Panasonic NVGS60EP Instrukcja obsługi

Operating Instructions

Instrukcja obsługi

Návod k použití

Kezelési utasítás

Digital Video Camera

Model No. NV-GS60EP

Before use, please read these instructions completely.

Przed pierwszym włączeniem kamery prosimy o dokładne przeczytanie

instrukcji obsługi.

Před použitím si, prosíme, přečtěte celý návod.

Használat előtt kérjük, hogy teljesen olvassa el ezt a kezelési utasítást.

LSQT1171 A

LSQT1171ENG.book 1 ページ２００７年１月１０日　水曜日　午後１時７分

2

LSQT1171

Information for your safety

ª Carefully read the Operating

Instructions and use the Movie

Camera correctly.

≥Injury or material damage resulting from any

kind of use that is not in accordance with the

operating procedures explained in these

Operating Instructions are the sole

responsibility of the user.

Try out the Movie Camera.

Be sure to try out the Movie Camera before

recording your first important event and check

that it records properly and functions correctly.

The manufacturer is not liable for loss of

recorded contents.

The manufacturer shall in no event be liable for

the loss of recordings due to malfunction or defect

of this Movie Camera, its accessories or

cassettes.

Carefully observe copyright laws.

Recording of pre-recorded tapes or discs or other

published or broadcast material for purposes

other than your own private use may infringe

copyright laws. Even for the purpose of private

use, recording of certain material may be

restricted.

≥The Movie Camera uses copyright-protected

technologies and is protected by the patented

technologies and intellectual properties of

Japan and the U.S. To use these copyright-

protected technologies, authorization of the

Macrovision Company is required. It is

prohibited to disassemble or modify the Movie

Camera.

≥All other company and product names in the

operating instructions are trademarks of their

respective corporations.

Pages for reference

Pages for reference are indicated by dashes

either side of a number, for example:

-00-

The menu operation flow is indicated by >> in the

description.

WARNING:

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PRODUCT DAMAGE,

≥ DO NOT EXPOSE THIS APPARATUS TO RAIN,

MOISTURE, DRIPPING OR SPLASHING AND

THAT NO OBJECTS FILLED WITH LIQUIDS,

SUCH AS VASES, SHALL BE PLACED ON THE

APPARATUS.

≥ USE ONLY THE RECOMMENDED

ACCESSORIES.

≥ DO NOT REMOVE THE COVER (OR BACK);

THERE ARE NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CAUTION!

≥ DO NOT INSTALL OR PLACE THIS UNIT IN A

BOOKCASE, BUILT-IN CABINET OR IN

ANOTHER CONFINED SPACE. ENSURE THE

UNIT IS WELL VENTILATED. TO PREVENT RISK

OF ELECTRIC SHOCK OR FIRE HAZARD DUE

TO OVERHEATING, ENSURE THAT CURTAINS

AND ANY OTHER MATERIALS DO NOT

OBSTRUCT THE VENTILATION VENTS.

≥ DO NOT OBSTRUCT THE UNIT’S VENTILATION

OPENINGS WITH NEWSPAPERS,

TABLECLOTHS, CURTAINS, AND SIMILAR

ITEMS.

≥ DO NOT PLACE SOURCES OF NAKED FLAMES,

SUCH AS LIGHTED CANDLES, ON THE UNIT.

≥ DISPOSE OF BATTERIES IN AN

ENVIRONMENTALLY FRIENDLY MANNER.

The socket outlet shall be installed near the

equipment and easily accessible.

The mains plug of the power supply cord shall

remain readily operable.

To completely disconnect this apparatus from

the AC Mains, disconnect the power supply

cord plug from AC receptacle.

Product Identification Marking is located on the

bottom of units.

LSQT1171ENG.book 2 ページ２００７年１月１０日　水曜日　午後１時７分

3

LSQT1171

ª EMC Electric and magnetic

compatibility

This symbol (CE) is located on the rating

plate.

Use only the recommended accessories.

≥Do not use any other AV cables except the

supplied one.

≥When you use the cable which are sold

separately, please make sure to use the one

whose length is less than 3 metres.

Information on Disposal for Users of

Waste Electrical & Electronic Equipment

(private households)

This symbol on the

products and/or

accompanying

documents means

that used electrical

and electronic

products should not

be mixed with

general household

waste.

For proper

treatment, recovery

and recycling, please take these products to

designated collection points, where they will

be accepted on a free of charge basis.

Alternatively, in some countries you may be

able to return your products to your local

retailer upon the purchase of an equivalent

new product.

Disposing of this product correctly will help to

save valuable resources and prevent any

potential negative effects on human health

and the environment which could otherwise

arise from inappropriate waste handling.

Please contact your local authority for further

details of your nearest designated collection

point.

Penalties may be applicable for incorrect

disposal of this waste, in accordance with

national legislation.

For business users in the European

Union

If you wish to discard electrical and

electronic equipment, please contact your

dealer or supplier for further information.

Information on Disposal in other

Countries outside the European Union

This symbol is only valid in the European

Union.

If you wish to discard this product, please

contact your local authorities or dealer and

ask for the correct method of disposal.

ENGLISH

LSQT1171ENG.book 3 ページ２００７年１月１０日　水曜日　午後１時７分

4

LSQT1171

Contents

Information for your safety ............................... 2

Before using

Accessories ..................................................... 5

Optional ........................................................... 5

Parts identification and handling...................... 5

Fitting the lens cap .......................................... 7

The grip belt..................................................... 7

Power supply ................................................... 8

Charging time and recordable time.................. 9

Turning the camera on..................................... 9

Setting date and time..................................... 10

Using the LCD monitor .................................. 11

Using the viewfinder ...................................... 11

Quick start...................................................... 12

Inserting/removing a cassette........................ 13

Selecting a mode........................................... 14

How to use the joystick.................................. 14

Help mode ..................................................... 15

Switching the language.................................. 16

Using the menu screen.................................. 16

Adjusting LCD monitor/viewfinder.................. 17

Record mode

Check before recording ................................. 18

Recording on a tape ...................................... 19

Recording check............................................ 19

Blank search function .................................... 20

Recording a still picture on a tape

(Photoshot).................................................. 20

Zoom in/out function ...................................... 21

Recording yourself......................................... 22

Backlight compensation function ................... 22

Colour Night view function ............................. 23

Soft skin mode............................................... 23

Fade in/fade out function ............................... 24

Wind noise reduction function........................ 24

Recording images for wide-screen TVs......... 25

Image stabilizer function................................ 25

Recording in various situations

(Scene mode).............................................. 26

Recording in natural colours

(White balance)........................................... 27

Manual focus adjustment............................... 28

Manual shutter speed/

aperture adjustment .................................... 28

Playback mode

Playing back tape.......................................... 30

Frame-by-frame playback ............................. 31

Playback on TV ............................................. 31

Edit mode

Copying onto a DVD recorder or a VCR

(Dubbing) .................................................... 32

Using the DV Cable for Recording

(Digital Dubbing) ......................................... 32

Using the movie camera as a Web Camera

(Windows XP SP2) ..................................... 33

Using on Macintosh....................................... 34

Menu

Menu list........................................................ 35

Menus related to taking pictures ................... 36

Menus related to playback ............................ 37

Other menus.................................................. 37

Others

Indications ..................................................... 38

Warning/alarm indications ............................. 39

Functions cannot be used

simultaneously ............................................ 40

Before requesting repair

(Problems and solutions) ............................ 40

Cautions for Use............................................ 43

Explanation of terms...................................... 46

Specifications

Specifications ................................................ 48

LSQT1171ENG.book 4 ページ２００７年１月１０日　水曜日　午後１時７分

Before using

5

LSQT1171

Before using

Accessories

The followings are the accessories supplied with

this product.

1) AC adaptor, DC input lead, AC mains lead

-8-

2) Battery pack -8-

3) AV cable -32-

Optional

1) AC adaptor (VW-AD11E)

2) Battery pack (lithium/CGR-DU06/640 mAh)

3) Battery pack (lithium/CGA-DU07/680 mAh)

4) Battery pack (lithium/CGA-DU12/1150 mAh)

5) Battery pack (lithium/CGA-DU14/1360 mAh)

6) Battery pack (lithium/CGA-DU21/2040 mAh)

7) Wide conversion lens (VW-LW3007E)

8) Tele conversion lens (VW-LT3014E)

9) ND filter (VW-LND30E)

10) MC protector (VW-LMC30E)

11) Tripod (VW-CT45E)

12) DV cable (VW-CD1E)

≥Some optional accessories may not be

available in some countries.

Parts identification and handling

ª Camera

(1) White balance sensor -27-

(2)

Grip belt -7-

(3)

Lens

≥Fit the MC protector (VW-LMC30E;

optional), the ND filter (VW-LND30E;

optional), the tele conversion lens

(VW-LT3014E; optional) or the wide

conversion lens (VW-LW3007E; optional) in

front of the lens. Do not fit the other

accessories. (except for the lens cap)

(4) Microphone (built-in, stereo) -21-, -24-

(5)

Audio-video output terminal [A/V] -32-

≥Use the supplied AV cable only, otherwise

audio may not be played back normally.

(6) Speaker -30-

(7)

Cassette eject lever [OPEN/EJECT] -13-

(8)

Cassette holder -13-

(9)

DV terminal [DV] -32-

(10)

USB terminal [ ]

1)

2)

3)

K2GJ2DC00015

K2KC4CB00022CGR-DU06

VSK0651B

(DE-974GC)

K2CR2DA00004

(1)

(3)

(4)

(5)

(2)

DV

(6) (7)

(8)

(9) (10)

LSQT1171ENG.book 5 ページ２００７年１月１０日　水曜日　午後１時７分

Before using

6

LSQT1171

(11) Viewfinder -11-, -46-

(12)

Battery holder -8-

(13)

Battery release lever

[BATTERY RELEASE]

-8-

(14)

DC input terminal [DC/C.C.IN] -8-

(15)

Power switch [OFF/ON] -9-

(16)

Status indicator -9-

(17)

Menu button [MENU] -16-

(18)

Joystick -14-

(19)

Mode dial -14-

(20)

Recording start/stop button -19-

(21)

LCD monitor -11-, -46-

(22)

LCD monitor open part [OPEN] -11-

(23)

Reset button [RESET] -39-, -42-

(24)

Mode select switch

[AUTO/MANUAL/FOCUS]

-18-, -26-, -28-

(25)

Cassette cover -13-

(26)

Zoom lever [W/T] -21-

Volume lever [sVOLUMEr] -30-

(27)

Photoshot button [ ] -20-

(28)

Tripod receptacle

This is a hole for attaching the camera to optional

tripod/VW-CT45E. (Please carefully read the

operating instructions for how to attach the tripod

to the camera.)

(29) Shoulder strap fixture

≥Put the strap (optional) through the fixture 1

and through the stopper 2 so it will not come

off. Extend part 3 by at least 2 cm.

≥Fit the other end of the belt similarly.

Due to limitations in LCD production

technology, there may be some tiny bright or

dark spots on the Viewfinder screen.

However, this is not a malfunction and does

not affect the recorded picture.

Due to limitations in LCD production

technology, there may be some tiny bright or

dark spots on the LCD monitor screen.

However, this is not a malfunction and does

not affect the recorded picture.

(11)

(12)

(13)

(15)

(16)

(17)

(18)

(19)

(20)

(14)

(21)

(22)

(23)

(24)

(25)

(26)

(27)

(28)

(29)

3

2

1

LSQT1171ENG.book 6 ページ２００７年１月１０日　水曜日　午後１時７分

Before using

7

LSQT1171

Fitting the lens cap

Fit the lens cap to protect the surface of the lens.

1 The lens cap and lens cap cord comes

preattached to the grip belt.

Pass the end of the lens cap cord through

the attached eye on the lens cap. Then pass

the lens cap through the loop made by itself

and pull tight.

≥When not using the lens cap, pull the lens cap

cord in the direction of the arrow. 1

≥When you are not recording, be sure to cover

the lens with the lens cap for protection.

2

≥When you remove the lens cap, press the knobs

firmly.

The grip belt

Adjust the belt length so it fits your hand.

1 Adjust the belt length.

1 Flip the belt.

2 Adjust the length.

3 Fix the belt.

2

1

3

2

1

LSQT1171ENG.book 7 ページ２００７年１月１０日　水曜日　午後１時７分

Before using

8

LSQT1171

Power supply

ª Charging the battery

When this product is purchased, the battery is not

charged. Charge the battery before using this

product.

≥Battery charging time (

-9-)

≥We recommend using Panasonic batteries. (

-5-)

≥If you use other batteries, we cannot guarantee

the quality of this product.

≥If the DC input lead is connected to the AC

adaptor, then the battery will not get charged.

Remove the DC input lead from the AC adaptor.

1 Connect the AC mains lead to the AC

adaptor and the AC mains socket.

2 Put the battery on the battery mount by

aligning the mark, and then securely plug it

in.

ª

Charging lamp

Lights up: Charging

Goes off: Charging completed

Flashing: The battery is over discharged

(discharged excessively). In a while,

the lamp will light up and normal

charging will start.

When the battery temperature is

excessively high or low, the

[CHARGE] lamp flashes and the

charging time will be longer than

normal.

ª

Connecting to the AC outlet

The unit is in the standby condition when the AC

adaptor is connected. The primary circuit is

always “live” as long as the AC adaptor is

connected to an electrical outlet.

1 Connect the AC mains lead to the AC

adaptor and the AC mains socket.

2 Connect the DC input lead to the AC

adaptor.

3 Connect the DC input lead to this product.

≥The output plug of the AC mains lead is not

completely connected to the AC adaptor

socket. As shown in 1, there is a gap.

≥Do not use the power cord for other

equipment since the power cord is exclusively

designed for the movie camera. Or do not use

the power cord of other equipment for the

movie camera.

ª

Fitting the battery

Push the battery against the battery holder and

slide it until it clicks.

ª

Removing the battery

While sliding the [BATTERY RELEASE] lever,

slide the battery to remove it.

≥Hold the battery with your hand so it does not

fall.

≥Before removing the battery, be sure to set the

[OFF/ON] switch to [OFF].

1

CAUTION

Danger of explosion if battery is

incorrectly replaced. Replace only with

the same or equivalent type

recommended by the manufacturer.

Dispose of used batteries according to

the manufacturer’s instructions.

BATTERY

RELEASE

LSQT1171ENG.book 8 ページ２００７年１月１０日　水曜日　午後１時７分

Before using

9

LSQT1171

Charging time and recordable time

The times shown in the table below show the

times at a temperature of 25 oC and a humidity of

60%. This is just a guide. If the temperature is

higher or lower than the specified value, the

charging time will become longer.

A Charging time

B Maximum continuously recordable time

C Intermittent recordable time

(The intermittent recordable time refers to

recordable time when the recording and stopping

operations are repeated.)

“1 h 40 min” indicates 1 hour 40 minutes.

≥The battery CGR-DU06 is supplied.

≥The times shown in the table are rough

estimates. The times indicate the recordable

times when the viewfinder is used. The times in

parentheses indicate the recordable times when

the LCD monitor is used.

≥We recommend the Battery Pack CGA-DU12,

CGA-DU14 and CGA-DU21 for long time

recording (2 hours or more for continuous

recording, 1 hour or more for intermittent

recording).

≥The recordable time will become shorter in the

following cases:

≥When you use both the viewfinder and the

LCD monitor simultaneously while rotating

the LCD monitor frontward to record yourself

etc.

≥The batteries heat up after use or charging. The

main unit of the movie camera being used will

also heat up. This is normal.

≥Along with the reduction of the battery capacity,

the display will change: # #

# # . If the battery

discharges, then ( ) will flash.

Turning the camera on

When the camera is turned on with the lens cap

fitted, the automatic white balance adjustment

may not function properly. Please turn the camera

on after removing the lens cap.

ª

How to turn on the power

1 While pressing the button 1, set the

[OFF/ON] switch to [ON].

≥The status indicator lights red and the power

turns on.

≥If the LCD monitor is closed and the

viewfinder is retracted while the [OFF/ON]

switch is set to [ON] in the Tape Recording

Mode, the power turn off.

ª

How to turn off the power

1

While pressing the button 1, set the

[OFF/ON] switch to [OFF].

≥Set the [OFF/ON] switch to [OFF] when not

using the camera.

≥The status indicator goes off when the power

turns off.

Supplied

battery/

CGR-DU06

(7.2 V/

640 mAh)

A 1 h 40 min

B 1 h 50 min

(1 h 25 min)

C 55 min

(45 min)

CGA-DU12

(7.2 V/

1150 mAh)

A 2 h 25 min

B 3 h 15 min

(2 h 40 min)

C 1 h 40 min

(1 h 20 min)

CGA-DU14

(7.2 V/

1360 mAh)

A 2 h 45 min

B 3 h 50 min

(3 h)

C 1 h 55 min

(1 h 30 min)

CGA-DU21

(7.2 V/

2040 mAh)

A 3 h 55 min

B 5 h 45 min

(4 h 30 min)

C 2 h 55 min

(2 h 15 min)

CGA-DU07

(7.2 V/

680 mAh)

A 1 h 30 min

B 1 h 55 min

(1 h 30 min)

C 1 h

(45 min)

OFF

ON

1

OFF

ON

1

LSQT1171ENG.book 9 ページ２００７年１月１０日　水曜日　午後１時７分

Before using

10

LSQT1171

ª How to turn the power on and off with

the LCD monitor/viewfinder

When the power switch is set to [ON], the power

can be turned on and off with the LCD monitor

and the viewfinder when the unit is in Tape

Recording Mode.

1 Open the LCD monitor out or extend the

viewfinder to use. (

-11-)

≥The LCD monitor or the viewfinder will be

activated.

2 Close the LCD monitor and retract the

viewfinder.

≥The power will not turn off unless the LCD

monitor is closed and the viewfinder is

retracted.

≥The status indicator automatically goes off

and the power turns off. (If quick start is set to

[ON] (

-12-), the unit goes into quick start

standby mode and the status indicator lights

green.)

≥The power does not turn off even if the LCD

monitor is closed and the viewfinder is

retracted while recording on a tape.

3 Open the LCD monitor or extend the

viewfinder to turn the power on and use the

movie camera again.

≥The status indicator lights up and the power

turns on.

Setting date and time

When the movie camera is turned on for the first

time, [SET DATE AND TIME] will appear.

≥Select [YES] and press the centre of the

joystick. Do steps 2 and 3 below to set the date/

time.

If the screen shows the incorrect date/time, then

adjust it.

≥Set to Tape Recording Mode.

1 Set [BASIC] >> [CLOCK SET] >> [YES]. (-16-)

2 Move the joystick left or right in order to

select the item to be set. Then move the

joystick up or down to set the desired value.

≥The year will change as follows:

2000, 2001, ..., 2089, 2000, ...

≥The 24-hour clock is used.

3 Press the joystick to determine the setting.

≥The clock function starts at [00] seconds.

ª

About date/time

≥The date and time function are driven by a

built-in lithium battery.

≥Make sure to check the time before recording

because the built-in clock is not very accurate.

ª

Recharging the built-in lithium battery

≥If [0] or [--] is appears when the camera is

turned on, then the built-in lithium battery has

run down. Use the steps below to charge the

battery. When turn on the power for the first time

after charging, [SET DATE AND TIME] will

appear. Select [YES] and set the date and time.

Connect the AC adaptor to the camera or attach

the battery to the camera, and the built-in lithium

battery will be recharged. Leave the camera as

is for approx. 24 hours, and the battery will drive

the date and time for approx. 6 months. (Even if

the [OFF/ON] switch is set to [OFF], the battery

is still being recharged.)

OFF

ON

OFF

ON

OFF

ON

LSQT1171ENG.book 10 ページ２００７年１月１０日　水曜日　午後１時７分

Before using

11

LSQT1171

Using the LCD monitor

You can record the image while viewing it on the

opened LCD monitor.

1 Put a finger on the LCD monitor open part

and open the LCD monitor out in the

direction of the arrow.

≥It can open up to 90o.

2 Adjust the angle of the LCD monitor as you

prefer.

≥It can rotate up to 180o 1 towards the lens or

90o 2 towards the viewfinder.

≥The brightness and colour level of the LCD

monitor can be adjusted from the menu.

≥If it is forcibly opened or rotated, the camera

may be damaged or fail.

≥If the LCD monitor is rotated by 180o towards

the lens and the viewfinder is extended (when

recording yourself), the LCD monitor and the

viewfinder simultaneously light.

Using the viewfinder

ª Extending the viewfinder

1 Pull out the viewfinder. Extend it by

pinching the extension knob.

≥The viewfinder will be activated. (If the LCD

monitor is opened, the viewfinder will be

deactivated.)

ª

Adjusting the field of view

1 Adjust the focus by sliding the eyepiece

corrector knob.

≥You can adjust the brightness of the viewfinder

from the menu.

1180o 2 90o

12:30:4512:30:4512:30:45

1.4. 20071.4. 20071.4. 2007

12:30:45

1.4. 2007

LSQT1171ENG.book 11 ページ２００７年１月１０日　水曜日　午後１時７分

Before using

12

LSQT1171

Quick start

When quick start is on the battery power is still

being consumed, even when the LCD monitor

and the viewfinder are closed.

The camera will resume recording/pause mode

about 1.7 seconds after the LCD monitor or the

viewfinder is reopened.

≥Please note in quick start mode approximately

half the pause recording power is being

consumed. Using quick start mode will reduce

the battery recording/playback time.

≥This is only activated in the following cases.

≥While using the battery

A tape is inserted, while the Tape Recording

Mode is set.

≥While using the AC adaptor

Quick Start can be used even if a tape is not

inserted.

≥Set to Tape Recording Mode.

1 Set [SETUP] >> [QUICK START] >> [ON].

(

-16-)

2 While the [OFF/ON] switch is still set to

[ON], close the LCD monitor and retract the

viewfinder.

≥The status indicator lights green and the unit

goes into quick start standby mode.

≥The movie camera will not go into quick start

standby unless the LCD monitor is closed and

the viewfinder is retracted.

3 Open the LCD monitor or extend the

viewfinder.

≥The status indicator lights red and the camera

is put into recording pause approx.

1.7 seconds after it is turned on.

ª

To cancel Quick Start

1 Set [SETUP] >> [QUICK START] >> [OFF].

(

-16-)

≥If the [OFF/ON] switch is set to [OFF] while the

unit is in quick start standby, the power turns off.

≥If the standby continues for approx. 30 minutes,

then the status indicator will go off and the

camera will be completely turned off.

≥In the following cases, quick start is canceled

and the power turns off.

≥When the Mode dial is moved.

≥When the battery or AC adaptor is removed.

≥When the tape is removed while using the

battery in Tape Recording Mode.

≥When the camera is quick-started with the white

balance on automatic, it may take some time

until the white balance is adjusted if the scene

being recorded has a light source different from

the scene last recorded. (When the colour night

view function is used, however, the white

balance of the scene last recorded is retained.)

≥If the power is turned on in quick start standby,

the zoom magnification becomes 5k and the

picture size may differ from what it was before

quick start standby.

≥If [POWER SAVE] (

-36-) is set to [5 MINUTES]

and the unit automatically goes into quick start

standby mode, set the [OFF/ON] switch to

[OFF], then to [ON] again. Also, close the LCD

monitor and retract the viewfinder and then

open the LCD monitor or extend the viewfinder

again.

OFF

ON

OFF

ON

OFF

ON

LSQT1171ENG.book 12 ページ２００７年１月１０日　水曜日　午後１時７分

Before using

13

LSQT1171

Inserting/removing a cassette

1 Fit the AC adaptor or the battery and turn on

the power.

2 Slide the [OPEN/EJECT] lever and open the

cassette cover.

≥When the cover is fully opened, the cassette

holder will come out.

3 After the cassette holder is opened, insert/

remove the cassette.

≥When inserting a cassette, orient it as shown

in the figure, and then securely insert it as far

as it goes.

≥When removing, pull it straight out.

4 Push the [PUSH] mark 1 in order to close

the cassette holder.

≥The cassette holder is housed.

5 Only after the cassette holder is completely

housed, close the cassette cover by

pressing the mark 2.

≥When inserting a previously recorded cassette,

use the blank search function to find the position

where you want to continue recording. If you are

overwriting a previously recorded cassette, be

sure to find the position where you want to

continue recording.

≥Close the cassette cover tightly.

≥When closing the cassette cover, do not get

anything, such as a cable, caught in the cover.

≥After use, be sure to rewind the cassette

completely, remove it and put it in a case. Store

the case in an upright position. (

-45-)

≥If the indicator of the condensation does not

display on the LCD monitor and/or the

viewfinder and you notice condensation on the

lens or the main unit, do not open the cassette

cover otherwise condensation may be formed

on the heads or the cassette tape. (

-43-)

ª

When the cassette holder does not

come out

≥Close the cassette cover completely, and then

open it again completely.

≥Check if the battery has run down.

≥Check if the cassette compartment cover is in

contact with grip belt as shown below. If so, be

sure the grip belt stays clear of the cover when

opening.

ª

When the cassette holder cannot be

housed

≥Set the [OFF/ON] switch to [OFF], then to [ON]

again.

≥Check if the battery has run down.

ª

Accidental erasure prevention

If the accidental erasure prevention slider 1 of a

cassette is opened (slide in the direction of the

[SAVE] arrow), the cassette cannot be recorded.

When recording, close the accidental erasure

prevention slider of the cassette (slide in the

direction of the [REC] arrow).

Caution:

Take care not to trap your fingers under the

cassette holder when closing it.

OPEN/

EJECT

1

PUSH

2

R E C

SAVE

1

LSQT1171ENG.book 13 ページ２００７年１月１０日　水曜日　午後１時７分

Before using

14

LSQT1171

Selecting a mode

Rotate the mode dial to select the desired mode.

1 Rotate the mode dial.

≥Set your desired mode to 1.

: TAPE RECORDING MODE

Use this when you record the image on a tape.

: TAPE PLAYBACK MODE

Use this to play back a tape.

How to use the joystick

ª Basic joystick operations

Operations on the menu screen and selection

of files to be played back on the multi-image

display

Move the joystick up, down, left or right to select

an item or file, and then push in the centre to set

it.

ª

Joystick and screen display

Push the centre of the joystick, and icons will be

displayed on the screen. Each time the joystick is

moved down, the indication changes.

(In the Tape Playback Mode, the icons will be

automatically displayed on the screen.)

1) Tape Recording Mode

([AUTO/MANUAL/FOCUS] switch is set to

[AUTO])

≥1 is displayed while recording on a tape.

1 Select by moving up.

2 Select by moving down.

3 Select by moving left.

4 Select by moving right.

5 Determine by pushing the centre.

1

3

2

4

5

1/4

2 Fade

-24-

3 Backlight compensation -22-

1 Help mode -15-

2/4 2 Soft skin mode -23-

3/4 3 Colour night view -23-

4/4

2 Recording check

-19-

1 Blank search -20-

1

LSQT1171ENG.book 14 ページ２００７年１月１０日　水曜日　午後１時７分

Before using

15

LSQT1171

2) Tape Recording Mode

([AUTO/MANUAL/FOCUS] switch is set to

[MANUAL])

≥1 is displayed while recording on a tape.

≥2 is displayed only when the [AUTO/

MANUAL/FOCUS] switch is set to [FOCUS].

3) Tape Playback Mode

Help mode

Select an icon for an explanation of the function.

≥Set to Tape Recording Mode.

1 Press the joystick to display the icon during

the recording pause. Move the joystick

down until icon 1 appears.

2 Move the joystick right to select the Help

mode icon [ ].

≥The help mode explains the operation icons

displayed when the [AUTO/MANUAL/

FOCUS] switch is set to [AUTO] in Tape

Recording Mode.

3 Move the joystick up, left, or right to select

the desired icon.

≥An explanation of the selected icon is

displayed on the screen.

≥Each time the joystick is moved down, the

indication changes.

ª

To exit the Help mode

Select [EXIT] or press the [MENU] button.

≥When the Help mode is used, it is not possible

to record or set the functions.

5/5

2 Iris or gain value

-28-

3 White balance -27-

1 Shutter speed -28-

6/6

2

Manual focus adjustment -28-

1

3 Playback/pause

-30-

4 Stop -30-

2 Rewind (review playback) -30-

1 Fast forward (cue playback) -30-

1

2

1

LSQT1171ENG.book 15 ページ２００７年１月１０日　水曜日　午後１時７分

Before using

16

LSQT1171

Switching the language

You can switch the language on the screen

display or the menu screen.

1 Set [LANGUAGE] >> select the desired

language.

Using the menu screen

For each individual menu, please refer to -35-.

1 Press the [MENU] button.

≥The menu corresponding to the mode

selected by the mode dial is displayed.

≥Do not switch the mode dial when the menu is

displayed.

2 Move the joystick up or down in order to

select the top menu.

3 Move the joystick right or press it to set the

selection.

4 Move the joystick up or down in order to

select the sub-menu.

5 Move the joystick right or press it to set the

selection.

6 Move the joystick up or down in order to

select the item to be set.

7 Press the joystick to determine the setting.

ª

To exit the menu screen

Press the [MENU] button.

ª

To get back to the previous screen

Move the joystick left.

ª

About the menu setting

≥The menu is not displayed while recording on a

tape. Also, you cannot record on a tape while

the menu is displayed.

MENU

LSQT1171ENG.book 16 ページ２００７年１月１０日　水曜日　午後１時７分

Before using

17

LSQT1171

Adjusting LCD monitor/viewfinder

ª Adjusting the brightness and colour

level

1

Set [SETUP] >> [LCD SET] or [EVF SET] >>

[YES].

2 Move the joystick up or down in order to

select the item to be adjusted.

[LCD SET]

: Brightness of the LCD monitor

: Colour level of the LCD monitor

[EVF SET]

: Brightness of the viewfinder

3 Move the joystick left or right to move the

bar indication representing the brightness.

4 Press the [MENU] button or the joystick to

complete the settings.

≥When the LCD monitor is rotated by 180°

towards the lens, the brightness of the LCD

monitor cannot be adjusted.

≥To adjust the brightness of the viewfinder, close

the LCD monitor and extend the viewfinder to

activate it.

≥These settings will not affect the images actually

recorded.

≥If you adjust the colour level of the LCD monitor,

the colour level of the viewfinder also

automatically changes.

EVF

LSQT1171ENG.book 17 ページ２００７年１月１０日　水曜日　午後１時７分

Record mode

18

LSQT1171

Record mode

Check before recording

Check the following before recording important

events such as weddings or when the movie

camera has not been used for a long time.

Conduct a test recording to make sure that the

image recording and the audio recording work

properly.

ª

Basic camera holding

1) Hold the camera with both hands.

2) Run your hand through the grip belt.

3) Do not cover the microphones or sensors with

your hands.

4) Keep your arms near your body.

5) Slightly open your legs.

≥When you are in the open air, record pictures

with the sunlight as far in the background as

possible. If the subject is backlit, it will become

dark in the recording.

ª

Check points

≥Remove the lens cap. (-7-)

(When the camera is turned on with the lens cap

fitted, the automatic white balance adjustment

may not function properly. Please turn the

camera on after removing the lens cap.)

≥Grip belt adjustment (

-7-)

≥Open the LCD monitor or extend the viewfinder

(Recording cannot start while the LCD monitor

and the viewfinder are closed. Even if the LCD

monitor and the viewfinder are closed during

recording, the power will not turn off until

recording stops.)

≥Adjustment of LCD monitor/viewfinder (

-17-)

≥Power supply (

-8-)

≥Insert a cassette (

-13-)

≥Setting date/time (

-10-)

≥Setting SP/LP mode (

-18-)

ª

About auto mode

≥Set the [AUTO/MANUAL/FOCUS] switch to

[AUTO], and colour balance (white balance) and

focusing will be adjusted automatically.

≥Auto white balance:

-46-

≥Auto focusing: -47-

≥Depending on the brightness of the subject etc.,

the aperature and shutter speed are

automatically adjusted for an optimum

brightness. (When set to the Tape recording

mode: The shutter speed is adjusted to a

maximum of 1/250.)

≥Colour balance and focus may not be adjusted

depending on light sources or scenes. If so,

manually adjust the white balance and focus.

≥Scene mode setting (

-26-)

≥White balance setting (

-27-)

≥Shutter speed setting (

-28-)

≥Iris/gain value setting (

-28-)

≥Focus setting (

-28-)

ª

Recording mode

You can switch the tape recording mode.

≥Set to Tape Recording Mode.

1 Set [BASIC] >> [REC SPEED] >> [SP] or

[LP].

If the LP mode is selected, the recording time will

be 1.5 times the SP mode, but some functions will

be disabled.

≥We recommend using the SP mode for

important recording.

≥In order to fully exhibit the performances of the

LP mode, we recommend using Panasonic

cassettes marked LP mode.

≥In the LP mode, the picture quality will not be

degraded in comparison with the SP mode, but

mosaic noise may appear on the playback

image or some functions may be disabled.

≥Playback on other digital video equipment

or on digital video equipment without the LP

mode.

≥Playback of the image on other digital video

equipment recorded in the LP mode.

≥Frame-by-frame playback.

4)

5)

1)

2)

3)

AUTO

MANUAL

FOCUS

LSQT1171ENG.book 18 ページ２００７年１月１０日　水曜日　午後１時７分

Record mode

19

LSQT1171

Recording on a tape

Remove the lens cap. (-7-)

(When the camera is turned on with the lens cap

fitted, the automatic white balance adjustment

may not function properly. Please turn the camera

on after removing the lens cap.)

≥Set to Tape Recording Mode.

1 Press the recording start/stop button to

start recording.

2 Press the recording start/stop button again

to pause recording.

≥For the recording time on a tape, refer to

-9-.

≥Carry out a recording check (

-19-) to verify that

the image is recorded properly.

≥In order to find the unrecorded section, carry out

the blank search (

-20-).

ª

On-screen display in the tape

recording mode

1) Recording time elapse

2) Remaining tape indication

ª

Concerning the remaining tape time

indication on the screen

≥The remaining tape time is indicated in minutes.

(When it reaches less than 3 minutes, the

indication starts flashing.)

≥During a 15 seconds or shorter recording, the

remaining tape time indication may not be

displayed or the remaining tape time may not be

displayed correctly.

≥In some cases, the remaining tape time

indication may display remaining tape time that

is 2 to 3 minutes shorter than the actual

remaining tape time.

Recording check

The last image recorded is played back for 2 to

3 seconds. After checking, the camera will be set

to a recording pause.

≥Set to Tape Recording Mode.

1 Press the joystick to display the icon during

the recording pause. Move the joystick

down until icon 1 appears.

2 Move the joystick left to select the

recording check icon [ ].

≥The [RECORDING CHECK STARTED]

indication appears on the screen of the movie

camera.

;

1)

2)

1

LSQT1171ENG.book 19 ページ２００７年１月１０日　水曜日　午後１時７分

Record mode

20

LSQT1171

Blank search function

Searches for the last part of the image recorded

(unused part of the tape). After the search is

finished, the blank search function is cancelled

and the camera is put into recording pause.

≥Set to Tape Recording Mode.

1 Press the joystick to display the icon during

the recording pause. Move the joystick

down until icon 1 appears.

2 Move the joystick right to select the blank

search icon [ ].

3 When the confirmation message appears,

select [YES] and press the centre of the

joystick.

ª

Stopping blank search midway

through

Move the joystick down to select the [∫] icon.

≥If the cassette tape has no blank part, then the

camera will stop at the end of the tape.

≥The camera stops at a point approx. 1 second

before the end of the last image recorded.

When you start recording at that point, the

image can be recorded seamlessly from the last

image.

Recording a still picture on a tape

(Photoshot)

Still pictures can be recorded from the movie

camera lens.

≥Set to Tape Recording Mode.

1 Press the [ ] button in the recording pause

mode.

≥The movie camera records a still picture for

about 7 seconds and then switches back to

the recording pause mode.

≥If you set [ADVANCED] >> [SHTR EFFECT] >>

[ON], you can add image and a sound like

releasing the shutter.

≥Photoshot recording results in slightly inferior

image quality.

ª

Continuous photoshot

If you set [ADVANCED] >> [SHTR EFFECT] >>

[ON] and keep the [ ] button pressed, the movie

camera will continuously record still pictures in

approx. 0.7 seconds intervals until the button is

released.

≥The screen blinks and, at the same time, a

shutter clicking sound is recorded.

1

LSQT1171ENG.book 20 ページ２００７年１月１０日　水曜日　午後１時７分

Strona jest ładowana ...

Panasonic NVGS60EP Instrukcja obsługi

Panasonic NVGS60EP Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty