AAT NVIP-2SD-6100/20/F Instrukcja obsługi

Quick start guide

NVIP-2SD-6100/20/F

NVIP-2SD-6100/20/F Quick start guide version 1.1

2

INFORMATIONS

THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING

DIRECTIVES:

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed

for self installation in households by individuals without technical knowledge.

The manufacturer is not responsible for defects and damages resulted from improper or inconsistent

with user’s manual installation of the device in the system.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN

PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE

PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE

PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF EXCLUDING

THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO

USER-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE

PERSONNEL MAY OPEN THE UNIT.

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS.

DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 26 February 2014 on the harmonization of the laws of the Member States

relating to electromagnetic compatibility (OJ L 96, 29.3.2014, p. 79 - 106, with changes)

DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 4 July 2012 on waste electrical and electronic equipment (WEEE) (OJ L 97,

24.7.2012, p. 38 - 71,with changes)

DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 8 June

2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (OJ L

174, 1.7.2011, p. 88 - 110, with changes)

NVIP-2SD-6100/20/F Quick start guide version 1.1

3

IMPORTANT SAFEGUARDS AND WARNINGS

1. Prior to undertaking any action with the device, please consult following manual, and read all the safety and

operating instructions before operating the device.

2. Please keep the following manual for the time of device’s lifespan in case when referring to the contents of

the manual would become necessary.

3. Follow all the safety precautions described in this manual. Improper installation and camera operation may

have impact on operator safety as well as camera operational reliability and lifespan.

4. Camera mounting and operations should be conducted according to this manual, both for users and service

personnel.

5. Please unplug the unit from the power before starting maintenance procedures.

6. Please use only attachments / accessories specified by the manufacturer.

7. Operating the camera in high-humidity environments (such as in proximity of swimming pools, bathtubs,

inside wet cellars etc.) when the mounting method doesn't provide declared water tightness is forbidden.

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not

recommended since it may lead to heat build-up and damaging the device itself in consequence.

9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly

mounted camera may be the cause of fatal accident or be seriously damaged itself. Camera must be mounted

by qualified personnel with proper authorization, in accordance to user’s manual.

10.Device should be supplied only from power sources which parameters are in accordance to one’s pointed out

by the producer in camera technical datasheet. Therefore it is forbidden to supply the camera from power

sources with their parameters unknown, unstable or not meeting the producer’s requirements.

11.Signal cables (conducting TV or/and telemetric signal) should be placed in a way excluding the possibility of

damaging them by accident. Special attention must be paid to cables going out of the camera and connecting

power supply;

12.To avoid equipment damage, whole TV circuit should be equipped with properly made (in accordance with

Polish Regulations) discharge, overload and lightning protection devices. Usage of separating transformers is

advised.

13.Electric installation supplying the device should be designed to meet the specifications given by the producer

in such a way, that overloading it is impossible.

14. Camera should be protected from foreign objects entering its inside, liquids and excessive humidity.

15. User cannot repair or upgrade equipment himself. All maintenance actions and repairs should be done only

by the qualified service personnel.

16. Unplug the camera from the power source immediately and contact the proper maintenance department

when the following occurs:

• Damages to the power cord or to the plug itself;

• Liquids getting inside the device or exposure to strong mechanical shock;

• Device behaves in a way not described in the manual and all adjustments approved by the

manufacturer, and possible to apply by user himself, seem not to have any effect;

• Camera is damaged;

• Atypical behaviour of the camera components may be seen (heard).

17. In case of repairs please pay attention to using only original replacement parts (with their parameters in

accordance to those specified by the producer) should be paid. Non-licensed service and non-genuine

replacement parts may cause fire or electrocution;

18. After maintenance procedures please conduct device tests and make sure that all the camera components are

operating correctly.

Due to the product being constantly enhanced and optimized, certain parameters and functions described in the

manual in question may change without further notice.

We strongly suggest visiting the www.novuscctv.com website in order to access the newest manual

NVIP-2SD-6100/20/F Quick start guide version 1.1

4

FOREWORD INFORMATION

1. FOREWORD INFORMATION

1.1. General characteristic

• Mechanical IR cut filter

• IR operation capability - built-in IR LED illuminator

• Imager resolution: 2 megapixels

• Min. Illumination: from 0.003 lx with IR off

• Motor-zoom lens, AI and AF function

• Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions

• 8 tours (max. 16 presets each)

• 2 auto-scan functions

• 4 patterns (max. 180 sec. per pattern)

• 360 preset commands

• Optical zoom: up to 20x

• Privacy zones

• Motion detection

• Advanced image analysis functions (VCA)

• “Auto-Flip” function allows the tilt to rotate 180° and reposition itself for continuous viewing of a

moving object directly beneath the dome

• Compression: H.264, H.265, M-JPEG

• Video processing resolution: up to 1920 x 1080

• RTP/RTSP protocol support for video & audio transmission

• Triple stream mode: compression, resolution, speed and quality defined individually for each video

stream

• Network connection control function

• Built-in web server: camera configuration through the website

• Diverse definition of system reactions to alarm events: e-mail with attachment, saving file on FTP

server, HTTP notification, save on SD card

• PTZ control directly from the website and NMS (NOVUS MANAGEMENT SYSTEM)

• Schedule recording function

• Network protocols support: ONVIF Profile S, HTTP, HTTPS, TCP/IP, IPv4/v6, UDP/IP, FTP,

DHCP, DDNS, NTP, RTSP, SMTP, PPPoE

• Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,

playback and remote IP devices administration

• IP 66

• Housing and wall mount bracket in-set included

• Power supply: 12 VDC, PoE (IEEE 802.3at)

NVIP-2SD-6100/20/F Quick start guide version 1.1

5

1.2 Technical specification

FOREWORD INFORMATION

IMAGE

Image Sensor 2 MPX CMOS sensor 1/2.8” SONY STARVIS

Number of Eecve Pixels 1945 (H) x 1097 (V)

Min. Illuminaon

0.006 lx/F1.6 - color mode,

0.003 lx/F1.6 - B/W mode,

0 lx (IR on) - B/W mode

S/N Rao > 50 dB (AGC o)

Electronic Shuer auto/manual: 1/1 s ~ 1/25000 s

Digital Slow Shuer (DSS) up to 1 s

Wide Dynamic Range (WDR) yes (double scan sensor), 120dB

Digital Noise Reducon (DNR) 2D, 3D

Defog Funcon (F-DNR) yes

Highlight Compensaon (HLC) yes

Back Light Compensaon (BLC) yes

LENS

Opcal Zoom 20x

Lens Type motor-zoom, auto-iris funcon, f=5.5 ~ 110 mm/F1.6 ~ F3.5

Auto-focus zoom trigger

DAY/NIGHT

Switching Type mechanical IR cut lter

Switching Mode auto, manual, me

Switching Schedule yes

Visible Light Sensor yes

NETWORK

Stream Resoluon 1920 x 1080 (Full HD), 1280 x 720 (HD), 640 x 480 (VGA), 480 x 240,

Frame Rate 30 fps for 1920 x 1080 (Full HD) and lower resoluons

Mulstreaming Mode 3 streams

Video/Audio Compression H.264, H.265, MJPEG/-

Number of Simultaneous Connecons max. 6

Bandwidth 36 Mb/s in total

Network Protocols Support

HTTP, TCP/IP, IPv4/v6, UDP, HTTPS, FTP, DHCP, DDNS, NTP, RTSP, UPnP,

SNMP, QoS, IEEE 802.1X, PPPoE, SMTP

ONVIF Protocol Support Prole S

Camera Conguraon

from Internet Explorer browser,

languages: Polish, English, and others

Compable Soware NMS, NVR-6000 Viewer

Mobile applicaons SuperLive Plus (iPhone, Android)

PTZ

Preset Commands 360 including 20 special (funcon) presets

Tours 8 (up to 16 presets per tour)

Auto-Scans 2

Paerns 4 (max. 180 s for each paern)

Tilt/Pan Range -5° ~ 90°/360° (connuous)

Pan/Tilt Speed up to 80°/s (proporonal to zoom)

Preset Speed up to 80°/s

NVIP-2SD-6100/20/F Quick start guide version 1.1

6

FOREWORD INFORMATION

1.3. Camera dimensions

OTHER FUNCTIONS

Privacy Zones 4

Moon Detecon yes

Video Content Analysis (VCA) tamper, abandoned object, object disappearance, line cross,

Image Processing 180˚ image rotaon, sharpening, mirror eect, horizontal ip

System Reacon to Alarm Events e-mail with aachment, saving le on FTP server, saving le on SD card

IR LED

LED Number 6

Range up to 150 m (depends on current opcal zoom value)

Smart IR yes (hardware support)

INTERFACES

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Memory Card Slot microSD - capacity up to 128GB

INSTALLATION PARAMETERS

Dimensions (mm) 173 (Ф) x 268 (H) with bracket: 173 (W) x 342 (H) x 300 (L)

Weight 2.1 kg, with bracket: 2.8kg

Degree of Protecon IP 66 (details in the user’s manual)

Enclosure

aluminium, white, IK10 impact rang, in set: outdoor housing

(integrated with the camera), wall mount bracket

Power Supply PoE (IEEE 802.3at)

Surge protecon TVS 4000 V

Power Consumpon

6 W,

15.5 W (IR on),

20 W (IR and heater on)

Operang Temperature -30°C ~ 55°C

Humidity max. 90%, relave (non-condensing)

Built-in Heater/Fan yes/yes

NVIP-2SD-6100/20/F Quick start guide version 1.1

7

START-UP AND INITIAL IP CAMERA CONFIGURATION

1.4. Package contents

After open the package make sure that the following elements are inside:

If any of this elements has been damaged or missing during transport, pack all the elements back into

the original box and contact your supplier for further assistance.

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches

the temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

2. START-UP AND INITIAL IP CAMERA CONFIGURATION

2.1. Description of connectors

1. RJ-45 connector

2. Power connector 12VDC

Novus IP PTZ camera 1 pcs

Wall bracket 1 pcs

User’s manual (short form) 1 pcs

Accessories bag 1pcs

NVIP-2SD-6100/20/F Quick start guide version 1.1

8

START-UP AND INITIAL IP CAMERA CONFIGURATION

2.2. Ethernet cable connecting

To maintain tightness of ethernet cable connection, please follow instruction below:

1. Unscrew the nut (1) from the connector cover (2).

2. Route the network cable (without the RJ-45 plug) through the components (1) and (2), than crimp the RJ-45

connector.

3. Plug the RJ-45 connector into the hermetic socket (3), screw the connector cover (2), and than the nut (1).

CAUTION!

The declared degree of protection of the camera relates to its housing and does not take into account the

possibility of moisture infiltration into the camera by connection cables. Connection cables protection

through i.e. sealing up is the camera installer duty. The manufacturer is not liable for any camera

damages caused as a result of failing in performing that activity by installer, which also means that

camera damaged in that way is not subject to warranty repairs.

CAUTION!

Camera power supply connector is not hermetic. Installer should seal this connector by himself.

Camera can be supplied using external power supply unit corresponding with the camera parameters or by using

RJ45 network socket and PoE (IEEE 802.3at) power supply unit. If you’re using external power supply please

connect wires according to polarisation shown on picture

WARNING

It is forbidden to power the camera from the recorder's PoE interfaces, it may damage them.

CAUTION!

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

12 VDC +

GND

Schema of 12VDC power supply connector

1

2

3

1

2

NVIP-2SD-6100/20/F Quick start guide version 1.1

9

START-UP AND INITIAL CAMERA CONFIGURATION

2.3. Mounting the camera

In order to obtain declared degree of protection please seal the mounting place additionally with

appropriate sealing mass, paying special attention to mounting holes.

The declared degree of protection of the camera relates to its housing and does not take into account the

possibility of moisture infiltration into the interior of the camera by connecting cables. Connection

cables protection through i.e. sealing up is the responsibility of the camera installer. The manufacturer

is not liable for any damages to the camera caused as a result of failing in performing that activity by

installer, which also means that camera damaged in that way is not subject to warranty repairs.

CAUTION!

Due to safety reasons, maximum load capacity of surface shouldn’t be less than 20kg.

In order to successfully mount a camera, please follow the procedure below:

• Put the bracket to the wall in a desired mounting place (with cable hole). Taking the bracket’s

base screw holes as a pattern, mark future drilling holes for screws using a punch.

• Drill 4 holes I the mounting surface in accordance with previously done markings, insert the

expansion plugs into the holes.

• Secure the camera with a safety wire.

• Thread the wires of camera through the hole in the wall bracket.

NVIP-2SD-6100/20/F Quick start guide version 1.1

10

• Attach the camera to the bracket.

• Then tighten the three bolts to fix the bracket and camera.

• By using the description of the terminals from the previous chapter and the appropriate

accessories, connect required signal and power supply cables.

CAUTION!

Connection the power cable to the camera must be performed after disconnecting the power

source. Power can be on only after the camera is fully mounted.

• Put the excess cable back into the bracket.

• Screw on the camera with the bracket to the wall.

• After the above steps the camera is ready to work.

START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-2SD-6100/20/F Quick start guide version 1.1

11

2.4. Starting the IP camera

To run NOVUS IP camera you have to connect ethernet cable between camera and network PoE switch

with PoE support (IEEE 802.3at).

You can also power it from 12VDC power supply compatible with camera power supply specification.

After connecting power initialization process takes about 2 minutes. Then you can connect to the

camera via web browser.

The recommended way to start an IP camera and perform its configuration is a direct connection to the

network switch which is not connected to other devices. To obtain further information about network

configuration parameters (IP address, gateway, network mask, etc.) please contact your network

administrator.

• Connection using network switch with PoE support (IEEE 802.3at)

• Connection using external power supply and network switch

START-UP AND INITIAL CAMERA CONFIGURATION

Network Switch

Power supply and

network transmission

Computer

IP Camera

Network PoE Switch

Network transmission

IP Camera

Network transmission

Computer

Network transmission

NVIP-2SD-6100/20/F Quick start guide version 1.1

12

• Connection using external power supply directly to the computer

2.5. Initial configuration via the web browsr

The default network settings for NVIP-2SD-6100/20/F camera are :

1. IP address - 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to set PC IP address appropriately, so the two devices can

operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera is from

range 192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same

addresses for camera and PC computer

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission - cross over cable

Computer

NVIP-2SD-6100/20/F Quick start guide version 1.1

13

2.6. Security recommendations for network architecture and configuration

CAUTION!

Below are shown security recommendations for network architecture and configuration

of CCTV systems that are connected to the Internet to reduce the risk

of unauthorized interference with the system by a third party.

1. Absolutely change the default passwords and user names (if the device gives this possibility) of

all applied network devices (recorders, cameras, routers, network switches, etc.) to the

severely complexity password. Use lowercase and uppercase letters, numbers, and special characters

if there is such possibility.

2. Depending on the available functionality in the order to restrict access to the used network devices

at the administrator account level, it is recommended to configure the users accounts accordingly.

3. Do not use DMZ function (Demilitarized zone) in your router. Using that function you open the

access to recorder system from the Internet on all ports, which gives possibility for an unauthorized

interference with the system.

Instead of DMZ use port forwarding redirect only the ports which are necessary for the performance

of the connection (detailed information about ports of communication in different models

of recorders, cameras, etc. can be found in the operating instructions).

4. Use routers with firewall function and make sure it is enabled and properly configured.

5. It is recommended to change the default network communication port numbers of used devices

if there is such possibility.

6. If used network devices has a UPnP feature and it is not used, turn it off.

7. If used network devices has a P2P feature and it is not used, turn it off.

8. If used network devices support HTTPS protocol for connection, it is recommended to use it.

9. If used network devices support IP filtering for authorized connections function, it is recommended

to use it.

10. If used recorder has two network interfaces it is recommended to use both of them to physically

separate network for cameras and network for Internet connection. The only device in the system,

accessible from Internet will be recorder - there will be no physically access directly to any camera.

START-UP AND INITIAL CAMERA CONFIGURATION

NVIP-2SD-6100/20/F Quick start guide version 1.1

14

3. NETWORK CONNECTION USING WEB BROSWER

3.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming smooth image display

in 1920x1080 resolution and 30 fps speed.

1. CPU Intel i7 3 GHz or faster

2. RAM Memory min. 6 GB

3. VGA card Nvidia GeForce 1GB

4. OS Windows 8 / 8.1 / 10

5. Network card 100/1000 Mb/s

3.2. Connection with IP camera via web browser

CAUTION!

To maintain correct operation as snapshot or video recording you must run the browser as an

administrator.

You have to enter camera IP address in the web browser address bar. If IP address is correct user login

window will be displayed:

In the Language box you can change the display language. Available languages: Polish, English and

others.

CAUTION!

Default user is root and default password is pass. The camera will ask you to change the default

password during the first login (recommended). To do this, check the Modify password option and then

enter and confirm the new password. In order to log into the camera without changing the password,

press the OK button. The message will be displayed each time you log in, until you change your

password, or select the Do not show again option.

NETWORK CONNECTION USING WEB BROWSER

NVIP-2SD-6100/20/F Quick start guide version 1.1

15

If you’re first time running the camera, you will see the screen as below.

To correctly camera working, you need a NetIPCamera plugin. You have to download and install it.

To do it just click Save button, then Run, close IE browser, choose the language, click Install button

and at the end click Finish button. After installation run IE browser.

CAUTION!

In Windows Vista/7/8/8.1/10 the ActiveX applet may be blocked by Windows Defender or User

account control. In such case you should allow to run this applet, or simply disable these functions.

CAUTION!

If the installation fails, changing security settings for the IE browser is required. In order to do that,

please select Enable for Initialize and script ActiveX controls not marked as safe and Download

unsigned ActiveX controls option

NETWORK CONNECTION USING WEB BROWSER

NVIP-2SD-6100/20/F Quick start guide version 1.1

16

4. WWW INTERFACE - WORKING WITH IP CAMERA

4.1. Displaying live pictures

1. .Picture settings

Original Size ..Automatic Size

Fit to screen ..Full screen

2. Camera functions

Live view on/off

Two way audio

Sound on/off

Make a snapshot

WWW INTERFACE - WORKING WITH IP CAMERA

Record a video

3D PTZ control

Digital Zoom

PTZ Menu on/off

3

4

1

2

NVIP-2SD-6100/20/F Quick start guide version 1.1

17

2. Video Parameter

Stream - Stream ID (choose one from available streams)

Bite Rate Type - Information about bit rate type

Bit Rate (kbps) - Information about bit rate

I Frame Interval - Information about I frame interval

Quality - Information about quality

USE TIME STAMP - Video buffer (increases delay when enabled, maximum delay is 5s)

NOTICE: USE TIME STAMP function will not be available when using Flash instead of ActiveX.

3. PTZ Control Panel

PTZ Configure:

Preset - Programming, deleting, and recalling presets

Track - Programming, deleting, and recalling tracks

Speed - Setting speed of movement

3D Position - Turns on/off control using the mouse

North - Setting orientation of the camera

Timer - Setting schedules

PTZ Control:

Arrow keys - Controlling the movement of the camera: up/down, right/left

„Home” key - Function unavailable

Zoom - Zoom control

Focus - Focus control

Iris - Function unavailable

Brush - Function unavailable

On/Off IR - Function unavailable

4. Menu bar

Change Password - Change users password

NOTICE: Default password "pass" can be restored only after restoring default settings of the camera)

Sign Out - Log out from camera

5. Video Control

Camera - Default number of the camera is 1.

Video - Turn on/off video

Audio - Turn on/off audio

Interphone - Turn on/off Interphone

NOTICE: Audio and Interphone functions will not be available when using Flash instead of Activex.

WWW INTERFACE - WORKING WITH IP CAMERA

3. PTZ Menu

PTZ control Panel

PTZ speed slider (1-8)

Scan mode

Wiper (not available)

IR Led switch (On/Off/Auto)

Preset Settings

Cruise Settings

Trace Settings

Delete Preset

Call Preset

Save Preset

4. Alarm Icons:

Motion detection Face detection

4.2. Special (function) presets description

Camera zoom settings

Camera focus settings

Camera Iris settings

Random Scan mode

Group Scan mode

Call Preset

Call NO.90 Preset Run track 1

Call NO.91 - 94 Preset Run cruise 1 - 4

Call NO.95 Preset OSD menu

Call NO.97 Preset Enable random scan

Call NO.99 Preset Enable P-P SCAN

Set NO. 91 Preset

Set random scan

Set Preset

Set NO. 92 Preset Set left border of P-PSCAN

Set NO. 93 Preset Set right border of P-PSCAN

Set NO.94 Preset three times Set the boundary value of the near and middle infrared light

Set NO.95 Preset three times Set the boundary value of the middle and far infrared light

NVIP-2SD-6100/20/F Quick start guide version 1.1

18

5. Instaslling MicroSD card

To install micros sd card in camera:

• Turn power off.

• remove cover form back.

• Put SD card next to the RESET button.

• Reattach the flap that secures the MicroSD card slot.

• Turn power on.

6. RESTORING FACTORY DEFAULTS

NVIP-2SD-6100/20/F cameras allow to restore defaults via:

• Software (web browser level)

• Hardware (using reset button)

6.1. Software restoration of factory settings the IP camera

User can restore default settings. To restore to default settings go to: Maintenance -> Device Restart

tab. Process of restoring takes about two minutes.

6.2. Software factory settings restoring via NMS IPTool

NMS IPTool (version 1.23.4 or later) allows to restore factory settings. To restore settings find camera

via NMS IPTool, click right mouse button and choose “ Restore default configuration”. In 30 seconds

it is required to turn the camera power off and on.

RESTORING FACTORY DEFAULTS

NVIP-2SD-6100/20/F Quick start guide version 1.1

19

6.3. Hardware restoration of factory settings the IP camera

In order to restore factory defaults for the camera please follow the instructions:

• Unscrew the screws holding cover at the back of the dome

• Press the RESET button (when camera is powered) and hold on for about 10 seconds

• Release button

• Wait until the camera starts (finished positioning of the dome) - it takes abort 2 minutes

• Turn power off, mount cover back, turn the camera on

• Log in using default IP address (http://192.168.1.200) and default user name (root) and password

(pass)

RESTORING FACTORY DEFAULTS

microSD

RESET

2020-08-25 JZ MO (TF) v1.1

AAT SYSTEMY BEZPIECZEŃSTWA sp. z o.o.

431 Pulawska St., 02-801 Warsaw, Poland

tel.: +4822 546 07 00, fax: +4822 546 07 59

www.novuscctv.com

Strona jest ładowana ...

AAT NVIP-2SD-6100/20/F Instrukcja obsługi

AAT NVIP-2SD-6100/20/F Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty