cutting residues.
The operator must receive proper training in
the use, adjustment and operation of the ma-
chine.
Only use properly sharpened saw blades. Do
not exceed the maximum speed specified on
the blade.
Be sure to only use spacers and spindle rings
specified by the manufacturer as suitable for
the intended purpose.
If the machine is equipped with a laser, this
laser may not be replaced by a different type
of laser. Repairs may only be carried out by
the manufacturer of the laser or one of his au-
thorized agents.
Do not remove any cutting residues or other
parts of workpieces from the cutting zone
while the machine is running and the saw unit
is not at rest.
Make sure that the machine is always secured
Anl_4300688.indb 12Anl_4300688.indb 12 10.10.12 18:5010.10.12 18:50
GB
- 13 -
on a workbench or a table if at all possible.
Support long workpieces (e.g. with a roller
table) to prevent them sagging at the end of a
cut.
6. Additional safety information on cros-
scut saws
Give these safety instructions to all persons
who work on the machine.
Do not use this saw to cut fire wood.
Caution! Hands and fingers may be injured
on the rotating saw blade.
Before you use the machine for the first time,
check that the voltage marked on the rating
plate is the same as your mains voltage.
If you need to use an extension cable, make
sure its conductor cross-section is big enough
for the saw’s power consumption. Minimum
cross-section: 1.5 mm
2
.
If you use a cable reel, the complete cable
must be pulled off the reel.
Persons working on the machine should not
be distracted.
Note the direction of rotation of the motor and
saw blade.
After you have switched off the motor, never
slow down the saw blade by applying pressu-
re to its side.
Only fit blades which are well sharpened and
have no cracks or deformations.
Faulty saw blades must be replaced immedia-
tely.
Never use saw blades which do not comply
with the data specified in this manual.
It is imperative to make sure that the arrow on
the saw blade conforms with the arrow on the
machine.
Pull out the power plug and twist the blade
with your hand into the 45° and 90° po-
sitions in order to make sure that the blade
does not touch the turntable in any position. If
necessary, readjust the saw head.
It is imperative to make sure that all devices
which cover the saw blade are in good wor-
king order.
Never wedge the hinged saw blade guard in
open position.
Never dismantle the machine’s safety devices
or render them inoperative.
Damaged or faulty safety devices have to be
replaced immediately.
Never cut workpieces which are too small to
hold securely in your hand.
Avoid placing your hands in hazardous posi-
tions in which, one or both hands could touch
the saw blade if they slip suddenly.
The saw must not to be used for cutting round
workpieces.
There must be no nails or other foreign bodies
in the part of the workpiece that you wish to
saw.
Always stand to the side of the saw blade
when working with the saw.
Never load the machine so much that it cuts
out.
Always press the workpiece firmly against the
workbench and the stop rail to prevent the
workpiece wobbling or twisting.
Ensure that the off-cuts can be removed to the
side of the saw blade. Otherwise it is possible
that they will be caught by the saw blade and
catapulted out of the machine.
Never saw more than one workpiece at any
one time.
Never remove loose splinters, chips or jam-
med pieces of wood when the saw blade is
running.
To rectify faults or remove jammed pieces of
wood, always switch off the machine first. -
Pull out the power plug-
Refit all guards and safety devices immedia-
tely after you have completed any repairs or
maintenance work.
Be sure to observe the safety information and
operating and maintenance instructions issued
by the manufacturer, as well as the dimensi-
ons listed in the Technical Data.
It is imperative to observe the accident pre-
vention regulations in force in your area as
well as all other generally recognized rules of
safety.
Operation in enclosed areas is permitted only
with a suitable vacuum extraction system.
The crosscut saw has to be connected to a
230 V socket-outlet with minimum fusing of 10
A.
Anl_4300688.indb 13Anl_4300688.indb 13 10.10.12 18:5010.10.12 18:50
GB
- 14 -
Do not use any low-powered machines for
heavy duty work.
Be careful when working in vertical mode.
Caution: Take extra care when making double
miter cuts!
Do not lose these safety instructions
3. Layout and items supplied
3.1 Layout
1. Handle
2. ON/OFF switch
3. Release lever
4. Saw shaft lock
5. Machine head
6. Movable blade guard
7. Saw blade
8. Clamping device
9. Workpiece support
10. Locking screw for workpiece support
11. Table insert
12. Latched position lever
13. Locking grip
14. Pointer
15. Scale
16. Turntable
17. Fixed saw table
18. Additional stability bar
19. Stop rail
20. Scale
21. Pointer
22. Sawdust bag
23. Locking screw
24. Locking screw for drag guide
25. Fastening bolt
26. Drag guide
27. Knurled screw for cutting depth limiter
28. Stop for cutting depth limiter
29. Adjustment screw (90°)
30. Adjustment screw (45°)
31. Flange bolt
32. Outer fl ange
33. Laser
34. ON/OFF switch for laser
35. Battery compartment
36. Battery compartment cover
37. Screw
38. Inner fl ange
c) Allen key, 6 mm
d) Counternut
y) 45° stop angle (not supplied)
z) 90° stop angle (not supplied)
3.2 Items supplied
Open the packaging and take out the equip-
ment with care.
Remove the packaging material and any
packaging and/or transportation braces (if
available).
Check to see if all items are supplied.
Inspect the equipment and accessories for
transport damage.
If possible, please keep the packaging until
the end of the guarantee period.
Important!
The equipment and packaging material
are not toys. Do not let children play with
plastic bags, foils or small parts. There is
a danger of swallowing or suffocating!
Drag, crosscut and miter Saw
2 x Clamping device (8)
2 x Workpiece support (9)
Sawdust bag (22)
Allen key, 5 mm
Allen key, 6 mm (c)
Additional stability bar (18)
2 x Battery (1.5 V LR03)
Anl_4300688.indb 14Anl_4300688.indb 14 10.10.12 18:5010.10.12 18:50
GB
- 15 -
4. Intended use
The drag, crosscut and miter saw is designed
to crosscut wood and plastic respective of the
machine’s size. The saw is not designed for cutting
rewood.
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufac-
turer will be liable for any damage or injuries of
any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
equipment is used in commercial, trade or indust-
rial businesses or for equivalent purposes.
The equipment is to be operated only with suitable
saw blades. It is prohibited to use any type of
cutting-off wheel.
To use the equipment properly you must also
observe the safety information, the assembly inst-
ructions and the operating instructions to be found
in this manual.
All persons who use and service the equipment
have to be acquainted with this manual and must
be informed about the equipment’s potential ha-
zards. It is also imperative to observe the accident
prevention regulations in force in your area. The
same applies for the general rules of health and
safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes. Even when the
equipment is used as prescribed it is still impossi-
ble to eliminate certain residual risk factors. The
following hazards may arise in connection with
the machine’s construction and design:
Contact with the saw blade in the uncovered
saw zone.
Reaching into the running saw blade (cut inju-
ries).
Kick-back of workpieces and parts of workpi-
eces.
Saw blade fracturing.
Catapulting of faulty carbide tips from the
saw blade.
Damage to hearing if ear-muffs are not used
as necessary.
Harmful emissions of wood dust when used in
closed rooms.
The product meets the requirements of EN
61000-3-11 and is subject to special con-
nection conditions. This means that use of the
product at any freely selectable connection
point is not allowed.
Given unfavorable conditions in the power
supply the product can cause the voltage to
fluctuate temporarily.
The product is exclusively intended for use
at connection points that have a continuous
current-carrying capacity of at least 100 A
per phase.
As the user, you are required to ensure, in
consultation with your electric power compa-
ny if necessary, that the connection point at
which you wish to operate the product meets
the specified requirements.
5. Technical data
AC motor: .........................................230V ~ 50Hz
Power: ........................................................ 1700 W
Operating mode: ................................................S1
Idle speed n
0
: ...................................... 4,800 min
-1
Carbide saw blade: ...........ø 210 x ø 30 x 2.8 mm
Number of teeth: ..................................................24
Swiveling range: ........................-45° / 0°/ +45°
Miter cut: ................................. 0° to 45° to the left
Saw width at 90°: ............................ 205 x 65 mm
Saw width at 45°: .............................140 x 65 mm
Saw width at 2 x 45°
(double miter cut): ..............................140 x 40 mm
Protection class: ..............................................II /
Weight: ..............................................approx. 15 kg
Laser class: ............................................................. 2
Wavelength of laser: .................................. 650 nm
Laser output: .................................................≤ 1mW
Laser module power
supply: ................................ 2 x 1.5 V Micro (AAA)
Anl_4300688.indb 15Anl_4300688.indb 15 10.10.12 18:5010.10.12 18:50
GB
- 16 -
Noise emission values
The saw’s noise is measured in accordance with
EN 61029.
Idle speed
L
pA
sound pressure level ....................... 88,6 dB(A)
K
pA
uncertainty .................................................3 dB
L
WA
sound power level .......................101,6 dB(A)
K
WA
uncertainty ................................................3 dB
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 61029.
Vibration emission value a
h
< 2.5 m/s
2
K uncertainty = 1.5 m/s
2
Warning!
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful effect.
Keep the noise emissions and vibrations
to a minimum.
Only use appliances which are in perfect
working order.
Service and clean the appliance regularly.
Adapt your working style to suit the appli-
ance.
Do not overload the appliance.
Have the appliance serviced whenever ne-
cessary.
Switch the appliance off when it is not in use.
6. Before starting the
equipment
6.1 General information
The equipment must be set up where it can
stand securely, i.e. it should be bolted to a
workbench, a universal base frame or similar.
All covers and safety devices have to be pro-
perly fitted before the equipment is switched
on.
It must be possible for the blade to run freely.
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws, etc.
Before you press the ON/OFF switch check
that the saw blade is fitted correctly. Moving
parts must run smoothly.
Before you connect the equipment to the po-
wer supply make sure the data on the rating
plate are identical to the mains data.
6.2 Assembling the saw (Fig. 1-2, 4-6)
To adjust the turntable (16), loosen the locking
grip (13) by approx. 2 turns and press the
latched position lever (12) to disengage the
turntable (16) (Figure 4).
To release the saw from its bottom position,
apply light downward pressure to the machi-
ne head (5). At the same time pull the safety
pin (25) out of the motor mount. Turn the
safety pin (25) through 90° so that the saw
remains unlocked (Fig. 1-2).
Swing the machine head (5) up until the re-
lease lever (3) latches into place (Fig. 1).
Fit the clamping devices (8) on the left and/or
right side of the fixed saw table (17) (Fig. 1).
Undo the locking screws for the workpiece
support (10) (Fig. 5).
Mount the workpiece support (9) on the fixed
saw table (17) and tighten the appropriate
locking screw (10) (Fig. 5).
Mount the second workpiece support (9) on
the opposite side of the saw and secure with
the appropriate locking screw (10).
When the locking screw (23) is loosened, you
can tilt the machine head (5) to the left by up
to 45° (Fig. 1-2).
Screw the additional stability bar (18) to the
Anl_4300688.indb 16Anl_4300688.indb 16 10.10.12 18:5010.10.12 18:50
GB
- 17 -
r
back of the equipment (Fig. 6).
6.3 Precision adjustment of the stop for
crosscut 90° (Fig. 7-8)
No stop angle included.
Fasten the turntable (16) in 0° position.
Undo the locking screw (23) and move the
machine head (5) all the way to the right
using the handle (1).
Place the 90° angular stop (z) between the
blade (7) and the turntable (16).
Slacken the counternut (d). Adjust the ad-
justment screw (90°) (29) until the angle
between the blade (7) and the turntable (16)
equals 90°.
Retighten the counternut (d) to secure this set-
ting.
Check the position of the pointer (21) on the
scale (20). If necessary, release the pointer
(21) with a crosstip screwdriver, move to the
0° position of the scale (20) and retighten.
6.4 Precision adjustment of the stop for
miter cut 45° (Fig. 1, 7, 10-11)
No stop angle included.
Fasten the turntable (16) in 0° position.
Undo the locking screw (23) and move the
machine head (5) all the way to the left using
the handle, until it coincides at 45°.
Place the 45° stop angle (y) between the bla-
de (7) and the turntable (16).
Adjust the adjustment screw (30) so that the
angle between the blade (7) and the turntab-
le (16) equals exactly 45°.
7. Operation
7.1 Cross cut 90° and turntable 0°
(Fig. 1-3, 12)
Important! The integral resetting springs will
automatically lift the machine head. Do not simply
let go of the handle (1) after cutting, but allow the
machine head (5) to rise slowly, applying slight
counter pressure as it does so.
For cutting widths up to approx. 100 mm it is
possible to fi x the saw’s drag function with the
locking screw for drag guide (24) in rear position.
If the cutting width exceeds 100 mm you must
ensure that the locking screw for drag guide (24)
is slackened and that the machine head (5) can
be moved.
Move the machine head (5) to its upper posi-
tion.
Use the handle (1) to push back the machine
head (5) and fix it in this position if required
(dependent on the cutting width).
Place the piece of wood to be cut at the stop
rail (19) and on the turntable (16).
Lock the material with the clamping device
(8) on the fixed saw table (17) to prevent the
material from moving during the cutting ope-
ration.
Push down the release lever (3) to release the
machine head (5).
Press the ON/OFF switch (2) to start the mo-
tor.
With the drag guide (26) fixed in place: use
the handle (1) to move the machine head (5)
steadily and with light pressure downwards
until the saw blade (7) has completely cut
through the workpiece.
With the drag guide (26) not fixed in place:
pull the machine head (5) all the way to the
front. Lower the handle (1) to the very bottom
by applying steady and light downward
pressure. Now push the machine head (5)
slowly and steadily to the very back until the
saw blade (7) has completely cut through the
workpiece.
When the cutting operation is completed,
move the machine head (5) back to its upper
(home) position and release the ON/OFF
Anl_4300688.indb 17Anl_4300688.indb 17 10.10.12 18:5010.10.12 18:50
GB
- 18 -
button (2).
7.2 Cross cut 90° and turntable 0° - 45°
(Fig. 1-3, 13)
The crosscut saw can be used to make crosscuts
of 0° -45° to the left and 0° -45° to the right in
relation to the stop rail.
Release the turntable (16) by slackening the
locking grip (13).
Press the latched position lever (12). Turn the
turntable (16) and scale pointer (14) to the
desired angular setting on the scales (15) and
lock into place with the locking grip (13). The
saw has locking positions at angles of - 45°,
-30°, -22.5°, -15°, 0°, 15°, 22.5°, 30°
and 45°, at which you can engage latched
position lever (12).
Cut as described under section 7.1.
7.3 Miter cut 0°- 45° and turntable 0°
(Fig. 1-3, 14)
The crosscut saw can be used to make miter cuts
of 0° - 45° in relation to the work face.
If required, dismantle the clamping device (8)
or mount on the opposite side of the fixed saw
table (17).
Move the machine head (5) to its upper posi-
tion.
Fasten the turntable (16) in 0° position.
Undo the locking screw (23). Use the handle
(1) to tilt the machine head (5) to the left until
the pointer (21) points to the required angle
on the scale (20).
Re-tighten the fixing screw (23).
Cut as described in section 7.1.
7.4 Miter cut 0°- 45° and turntable 0°-
45° (Fig. 1-3, 15)
The crosscut saw can be used to make miter cuts
to the left of 0°- 45° in relation to the work face
and, at the same time, 0° - 45° to the left or 0° -
45° to the right in relation to the stop rail (double
miter cut).
If required, dismantle the clamping device (8)
or mount on the opposite side of the fixed saw
table (17).
Move the machine head (5) to its upper posi-
tion.
Release the turntable (16) by slackening the
locking grip (13).
Press the latched position lever (12). Turn the
turntable (16) and scale pointer (14) to the
desired angular setting on the scales (15) and
lock into place with the locking grip (13).
Undo the locking screw (23) and use the
handle (1) to tilt the machine head (5) to the
left until it coincides with the required angle
value (in this connection see also section 7.3).
Re-tighten the fixing screw (23).
Cut as described under section 7.1.
7.5 Limiting the cutting depth (Fig. 16)
The cutting depth can be infinitely adjusted
using the screw (27). To do this loosen the
knurled nut on the screw (27). Move the stop
for the cutting depth limiter (28) to the outside.
Turn the screw (27) in or out to set the requi-
red cutting depth. Then re-tighten the knurled
nut on the screw (27).
Check the setting by completing a test cut.
7.6 Sawdust bag (Fig. 2)
The saw is equipped with a debris bag (22) for
sawdust and chips.
The debris bag (22) can be emptied by means of
a zipper at the bottom.
7.7 Changing the saw blade
(Fig. 1, 17-20)
Remove the power plug!
Important.
Wear safety gloves when changing the
saw blade. Risk of injury.
Swing up the machine head (5). Use the sa-
fety pin (25) to lock the machine head in this
position.
Press the release lever (3). Swing up the saw
blade guard (6) to the point where the recess
in the saw blade guard (6) is above the flan-
ge bolt (31).
Press the saw shaft lock (4) with one hand.
With the other hand insert the Allen key (c) in
the flange bolt (31).
Firmly press the saw shaft lock (4) and slowly
rotate the flange bolt (31) in clockwise direc-
tion. The saw shaft lock (4) engages after no
Anl_4300688.indb 18Anl_4300688.indb 18 10.10.12 18:5010.10.12 18:50
GB
- 19 -
more than one rotation.
Now, using a little more force, slacken the
flange bolt (31) in the clockwise direction.
Turn the flange screw (31) right out and remo-
ve the external flange (32).
Take the blade (7) off the inner flange (38)
and pull out downwards.
Carefully clean the flange screw (31), outer
flange (32) and inner flange (38).
Fit and fasten the new saw blade (7) in rever-
se order.
Important! The cutting angle of the teeth,
in other words the direction of rotation of the
saw blade (7) must coincide with the direction
of the arrow on the housing.
Before continuing your work make sure that
all safety devices are in good working condi-
tion.
Important! Every time that you change the
saw blade (7), check to see that it spins freely
in the table insert (11) in both perpendicular
and 45° angle settings.
Important! The work to change and align
the saw blade (7) must be carried out correct-
ly.
7.8 Transport (Fig. 1-3)
Retighten the locking grip (13) to secure the
turntable (16) in place.
Activate the release lever (3), press the ma-
chine head (5) downwards and secure with
the safety pin (25). The saw is now locked in
its bottom position.
Fix the saw’s drag function with the locking
screw for drag guide (24) in rear position.
Carry the equipment by the fixed saw table
(17).
When reassembling the equipment proceed
as described under section 6.2.
7.9 Using the laser (Fig. 21-23/Item 33)
To switch on: Move the ON/OFF switch
of the laser (34) to the “1” position. A laser
line is projected onto the material you wish to
process, providing an exact guide for the cut.
To switch off: Move the ON/OFF switch of
the laser (34) to the “0” position.
Setting the laser: The laser is adjusted with
the screw (37) and glued in place ex-works.
Further adjustment of the laser during operati-
on is not required. Important. Do not look into
the laser beam.
Replacing the battery: Switch off the
laser (33). Remove the battery compartment
cover (36). Remove the batteries and replace
with new batteries (2 x 1.5 Volt Type R03, LR
03 Micro, AAA) Check that the battery termi-
nals are positioned correctly when inserting
new batteries. Close the battery compartment
(35) again.
8. Replacing the power cable
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel to
avoid danger.
9. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before star-
ting any cleaning work.
9.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the device
immediately each time you have finished
using it.
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use cleaning
agents or solvents; these could attack the
plastic parts of the equipment. Ensure that no
water can seep into the device.
Anl_4300688.indb 19Anl_4300688.indb 19 10.10.12 18:5010.10.12 18:50
GB
- 20 -
9.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician.
Important! The carbon brushes should not be rep
laced by anyone but a qualifi ed electrician.
9.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
9.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
For our latest prices and information please go to
www.isc-gmbh.info
10. Storage
Store the equipment and accessories out of
children’s reach in a dark and dry place at above
freezing temperature. The ideal storage tempe-
rature is between 5 and 30 °C. Store the electric
tool in its original packaging.
11. Disposal and recycling
The unit is supplied in packaging to prevent its
being damaged in transit. This packaging is raw
material and can therefore be reused or can be
returned to the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic. De-
fective components must be disposed of as spe-
cial waste. Ask your dealer or your local council.
Disposing of batteries:
Batteries contain materials that are potentially
harmful to the environment. Never place batteries
in your household refuse, in fi re or in water. Bat-
teries should be collected, recycled or disposed
of by environment-friendly means. Send your
old batteries to iSC GmbH, Eschenstrasse 6 in
D-94405 Landau. You can then be sure that the
equipment will be correctly disposed of by the
manufacturer.
For EU countries only
Never place any electric power tools in your
household refuse.
To comply with European Directive 2002/96/EC
concerning old electric and electronic equipment
and its implementation in national laws, old elec-
tric power tools have to be separated from other
waste and disposed of in an environment-friendly
fashion, e.g. by taking to a recycling depot.
Recycling alternative to the return request:
As an alternative to returning the equipment to the
manufacturer, the owner of the electrical equip-
ment must make sure that the equipment is proper-
ly disposed of if he no longer wants to keep the
equipment. The old equipment can be returned to
a suitable collection point that will dispose of the
equipment in accordance with the national recyc-
ling and waste disposal regulations. This does not
apply to any accessories or aids without electrical
components supplied with the old equipment.
Anl_4300688.indb 20Anl_4300688.indb 20 10.10.12 18:5010.10.12 18:50
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102

Parkside PKS 1700 B2 Instrukcja obsługi

Typ
Instrukcja obsługi

w innych językach