AMP Lighting DecoPro ADL-2012-4-B-BZ Instrukcja instalacji

Marka
AMP Lighting
Model
DecoPro ADL-2012-4-B-BZ
Typ
Instrukcja instalacji

Ten podręcznik jest również odpowiedni dla

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP
®
Low Voltage Landscape Lighting
AMP
®
DecoPro LED Deck Light
ADL-2012-4-B-BZ
AMP
®
DecoPro LED Deck Light
ADL-2012-4-B-BZ
Important Safety Instructions: Read Before Installation
INSTALLATION & MAINTENANCE GUIDE
!
www.amplighting.com
–2–
[email protected] • 813.978.3900
Product Dimensions
–3–
Package Contents
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please contact
www.amplighting.com or call 1-813-978-3900.
Important Safety Instructions
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may dam-
age lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
A. (1) Fixture Body
B. (2) Lock Screw
3”
3.5”
1.75”
ProTip for Hiding Lead Wire
ProTip for Hiding Splice Connections
Determine the location for the xture. Drill a hole straight through the
desired mounting location and run the lead wire out the backside of
the location so that the wires are not visible from the front side. Use a
matching trim piece and cut a groove in the back of trim. Cover the lead
wires with the matching trim piece.
All xtures come with 4’ of lead wire enabling you to hide the splice
connections out of sight. If you must make a splice connection in view, use
an inline heat shrink style connection that is less visible than traditional
twist caps.
INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
Install Fixture Body
2
Remove Face Cover
1
[email protected] • 813.978.3900
–5–
Install Face Cover
3
AMP
®
DecoPro LED Deck Light
ADL-2012-4-B-BZ
Wire Connections
4
Rotate the face cover until it
stops and then lift the cover
straight off.
Note: The rst time it may be
difcult because the xture
has a very tight o-ring seal and
a grease sealant for moisture
protection.
Face Cover
Fixture Body
Rotate
Fixture Body
Lock Screw
Wall Anchor
(optional)
Attach the xture body to your
desired location and secure with lock
screws.
Note: Wall anchors may be required
for certain installation conditions
(e.g. Brick walls, Concrete Walls,
etc.). Mark on the wall using holes
on the xture body to drill holes for
your wall anchors. Remove base and
drill proper holes in the wall, then
insert wall anchors.
Hole
Push face cover back onto the
xture body aligned with the gaps
in the xture body. Once the face
cover is ush with the xture body,
rotate the face cover until it stops
and locks into place.
Fixture
Body
Face
Cover
Strip both leads from luminaire
pigtail. Using two wire connectors
(sold separately), connect leads
from luminaire to main supply cable
leads.
Fixture
Wire
Connector
Main Supply Cable
Pigtail
–6–
www.amplighting.com
–6–
[email protected] • 813.978.3900
–7–
IS-ADL-2012-4-B-BZ.ver1
Specications and product details subject to change without notice.
© Copyright 2019, AMP
®
Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

AMP Lighting DecoPro ADL-2012-4-B-BZ Instrukcja instalacji

Marka
AMP Lighting
Model
DecoPro ADL-2012-4-B-BZ
Typ
Instrukcja instalacji
Ten podręcznik jest również odpowiedni dla
ściągnij PDF
raport

w innych językach

Powiązane dokumenty

Inne dokumenty