Panasonic NVGS500 Instrukcja obsługi

EP

Operating Instructions

Instrukcja obsługi

Digital Video Camera

Model No. NV-GS500

Before use, please read these instructions completely.

Przed pierwszym włączeniem kamery prosimy o dokładne przeczytanie

instrukcji obsługi.

VQT0T39

VQT0T39_EP_eng.book 1 ページ２００５年１２月２６日　月曜日　午後８時７分

2

VQT0T39

Information for your safety

ª Carefully read the Operating

Instructions and use the Movie

Camera correctly

≥Injury or material damage resulting from any

kind of use that is not in accordance with the

operating procedures explained in these

Operating Instructions are the sole

responsibility of the user.

Try out the Movie Camera.

Be sure to try out the Movie Camera before

recording your first important event and check

that it records properly and functions correctly.

The manufacturer is not liable for loss of

recorded contents.

The manufacturer shall in no event be liable for

the loss of recordings due to malfunction or defect

of this Movie Camera, its accessories or

cassettes.

Carefully observe copyright laws.

Recording of pre-recorded tapes or discs or other

published or broadcast material for purposes

other than your own private use may infringe

copyright laws. Even for the purpose of private

use, recording of certain material may be

restricted.

≥The Movie Camera uses copyright-protected

technologies and is protected by the patented

technologies and intellectual properties of

Japan and the U.S. To use these copyright-

protected technologies, authorization of the

Macrovision Company is required. It is

prohibited to disassemble or modify the Movie

Camera.

≥SD Logo is a trademark.

≥Leica is a registered trademark of Leica

Microsystems IR GmbH and Dicomar is a

registered trademark of Leica Camera AG.

≥All other company and product names in the

operating instructions are trademarks or

registered trademarks of their respective

corporations.

Files recorded on SD Memory Card

It may not be possible to play back the files on

this Movie Camera recorded on and created by

other equipment or vice versa. For this reason,

check the compatibility of the equipment in

advance.

≥Keep the Memory Card out of reach of children

to prevent swallowing.

Pages for reference

Pages for reference are indicated by dashes

either side of a number, for example:

-00-

The menu operation flow is indicated by >> in the

description.

ª Warning

To prevent electric shock, do not remove the

cover (or back); there are no user serviceable

parts inside.

Refer servicing to qualified service personnel.

ª EMC Electric and magnetic

compatibility

This symbol (CE) is located on the rating

plate.

Use only the recommended accessories.

≥Do not use any other Multi cables and USB

cables except the supplied one.

≥When you use the cable which are sold

separately, please make sure to use the one

whose length is less than 3 metres.

As this equipment gets hot during use,

operate it in a well-ventilated place; do

not install this equipment in a confined

space such as a bookcase or similar unit.

To reduce the risk of fire, electric shock

or product damage, do not expose this

equipment to rain, moisture, dripping or

splashing and ensure that no objects

filled with liquids, such as vases, shall be

placed on the equipment.

AC Adaptor

≥The rating plate is on the underside of

the AC Adaptor.

VQT0T39_EP_eng.book 2 ページ２００５年１２月２６日　月曜日　午後８時７分

3

VQT0T39

Information on Disposal for Users of

Waste Electrical & Electronic Equipment

(private households)

This symbol on the

products and/or

accompanying

documents means

that used electrical

and electronic

products should not

be mixed with

general household

waste.

For proper

treatment, recovery

and recycling, please take these products to

designated collection points, where they will

be accepted on a free of charge basis.

Alternatively, in some countries you may be

able to return your products to your local

retailer upon the purchase of an equivalent

new product.

Disposing of this product correctly will help to

save valuable resources and prevent any

potential negative effects on human health

and the environment which could otherwise

arise from inappropriate waste handling.

Please contact your local authority for further

details of your nearest designated collection

point.

Penalties may be applicable for incorrect

disposal of this waste, in accordance with

national legislation.

For business users in the European

Union

If you wish to discard electrical and

electronic equipment, please contact your

dealer or supplier for further information.

Information on Disposal in other

Countries outside the European Union

This symbol is only valid in the European

Union.

If you wish to discard this product, please

contact your local authorities or dealer and

ask for the correct method of disposal.

ENGLISH

VQT0T39_EP_eng.book 3 ページ２００５年１２月２６日　月曜日　午後８時７分

4

VQT0T39

Contents

Information for your safety ................................... 2

Before using

Accessories.......................................................... 5

Optional................................................................ 5

Parts identification and handling .......................... 5

Fitting the lens cap............................................... 8

The one-touch free-style grip belt ........................ 8

Power supply ....................................................... 9

Charging time and recordable time .................... 10

Turning the movie camera on ............................ 10

Setting date and time ......................................... 11

Using the LCD monitor....................................... 12

Using the viewfinder........................................... 12

Quick Start ......................................................... 13

Inserting/removing a cassette ............................ 14

Inserting/removing a card .................................. 15

Selecting a mode ............................................... 16

How to use the joystick ...................................... 16

Help mode.......................................................... 18

Switching the language...................................... 18

Using the menu screen ...................................... 18

Adjusting LCD monitor/viewfinder...................... 20

Using the remote control.................................... 21

Free style remote control ................................... 23

Record mode

Check before recording...................................... 24

Recording on a tape........................................... 25

Recording check ................................................ 26

Blank search function......................................... 26

Recording still pictures on a card

while recording image onto a tape .................. 26

Recording still pictures onto a card

(Photoshot)...................................................... 27

Zoom in/out function .......................................... 29

Recording yourself ............................................. 30

Backlight compensation function ....................... 30

Colour night view functions ................................ 30

Soft skin mode ................................................... 31

Tele macro function ........................................... 31

Fade in/fade out function ................................... 31

Wind noise reduction function............................ 32

Adjusting the Microphone Sensitivity Level........ 32

Anti-Ground-Shooting (AGS) ............................. 33

Using the built-in video flash .............................. 33

Self-timer recording............................................ 35

Wide/Pro-Cinema Function ................................ 35

Image stabilizer function .................................... 36

Continuous Photoshot........................................ 36

Recording in various situations

(Scene mode).................................................. 37

Recording in natural colours

(White balance) ............................................... 38

Manual focus adjustment ................................... 39

Manual shutter speed/aperture adjustment........ 39

Playback mode

Playing back tape............................................... 41

Slow-motion playback/

frame-by-frame playback................................. 42

Variable-speed search function.......................... 42

Playback on TV .................................................. 43

Playing back card............................................... 43

Deleting files recorded on a card ....................... 44

Formatting a card............................................... 45

Protecting files on a card.................................... 46

Writing the printing data on a card

(DPOF setting) ................................................ 46

Edit mode

Recording from a tape onto a card..................... 47

Copying onto a DVD recorder or a VCR

(Dubbing)......................................................... 47

Using the DV Cable for Recording

(Digital Dubbing)............................................. 48

Audio dubbing .................................................... 49

Printing pictures by directly connecting

to the printer (PictBridge) ................................ 50

Menu

Menu list............................................................. 52

Menus related to recording ................................ 54

Menus related to playback ................................. 55

Other menus ...................................................... 55

Others

Indications.......................................................... 56

Warning/alarm indications.................................. 57

Functions that cannot be used

simultaneously................................................. 58

Before requesting repair

(Problems and solutions)................................. 59

Cautions for Use ................................................ 62

Explanation of terms .......................................... 66

Specifications

Specifications..................................................... 68

VQT0T39_EP_eng.book 4 ページ２００５年１２月２６日　月曜日　午後８時７分

Before using

5

VQT0T39

Before using

Accessories

The followings are the accessories supplied with

this product.

1) AC adaptor, DC input lead, AC mains lead

-9-

2) Battery pack -9-

3) Remote control, button-type battery -21-

4) Free style remote control -23-

5) Lens cap -8-

6) Multi cable -47-

7) Shoulder strap -7-

8) USB cable and CD-ROM -50-

Optional

1) AC adaptor (VW-AD11E)

2) Battery pack (lithium/CGR-DU06/640mAh)

3) Battery pack (lithium/CGA-DU07/680mAh)

4) Battery pack (lithium/CGA-DU12/1150mAh)

5) Battery pack (lithium/CGA-DU14/1360mAh)

6) Battery pack (lithium/CGA-DU21/2040mAh)

7) Wide conversion lens (VW-LW4307ME)

8) Tele conversion lens (VW-LT4314NE)

9) Filter kit (VW-LF43WE)

10) Video DC light (VW-LDC10E)

11) Video DC light (VW-LDH3E)

12) Light bulb for video DC light (VZ-LL10E)

13) Light bulb for video DC light (VW-LL3E)

14) Stereo zoom microphone (VW-VMH3E)

15) Stereo microphone (VW-VMS2E)

16) Video flash (VW-FLH3E)

17) Tripod (VW-CT45E)

18) DV cable (VW-CD1E)

19) Jacket pouch (VW-SJ05E)

≥Some optional accessories may not be

available in some countries.

Parts identification and handling

ª Camera

(1) Built-in video flash -33-

(2)

White balance sensor -38-

Remote control sensor -22-

(3)

Recording lamp -54-

(4)

Grip belt

(One-touch free-style grip belt)

-8-

(5)

Lens (LEICA DICOMAR)

(6) Microphone (built-in, stereo) -29-, -32-

(7)

Speaker -41-

(8)

Audio-video/S-Video output terminal

[A/V]

-47-

≥Use the supplied Multi cable only, otherwise

audio may not be played back normally.

(9) Terminal for free style remote control

[REMOTE]

-23-

Microphone terminal [MIC]

≥A compatible plug-in powered microphone

can be used as an external microphone.

≥When the movie camera is connected with

AC adaptor, sometimes noise may be heard

depending on microphone type. In that

case, please switch to battery for power

supply and noise will stop.

K2GJ2DZ00018

1)

2)

6)

7)

VFC3506-1A

3)

VYF2992

5)

4)

8)

CR2025

N2QAEC000017

K2KZ9CB00001

N2QCAD000007

VFA0453

K2CQ2CA00006

VSK0651B

(4)

(1)

(2)

(3)

(5)

(6)

A/V

REMOTE/MIC

(7)

(8)

(9)

VQT0T39_EP_eng.book 5 ページ２００５年１２月２６日　月曜日　午後８時７分

Before using

6

VQT0T39

(10) Viewfinder -12-, -66-

(11)

Battery holder -9-

(12)

Battery release lever [BATT] -9-

(13)

Power switch [OFF/ON] -10-

(14)

Status indicator -10-

(15)

Menu button [MENU] -18-

(16)

Joystick -16-

(17)

Mode dial -16-

(18)

Recording start/stop button -25-

(19)

Focus ring -39-

(20)

LCD monitor -12-, -66-

(21) LCD monitor open part [OPEN] -12-

(22)

Mode select switch [AUTO/MANUAL/

FOCUS]

-24-, -37-, -39-

(23)

Power LCD button [POWER LCD] -20-

(24)

USB terminal [ ] -50-

(25)

DV input/output terminal [DV] -48-

(26)

Reset button [RESET] -62-

(27)

Card access lamp -15-

(28)

Card slot -15-

(29)

Card slot cover -15-

(30)

Cassette holder -14-

(31)

Cassette eject lever [OPEN/EJECT] -14-

(32)

Cassette cover -14-

(33)

Zoom lever [W/T] -29-

Volume lever [s /VOLr] -41-

(34)

Photoshot button [PHOTO SHOT] -26-

Due to limitations in LCD production

technology, there may be some tiny bright or

dark spots on the Viewfinder screen.

However, this is not a malfunction and does

not affect the recorded picture.

BATT

(10)

(11)

(12)

(13)

(14)

(15)

(16)

(17)

(18)

Due to limitations in LCD production

technology, there may be some tiny bright or

dark spots on the LCD monitor screen.

However, this is not a malfunction and does

not affect the recorded picture.

(19)

(20)

(21)

(22)

(23)

(24)

(25)

(26)

(27)

(28)

(29)

(30)

(31)

(32)

(33)

(34)

VQT0T39_EP_eng.book 6 ページ２００５年１２月２６日　月曜日　午後８時７分

Before using

7

VQT0T39

(35) Tripod receptacle

This is a hole for attaching the camera to optional

tripod/VW-CT45E. (Please carefully read the

operating instructions for how to attach the tripod

to the camera.)

≥When the tripod is used, operate the camera

from the free style remote control for

convenience. (When not using the remote

control, attach the clip to the grip belt for

convenience. When you move with remote

control attached to a pocket, etc., take care to

avoid falling of the tripod.)

≥You cannot open the card slot cover when the

tripod is used. Insert the card first and then

attach the tripod.

(36) Shoulder strap fixture

This is a fixture for attaching the shoulder strap to

hang the camera from your neck or shoulder.

≥Put the strap through the fixture 1 and through

the stopper 2 so it will not come off. Extend

part 3 by at least 2 cm.

≥Fit the other end of the belt similarly.

(37) Lens hood

In order to remove the lens hood, rotate it

counterclockwise 1. In order to fit it, put into slot

2, and then rotate it clockwise.

≥Fit the MC protector or the ND filter of the Filter

Kit (VW-LF43WE; optional) in front of the lens

hood. Do not fit the other accessories on the

hood. (Except for the lens cap)

(Refer to the operating instructions for the Filter

Kit.)

≥When fitting the tele conversion lens

(VW-LT4314NE; optional) or the wide

conversion lens (VW-LW4307ME; optional), first

remove the lens hood.

(Refer to the operating instructions for the tele

conversion lens or the wide conversion lens.)

≥When 2 lens accessories, such as the ND filter

and tele conversion lens, are fitted and the

[W/T] lever is pressed toward the [W] side, the 4

corners of an image will be darkened.

(Vignetting)

(38) Smart accessory shoe

The stereo zoom microphone /VW-VMH3E

(optional) or the video DC light/VW-LDH3E

(optional) should be mounted here.

≥When mounting or removing the accessory,

extend the viewfinder (1).

≥When using an accessory for the smart

accessory shoe, the power is supplied from this

product.

(35)

(36)

2

3

1

1 2

(37)

1

(38)

VQT0T39_EP_eng.book 7 ページ２００５年１２月２６日　月曜日　午後８時７分

Before using

8

VQT0T39

Fitting the lens cap

Fit the lens cap to protect the surface of the lens.

1 Push the string through the belt. Push the

lens cap through the loop in the string.

≥To fit or remove the lens cap, hold both sides of

the lens cap with the tips of your first 2 fingers.

≥The lens cap removed can be hung on the lens

cap fixture. (It cannot be hung if the grip belt is

used as a hand strap.)

The one-touch free-style grip belt

ª To use as a grip belt

Adjust the belt length so it fits your hand.

1 Adjust the belt length and the pad position.

1 Flip the belt.

2 Adjust the length.

3 Fix the belt.

ª

To use as a hand strap

If you use the grip belt as a hand strap, then you

can carry or handle this camera more easily.

1 Flip the belt.

2 Adjust the length.

2 Put your hand through the strap.

≥Use the free style remote control for more

convenience.

≥Hold the movie camera in a way that the

microphones or sensors are not covered with

your hands.

1

3

2

1

2

VQT0T39_EP_eng.book 8 ページ２００５年１２月２６日　月曜日　午後８時７分

Before using

9

VQT0T39

Power supply

ª Charging the battery

When this product is purchased, the battery is not

charged. Charge the battery before using this

product.

≥Battery charging time (

-10-)

≥We recommend using Panasonic batteries.

≥If you use other batteries, we cannot guarantee

the quality of this product.

≥If the DC input lead is connected to the AC

adaptor, then the battery will not get charged.

Remove the DC input lead from the AC adaptor.

1 Connect the AC mains lead to the AC

adaptor and the AC mains socket.

2 Put the battery on the battery mount by

aligning the mark, and then securely plug it

in.

ª

Charging lamp

Lights up:Charging

Goes off: Charging completed

Flashing: The battery is over discharged

(discharged excessively). In a while,

the lamp will light up and normal

charging will start.

When the battery temperature is

excessively high or low, the [CHARGE]

lamp flashes and the charging time will

be longer than normal.

ª

Connecting to the AC outlet

1 Connect the AC mains lead to the AC

adaptor and the AC mains socket.

2 Connect the DC input lead to the AC

adaptor.

3 Connect the DC input lead to this product.

≥The output plug of the AC mains lead is not

completely connected to the AC adaptor

socket. As shown in 1, there is a gap.

≥Do not use the power cord for other

equipment since the power cord is exclusively

designed for the movie camera. Or do not use

the power cord of other equipment for the

movie camera.

ª

Fitting the battery

Push the battery against the battery holder and

slide it until it clicks.

ª

Removing the battery

While sliding the [BATT] lever, slide the battery

(or the DC input lead) to remove it.

≥Hold the battery with your hand so it does not

fall.

≥Before removing the battery, be sure to set the

[OFF/ON] switch to [OFF].

1

BATT

VQT0T39_EP_eng.book 9 ページ２００５年１２月２６日　月曜日　午後８時７分

Before using

10

VQT0T39

Charging time and recordable time

The times shown in the tables below are for when

the temperature is 25 oC and the humidity is 60%.

If the temperature is higher or lower than 25 oC,

the charging time will become longer.

A Charging time

B Maximum continuously recordable time

C Intermittent recordable time

(The intermittent recordable time refers to

recordable time when the recording and stopping

operations are repeated.)

“1 h 5 min” indicates 1 hour 5 minutes.

≥The battery CGA-DU14 is supplied.

≥The charging time and recordable time shown in

the table are approximations. The times indicate

the recordable times when the viewfinder is

used. The times in parentheses indicate the

recordable times when the LCD monitor is used.

≥We recommend the Battery Pack CGA-DU14

and CGA-DU21 for long time recording (2 hours

or more for continuous recording, 1 hour or

more for intermittent recording).

≥The recordable time will become shorter in the

following cases:

≥When you use both the viewfinder and the

LCD monitor simultaneously while rotating

the LCD monitor frontward to record yourself,

using the 0 lux colour night view function, etc.

≥When you use this camera with the LCD

monitor lit up by pressing the [POWER LCD]

button.

≥When you use accessories fitted on the

camera’s smart accessory shoe such as the

stereo zoom microphone and video DC light,

etc.

≥The batteries heat up after use or charging. The

main unit of the movie camera being used will

also heat up. This is normal.

≥Along with the reduction of the battery capacity,

the display will change: # #

# # . If the battery

discharges, then ( ) will flash.

Turning the movie camera on

When the movie camera is turned on with the lens

cap fitted, the automatic white balance

adjustment (

-66-) may not function properly.

Please turn the movie camera on after removing

the lens cap.

ª

How to turn on the power

1 While pressing the button 1, set the

[OFF/ON] switch to [ON].

≥The Status indicator lights red and the power

turns on.

≥In Tape Recording Mode or Card Recording

Mode, if the [OFF/ON] switch is set to [ON]

while the LCD monitor is closed and the

viewfinder is retracted, the power turns off.

ª

How to turn off the power

1 While pressing the button 1, set the

[OFF/ON] switch to [OFF].

Supplied

battery/

CGA-DU14

(7.2 V/

1360 mAh)

A 2 h 45 min

B 2 h 10 min

(2 h 10 min)

C 1 h 5 min

(1 h 5 min)

CGA-DU21

(7.2 V/

2040 mAh)

A 3 h 55 min

B 3 h 15 min

(3 h 15 min)

C 1 h 40 min

(1 h 40 min)

CGR-DU06

(7.2 V/

640 mAh)

A 1 h 40 min

B 1 h 5 min

(1 h)

C 35 min

(30 min)

CGA-DU07

(7.2 V/

680 mAh)

A 1 h 30 min

B 1 h 5 min

(1 h 5 min)

C 35 min

(30 min)

CGA-DU12

(7.2 V/

1150 mAh)

A 2 h 25 min

B 1 h 55 min

(1 h 50 min)

C 1 h

(55 min)

OFF

ON

1

OFF

ON

1

VQT0T39_EP_eng.book 10 ページ２００５年１２月２６日　月曜日　午後８時７分

Before using

11

VQT0T39

≥Set the [OFF/ON] switch to [OFF] when not

using the movie camera.

≥The Status indicator goes off when the power

turns off.

ª

How to turn the power on and off with

the LCD monitor/viewfinder

When the power switch is set to [ON], the power

can be turned on and off with the LCD monitor

and the viewfinder when the unit is in Tape

Recording Mode or Card Recording Mode.

1 Open the LCD monitor out or extend the

viewfinder to use. (

-12-)

≥The LCD monitor or viewfinder will be

activated.

2 Close the LCD monitor and retract the

viewfinder.

≥The power will not turn off unless the LCD

monitor is closed and the viewfinder is

retracted.

≥The Status indicator automatically goes off

and the power turns off. (If quick start is set to

[ON] (

-13-), the unit goes into quick start

standby mode and the Status indicator lights

green.)

≥The power does not turn off even if the

LCD monitor is closed and the viewfinder

is retracted while recording on a tape.

3 Open the LCD monitor or extend the

viewfinder to turn the power on and use the

movie camera again.

≥The Status indicator lights red and the power

turns on.

Setting date and time

When the movie camera is turned on for the first

time, [SET DATE AND TIME] will appear.

≥Select [YES] and press the centre of the

joystick. Do steps 2 and 3 below to set the date/

time.

If the screen shows the incorrect date/time, then

adjust it.

≥Set to Tape Recording Mode or Card

Recording Mode.

1 Set [BASIC] >> [CLOCK SET] >> [YES].

(

-18-)

2 Move the joystick left or right in order to

select the item to be set. Then move the

joystick up or down to set the desired value.

≥The year will change as follows:

2000, 2001, ..., 2089, 2000, ...

≥The 24-hour clock is used.

3 Press the joystick to determine the setting.

≥The clock function starts at [00] seconds.

OFF

ON

OFF

ON

OFF

ON

VQT0T39_EP_eng.book 11 ページ２００５年１２月２６日　月曜日　午後８時７分

Before using

12

VQT0T39

ª About date/time

≥The date and time function are driven by a built-

in lithium battery.

≥Make sure to check the time before recording

because the built-in clock is not very accurate.

ª

Recharging the built-in lithium battery

≥If [0] or [--] appears when the camera is

turning on, then the built-in lithium battery has

run down. Use the steps below to charge the

battery. When turn on the power for the first time

after charging, [SET DATE AND TIME] will

appear. Select [YES] and set the date and time.

Connect the AC adaptor to the camera or attach

the battery to the camera, and the built-in lithium

battery will be recharged. Leave the camera as

is for approx. 24 hours, and the battery will drive

the date and time for approx. 6 months. (Even if

the [OFF/ON] switch is set to [OFF], the battery

is still being recharged.)

Using the LCD monitor

You can record the image while viewing it on the

opened LCD monitor.

1 Place your finger on OPEN and pull the LCD

monitor out in the direction of the arrow.

≥It can open up to 90o.

2 Adjust the angle of the LCD monitor as you

prefer.

≥It can rotate up to 180o 1 towards the lens or

90o 2 towards the viewfinder.

≥The brightness and colour level of the LCD

monitor can be adjusted from the menu.

≥If it is forcibly opened or rotated, the camera

may be damaged or fail.

≥If the LCD monitor is rotated by 180o towards

the lens and the viewfinder is extended (when

recording yourself), the LCD monitor and the

viewfinder simultaneously light.

Using the viewfinder

ª Extending the viewfinder

1 Pull out the viewfinder and extend it by

pinching the extension knob.

≥The viewfinder will be activated. (If the LCD

monitor is opened, the viewfinder will be

deactivated.)

ª

Lifting up the viewfinder

1 Lift it up by pinching the viewfinder

extension knob.

ª

Adjusting the field of view

1 Adjust the focus by sliding the eyepiece

corrector knob.

≥You can adjust the brightness of the viewfinder

from the menu.

OPEN

2 90o1 180o

12:30:4512:30:45

1. 4. 2006

12:30:45

1. 4. 2006 1. 4. 2006

12:30:45

1. 4. 2006

VQT0T39_EP_eng.book 12 ページ２００５年１２月２６日　月曜日　午後８時７分

Before using

13

VQT0T39

Quick Start

When quick start is ON the battery power is still

being consumed, even when the LCD monitor

and the viewfinder are closed.

The movie camera will resume recording/pause

mode about 1.7 seconds after the LCD monitor or

the viewfinder is reopended.

≥Please note in quick start mode approximately

half the pause recording power is being

consumed. Using quick start mode will reduce

the battery recording/playback time.

≥This is only activated in the following cases.

≥A tape or a card is inserted, while the Tape

Recording Mode is set.

≥A card is inserted, while the Card Recording

Mode is set.

≥Set to Tape/Card Recording Mode.

1 Set [SETUP] >> [QUICK START] >> [ON].

(

-18-)

2 While the [OFF/ON] switch is still set to

[ON], close the LCD monitor and retract the

viewfinder.

≥The Status indicator lights green and the unit

goes into quick start standby mode.

≥The movie camera will not go into quick start

standby mode unless the LCD monitor is

closed and the viewfinder is retracted.

3 Open the LCD monitor or extend the

Viewfinder.

≥The Status indicator lights red and the

camera is put into recording pause approx.

1.7 seconds after it is turned on.

ª

To cancel Quick Start

1 Set [SETUP] >> [QUICK START] >> [OFF].

(

-18-)

≥If the [OFF/ON] switch is set to [OFF] while the

unit is in quick start standby mode, the power

turns off.

≥If the standby continues for approx. 30 minutes,

then the Status indicator will go off and the

camera will be completely turned off.

≥If the Mode dial is moved or the battery is

removed in quick start standby mode, quick

start is cancelled and the power turns off.

≥When the movie camera is quick-started with

the white balance on automatic, it may take

some time until the white balance is adjusted if

the scene being recorded has a light source

different from the scene last recorded. (When

the colour night view function is used, however,

the white balance of the scene last recorded is

retained.)

≥If the power is turned on in quick start standby

mode, the zoom magnification becomes 1k and

the picture size may differ from what it was

before quick start standby mode.

≥If [POWER SAVE] (

-54-) is set to [5 MINUTES]

and the unit automatically goes into quick start

standby mode, set the [OFF/ON] switch to

[OFF], then to [ON] again. Also, close the LCD

monitor and retract the viewfinder and then

open the LCD monitor or extend the viewfinder

again.

≥When using the AC adaptor, Quick Start can be

used even if a tape/card is not inserted.

OFF

ON

OFF

ON

VQT0T39_EP_eng.book 13 ページ２００５年１２月２６日　月曜日　午後８時７分

Before using

14

VQT0T39

Inserting/removing a cassette

1 Fit the AC adaptor or the battery and turn on

the power.

2 Slide the [OPEN/EJECT] lever and open the

cassette cover.

≥When the cover is fully opened, the cassette

holder will come out.

3 After the cassette holder is opened, insert/

remove the cassette.

≥When inserting a cassette, orient it as shown

in the figure, and then securely insert it as far

as it goes.

≥When removing, pull it straight out.

4 Push the [PUSH] mark 1 in order to close

the cassette holder.

≥The cassette holder is housed.

5 Only after the cassette holder is completely

housed, close the cassette cover tightly.

≥When inserting a previously recorded cassette,

use the blank search function to find the position

where you want to continue recording. If you are

overwriting a previously recorded cassette, be

sure to find the position where you want to

continue recording.

≥When closing the cassette cover, do not get

anything, such as a cable, caught in the cover.

≥After use, be sure to rewind the cassette

completely, remove it and put it in a case. Store

the case in an upright position. (

-65-)

≥If the indicator of the condensation does not

display on the LCD monitor and/or viewfinder

and you notice condensation on the lens or the

main unit, do not open the cassette cover

otherwise condensation may be formed on the

heads or the cassette tape. (

-62-)

ª

When the cassette holder does not

come out

≥Close the cassette cover completely, and then

open it again completely.

≥Check if the battery has run down.

ª

When the cassette holder cannot be

housed

≥Set the [OFF/ON] switch to [OFF], then to [ON]

again.

≥Check if the battery has run down.

ª

Accidental erasure prevention

If the accidental erasure prevention slider 1 of a

cassette is opened (slide in the direction of the

[SAVE] arrow), the cassette cannot be recorded.

When recording, close the accidental erasure

prevention slider of the cassette (slide in the

direction of the [REC] arrow).

OPEN

/

EJEC

T

PUSH

1

R E C

SAVE

1

VQT0T39_EP_eng.book 14 ページ２００５年１２月２６日　月曜日　午後８時７分

Before using

15

VQT0T39

Inserting/removing a card

Before inserting/removing a card, set the

[OFF/ON] switch to [OFF].

≥If the card is inserted or removed with the power

turned on, this camera may malfunction or the

data recorded on the card may be lost.

1 Turn off the power 1.

≥Check that the Status indicator has gone off.

2 Slide the card slot cover outwards to open.

3 Insert/remove the card into/from the card

slot.

≥When inserting a card, face the label side 1

towards you and push it straight in with one

stroke as far as it goes.

≥When removing the card, press the centre of

the card and then pull it straight out.

4 Securely close the card slot cover.

ª

Concerning the card

≥Do not format the card with another movie

camera or any personal computer. This

operation may make the card unusable.

≥Do not touch the terminals on the back of the

card.

≥Electrical noise, static electricity, or failure of the

movie camera or the card may damage or erase

the data stored on the card. We recommend

saving important data on a personal computer

by using a USB cable, PC card adaptor, and

USB reader/writer.

ª

Card access lamp

≥When the camera accesses the card (reading,

recording, playback, erasing, etc.), the access

lamp lights up.

≥If the following operations are performed when

the access lamp is lit, then the card or the

recorded data may be damaged or the camera

may malfunction.

≥Inserting or removing the card.

≥Operating the [OFF/ON] switch or the mode

dial.

≥Attaching and removing the battery.

ª

SD Memory Card

≥The memory capacity indicated on the SD

Memory Card label corresponds to the total

amount of capacity to protect and manage the

copyright and the capacity available as

conventional memory for a movie camera,

personal computer or other equipment.

ª

Concerning the write protection

switch on the SD Memory Card

≥The SD Memory Card has a write protection

switch on it. If the switch is moved to [LOCK],

you cannot write to the card, erase the data on

it, or format it. If it is moved back, you can.

OFF

ON

1

2

1

VQT0T39_EP_eng.book 15 ページ２００５年１２月２６日　月曜日　午後８時７分

Before using

16

VQT0T39

Selecting a mode

Rotate the mode dial to select the desired mode.

1 Rotate the mode dial.

≥Set your desired mode to 1.

: TAPE RECORDING MODE

Use this when you record the image on a tape.

(Also, you can simultaneously record still pictures

on a card while recording images on a tape.)

: TAPE PLAYBACK MODE

Use this to play back a tape.

: CARD RECORDING MODE

Use this to record still pictures on a card.

: CARD PLAYBACK MODE

Use this to play back the still pictures recorded on

a card.

: PC CONNECTION MODE

You can view or edit the images recorded on a

card on your personal computer.

(Refer to the operating instructions for PC

connection.)

How to use the joystick

ª Basic joystick operations

Operations on the menu screen and selection

of files to be played back on the multi-image

display

Move the joystick up, down, left, or right to select

an item or file, and then push in the centre to set

it.

ª

Joystick and screen display

Push the centre of the joystick, and icons will be

displayed on the screen. Each time the joystick is

moved down, the indication changes.

(In the Tape playback mode or the Card Playback

Mode, the icons will be automatically displayed on

the screen.)

1) Tape recording mode

([AUTO/MANUAL/FOCUS] switch is set to

[AUTO])

≥1 is displayed while recording on a tape.

1 Select by moving up.

2 Select by moving down.

3 Select by moving left.

4 Select by moving right.

5 Determine by pushing the centre.

1

PC

1

3

2

4

5

1/4

2 Fade

-31-

3 Backlight compensation -30-

1 Help mode -18-

2/4

2 Soft skin mode

-31-

1 Tele macro -31-

3/4

3 Colour night view/

0 lux colour night view

-30-

4/4

2 Recording check

-26-

1 Blank search -26-

1

VQT0T39_EP_eng.book 16 ページ２００５年１２月２６日　月曜日　午後８時７分

Before using

17

VQT0T39

2) Tape recording mode

([AUTO/MANUAL/FOCUS] switch is set to

[MANUAL])

≥1 is displayed while recording on a tape.

3) Tape playback mode

4) Card recording mode

([AUTO/MANUAL/FOCUS] switch is set to

[AUTO])

5) Card recording mode

([AUTO/MANUAL/FOCUS] switch is set to

[MANUAL])

6) Card Playback Mode

5/5

2 Iris or gain value

-39-

3 White balance -38-

1 Shutter speed -39-

3 Playback/pause

-41-

4 Stop -41-

2 Rewind (review playback) -41-

1 Fast forward (cue playback) -41-

1

1/2

2 Self-timer recording

-35-

3 Backlight compensation -30-

1 Help mode -18-

2/2

2 Soft skin mode

-31-

1 Tele macro -31-

3/3

2 Iris or gain value

-39-

3 White balance -38-

1 Shutter speed -39-

3 Slide show start/pause

-43-

4 Delete -44-

2 Playback previous picture -43-

1 Playback next picture -43-

VQT0T39_EP_eng.book 17 ページ２００５年１２月２６日　月曜日　午後８時７分

Before using

18

VQT0T39

Help mode

Select an icon for an explanation of the function.

≥Set to Tape/Card Recording Mode.

1 Press the joystick to display the icon during

the recording pause. Move the joystick

down until icon 1 appears.

2 Move the joystick right to select the Help

mode icon [ ].

≥The help mode explains the operation icons

displayed when the [AUTO/MANUAL/

FOCUS] switch is set to [AUTO] in Tape/Card

Recording Mode.

3 Move the joystick up, left, or right to select

the desired icon.

≥An explanation of the selected icon is

displayed on the screen.

≥Each time the joystick is moved down, the

indication changes.

ª

To exit the Help mode

Select [EXIT] icon or press the [MENU] button.

≥When the Help mode is used, functions cannot

be set.

Switching the language

You can switch the language on the screen

display or the menu screen.

1 Set [LANGUAGE] >> select the desired

language.

Using the menu screen

For each individual menu, please refer to -52-.

1 Press the [MENU] button.

≥The menu corresponding to the mode

selected by the mode dial is displayed.

≥Do not switch the mode dial when the menu is

displayed.

2 Move the joystick up or down in order to

select the top menu.

3 Move the joystick right or press it to set the

selection.

4 Move the joystick up or down in order to

select the sub-menu.

1

MENU

VQT0T39_EP_eng.book 18 ページ２００５年１２月２６日　月曜日　午後８時７分

Before using

19

VQT0T39

5 Move the joystick right or press it to set the

selection.

6 Move the joystick up or down in order to

select the item to be set.

7 Press the joystick to determine the setting.

ª

To exit the menu screen

Press the [MENU] button.

ª

To get back to the previous screen

Move the joystick left.

ª

About the menu setting

≥The menu is not displayed while recording on a

tape or a card. Also, you cannot record on a

tape or a card while the menu is displayed.

ª

Operating with remote control

The menu screen transition is the same as when

the buttons on the main unit are used.

1 Press the [MENU] button.

2 Select a menu item.

≥Use the direction buttons (3, 2, 1, 4) and

[ENTER] button in place of the joystick on the

main unit.

3 Press the [MENU] button to exit the menu

screen.

VQT0T39_EP_eng.book 19 ページ２００５年１２月２６日　月曜日　午後８時７分

Before using

20

VQT0T39

Adjusting LCD monitor/viewfinder

ª Adjusting the brightness and colour

level

1

Set [SETUP] >> [LCD SET] or [EVF SET] >>

[YES].

2 Move the joystick up or down in order to

select the item to be adjusted.

[LCD SET]

:Brightness of the LCD monitor

:Colour level of the LCD monitor

[EVF SET]

:Brightness of the viewfinder

3 Move the joystick left or right to move the

bar indication representing the brightness.

4 Press the [MENU] button or the joystick to

complete the settings.

≥When the LCD monitor is rotated by 180°

towards the lens, the brightness of the LCD

monitor cannot be adjusted.

≥To adjust the brightness of the viewfinder, close

the LCD monitor and extend the viewfinder to

activate it.

≥These settings will not affect the images actually

recorded.

ª

In order to increase the brightness of

the entire LCD monitor

1

Press the [POWER LCD] button.

≥The [ ] indication appears on the LCD

monitor.

≥If the [POWER LCD] button is pressed, the

entire LCD monitor will become approx. twice

as bright as the normal.

≥When the [POWER LCD] button is pressed

again, the [ ] indication disappears and the

original brightness is restored.

≥This will not affect the images to be recorded.

≥If you turn on the camera when the AC adaptor

is used, the [POWER LCD] function will

automatically be activated.

≥You cannot use this function in PC Connection

Mode.

ª

Changing the picture quality on the

LCD monitor

1

Set [SETUP] >> [LCD AI] >> [DYNAMIC] or

[NORMAL].

[DYNAMIC]: The image on the LCD monitor

becomes clear and vivid. Optimum

contrast and brightness are set

depending on the scenes recorded.

Clear and brilliant images are

presented.

[NORMAL]: Switches to the standard picture

quality.

≥The effect will vary depending on the scene

recorded.

≥The picture quality on the viewfinder will not be

affected.

≥This function is automatically set to [DYNAMIC]

when the brightness of the LCD monitor is

increased (the [ ] indication appears on the

LCD monitor) and cannot be set to [NORMAL]

independently.

≥This will not affect the images to be recorded.

≥When the LCD monitor is rotated by 180°

towards the lens, the picture quality of the LCD

monitor is temporarily adjusted as if the

[LCD AI] is set to [NORMAL].

EVF

POWER

LCD

VQT0T39_EP_eng.book 20 ページ２００５年１２月２６日　月曜日　午後８時７分

Strona jest ładowana ...

Panasonic NVGS500 Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Panasonic NVGS500 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty