Novus NVIP-5H-6202M-II Bullet IP Camera instrukcja

NVIP-5H-6202M-II

NVIP-5H-6202M-II/7043

Quick start guide

2

NVIP-5H-6202M-II Quick start guide version 1.0

2

IMPORTANT SAFEGUARDS AND WARNINGS

THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING DIRECTIVES:

Information

The device, as a part of professional CCTV system used for surveillance and control, is not designed

for self installation in households by individuals without technical knowledge.

Excluding of responsibility in case of damaging data on a disk or other devices:

The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other

devices during device operation.

WARNING!

PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN

PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE

PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE

PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF EXCLUDING

THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.

Pictures in this publication showing camera views can be simulations. Actual camera

images may vary depending on the type, model, settings, observation area, or

environmental conditions.

DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIMENT AND OF THE

COUNCIL of 26 February 2014 on the harmonisation of the laws of the Member States

relating to electromagnetic compatibility (OJ L 96, 29.3.2014, p. 79–106, with changes).

DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 4 July 2012 on waste electrical and electronic equipment WEEE)

(OJ L 197, 24.7.2012, p. 38–71,with changes).

DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 8 June 2011 on the restriction of the use of certain hazardous substances in

electrical and electronic equipment (OJ L 174, 1.7.2011, p. 88–110, with changes).

COMMISION DELEGATED DIRECTIVE (EU) 2015/863 of 31 March 2015 amending

Annex II to Directive 2011/65/EU of the European Parliament and of the Council as regards

the list of restricted substances.

DIRECTIVE (EU) 2017/2102 OF THE EUROPEAN PARLIAMENT AND OF THE

COUNCIL of 15 November 2017 amending Directive 2011/65/EU on the restriction of the

use of certain hazardous substances in electrical and electronic equipment.

3

NVIP-5H-6202M-II Quick start guide version 1.0

3

IMPORTANT SAFEGUARDS AND WARNINGS

WARNING!

THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER

DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH

THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.

WARNING!

USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER

-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL

MAY OPEN THE UNIT

INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE

PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS

1. Prior to undertaking any action please consult the following manual and read all the safety and

operating instructions before starting the device.

2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual

is necessary;

3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct

influence on user’s safety and durability and reliability of the device;

4. All actions conducted by the servicemen and users must be accomplished in accordance with the

user’s manual;

5. The device should be disconnected from power sources during maintenance procedures;

6. Usage of additional devices and components neither provided nor recommended by the producer is

forbidden;

7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools,

bath tubs, damp basements);

8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.)

is not recommended since it may lead to heat build-up and damaging the device itself as a

consequence;

9. Mounting the camera on unstable surface or using not recommended mounts is forbidden.

Improperly mounted camera may cause a fatal accident or may be seriously damaged itself. The

camera must be mounted by qualified personnel with proper authorization, in accordance with this

user’s manual.

10. Device should be supplied only from a power sources whose parameters are in accordance with

those specified by the producer in the camera technical datasheet. Therefore, it is forbidden to

supply the camera from a power sources with unknown parameters, unstable or not meeting

producer’s requirements;

Due to the product being constantly enhanced and optimized, certain parameters and functions

described in the manual in question may change without further notice.

We strongly suggest visiting the www.novuscctv.com/en website in order to access the newest full

manual

4

NVIP-5H-6202M-II Quick start guide version 1.0

4

TABLE OF CONTENTS ..................................................................................................... 4

1. FOREWORD INFORMATION ................................................................................... ..5

1.1. General characteristics ......................................................................................... 5

1.2. Technical specification .................................................................................... ...6

1.3. Camera dimensions ........................................................................................... ...7

1.4. Package contents ............................................................................................... ...7

2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................. 8

2.1. Description of connectors and control tools ........................................................ 8

2.2. Ethernet cable connecting ................................................................................... 9

2.3. Camera mounting .............................................................................................. 10

2.4. Starting the IP camera ........................................................................................ 11

2.5. Initial configuration via the web browser .......................................................... 12

2.6. Security recommendations for network architecture and configuration .......... 13

3. NETWORK CONNECTION USING WEB BROSWER ......................................... 14

3.1. Recommended PC specification for web browser ............................................. 14

3.2. Connection with IP camera via web browser ..................................................... 14

4. WWW INTERFACE - WORKING WITH IP CAMERA ......................................... 19

4.1. Displaying live video. ......................................................................................... 19

5. ELECTRIC CONNECTORS AND ACCESORIES ................................................. 20

5.1. MicroSD card installation ................................................................................. 20

6. FACTORY SETTINGS RESTORING ...................................................................... 21

6.1. Software factory settings restoring via web browser ......................................... 21

6.2. Software factory settings restoring via NMS IPTool……… ... ………………..21

6.3. Hardware factory settings restoring ...................... ………………..…………...22

TABLE OF CONTENTS

5

NVIP-5H-6202M-II Quick start guide version 1.0

5

1. FOREWORD INFORMATION

1.1. General Characteristics

• Sensor resolution: 5 megapixels

• Mechanical IR cut filter (IR operation capability)

• Min. Illumination from 0 lx with IR LED on

• Wide Dynamic Range (WDR) for enhanced image quality in diverse light conditions

• Digital Noise Reduction (DNR)

• Highlight Compensation (HLC)

• Back Light Compensation (BLC)

• Reduction of image flicker (Antiflicker)

• Lens type: motor-zoom, f = 2.8~12mm/F1.4

• Built-in LED illuminator

• Built-in webserver: camera configuration through the website

• Video compression: H.264, H.265, H.264+, H.265+, MJPEG / G711

• Max. video resolution up to 2880x1620

• Multi streaming: compression, resolution, speed and quality defined individually for each video

stream

• ROI functions

• Motion detection

• Private Zones

• RTSP protocol support for video transmission

• Schedule

• Micro SD card up to 256GB

• Wide range of responses to alarm events: e-mail with attachment, saving file on FTP server,

saving file on microSD card

• Electronic Shutter from 1/2 s to 1/100 000 s.

• Supports up to 3 streams

• ONVIF Protocol Support

• Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,

playback and remote IP devices administration

• Power supply: 12 VDC / PoE

FOREWORD INFORMATION

6

NVIP-5H-6202M-II Quick start guide version 1.0

6

1.2. Technical specification

FOREWORD INFORMATION

IMAGE

Image Sensor 5 MPX CMOS sensor 1/2.7” SmartSens

Number of Eecve Pixels 2884 (H) x 1624 (V)

Min. Illuminaon 0.005 lx/F1.4 - color mode, 0 lx (IR on) - B/W mode

Electronic Shuer auto/manual: 1/2 s ~ 1/100000 s

Digital Slow Shuer (DSS) up to 1/2 s

Wide Dynamic Range (WDR) yes 120dB

Digital Noise Reducon (DNR) 2D, 3D

Highlight Compensaon (HLC) yes

Back Light Compensaon (BLC) yes

Reducon of image icker (Anicker) yes

LENS

Lens Type motorized, auto-iris funcon, f=2.8 ~ 12 mm/F1.4

Auto-focus zoom trigger, day/night mode trigger, manual trigger

DAY/NIGHT

Switching Type mechanical IR cut lter

Switching Mode auto, manual, me

Switching Level Adjustment yes

Switching Delay 2 ~ 120 s

Switching Schedule yes

Visible Light Sensor yes

NETWORK

Stream Resoluon 2880 x 1620, 2560 x 1440 (QHD), 2304 x 1296, 1920 x 1080 (Full HD), 1280 x 720 (HD), 704

x 576, 704 x 480, 640 x 480 (VGA), 480 x 240, 352 x 288 (CIF), 352 x 240

Frame Rate 30 fps for each resoluon

Mulstreaming Mode 3 streams

Video/Audio Compression H.264, H.264+, H.265, H.265+, MJPEG/G.711

Number of Simultaneous Connecons max. 10

Bandwidth 60 Mb/s in total

Network Protocols Support HTTP, IPv4, IPv4/v6, UDP, HTTPS, FTP, DHCP, DDNS, NTP, RTSP, RTP, UPnP, SNMP, QoS,

IEEE 802.1X, PPPoE, SMTP, RTCP, RTMP

ONVIF Protocol Support Prole S

Camera Conguraon from Internet Explorer, Firefox, Chrome, Opera browser

languages: Polish, English, and others

Compable Soware NMS, N Control 6000

Mobile applicaons SuperLive Plus (iPhone, Android)

OTHER FUNCTIONS

Privacy Zones 4 video mask type: single color

Moon Detecon yes

Region of interest (ROI) 8

Video Content Analysis (VCA) abandoned object, object disappearance, line cross, Scene Change, intrusion detecon

Image Processing sharpening, mirror eect, corridor mode, vercal ip, horizontal ip

Prealarm/Postalarm up to 6 s/up to 120 s

System Reacon to Alarm Events e-mail, e-mail with aachment, saving le on FTP server, saving le on SD card

Restoring default sengs via web browser, using reset buon, via NMS IPTool soware

7

NVIP-5H-6202M-II Quick start guide version 1.0

7

FOREWORD INFORMATION

1.3. Camera dimensions (mm)

Camera NVIP-5H-6202M-II

1.4. Package contents

After opening the package make sure that the following elements are inside:

• IP camera

• Accessories bag

• Short version of user’s manual

If any of this elements has been damaged during transport, pack all the elements back into the original

box and contact your supplier for further assistance.

CAUTION!

It is forbidden to use – as the camera power source – PoE equipment (adapters, etc.) not

compatible with IEEE 802.3af standard (items called “passive PoE power supply”). Damages

caused by the usage of improper power supply source are not covered by the warranty.

81

220

IR LED

LED Number 2

Range 50 m

Smart IR yes (soware support)

INTERFACES

Audio Input/Output 1 x Jack (3.5 mm)/- built-in microphone

Network Interface 1 x Ethernet - RJ-45 interface, 10/100 Mbit/s

Memory Card Slot microSD - capacity up to 256GB

INSTALLATION PARAMETERS

Dimensions (mm) with bracket: 81 (W) x 81 (H) x 220 (L)

Weight 0.7 kg

Degree of Protecon IP 67 (details in the user’s manual)

Enclosure aluminium, white or grey (NVIP-5H-6202M-II/7043) , fully cable managed wall mount

bracket in-set included , IK10 impact rang

Power Supply PoE, 12 VDC

Surge protecon TVS 4000 V

Power Consumpon 5 W,

9 W (IR illuminator on)

Operang Temperature -30°C ~ 60°C

Humidity max. 95%, relave (non-condensing)

8

NVIP-5H-6202M-II Quick start guide version 1.0

8

START-UP AND INITIAL IP CAMERA CONFIGURATION

2. START-UP AND INITIAL IP CAMERA CONFIGURATION

CAUTION!

If the device was brought from a location with lower temperature, please wait until it reaches

the temperature of location it is currently in. Turning the device on immediately after bringing it

from a location with lower ambient temperature is forbidden, as the condensing water vapour

may cause short-circuits and damage the device as a result.

Before starting the device familiarize yourself with the description and the role of particular

inputs, outputs and adjusting elements that the device is equipped with.

2.1 Description of connectors and control tools

1. 100 Mb/s Ethernet port (PoE RJ-45 connector)

2. Audio input (Jack 3.5 mm)

3. Power supply 12VDC

4. Counter nut

5. Base of camera

6. MicroSD card slot

7. Reset button

1

3

7

6

4 5

2

9

NVIP-5H-6202M-II Quick start guide version 1.0

9

START-UP AND INITIAL IP CAMERA CONFIGURATION

2.2. Ethernet cable connecting

To maintain tightness of ethernet cable connection, please follow instruction below:

1. Unscrew the nut (1) from the connector cover (2).

2. Route the network cable (without the RJ-45 plug) through the components (1) and (2), than crimp the

RJ-45 connector.

3. Plug the RJ-45 connector into the hermetic socket (3), screw the connector cover (2), and than the

nut (1).

CAUTION!

The declared degree of protection of the camera relates to its housing and does not take into

account the possibility of moisture infiltration into the camera by connection cables. Connection

cables protection through i.e. sealing up is the camera installer duty. The manufacturer is not

liable for any camera damages caused as a result of failing in performing that activity by

installer, which also means that camera damaged in that way is not subject to warranty repairs.

CAUTION!

Camera power supply connector is not hermetic. Installer should seal this connector by himself.

Camera can be supplied using external power supply unit corresponding with the camera parameters or

by using RJ45 network socket and PoE (802.3af) power supply unit. If you’re using external power

supply please connect wires according to polarisation shown on picture:

CAUTION!

In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge

protectors is advised. Any damages resulting from surges are not eligible for service repairs.

12 VDC +

GND

Scheme of 12VDC power supply connector

1 2

3

1

2

10

NVIP-5H-6202M-II Quick start guide version 1.0

10

2.3. Camera mounting

To mount a camera please follow the instructions below:

• Unscrew the counter nut (2).

• Put the bracket to the wall in a desired mounting place (with cable hole). Take the drill pattern

and mark future drilling holes for screws and wires.

• Drill holes for screws, wires and base.

• Mount the camera base (1) using the supplied plugs and screws.

• If necessary, unscrew the service panel (3), mount microSD card in the socket (4) and screw

the camera service panel (3).

• Connect the camera wires.

• Adjust camera position.

• Tighten to the stop counter nut (2).

CAUTION!

Please note that the wall or ceiling must have enough strength to carry the IP Camera.

CAUTION!

In order to obtain declared degree of protection please seal the camera bracket to prevent water

getting inside. Furthermore, when installing the bracket on rough/uneven surfaces, please

additionally seal the junction with appropriate sealing mass. Please pay special attention to any

mounting holes and if they are a loop-through ones, seal them too.

START-UP AND INITIAL CAMERA CONFIGURATION

1 2

3 4

11

NVIP-5H-6202M-II Quick start guide version 1.0

11

2.4. Starting the IP camera

To run NOVUS IP camera you have to connect ethernet cable between camera and network PoE switch

with PoE support (IEEE 802.3af).

You can also power it from 12VDC power supply compatible with camera power supply specification.

The recommended way to start an IP camera and perform its configuration is a direct connection to the

network switch which is not connected to other devices. To obtain further information about network

configuration parameters (IP address, gateway, network mask, etc.) please contact your network

administrator.

• Connection using network switch with PoE support

• Connection using external power supply and network switch

START-UP AND INITIAL CAMERA CONFIGURATION

Power supply and

network transmission

Computer

IP Camera

Network PoE Switch

Network transmission

IP Camera

Network transmission

Network Switch Computer

Network transmission

12

NVIP-5H-6202M-II Quick start guide version 1.0

12

• Connection using external power supply directly to the computer

Information:

Power supply adapter is not included. Please use power adapter with parameters specified in user ‘s

manual.

2.5. Initial configuration via the web browser

The default network settings for NVIP-5H-6202M-II camera are :

1. IP address= 192.168.1.200

2. Network mask - 255.255.255.0

3. Gateway - 192.168.1.1

4. User name - root

5. Password - pass

Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can

operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from

192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for

camera and PC computer.

You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera

yourself or select DHCP mode (DHCP server is required in this method in target network) by using

web browser or by NMS software. When you use DHCP server check IP address lease and its linking

with camera MAC address to avoid changing or losing IP address during device operation or network/

DHCP server breakdown. You have to remember to use a new camera IP address after changing

network parameters.

After network setting configuration has been done, the camera can be connected to a target network.

START-UP AND INITIAL CAMERA CONFIGURATION

IP Camera

Network transmission - cross over cable

Computer

13

NVIP-5H-6202M-II Quick start guide version 1.0

13

2.6. Security recommendations for network architecture and configuration

CAUTION!

Below are shown security recommendations for network architecture and configuration

of CCTV systems that are connected to the Internet to reduce the risk

of unauthorized interference with the system by a third party.

1. Absolutely change the default passwords and user names (if the device gives this possibility) of

all applied network devices (recorders, cameras, routers, network switches, etc.) to the

severely complexity password. Use lowercase and uppercase letters, numbers, and special characters

if there is such possibility.

2. Depending on the available functionality in the order to restrict access to the used network devices at

the administrator account level, it is recommended to configure the users accounts accordingly.

3. Do not use DMZ function (Demilitarized zone) in your router. Using that function you open the

access to recorder system from the Internet on all ports, which gives possibility for an unauthorized

interference with the system.

Instead of DMZ use port forwarding redirect only the ports which are necessary for the performance

of the connection (detailed information about ports of communication in different models of recorders,

cameras, etc. can be found in the operating instructions).

4. Use routers with firewall function and make sure it is enabled and properly configured.

5. It is recommended to change the default network communication port numbers of used devices

if there is such possibility.

6. If used network devices has a UPnP feature and it is not used, turn it off.

7. If used network devices has a P2P feature and it is not used, turn it off.

8. If used network devices support HTTPS protocol for connection, it is recommended to use it.

9. If used network devices support IP filtering for authorized connections function, it is recommended

to use it.

10. If used recorder has two network interfaces it is recommended to use both of them to physically

separate network for cameras and network for Internet connection. The only device in the system,

accessible from Internet will be recorder - there will be no physically access directly to any camera.

START-UP AND INITIAL CAMERA CONFIGURATION

14

NVIP-5H-6202M-II Quick start guide version 1.0

14

3. NETWORK CONNECTION USING WEB BROSWER

3.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming smooth image display

in 2880x1620 resolution and 30 fps speed.

1. CPU Intel i7 3 GHz

2. RAM Memory min. 6 GB

3. VGA card Nvidia GeForce 1GB

4. Operating System Windows 10

5. Network card 100/1000 Mb/s

3.2. Connection with IP camera via web browser

• Connecting to the camera for the first time

Enter the IP address of the camera (default 192.168.1.200) in the address bar of the web browser. If the

address is correct and the target device is currently available, the first connection window will be

displayed. In this window, user should read the privacy statement and after reading it, select the

checkbox next to the Already Read button, and press this button.

The acceptance of the privacy statement cannot be omitted. This window only appears the first time

you log in, but it can be displayed again at any time.

Access to the privacy statement can be found in the menu Config > System > Basic information >

Privacy statement.

NETWORK CONNECTION USING WEB BROWSER

15

NVIP-5H-6202M-II Quick start guide version 1.0

15

3. NETWORK CONNECTION USING WEB BROSWER

3.1. Recommended PC specification for web browser connections

Requirements below apply to connection with an IP camera, assuming smooth image display

in 2592x1520 resolution and 30 fps speed.

1. CPU Intel i7 3 GHz

2. RAM Memory min. 6 GB

3. VGA card Nvidia GeForce 1GB

4. Operating System Windows 10

5. Network card 100/1000 Mb/s

3.2. Connection with IP camera via web browser

• Connecting to the camera for the first time

Enter the IP address of the camera (default 192.168.1.200) in the address bar of the web browser. If the

address is correct and the target device is currently available, the first connection window will be

displayed. In this window, user should read the privacy statement and after reading it, select the

checkbox next to the Already Read button, and press this button.

The acceptance of the privacy statement cannot be omitted. This window only appears the first time

you log in, but it can be displayed again at any time.

Access to the privacy statement can be found in the menu Config > System > Basic information >

Privacy statement.

NETWORK CONNECTION USING WEB BROWSER

• Device Activation

After accept privacy statement, device activate window appears. In this window user has to set a

password for the web account.

Check the "Activate Onvif user" checkbox to change the password for the Onvif account to the same

password as for the web account.

The password can be up to 16 characters long. While password is entered strength of it displaing on

an ongoing basis by the security level indicator. To ensure the good security of the password, use upper

and lower case letters, numbers and special characters. After entering the correct password twice and

confirming it with the OK button, the administrator password will be saved, the window will close and

the login screen will be displayed.

• User accounts

The Web account is the administrator account created during the activation of the device. It means that

the user logging in, by using the root login and a predefined password and have access to the full

functionality and all available settings in the camera. The account is also used to log in to the camera

via the 6000 series network recorders and NMS (Novus Management System) software using the

LongPolling event method.

The Onvif account is an account used to log in to the camera via the NMS software (Novus

Management System) or using the Onvif or the RTSP protocol. This account is created automatically

during activation of the device, and the default login data are login: "root" and password: "pass".

NETWORK CONNECTION USING WEB BROWSER

For security reasons, immediately change the default password for the Onvif account after

activating the device. It is recommended to set the same password in both accounts: the Onvif

account and the web account.

If the user assigns a new password during the device activation but does not check the

"Activate Onvif User" checkbox, the Onvif account will remain with the default login data

(login: root and password: pass).

16

NVIP-5H-6202M-II Quick start guide version 1.0

16

• Onvif account edition

In order to change the Onvif account password, after logging in, go to the Settings tab in the upper

right corner and then Network > Onvif.

In the Onvif tab, click the Modify button, then in the Edit User window, enter the new password and

confirm with OK button. If the connection to the camera via the NMS software is using the

LongPolling event handling method, the same password for the Onvif account as for the Web account

must be set in this step.

In order to delete the Onvif account, select the user by clicking on the appropriate row in the table, then

click Delete button. Please note that deleting Onvif account means that the camera cannot be added to

NMS software. Add button is used to create new Onvif account.

• Logging in to the camera for the first time

In this window, in order to login to camera, enter the user name root and the newly set administrator

password. In the Stream type field user can select the stream that is displayed in the live view window

after login. The Language field allows to change the interface language. The Forget Password option

allows to log in to the camera if you forget the administrator password and for this is required to know

the answers to the security questions (set in the next step).

After entering appropriate data, click the Login button to login to the web panel of the camera.

NETWORK CONNECTION USING WEB BROWSER

17

NVIP-5H-6202M-II Quick start guide version 1.0

17

• Safety questions

The next step in logging in for the first time is

entering answers to the security questions.

In the window that appears, select questions

from among those available on the list and enter

your own answers.

Knowing the right answers is essential to

recovering the administrator password.

• Plug-in installation

If the browser has no connected to any of the 6000 series cameras so far, or if an older version of the

plug-in is installed, a message will be displayed in the remote viewing window that the appropriate

plug-in version must be installed.

NETWORK CONNECTION USING WEB BROWSER

This step cannot be omitted. The security question window is displayed only during the first

login, and the only possibility to change the given answers is to restore the factory settings and

go through all stages of the first connection with the camera.

18

NVIP-5H-6202M-II Quick start guide version 1.0

18

To start plug-in installation, click Here button. Then the browser displays a window asking how to

proceed with the NetAIIPCamera.exe file. Press the Run button to start the plug-in installer.

In the installer window, select the installation language (English by default) and then click Install

button to install plug-in. After installation click the Finish button to close the installer and refresh the

browser window (you can also close and restart the browser).

If after installation and browser window refresh, the same text appears on the screen, go to the browser

Tools (the gearwheel icon in the top right corner), then click Menage add-ones. In the window that

appears click right mouse button on the NetAIIPCamera Control, then click the Enable option and

refresh the browser window.

After completion all of the above steps, preview of the camera in the live view window should appears.

NETWORK CONNECTION USING WEB BROWSER

19

NVIP-5H-6202M-II Quick start guide version 1.0

19

4. WWW INTERFACE - WORKING WITH IP CAMERA

4.1 Displaying live video

1. Camera menu:

• Live - opens the camera live video,

• Config - opens the camera configuration menu,

• Search - opens the camera playback.

2. The buttons for changing the displayed stream and fluency:

Allow to change the displayed stream to Main stream, Sub stream.

Allow you to choose between Real-time, Balanced and Fluent fluency.

3. Alarm icons - icons showing the current status of some camera alarms.

4. Live video window

5. Image settings buttons - these buttons change the picture display mode in the live video preview

Original size Adapt

Proper size Full screen

WWW INTERFACE - WORKING WITH IP CAMERA

6

4

3

1

5

2

20

NVIP-5H-6202M-II Quick start guide version 1.0

20

6. Function buttons:

Start/stop live view Enable/disable audio

Snapshot Start Recording

Zoom In (digital) Zoom out (digital)

Lens control

5. ELECTRIC CONNECTORS AND ACCESORIES

5.1. MicroSD card installation

Camera supports microSD cards up to a maximum size of 256GB. In order to install the card

properly, please follow the instructions below:

• Turn off the camera power.

• Unscrew the camera service panel (1).

• Mount microSD card in the socket (2).

• Screw the camera service panel (1).

• Turn on the camera.

• Check the microSD card by checking its capacity in the “System” -> “SD Card” tab.

ELECTRIC CONNECTORS AND ACCESORIES

1 2

Enable/disable graphical representation

of image analysis

Strona jest ładowana ...

Novus NVIP-5H-6202M-II Bullet IP Camera instrukcja

Novus NVIP-5H-6202M-II Bullet IP Camera instrukcja

w innych językach

Powiązane dokumenty

Inne dokumenty