Parkside 331932_1907 Operating And Safety Instructions Manual

Marka: Parkside

Model: 331932_1907

Typ: Operating And Safety Instructions Manual

Ten podręcznik jest również odpowiedni dla

PZKS 2000 B2

IAN 331932_1907

CHAT

KAPP- UND ZUGSÄGE

Bedienungs- und Sicherheitshinweise

Originalbetriebsanleitung

SLIDING COMPOUND MITRE SAW PZKS 2000 B2

SKERSINIO IR IŠILGINIO PJOVIMO STAKLĖS

Nurodymai dėl valdymo ir saugumo

Originalios naudojimo instrukcijos vertimas

SLIDING COMPOUND MITRE SAW

Operating and Safety Instructions

Translation of Original Operating Manual

TARCZÓWKA I PIŁA DWURĘCZNA

Wskazówki dotyczące obsługi i bezpieczeństwa

Tłumaczenie oryginalnej instrukcji obsługi

LTPL

GB Operating and Safety Instructions Page 01

PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 15

LT Nurodymai dėl valdymo ir saugumo Puslapis 30

DE / AT / CH Bedienungs- und Sicherheitshinweise Seite 44

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi funkcjami urządzenia.

Prieš skaitydami išlankstykite lapa su paveiksleliais ir susipažinkite su visomis prietaiso funkcijomis.

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen Funktionen des Gerätes vertraut.

DE AT CH

27a

26a

12131415

16b

16a

1918

7a7a

24a

A A

B B

C C

D D

E E

F F

G G

H H

I I

J J

K K

L L

IAN 331932_1907

Kapp- und Zugsäge

Mitre saw

Scie à onglet mixtes

220 - 240 V

50 Hz | 4800 min

-1

S1 1700 W / S6 25% 2000 W

Ø 210 mm x Ø 30 mm x 2.6 mm

manufactured: 07/2019

S.Nr.:

PZKS 2000 B2

6 7

988

1918

16a

max. 8 mm

24a

max. 8 mm

A A

B B

C C

D D

E E

F F

G G

H H

I I

J J

K K

L L

IAN 331932_1907

Kapp- und Zugsäge

Mitre saw

Scie à onglet mixtes

220 - 240 V

50 Hz | 4800 min

-1

S1 1700 W / S6 25% 2000 W

Ø 210 mm x Ø 30 mm x 2.6 mm

manufactured: 07/2019

S.Nr.:

PZKS 2000 B2

A A

B B

C C

D D

E E

F F

G G

H H

I I

J J

K K

L L

IAN 331932_1907

Kapp- und Zugsäge

Mitre saw

Scie à onglet mixtes

220 - 240 V

50 Hz | 4800 min

-1

S1 1700 W / S6 25% 2000 W

Ø 210 mm x Ø 30 mm x 2.6 mm

manufactured: 07/2019

S.Nr.:

PZKS 2000 B2

A A

B B

C C

D D

E E

F F

G G

H H

I I

J J

K K

L L

17 18

21 22

32a

32b

DRÜCKEN

PUSH

1GB

Table of contents: Page:

1. Explanation of the symbols on the equipment ..................................................................................................................................................2

2. Introduction ..........................................................................................................................................................................................................3

3. Device description (fig. 1-22) .............................................................................................................................................................................3

4. Scope of delivery ................................................................................................................................................................................................4

5. Intended use ........................................................................................................................................................................................................ 4

6. Safety information ............................................................................................................................................................................................... 4

7. Technical data ..................................................................................................................................................................................................... 7

8. Before starting the equipment ............................................................................................................................................................................8

9. Attachment ...........................................................................................................................................................................................................8

10. Operation ............................................................................................................................................................................................................ 9

11. Maintenance .....................................................................................................................................................................................................10

12. Transport ............................................................................................................................................................................................................11

13. Storage ..............................................................................................................................................................................................................11

14. Electrical connection .........................................................................................................................................................................................11

15. Disposal and recycling .....................................................................................................................................................................................12

16. Troubleshooting .................................................................................................................................................................................................13

17. Warranty certificate ..........................................................................................................................................................................................14

18. Declaration of conformity .................................................................................................................................................................................59

2 GB

1. Explanation of the symbols on the equipment

Before commissioning, read and observe the operating instructions and safety instructions!

Wear safety goggles!

Wear ear-muﬀs!

Wear a breathing mask!

Important! Risk of injury. Never reach into the running saw blade!

Important! Laser radiation

Protection Class II (double shielded)

3GB

2. Introduction

MANUFACTURER:

scheppach

Fabrikation von Holzbearbeitungsmaschinen GmbH

Günzburger Straße 69

D-89335 Ichenhausen

DEAR CUSTOMER,

We hope your new tool brings you much enjoyment and suc-

cess.

NOTE:

According to the applicable product liability laws, the manu-

facturer of the device does not assume liability for damages

to the product or damages caused by the product that occurs

due to:

• Improper handling,

• Non-compliance of the operating instructions,

• Repairs by third parties, not by authorized service techni-

cians,

• Installation and replacement of non-original spare parts,

• Application other than speciﬁed,

• A breakdown of the electrical system that occurs due to the

non-compliance of the electric regulations and VDE regula-

tions 0100, DIN 57113 / VDE0113.

We recommend:

Read through the complete text in the operating instructions be-

fore installing and commissioning the device.

The operating instructions are intended to help the user to be-

come familiar with the machine and take advantage of its ap-

plication possibilities in accordance with the recommendations.

The operating instructions contain important information on

how to operate the machine safely, professionally and econom-

ically, how to avoid danger, costly repairs, reduce downtimes

and how to increase reliability and service life of the machine.

In addition to the safety regulations in the operating instruc-

tions, you have to meet the applicable regulations that apply

for the operation of the machine in your country.

Keep the operating instructions package with the machine at

all times and store it in a plastic cover to protect it from dirt and

moisture. Read the instruction manual each time before operat-

ing the machine and carefully follow its information.

The machine can only be operated by persons who were in-

structed concerning the operation of the machine and who are

informed about the associated dangers. The minimum age re-

quirement must be complied with.

In addition to the safety instructions contained in this operating

manual and the speciﬁc regulations of your country, the techni-

cal rules generally accepted for the operation of machines of

the same type must be observed.

We accept no liability for damage or accidents which arise

due to non-observance of these instructions and the safety in-

formation.

3. Device description (ﬁg. 1-22)

1. Handle

2. ON/OFF switch

3. Lock switch

4. Machine head

5. Moving saw blade guard

5a. Locking screw

6. Saw blade

7. Clamping device

7a. Star-grip screw

8. Workpiece support

9. Set screw for workpiece support

10. Table insert

11. Handle / Set screw for rotary table

12. Pointer

13. Scale

14. Rotary table

15. Fixed saw table

16. Stop rail

16a. Movable stop rail

16b. Set screw

17. Sawdust bag

18. Angle screw

19. Angle indicator

20. Set screw for drag guide

21. Drag guide

22. Set screw

23. Locking bolt

24. Screw for cutting depth limiting

24a. Knurled nut for cutting depth limiting

25. Stop for cutting depth limiting

26. Adjusting screw (90°)

26a. Lock nut (90°)

27. Adjusting screw (45°)

27a. Lock nut (45°)

28. Flange screw

29. Outer ﬂange

30. Saw shaft lock

31. Inner ﬂange

32. Laser

32a. Laser housing cover

32b. Philips screw

33. ON/OFF switch laser

34. Guide bracket

35. Latched position lever

36. Tilt protection

37. Length stop

38. Adjustment screw

A.) 90° stop angle (not supplied)

B.) 45° stop angle (not supplied)

C.) Allen key, 6 mm

D.) Allen key, 3 mm

E.) Philips head screw (Laser)

4 GB

4. Scope of delivery

• Crosscut, drag and mitre saw

• 2 x Clamping device (7)

• 2 x Workpiece support (8) (preassembled)

• Sawdust bag (17)

• Allen key 6 mm (C)

• Allen key 3 mm (D)

• Operating manual

5. Intended use

The crosscut, drag and mitre saw is designed to crosscut wood

and plastic respective of the machine’s size. The saw is not de-

signed for cutting ﬁrewood.

Warning!

Do not use the saw to cut materials other than those speciﬁed

described in manual.

Warning!

The supplied saw blade is only intended for the sawing of

wood! Do not use this blade for the sawing of ﬁrewood!

The equipment is to be used only for its prescribed purpose.

Any other use is deemed to be a case of misuse. The user / op-

erator and not the manufacturer will be liable for any damage

or injuries of any kind caused as a result of this.

The equipment is to be operated only with suitable saw blades.

It is prohibited to use any type of cutting-oﬀ wheel.

To use the equipment properly you must also observe the safety

information, the assembly instructions and the operating instruc-

tions to be found in this manual.

All persons who use and service the equipment have to be

acquainted with this manual and must be informed about the

equipment’s potential hazards.

It is also imperative to observe the accident prevention regula-

tions in force in your area.

The same applies for the general rules of health and safety at

work.

The manufacturer will not be liable for any changes made to the

equipment nor for any damage resulting from such changes.

Even when the equipment is used as prescribed it is still im-

possible to eliminate certain residual risk factors. The following

hazards may arise in connection with the machine’s construc-

tion and design:

• Contact with the saw blade in the uncovered saw zone.

• Reaching into the running saw blade (cut injuries).

• Kick-back of workpieces and parts of workpieces.

• Saw blade fracturing.

• Catapulting of faulty carbide tips from the saw blade.

• Damage to hearing if ear-muﬀs are not used as necessary.

• Harmful emissions of wood dust when used in closed rooms.

Please note that our equipment has not been designed for use

in commercial, trade or industrial applications. Our warranty

will be voided if the equipment is used in commercial, trade or

industrial businesses or for equivalent purposes.

6. Safety information

General power tool safety warnings

m WARNING! Read all safety warnings, instruc-

tions, illustrations and speciﬁcations provided with

this power tool. Failure to follow all instructions listed below

may result in electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future refer-

ence.

The term “power tool” in the warnings refers to your mains-operat-

ed (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive at-

mospheres, such as in the presence of ﬂamma-

ble liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

• Keep children and bystanders away while op-

erating a power tool. Distractions can cause you to

lose control.

2. Electrical safety

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁed plugs and matching outlets will reduce

risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet con-

ditions. Water entering a power tool will increase the

risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

• If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces the

risk of electric shock.

3. Personal safety

• Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inﬂuence of drugs, alcohol or medi-

cation. A moment of inattention while operating power

tools may result in serious personal injury.

5GB

• Use personal protective equipment. Always

wear eye protection. Protective equipment such as

a dust mask, non-skid safety shoes, hard hat or hearing

protection used for appropriate conditions will reduce

personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your ﬁnger on the switch or energising power tools that

have the switch on invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in

personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control of the

power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

• Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

4. Power tool use and care

• Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was de-

signed.

• Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that cannot

be controlled with the switch is dangerous and must be

repaired.

• Disconnect the plug from the power source

and/or remove the battery pack, if detach-

able, from the power tool before making any

adjustments, changing accessories, or storing

power tools. Such preventive safety measures reduce

the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to oper-

ate the power tool. Power tools are dangerous in the

hands of untrained users.

• Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀect the power tool’s operation. If

damaged, have the power tool repaired be-

fore use. Many accidents are caused by poorly main-

tained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

for operations diﬀerent from those intended could result in

a hazardous situation.

• Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles

and grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

5. Service

• Have your power tool serviced by a qualiﬁed

repair person using only identical replacement

parts. This will ensure that the safety of the power tool

is maintained.

Safety instructions for mitre saws

a) Mitre saws are intended to cut wood or wood-

like products, they cannot be used with abrasive

cut-oﬀ wheels for cutting ferrous material such as

bars, rods, studs, etc. Abrasive dust causes moving parts

such as the lower guard to jam. Sparks from abrasive cutting

will burn the lower guard, the kerf insert and other plastic parts.

b) Use clamps to support the workpiece when-

ever possible. If supporting the workpiece by

hand, you must always keep your hand at least

100 mm from either side of the saw blade. Do

not use this saw to cut pieces that are too small

to be securely clamped or held by hand. If your

hand is placed too close to the saw blade, there is an

increased risk of injury from blade contact.

c) The workpiece must be stationary and clamped

or held against both the fence and the table.

Do not feed the workpiece into the blade or

cut “freehand” in any way. Unrestrained or moving

workpieces could be thrown at high speeds, causing injury.

d) Push the saw through the workpiece. Do not pull

the saw through the workpiece. To make a cut,

raise the saw head and pull it out over the work-

piece without cutting, start the motor, press the

saw head down and push the saw through the

workpiece. Cutting on the pull stroke is likely to cause the

saw blade to climb on top of the workpiece and violently

throw the blade assembly towards the operator.

e) Never cross your hand over the intended line

of cutting either in front or behind the saw

blade. Supporting the workpiece “cross handed” i.e.

holding the workpiece to the right of the saw blade with

your left hand or vice versa is very dangerous.

f) Do not reach behind the fence with either hand

closer than 100 mm from either side of the saw

blade, to remove wood scraps, or for any oth-

er reason while the blade is spinning. The prox-

imity of the spinning saw blade to your hand may not be

obvious and you may be seriously injured.

6 GB

g) Inspect your workpiece before cutting. If the

workpiece is bowed or warped, clamp it with

the outside bowed face toward the fence. Al-

ways make certain that there is no gap be-

tween the workpiece, fence and table along

the line of the cut. Bent or warped workpieces can

twist or shift and may cause binding on the spinning saw

blade while cutting. There should be no nails or foreign

objects in the workpiece.

h) Do not use the saw until the table is clear of all

tools, wood scraps, etc., except for the work-

piece. Small debris or loose pieces of wood or other

objects that contact the revolving blade can be thrown

with high speed.

i) Cut only one workpiece at a time. Stacked multi-

ple workpieces cannot be adequately clamped or braced

and may bind on the blade or shift during cutting.

j) Ensure the mitre saw is mounted or placed on

a level, ﬁrm work surface before use. A level and

ﬁrm work surface reduces the risk of the mitre saw becom-

ing unstable.

k) Plan your work. Every time you change the bev-

el or mitre angle setting, make sure the adjust-

able fence is set correctly to support the work-

piece and will not interfere with the blade or

the guarding system. Without turning the tool “ON”

and with no workpiece on the table, move the saw blade

through a complete simulated cut to assure there will be no

interference or danger of cutting the fence.

l) Provide adequate support such as table exten-

sions, saw horses, etc. for a workpiece that is

wider or longer than the table top. Workpieces

longer or wider than the mitre saw table can tip if not

securely supported. If the cut-oﬀ piece or workpiece tips,

it can lift the lower guard or be thrown by the spinning

blade.

m) Do not use another person as a substitute for

a table extension or as additional support. Un-

stable support for the workpiece can cause the blade to

bind or the workpiece to shift during the cutting operation

pulling you and the helper into the spinning blade.

n) The cut-oﬀ piece must not be jammed or

pressed by any means against the spinning

saw blade. If conﬁned, i.e. using length stops, the cut-

oﬀ piece could get wedged against the blade and thrown

violently.

o) Always use a clamp or a ﬁxture designed to

properly support round material such as rods

or tubing. Rods have a tendency to roll while being cut,

causing the blade to “bite” and pull the work with your

hand into the blade.

p) Let the blade reach full speed before contact-

ing the workpiece. This will reduce the risk of the

workpiece being thrown.

q) If the workpiece or blade becomes jammed,

turn the mitre saw oﬀ. Wait for all moving

parts to stop and disconnect the plug from

the power source and/or remove the battery

pack. Then work to free the jammed material.

Continued sawing with a jammed workpiece could cause

loss of control or damage to the mitre saw.

r) After ﬁnishing the cut, release the switch, hold

the saw head down and wait for the blade to

stop before removing the cut-oﬀ piece. Reaching

with your hand near the coasting blade is dangerous.

s) Hold the handle ﬁrmly when making an incom-

plete cut or when releasing the switch before

the saw head is completely in the down posi-

tion. The braking action of the saw may cause the saw

head to be suddenly pulled downward, causing a risk of

injury.

Safety Instructions for the handling of saw blades

1. Do not use damaged or deformed saw blades.

2. Do not use any insertion tools with cracks. Sort out cracked

insertion tools. Repairs are not permitted.

3. Do not use saw blades made of high speed steel.

4. Check the condition of the saw blades before using the

crosscut, drag and mitre saw.

5. Make sure that a suitable saw blade for the material to

be cut is selected.

6. Only use saw blades recommended by the manufacturer.

Saw blades designed to cut wood and similar materials

must comply with EN 847-1.

7. Do not use saw blades made of high-speed alloy steel

(HSS steel).

8. Only use saw blades for which the maximum permissible

speed is not lower than the maximum spindle speed of the

crosscut, drag and mitre saw and which are suitable for

the material to be cut.

9. Observe the saw blade direction of rotation.

10. Only insertion the saw blade if you have mastered their

use.

11. Observe the maximum speed. The maximum speed speci-

ﬁed on the insertion tool may not be exceeded. If speci-

ﬁed, observe the speed range.

12. Clean grease, oil and water oﬀ of the clamping surfaces.

13. Do not use any loose reducing rings or bushes for the re-

ducing of holes on saw blades.

14. Make sure that ﬁxed reducer rings for securing the inser-

tion tool have the same diameter and have at least 1/3 of

the cutting diameter.

15. Make sure that ﬁxed reducer rings are parallel to each

other.

16. Handle insertion tool with caution. They are ideally stored

in the originally package or special containers. Wear

protective gloves in order to improve grip and to further

reduce the risk of injury.

17. Prior to the use of insertion tools, make sure that all protec-

tive devices are properly fastened.

18. Prior to use, make sure that the insertion tool meets the

technical requirements of this electric tool and is properly

fastened.

19. Only use the supplied saw blade for cutting wood, never

for the processing of metals.

20. Only use saw blade diameters in accordance with the

markings on the saw.

21. Use additional workpiece supports, if required for work-

piece stability.

22. Workpiece support extensions must always be secured

and used during work.

7GB

23. Replace table inserts when worn!

24. Avoid overheating of the saw teeth.

25. When sawing plastic, avoid melting of the plastic.

Use the appropriate saw blades for this purpose. Replace

damaged or worn saw blades immediately.

When the saw blade overheats, stop the machine. Allow

the saw blade to cool down before using the machine

again.

Attention: Laser radiation

Do not stare into the beam

Class 2 laser

Protect yourself and you environment from acci-

dents using suitable precautionary measures!

• Do not look directly into the laser beam with unprotected

eyes.

• Never look into the path of the beam.

• Never point the laser beam towards reﬂecting surfaces and

persons or animals. Even a laser beam with a low output can

cause damage to the eyes.

• Caution - methods other than those speciﬁed here can result

in dangerous radiation exposure.

• Never open the laser module. Unexpected exposure to the

beam can occur.

• The laser may not be replaced with a diﬀerent type of laser.

• Repairs of the laser may only be carried out by the laser

manufacturer or an authorised representative.

Residual risks

The machine has been built according to the state

of the art and the recognised technical safety re-

quirements. However, individual residual risks can

arise during operation.

• Health hazard due to electrical power, with the use of im-

proper electrical connection cables.

• Furthermore, despite all precautions having been met, some

non-obvious residual risks may still remain.

• Residual risks can be minimised if the „Safety information“

and the „Proper use“ are observed along with the whole of

the operating instructions.

• Do not load the machine unnecessarily: excessive pressure

when sawing will quickly damage the saw blade, which re-

sults in reduced output of the machine in the processing and

in cut precision.

• When cutting plastic material, please always use clamps:

the parts which should be cut must always be ﬁxed between

the clamps.

• Avoid accidental starting of the machine: the operating but-

ton may not be pressed when inserting the plug in an outlet.

• Use the tool that is recommended in this manual. In doing so,

your machine provides optimal performance.

• Hands may never enter the processing zone when the ma-

chine is in operation.

• Release the handle button and switch oﬀ the machine prior

to any operations.

Warning!

This electric tool generates an electromagnetic ﬁeld during op-

eration. This ﬁeld can impair active or passive medical implants

under certain conditions. In order to prevent the risk of serious

or deadly injuries, we recommend that persons with medical

implants consult with their physician and the manufacturer of

the medical implant prior to operating the electric tool.

7. Technical data

AC motor.....................................................220 - 240 V

50Hz

Power S1 .....................................................................1700 Watt

Operating mode ............................................ S6 25%* 2000W

Idle speed n

..............................................................4800 min

-1

Carbide saw blade ...............................ø 210 x ø 30 x 2,6 mm

Number of teeth .......................................................................24

Maximum tooth width of saw blade ..................................3 mm

Swivel range .................................................. -45° / 0°/ +45°

Mitre cut .......................................................0° to 45° to the left

Saw width at 90° ................................................. 340 x 65 mm

Saw width at 45° ................................................. 240 x 65 mm

Saw width at 2 x 45°

(double mitre cut)) ................................................. 240 x 38 mm

Protection class ...................................................................II /

Weight .....................................................................ca. 12,15 kg

Laser class ................................................................................... 2

Wavelength of laser ........................................................ 650 nm

Laser output .....................................................................< 1 mW

* S6, continuous operation periodic duty. Identical duty cycles

with a period at load followed by a period at no load. Running

time 10 minutes; duty cycle is 25% of the running time.

The work piece must have a minimum height of 3

mm and a minimum width of 10 mm.

Make sure that the workpiece is always secured

with the clamping device.

Noise

Total noise values determined in accordance with EN 62841.

Sound pressure level L

....................... 96,5 dB(A)

Uncertainty K

...............................................3 dB

Sound power level L

........................ 109,5 dB(A)

Uncertainty K

..............................................3 dB

Wear hearing protection.

The eﬀects of noise can cause a loss of hearing

The above-mentioned noise emission values were measured in

accordance with a standardised test procedure and can be

used to compare one power tool with another.

The above-mentioned noise emission values can also be used

for the preliminary assessment of exposure.

Warning:

• The noise emissions during the actual use of the power tool

may diﬀer from the above-mentioned values depending on

the power tool being used, in particular on the type of work-

piece being processed.

8 GB

• Try to keep emissions as low as possible, for example by

limiting your working time. In this regard, all the operational

cycle phases must be taken into consideration (such as the

times when the tool is switched oﬀ or running idle).

8. Before starting the equipment

• Open the packaging and remove the device carefully.

• Remove the packaging material as well as the packaging

and transport bracing (if available).

• Check that the delivery is complete.

• Check the device and accessory parts for transport damage.

• If possible, store the packaging until the warranty period has

expired.

ATTENTION

The device and packaging materials are not toys!

Children must not be allowed to play with plastic

bags, ﬁlm and small parts! There is a risk of swal-

lowing and suﬀocation!

• The equipment must be set up where it can stand securely.

Secure the machine on a workbench or a base frame with 4

screws (not included in delivery) using the holes on the ﬁxed

saw table (15).

• Pull out the pre-installed tilt protection (36) completely and

secure it with an Allen key (D).

• Adjust the adjusting screw (38) to the level of the tabletop to

avoid wobbling of the machine.

• All covers and safety devices have to be properly ﬁtted be-

fore the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed before,

watch out for foreign bodies such as nails or screws, etc.

• Before you press the ON/OFF switch check that the saw

blade is ﬁtted correctly. Moving parts must run smoothly.

• Before you connect the equipment to the power supply make

sure the data on the rating plate are dentical to the mains

data.

8.1 Checking the moving saw blade guard safety

device (5)

The saw blade guard protects against accidental contact with

the saw blade and from chips ﬂying around.

Check function

To do so, fold the saw downwards:

• The saw blade guard must provide free access to the saw

blade without touching other parts.

• When folding the saw upwards into the starting position, the

saw blade guard must cover the saw blade automatically.

9. Attachment

9.1 Attaching the crosscut, drag and mitre saw

(ﬁg.1/2/4/5)

• In order to adjust the rotary table (14), loosen the handle

(11) approximately 2 turns and pull up the latched position

lever (35) with your index ﬁnger.

• Turn the rotary table (14) and pointer (12) to the desired

angle measurement on the scale (13) and use the handle

(11) to secure it.

• By slightly pushing down the machine head (4) while pull-

ing out and removing the locking bolt (23) from the motor

mount, the locking bolt (23) will be secured in the top posi-

tion and the saw will be unlocked from the bottom position.

• Turn the locking bolt (23) 90 degrees to secure it in the un-

locked position.

• Swing the machine head (4) up.

• It is possible to secure the clamping devices (7) to the left or

right on the ﬁxed saw table (15). Insert the clamping devices

(7) in the holes on the rear side of the stop rail (16) and se-

cure it with the star grip screws (7a). For 0°- 45° mitre cuts,

the clamping device (7) must only be mounted on the right

side (see ﬁg. 11-12).

• It is possible to tilt the machine head (4) a max. 45° to the

left by loosening the set screw (22).

• Workpiece supports (8) must always be secured and used

during work. Set the desired table size by loosening the set

screw (9). Then tighten the set screw (9) again.

9.2 Sawdust bag (ﬁg. 1/22)

The saw is equipped with a debris bag (17) for sawdust and

chips.

Squeeze together the metal ring on the dust bag and attach it

to the outlet opening in the motor area.

The debris bag (17) can be emptied by means of a zipper at

the bottom.

9.2.1 Connection to an external dust extractor

• Connect the vacuum hose with the dust extraction spout.

• The industrial vacuum cleaner must be suitable for the mate-

rial being worked.

• When vacuuming dust that is especially detrimental to health

or carcinogenic, use a special vacuum cleaner.

9.3 Precision adjustment of the stop for crosscut

90° (ﬁg. 1/2/5/6)

Tools required:

- Allen key 6 mm

- Open-ended spanner SW13 (not included in the scope of

delivery)

• No stop angle included.

• Lower the machine head (4) and secure it using the locking

bolt (23).

• Loosen the set screw (22).

• Position the angle stop (A) between the saw blade (6) and

the rotary table (14).

• Loosen the lock nut (26a).

• Adjust the adjusting screw (26) until the angle between the

saw blade (6) and rotary table (14) is 90°.

• Tighten the lock nut (26a) again.

• Subsequently check the position of the angle indicator. If

necessary loosen the pointer (19) using a Philips screwdriv-

er, set to position 0° on the angle scale (18) and re-tighten

the retaining screw.

9GB

9.4 Precision adjustment of the stop for mitre cut

45° (ﬁg. 1/2/5/9/10)

Tools required:

- Allen key 6 mm

- Open-ended spanner SW13 (not included in the scope of

delivery)

• No stop angle included.

• Lower the machine head (4) and secure it using the locking

bolt (23).

• Fix the rotary table (14) in the 0° position.

Attention!

For bevel cuts (inclined saw head), the moveable stop rail

(16a) must be ﬁxed in the outer position. (Left side).

• Open the set screw (16b) for the moveable stop rail (16a)

and push the moveable stop rail (16a) outwards.

• The moveable stop rail (16a) must be ﬁxed far enough in

front of the innermost position that the distance between the

stop rail (16a) and the saw blade (6) amounts to a maxi-

mum of 8 mm.

• The moveable stop rail (28) must be ﬁxed in the inner posi-

tion. (Right side).

• Before making a cut, check that the stop rail (16a) and the

saw blade (6) cannot collide.

• Loosen the set screw (22) and use the handle (1) to angle

the machine head (4) 45° to the left.

• 45° - position angle stop (B) between the saw blade (6) and

rotary table (14).

• Loosen the lock nut (27a) and adjust the screw (27) until the

angle between the saw blade (6) and the rotary table (14)

is precisely 45°.

• Tighten the lock nut (27a) again.

• Subsequently check the position of the angle indicator. If

necessary, loosen the pointer (19) using a Philips screwdriv-

er, set to position 45° on the angle scale (18) and re-tighten

the retaining screw.

10. Operation

10.1 Using the laser (ﬁg. 18)

• To switch on: Press the ON/OFF switch laser (33) 1x. A

laser line is projected onto the material you wish to process,

providing an exact guide for the cut.

• To switch oﬀ: Press again the ON/OFF switch laser (33).

10.2 Limiting the cutting depth (ﬁg. 3/13)

• The cutting depth can be inﬁnitely adjusted using the screw

(24). To do this loosen the knurled nut (24a) on the screw

(24). Turn the screw (24) in or out to set the required cutting

depth. Then re-tighten the knurled nut (24a) on the screw

(24).

• Check the setting by completing a test cut.

10.3 Serial cutting

For repeated cuts of the same length, the length stop (37) can

be opened. You can use the length stop (37) on the right and

on the left.

• Fold up the length stop (37).

• Loosen the set screw for workpiece support (9).

• Pull out the workpiece support (8).

• Set the required dimension between saw blade and length

stop (37).

• Re-tighten the set screw for workpiece support (9).

• Perform cutting as described in sections 10.4 to 10.7.

10.4 Crosscut 90° and turntable 0° (ﬁg. 1/2/7)

In the case of cutting widths up to approx. 100 mm it is possible

to ﬁx the traction function of the saw with the set screw (20) in

the rear position. In this position the machine can be operated

in cross cutting mode. If the cutting width is over 100 mm then

it is necessary to ensure that the set screw (20) is loose and the

machine head (4) can move.

Attention!

For 90° crosscuts, the moveable stop rail (16a) must be ﬁxed

in the inner position.

• Open the set screw (16b) for the moveable stop rail (16a)

and push the moveable stop rail (16a) inwards.

• The moveable stop rail (16a) must be locked in a position far

enough from the inner position that the distance between the

stop rail (16a) and the saw blade (6) is no more than 8 mm..

• Before making the cut, check that the stop rail (16a) and the

saw blade (6) cannot collide.

• Re-tighten the set screw (16b).

• Move the machine head (4) to its upper position.

• Use the handle (1) to push back the machine head (4) and

ﬁx it in this position if required (dependent on the cutting

width).

• Place the piece of wood to be cut at the stop rail (16) and

on the turntable (14).

• Lock the material with the clamping devices (7) on the ﬁxed

saw table (15) to prevent the material from moving during

the cutting operation.

• Release the lock switch (3) and press the ON/OFF switch

(2) to start the motor.

• With the drag guide (21) ﬁxed in place (21):: use

the handle (1) to move the machine head (4) steadily and

with light pressure downwards until the saw blade (6) has

completely cut through the work piece.

• With the drag guide (21) not ﬁxed in place (21):

pull the machine head (4) all the way to the front. Lower the

handle (1) to the very bottom by applying steady and light

downward pressure. Now push the machine head (4) slowly

and steadily to the very back until the saw blade (6) has

completely cut through the work piece.

• When the cutting operation is completed, move the machine

head back to its upper (home) position and release the ON/

OFF button (2).

Attention! The machine executes an upward stroke auto-

matically due to the return spring, i.e. do not release the han-

dle (1) after completing the cut; instead allow the machine

head to move upwards slowly whilst applying light counter

pressure.

10.5 Crosscut 90° and turntable 0° - 45°

(ﬁg. 1/7/8)

The crosscut, drag and mitre saw can be used to make cross-

cuts of 0° -45° to the left and 0° -45° to the right in relation

to the stop rail.

10 GB

Important!

For 90° crosscuts, the moveable stop rail (16a) must be ﬁxed

in the inner position.

• Open the set screw (16b) for the moveable stop rail (16a)

and push the moveable stop rail (16a) inwards.

• The moveable stop rail (16a) must be ﬁxed far enough in

front of the innermost position that the distance between the

stop rail (16a) and the saw blade (6) amounts to a minimum

of 8 mm.

• Before making the cut, check that the stop rail (16a) and the

saw blade (6) cannot collide.

• Secure the set screw (16b) again.

• Loosen the handle (11) if tightened, pull up the latched posi-

tion lever (35) with your index ﬁnger and use the handle

(11) to set the rotary table (14) to the desired angle.

• The pointer (12) on the rotary table must match the desired

angle on the scale (13) on the ﬁxed saw table (15).

• Re-tighten the handle (11) to secure the rotary table (14).

• Cut as described under section 10.5.

10.6 Mitre cut 0°- 45° and turntable 0°

(ﬁg. 1/2/11)

The crosscut, drag and mitre saw can be used to make mitre

cuts of 0° - 45° in relation to the work face.

Attention!

For bevel cuts (inclined saw head), the moveable stop rail

(16a) must be ﬁxed in the outer position. (Left side).

• Open the set screw (16b) for the moveable stop rail (16a)

and push the moveable stop rail (16a) outwards.

• The moveable stop rail (16a) must be ﬁxed far enough in

front of the innermost position that the distance between the

stop rail (16a) and the saw blade (6) amounts to a minimum

of 8 mm.

• The moveable stop rail (28) must be ﬁxed in the inner posi-

tion. (Right side).

• Before making a cut, check that the stop rail (16a) and the

saw blade (6) cannot collide.

• Secure the set screw (16b) again.

• Move the machine head (4) to the top position.

• Fix the rotary table (14) in the 0° position.

• Loosen the set screw (22) and use the handle (1) to angle

the machine head (4) to the left, until the pointer (19) indi-

cates the desired angle measurement on the scale (18).

• Re-tighten the set screw (22).

• Cut as described in section 10.4.

10.7 Mitre cut 0°- 45° and turntable 0°- 45°

(ﬁg. 2/4/12)

The crosscut, drag and mitre saw can be used to make mitre

cuts to the left of 0°- 45° in relation to the work face and, at

the same time, 0° - 45° to the left or 0° - 45° to the right in

relation to the stop rail (double mitre cut).

Attention!

For bevel cuts (inclined saw head), the moveable stop rail

(16a) must be ﬁxed in the outer position. (Left side).

• Open the set screw (16b) for the moveable stop rail (16a)

and push the moveable stop rail (16a) outwards.

• The moveable stop rail (16a) must be ﬁxed far enough in

front of the innermost position that the distance between the

stop rail (16a) and the saw blade (6) amounts to a minimum

of 8 mm.

• Before making a cut, check that the stop rail (16a) and the

saw blade (6) cannot collide.

• Re-tighten the set screw (16b).

• Move the machine head (4) to its upper position.

• Release the rotary table (14) by loosening the handle (11).

• Using the handle (11), set the rotary table (14) to the de-

sired angle (refer also to point 10.5 in this regard).

• Re-tighten the handle (11) to secure the rotary table (14).

• Undo the set screw (22).

• Use the handle (1) to tilt the machine head (4) to the left until

it coincides with the required angle value (in this connection

see also section 10.6).

• Re-tighten the set screw (22).

• Cut as described under section 10.4.

11. Maintenance

m Warning! Prior to any adjustment, maintenance

or service work disconnect the mains power plug!

11.1 General maintenance measures

Wipe chips and dust oﬀ the machine from time to time using a

cloth. In order to extend the service life of the tool, oil the rotary

parts once monthly. Do not oil the motor.

When cleaning the plastic do not use corrosive products.

11.2 Cleaning the moving saw blade guard safety

device (5)

Always check the saw blade guard for debris before using the

machine.

Remove old sawdust and splinters using a brush or similar tool.

11.3 Replacing the table insert

Danger!

With a damaged table insert (10) there is a risk of small parts

getting stuck between table insert and saw blade, blocking the

saw blade. Immediately replace damaged table in-

serts!

1. Remove screws at table insert. If required, turn rotary table

and incline saw head to be able to reach the screws.

2. Remove table insert.

3. Install new table insert.

4. Tighten the screws at table insert.

11.4 Brush inspection

Check the carbon brushes after the ﬁrst 50 operating hours

with a new machine, or when new brushes have been ﬁtted.

After carrying out the ﬁrst check, repeat the check every 10

operating hours.

If the carbon is worn to a length of 6 mm, or if the spring or

contact wire are burned or damaged, it is necessary to replace

both brushes. If the brushes are found to be usable following

removal, it is possible to reinstall them.

When servicing the carbon brushes, open the two latches coun-

terclockwise (as shown in Figure 21). Then remove the carbon

brushes.

Replace the carbon brushes in the reverse order.

11GB

11.5 Changing the saw blade (ﬁg. 1/2/14-17)

Remove the power plug!

Important!

Wear safety gloves when changing the saw blade.

Risk of injury!

• Swing the machine head (4) upwards and lock with the lock-

ing bolt (23).

• Loosen the retaining screw (5a) of the cover using a Philips

screwdriver.

WARNING!

Do not fully remove this screw.

• Fold the saw blade guard (5) upwards until the saw blade

guard (5) is above the ﬂange screw (28).

• With one hand insert the Allen key (C) in the ﬂange screw

(28).

• Hold the Allen key (C) and slowly close the saw blade guard

(5) until it touches the Allen key (C).

• Firmly press the saw shaft lock (30) and slowly rotate the

ﬂange screw (28) in clockwise direction. The saw shaft lock

(30) engages after no more than one rotation.

• Now, using a little more force, slacken the ﬂange screw (28)

in the clockwise direction.

• Turn the ﬂange screw (28) right out and remove the outer

ﬂange (29).

• Take the blade (6) oﬀ the inner ﬂange (31) and pull out

downwards.

• Carefully clean the ﬂange screw (28), outer ﬂange (29) and

inner ﬂange (31).

• Fit and fasten the new saw blade (6) in reverse order.

• Fold the saw blade guard (5) downwards until the saw

blade guard (5) engages in the locking screw (5a).

• Re-tighten the locking screw (5a).

• Important!

The cutting angle of the teeth, in other words the direction of

rotation of the saw blade (6) must coincide with the direction

of the arrow on the housing.

• Before continuing your work make sure that all safety de-

vices are in good working condition.

• Important!

Every time that you change the saw blade (6), check to see

that it spins freely in the table insert (10) in both perpendicu-

lar and 45° angle settings.

• Important!

The work to change and align the saw blade (6) must be

carried out correctly.

11.6 Adjusting the laser (ﬁg. 19-20)

If the laser (32) ceases to indicate the correct cutting line, you

can readjust the laser. To do so, open the screws (32b) and

remove the front cover (32a). Loosen the Philips head screws

(E) and set the laser by moving sideways until the laser beam

strikes the teeth of the saw blade (6).

After adjusting and tightening the laser, mount the front cover

by tightening both screws (32b) by hand.

11.7 Service information

Please note that the following parts of this product are sub-

ject to normal or natural wear and that the following parts are

therefore also required for use as consumables.

Wear parts*: carbon brushes, saw blade, table inserts, saw-

dust bags

* Not necessarily included in the scope of delivery!

12. Transport

• Tighten the handle (11) to lock the rotary table.

• Press the machine head (4) downwards and secure with the

locking bolt (23).

• Fix the saw’s drag function with the locking screw for drag

guide (20) in rear position.

• Carry the equipment by the ﬁxed saw table (15).

• When reassembling the equipment proceed as described

under section 8 and 9.

13. Storage

Store the device and its accessories in a dark, dry and frost-

proof place that is inaccessible to children. The optimum stor-

age temperature is between 5 and 30˚C.

Store the electrical tool in its original packaging.

Cover the electrical tool in order to protect it from dust and

moisture.

Store the operating manual with the electrical tool.

14. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies with

the applicable VDE and DIN provisions. The cus-

tomer‘s mains connection as well as the extension

cable used must also comply with these regula-

tions.

• The product meets the requirements of EN 61000-3-11 and

is subject to special connection conditions. This means that

use of the product at any freely selectable connection point

is not allowed.

• Given unfavourable conditions in the power supply the prod-

uct can cause the voltage to ﬂuctuate temporarily.

• The product is intended solely for use at connection points

that

a) do not exceed a maximum permitted supply impedance

“Z” (Zmax = 0.339 Ω), or

b) have a continuous current-carrying capacity of the mains

of at least 100 A per phase.

• As the user, you are required to ensure, in consultation with

your electric power company if necessary, that the connec-

tion point at which you wish to operate the product meets

one of the two requirements, a) or b), named above.

Important information

In the event of an overloading the motor will switch itself oﬀ. Af-

ter a cool-down period (time varies) the motor can be switched

back on again.

12 GB

Damaged electrical connection cable

The insulation on electrical connection cables is often dam-

aged.

This may have the following causes:

• Passage points, where connection cables are passed through

windows or doors.

• Kinks where the connection cable has been improperly fas-

tened or routed.

• Places where the connection cables have been cut due to

being driven over.

• Insulation damage due to being ripped out of the wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not be used

and are life-threatening due to the insulation damage.

Check the electrical connection cables for damage regularly.

Make sure that the connection cable does not hang on the

power network during the inspection.

Electrical connection cables must comply with the applicable

VDE and DIN provisions. Only use connection cables of the

same designation.

The printing of the type designation on the connection cable

is mandatory.

If the power cord of this device is damaged, it must be replaced

by a special power cord, which is available from the manufac-

turer or its service department.

AC motor:

The mains voltage must be 220 - 240 V

• Extension cables up to 25 m long must have a cross-section

of 1.5 mm

Connections and repairs of electrical equipment may only be

carried out by an electrician.

Please provide the following information in the event of any

enquiries:

• Type of current for the motor

• Machine data - type plate

15. Disposal and recycling

The equipment is supplied in packaging to prevent it from being

damaged in transit. The raw materials in this packaging can be

reused or recycled.

The equipment and its accessories are made of various types

of material, such as metal and plastic. Defective components

must be disposed of as special waste. Ask your dealer or your

local council.

The packaging is wholly composed of environment-

ally-friendly materials that can be disposed of at a

local recycling centre.

Contact your local refuse disposal authority for

more details of how to dispose of your worn-out

electrical devices.

Old devices must not be disposed of with house-

hold waste!

This symbol indicates that this product must not be dis-

posed of together with domestic waste in compliance

with the Directive (2012/19/EU) pertaining to waste

electrical and electronic equipment (WEEE). This prod-

uct must be disposed of at a designated collection point. This

can occur, for example, by handing it in at an authorised col-

lecting point for the recycling of waste electrical and electronic

equipment. Improper handling of waste equipment may have

negative consequences for the environment and human health

due to potentially hazardous substances that are often con-

tained in electrical and electronic equipment. By properly dis-

posing of this product, you are also contributing to the eﬀective

use of natural resources. You can obtain information on collec-

tion points for waste equipment from your municipal administra-

tion, public waste disposal authority, an authorised body for

the disposal of waste electrical and electronic equipment or

your waste disposal company.

13GB

16. Troubleshooting

Fault Possible cause Remedy

Motor does not work Motor, cable or plug defective, fuses burnt Arrange for inspection of the machine by a specialist.

Never repair the motor yourself. Danger!

Check fuses and replace as necessary

The motor starts up slowly

and does not reach oper-

ating speed.

Voltage too low, coils damaged, capacitor burnt Contact an electrician to check the voltage.

Arrange for inspection of the motor by a specialist. Ar-

range for replacement of the capacitor by a specialist

Motor makes excessive

noise

Coils damaged, motor defective Arrange for inspection of the motor by a specialist

The motor does not reach

its full power.

Circuits in the network are overloaded (lamps,

other motors, etc.)

Do not use any other equipment or motors on the same

circuit

Motor overheats easily. Overloading of the motor, insuﬃcient cooling of

the motor

Avoid overloading the motor while cutting, remove dust

from the motor in order to ensure optimal cooling of the

motor

Saw cut is rough or wavy Saw blade dull, tooth shape not appropriate for

the material thickness

Re-sharpen saw blade and/or use suitable saw blade

Workpiece pulls away

and/or splinters

Excessive cutting pressure and/or saw blade not

suitable for use

Insert suitable saw blade

14 GB

17. Warranty certiﬁcate

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device

develops a fault, please contact our service department at the address shown on this guarantee card. Of course, if you would prefer to

call us then we are also happy to oﬀer our assistance under the service number printed below. Please note the following terms under which

guarantee claims can be made:

• These guarantee terms cover additional guarantee rights and do not aﬀect your statutory warranty rights. We do not charge you for

this guarantee.

• Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the rectiﬁcation of these de-

fects or replacement of the device. Please note that our devices have not been designed for use in commercial, trade or industrial ap-

plications. Consequently, the guarantee is invalidated if the equipment is used in commercial, trade or industrial applications or for

other equivalent activities. The following are also excluded from our guarantee: compensation for transport damage, damage caused

by failure to comply with the installation/assembly instructions or damage caused by unprofessional installation, failure to comply with

the operating instructions (e.g. connection to the wrong mains voltage or current type), misuse or inappropriate use (such as overload-

ing of the device or use of non-approved tools or accessories), failure to comply with the maintenance and safety regulations, ingress

of foreign bodies into the device (e.g. sand, stones or dust), eﬀects of force or external inﬂuences (e.g. damage caused by the device

being dropped) and normal wear resulting from proper operation of the device.

The guarantee is rendered null and void if any attempt is made to tamper with the device.

• The guarantee is valid for a period of 3 years starting from the purchase date of the device. Guarantee claims should be submitted

before the end of the guarantee period within two weeks of the defect being noticed. No guarantee claims will be accepted after the

end of the guarantee period. The original guarantee period remains applicable to the device even if repairs are carried out or parts

are replaced. In such cases, the work performed or parts ﬁtted will not result in an extension of the guarantee period, and no new

guarantee will become active for the work performed or parts ﬁtted. This also applies when an on-site service is used.

• In order to assert your guarantee claim, please contact the service partner shown below. If the complaint is within the guarantee pe-

riod, we will provide you with a return slip, with which you can return your defective device free of charge to us. It would help us if you

could describe the nature of the problem in as much detail as possible. If the defect is covered by our guarantee then your device will

either be repaired immediately and returned to you, or we will send you a new device.

Of course, we are also happy oﬀer a chargeable repair service for any defects which are not covered by the scope of this guarantee or for

units which are no longer covered. To take advantage of this service, please send the device to our service address.

Service-Hotline (GB):

+800 4003 4003

(0,00 EUR/Min.)

Service-Email (GB):

service.[email protected]

Service Address (GB):

Forest Park & Garden

Coed Court, Taﬀsmead Road

Treforest, Ind. Estate, Pontypridd CF375SW

At www.lidl-service.com you can download this and many more manuals, product videos plus installation

software.

The QR code takes you directly to the Lidl service page (www.lidl-service.com) and you can open your oper-

ating manual by entering the article number (IAN) 331932_1907.

15PL

Spis treści: Strona:

1. Wyjaśnienie symboli na urządzeniu ................................................................................................................................................................16

2. Wprowadzenie .................................................................................................................................................................................................17

3. Opis urządzenia (rys. 1-22) .............................................................................................................................................................................17

4. Zakres dostawy .................................................................................................................................................................................................18

5. Użycie zgodne z przeznaczeniem ..................................................................................................................................................................18

6. Bezpieczeństwa ................................................................................................................................................................................................18

7. Dane techniczne................................................................................................................................................................................................22

8. Przed uruchomieniem ........................................................................................................................................................................................23

9. Montaż ..............................................................................................................................................................................................................23

10. Obsługa .............................................................................................................................................................................................................24

11. Konserwacja ......................................................................................................................................................................................................25

13. Przechowywanie ...............................................................................................................................................................................................26

14. Przyłącze elektryczne .......................................................................................................................................................................................26

15. Utylizacja i recykling .........................................................................................................................................................................................27

16. Pomoc dotycząca usterek .................................................................................................................................................................................28

17. Gwarancja ........................................................................................................................................................................................................29

18. Deklaracja zgodności .......................................................................................................................................................................................59

Strona jest ładowana ...