Classic Exhibits VK-1073 Setup Instructions
- Typ
- Setup Instructions
www.classicexhibits.com
Step 1
Page 1 of 4
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Layout
10’
10’
Plan View
www.classicexhibits.com
Step 2
Page 2 of 4
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C E liateDD liateDDetail B
Detail A
Setscrews
www.classicexhibits.com
Step 1
Page 1 of 4
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Backwall Assembly
Steps:
1) Attach vertical extrusions [2 and 3] to base plates [1 and 1a].
2) Attach horizontal extrusions between vertical extrusions as shown.
3) Lock horizontal extrusions [9 and 13] to pill slots on backwall horizontal bars.
Refer to
Pill Slot Detail Example
detail.
Monitor Mount Location
Thumbscrew Location
Velcro attached to front upper
edge of horizontal extrusion [8].
Velcro attached to front lower
edge of horizontal extrusion [8].
1
2
3
4
5
6
7
8
9
10
9
9
10
1a
Item
1
1a
2
3
4
5
6
7
8
9
10
Qty. For Step
1
1
1
1
1
1
1
1
1
2
2
Description
Base Plate
Base Plate w/ Cut Out
80”h Vertical Square Extrusion
80”h Vertical Square Extrusion
86”w Horizontal Extrusion
86”w Horizontal Extrusion
86”w Horizontal Extrusion
86”w x 5.512”h Horizontal Extrusion
86”w Horizontal Extrusion
9”w Shelf Support
13”w Shelf Support
Pill Slot Detail Example
Pill Slot
*
*
*
*
*
**
*
www.classicexhibits.com
Step 2
Page 2 of 4
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Header Assembly
Steps:
1) Attach header pieces together as shown.
2) Apply graphic to front of assembled header.
3)
Attach assembled header frame to ceiling
by locking to connectors where indicated.
Note: Frame should be assembled from Backside.
A
B
C
D
Backside View
Front View
Lock
Lock
Lock
Lock
Part Number
A
B
C
D
Qty for Step
1
1
1
1
Description
89.965” Lower Horizontal
8.738“ Tapered cut Vertical
14” Tapered cut Vertical
92.9223” Curved Horizontal
NOTE: Header frame must stay assembled when shipping in crate
Assembled Header Frame with Grpahic at Front
Lock
Lock
Connector
Velcro Applied to Front Perimeter of Frame
www.classicexhibits.com
Step 3
Page 3 of 4
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Shelf, Header and Cabinet Attachment
Steps:
1) Slide cabinet box
against backwall horizontal bar and secure with bolts and wing nuts
2) Attach standoff barrels to top of cabinet box.
3) Place lower shelf atop shelf supports and secure to horizontal bar with thumbscrews.
4) Place upper shelf atop shelf supports and rest on standoffs as shown, then secure shelf to horizontal bar using thumbscrews.
5) Attach wing to vertical [3]. Refer to
Example of A10 Clamp Attachment
detail.
6) Attach ceiling with header atop assembled backwall.
Slide cabinet box against
backwall horizontal bar
Rest on Standoff Barrels
Velcro attach shelves to
horizontal shelf supports.
Shelf
Shelf
Ceiling
Wing
When assembled
Header
When desired location
is found, tighten
set screw to secure.
Slide connector on back
of A10 clamp into groove
of extrusion.
Example of A10 Clamp Attachment
Tighten knob to secure
shelf/wing in place.
Thumbscrew Location
*
*
*
*
*
Bolt and Wing Nut Location
Screw to Top
of Cabinet
www.classicexhibits.com
Step 4
Page 4 of 4
© 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Kiosk Assembly
Item
1
2
3
4
5
6
Description
41.5”h Vertical Extrusion
41.5”h Vertical Extrusion
32.5”h Vertical Extrusion
32.5”h Vertical Extrusion
13.5”w Horizontal Extrusion
14.5”w Horizontal Extrusion
Qty. for Step
1
1
1
1
5
4
Steps:
1) Attach lower horiozntal extrusions [5 and 6] between vertical extrusions
2) Place inserts and attach door where indicated, then attach upper horizontals as shown.
3) Velcro shelf supports to inside of assembled base, then set internal shelf atop supports.
4) Place counter top on assembled base.
5) Attach aluminum plate for monitor mount attachment and lit racks to assembled workstation refering to Details below.
1
2
3
4
5
6
Door
Internal Shelf
Connectors for Aluminum
Plate Attachment
Attach connector piece to rack
as shown. Then connect
assembled literature
rack to vertical extrusion.
Literature Rack Attachment
(Place where desired)
Tighten Lock
to Secure
*
**
**
Monitor Mount Attachment
Slide mounting connector
pieces into groove of
extrusion. Tighten setscrew
to secure in place.
Then attach
wall plate to connectors
usingsupplied bolts.
Setscrew
Setscrew
5
5
5
5
6
6
6
Door Stop Door Hinges
Bottom Portion Stay
Assembled when Packing in Crate
www.classicexhibits.com © 2011
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - Crate Packing
Level 1 Level 2
#2
#3
Shelf (short)
Shelf (long)
#3
#5
#4
#7
#4, #5, #6, & #8
(2) #9
(2) #10
Base Plates
Partly
Assembled
Kiosk
Cabinet Box
Wing
Monitor Mount Plate
Pamphlet
Trays (4)
Header Assembly
Ceiling
Kiosk Counter
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Classic Exhibits VK-1073 Setup Instructions
- Typ
- Setup Instructions
w innych językach
- English: Classic Exhibits VK-1073
Powiązane dokumenty
-
Classic Exhibits VK-2914 Setup Instructions
-
-
-
-
-
-
-
-
-