Classic Exhibits VK-1053 Setup Instructions

Classic Exhibits
Marka
Classic Exhibits
Model
VK-1053
Typ
Setup Instructions
www.classicexhibits.com
Step 1
Page 1 of 6
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1053 - General Layout
Plan View 10’
10’
www.classicexhibits.com
Step 2
Page 2 of 6
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - General Information
The Tool Typical Connection
Horizontal Inline Connection (remove only one setscrew)
Base Plate Connection Vertical Connection
(remove only two setscrews)
Most Visionary Designs exhibits can be
assembled with the supplied Hex Key Tool.
Occasionally, a flat head screwdriver may
be required.
Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock
and creates a strong positive connection.
Remove only (1) setscrew when disassembling. Replace setscrew in
extrusion after assembling it. Before packing, replace setscrew in
extrusion to avoid losing it.
Attach base plate to round or square
vertical extrusion using the bolt provided.
Be careful not to strip the threads.
When vertical extrusions are packed in
portable cases rather than crates or
tubs, they must broken down into
smaller sections which then require
assembly.
Remove only (2) setscrews when
disassembling. Replace setscrews in
extrusion after assembling it. Before
packing, replace setscrews in extrusion
to avoid losing them.
Using Your Setup Instructions
The Visionary Designs Setup Instructions are created specifically for your
configuration. They are laid out sequentially, including an exploded view of
the entire display, and then a logical series of detailed steps to assemble the
main structure and components. We encourage you to study the instructions
before attempting to assemble your exhibit.
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in RED).
This is VERY IMPORTANT.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or countertops, use mild cleansers and a
soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing material. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Typical Connection (cont’d)
Numbered Label
Each extrusion contains a numbered label which
corresponds with setup instructions.
The label is located within a groove of the extrusion
(when possible). With Visionary Designs the labels
contain Black numbers unless otherwise specified.
Detail C E liateDD liateDDetail B
Detail A
Setscrews
www.classicexhibits.com
Step 1
Page 1 of 6
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1053 - Backwall Alcove Tower Assembly
1
1A
2
2A
4
4A
5
6
7
8
9
10
4A
4
3
Item
1/1A
2/2A
3
4
5
6
7
8
9
10
Qty.
1/1
1/1
1
2/2
1
1
1
1
1
1
Description
47.5”h Vertical Extrusion
47.5”h Vertical Extrusion
43.17”h Z45 Vertical Extrusion w/ door stops
23.93”w Z45 Curved Horizontal Extrusions
19”w x 47.5”h LT-Panel
90° LT-Panel Connector
23”w x 47.5”h LT-Panel
23”w x 47.5”h LT-Panel
90° LT-Panel Connector
19”w x 47.5”h LT-Panel
Steps:
1) Connect horizontal extrusions [4] together.
See Horizontal Connection detail.
Repeat step for horizontals [4A].
2) Attach assembled horizontals between verticals [1] & [2].
3) Connect vertical extrusion [3] between
horizontal extrusion assemblies [4] & [4A].
NOTE: Connect at seam of assembled extrusions.
4) Connect LT-Panels and LT-Connectors in
numerical order. Refer to General Information.
5) Attach vertical [1A] to vertical [1].
See Vertical Connector detail.
Repeat step of vertical [2A].
Screws
Connector
Vertical Connector
1) Insert Connector into
lower vertical extrusion.
2) Slide upper vertical over
connector; secure.
Screws
*Keep all screws attached to
connector pieces when
disassembling to prevent loss*
*
Horizontal Connection
*
*
PR53
**
www.classicexhibits.com
Step 2
Page 2 of 6
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1053 - Backwall Alcove Tower Assembly Cont’d
5
6
7
8
9
10
4C
4C
4D
4D
Item
4C/4D
5
6
7
8
9
10
Qty.
2/2
1
1
1
1
1
1
Description
23.93”w Z45 Curved Horizontal Extrusions
19”w x 47.5”h LT-Panel
90° LT-Panel Connector
23”w x 47.5”h LT-Panel
23”w x 47.5”h LT-Panel
90° LT-Panel Connector
19”w x 47.5”h LT-Panel
Steps:
1) Connect horizontal extrusions [4C] together.
See Horizontal Connection detail.
Repeat step for horizontals [4D].
2) Attach assembled horizontals between verticals [1A] & [2A].
3) Connect LT-Panels and LT-Connectors in
numerical order. Refer to General Information.
4) Attach vertical [1A] to vertical [1].
See Vertical Connector detail.
Repeat step of vertical [2A].
Horizontal Connection
PR53
*
*
*
www.classicexhibits.com
Step 3
Page 3 of 6
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1053 - Backwall Alcove Tower Assembly Cont’d
Steps:
1) Connect Shelf Supports to interior of assembled tower.
2) Place internal shelf on top of installed shelf supports.
3) Insert counter top into tower and attach using thumb screws.
See Counter Top Attachment detail.
4) Hang assembled doors on hinges.
See Door Attachment detail.
Door
Hinge
Hinge
Door Attachment
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
*
Thumbscrew Backwall
Internal Shelf
Shelf Supports
Shelf Supports
Shelf Supports
Shelf Supports
Shelf Supports
Counter
Insert Counter into alcove of assembled tower.
Attach counter to backwall using thumbscrews
provided. Tighten to secure in place.
Counter Top Attachment
*
**
*
*
*
*
www.classicexhibits.com
Step 4
Page 4 of 6
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1053 - Backwall Assembly
Velcro: Top
Edge
Velcro: Bottom
Edge
Velcro: Bottom
Edge
Velcro: Top
Edge
Back View
When assembled
1/1A
2/2A
11
11A
14A
14
13
13A
12A
12
Item
11/11A
12/12A
13/13A
14/14A
Qty.
1/1
1/1
1/1
1/1
Description
47.5”h Vertical Extrusion
47.5”h Vertical Extrusion
30”w Z45 Horizontal Extrusion
30”w Z45 Horizontal Extrusion
Steps:
1) Connect Vertical extrusions [11] & [11A] together.
See Vertical Connector detail.
Repeat step for horizontals [12] & [12A].
2) Attach horizontals [13] & [13A] between verticals [1/1A] & [11/11A].
3) Attach horizontals [14] & [14A] between verticals [2/2A] & [12/12A].
4) Apply Fabric graphics to back side of assembled frame.
Screws
Connector
Vertical Connector
1) Insert Connector into
lower vertical extrusion.
2) Slide upper vertical over
connector; secure.
Screws
*Keep all screws attached to
connector pieces when
disassembling to prevent loss*
*
*
*
www.classicexhibits.com
Step 5
Page 5 of 6
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX -
Connections are made by holding the button
down and sliding the red tube into opposing
tube until the connection is made. To disassemble
push button and pull or twist extrusions apart.
Push-Button
Push-Button
66
6
6
Numbered Label
Using Your Setup Instructions
The Aero Overhead Sign Setup Instructions are created specically for your conguration. They include an
exploded view of the frame which is sequentially numbered. We encourage you to study the instructions
before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-button
connectors and pre-connected horizontal sections.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
VK-1053 - Canopy Assembly
When assembled
A
A
D
D
B
B
C
C
Steps:
1) Assemble canopy in alphabetical order, matching letters.
2) Apply Pillowcase Graphic to assembled canopy.
3) Connect canopy to top of assembled backwall.
www.classicexhibits.com
Step 6
Page 6 of 6
866.652.2100
© 2015
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #XXXXX - VK-1053 - Reception Counter Assembly
Item
1
2
3
4
5
6
7
8
Description
38”h Vertical Extrusion
38”h Vertical Extrusion
38”h Vertical Extrusion
38”h Vertical Extrusion
21.2810”w Horizontal Extrusion
10.75”w Horizontal Extrusion
21.2810”w Horizontal Extrusion
10.75”w Horizontal Extrusion
Qty
1
1
1
1
2
2
2
2
1
2
3
4
5
65
6
7
87
8
Steps:
1) Connect horizontal extrusions [5 and 6] between vertical extrusions [1, 2, 3 and 4]
resting atop stoppers at approximately 4” up from floor to bottom of metal.
2) Set floor in place atop lip of horizontal extrusions.
3) Place doors and inserts in place as shown.
4) Connect horizontal extrusions [7, and 8] between vertical extusions [1, 2, 3 and 4]
and atop inserts and door.
5) Velcro shelf supports to inside of pedestal, then set internal shelf on top of supports.
6) Attach iPad to bottom of counter. Refer to detail.
7) Place counter top on assembled pedestal.
*
*
Slide pin into
hinge attached to
Round Vertical.
Slide Door hinge
over pin.
Door
Hinge
Pin
Hinge
Door Attachment
Shelf Support
4”
Stopper at 4”
Graphic
Cap
Standoff
Barrel
Slide connector on back of
standoff barrels into groove
of extrusion and twist to
secure in place. Secure graphic
to standoffs using screw caps.
Graphic Attachment
Shelf
When
assembled
Door
Floor
Hinges
Door Stop
iPad
Bottom View
of Counter
Six Thumbscrews
iPad Insert
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Classic Exhibits VK-1053 Setup Instructions

Classic Exhibits
Marka
Classic Exhibits
Model
VK-1053
Typ
Setup Instructions
ściągnij PDF
raport

w innych językach

Powiązane dokumenty

Inne dokumenty