Velleman DVM898 Instrukcja obsługi

DVM898

DIGITAL MULTIMETER - 6000 COUNTS

DIGITALE MULTIMETER - 6000 COUNTS

MULTIMÈTRE NUMÉRIQUE - 6000 POINTS

MULTÍMETRO DIGITAL - 6000 CUENTAS

DIGITAL-MULTIMETER - 6000 ZÄHLUNGEN

MULTIMETR CYFROWY - WARTOŚCI DO 6000

MULTÍMETRO DIGITAL - CONTAGEM ATÉ 6000

CAT. III 600 V / CAT. IV 300 V

USER MANUAL 3

HANDLEIDING 16

MODE D'EMPLOI 30

MANUAL DEL USUARIO 45

BEDIENUNGSANLEITUNG 59

INSTRUKCJA OBSŁUGI 73

MANUAL DO UTILIZADOR 88

DVM898

V. 03 – 06/04/2021 2 ©Velleman nv

DVM898

V. 03 – 06/04/2021 3 ©Velleman nv

USER MANUAL

1. Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal

of the device after its lifecycle could harm the environment. Do

not dispose of the unit (or batteries) as unsorted municipal

waste; it should be taken to a specialized company for recycling.

This device should be returned to your distributor or to a local

recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing Velleman! Please read the manual thoroughly before

bringing this device into service. If the device was damaged in transit, do

not install or use it and contact your dealer.

2. Used Symbols

AC (Alternating Current)

DC (Direct Current)

Both AC and DC

Risk of Electric shock. A potentially hazardous voltage is

possible.

Caution: risk of danger, refer to the user manual for safety

information.

Warning: a hazardous condition or action that may result in

injury or death

Caution: condition or action that may result in damage to the

meter or equipment under test

Double insulation (class 2-protection)

Earth

Fuse

Capacitor

Diode

Continuity

DVM898

V. 03 – 06/04/2021 4 ©Velleman nv

3. General Guidelines

Refer to the Velleman® Service and Quality Warranty on the last pages of

this manual.

This symbol indicates: Read instructions

Not reading the instructions and manual can lead to damage,

injury or death.

This symbol indicates: Danger

A hazardous condition or action that may result in injury or death

This symbol indicates: Risk of danger/damage

Risk of a hazardous condition or action that may result in

damage, injury or death

This symbol indicates: Attention; important information

Ignoring this information can lead to hazardous situations.

WARNING: To avoid electrical shock always disconnect the test

leads prior to opening the housing. To prevent fire hazards, only

use fuses with the same ratings as specified in this manual.

Remark: refer to the warning on the battery compartment

Avoid cold, heat and large temperature fluctuations. When the

unit is moved from a cold to a warm location, leave it switched

off until it has reached room temperature. This to avoid

condensation and measuring errors.

Protect this device from shocks and abuse. Avoid brute force

when operating.

Pollution degree 2-device. For indoor use only. Keep this device

away from rain, moisture, splashing and dripping liquids. Not for

industrial use. Refer to §8 Pollution degree.

Keep the device away from children and unauthorised users.

Risk of electric shock during operation. Be very careful when

measuring live circuits.

There are no user-serviceable parts inside the device.

Refer to an authorized dealer for service and/or spare parts.

DVM898

V. 03 – 06/04/2021 5 ©Velleman nv

This is an installation category CAT IV measuring

instrument. Refer to §7 Overvoltage/installation category.

Read this addendum and the manual thoroughly. Familiarise

yourself with the functions of the device before actually using it.

All modifications of the device are forbidden for safety reasons.

Damage caused by user modifications to the device is not

covered by the warranty.

Only use the device for its intended purpose. Using the device in

an unauthorized way will void the warranty. Damage caused by

disregard of certain guidelines in this manual is not covered by

the warranty and the dealer will not accept responsibility for any

ensuing defects or problems.

4. Maintenance

There are no user-serviceable parts inside the device.

Refer to an authorized dealer for service and/or spare parts.

Before performing any maintenance activities, disconnect the test leads

from the jacks.

For instructions on replacing battery or fuse, refer to §11 Battery and fuse

replacement.

Do not apply abrasives or solvents to the meter. Use a damp cloth and mild

detergent for cleaning purposes.

5. During Use

Risk of electric shock during operation. Be very careful when

measuring live circuits.

• Never exceed the limit value for protection. This limit value is listed

separately in the specifications for each range of measurement.

• Do not touch unused terminals when the meter is linked to a circuit

which is being tested.

• Never use the meter with CAT III installations when measuring voltages

that might exceed the safety margin of 600 V above earth ground.

Never use the meter with CAT IV installations when measuring voltages

that might exceed the safety margin of 300 V above earth ground.

• Set the range selector at its highest position if the intensity of the

charge to be measured is unknown beforehand.

• Disconnect the test leads from the tested circuit before rotating the

range selector in order to change functions.

• When carrying out measurements on a TV set or switching power

circuits, always remember that the meter may be damaged by any high

amplitude voltage pulses at test points.

DVM898

V. 03 – 06/04/2021 6 ©Velleman nv

• Always be careful when working with voltages above 60 VDC or 30 VAC

rms. Keep your fingers behind the probe barriers at all times during

measurement.

• Never perform resistance, diode or continuity measurements on live

circuits. Make sure all capacitors in the circuit are depleted.

6. General Description

Refer to the illustration on page 2 of this manual:

1. Display

3 ½ digits, 7 segments, LCD: 60 x 28 mm

2. Function buttons

3. Selection button

4. “15A” jack

Insert the red test lead in this connector in order to measure a max.

current of 15 A.

5. “µAmA” jack

Insert the red (positive) test lead in this connector to measure current

(except 10 A).

6. “COM” jack

Insert the black (negative) test lead.

7. “VHz” jack

Insert the red (positive) test lead in this connector to measure voltage,

resistance and frequency.

7. Overvoltage/Installation Category

DMMs are categorized depending on the risk and severity of transient

overvoltage that might occur at the point of test. Transients are short-lived

bursts of energy induced in a system, e.g. caused by lightning strike on a

power line.

The existing categories according EN 61010-1 are:

CAT I

A CAT I-rated meter is suitable for measurements on protected

electronic circuits that are not directly connected to mains power, e.g.

electronics circuits, control signals…

CAT

II

A CAT II-rated meter is suitable for measurements in CAT I-

environments and mono-phase appliances that are connected to the

mains by means of a plug and circuits in a normal domestic

environment, provided that the circuit is at least 10 m apart from a

CAT III- or 20 m apart from a CAT IV-environment. E.g. household

appliances, portable tools…

DVM898

V. 03 – 06/04/2021 7 ©Velleman nv

CAT

III

A CAT III-rated meter is suitable for measurements in CAT I- and

CAT II-environments, as well as for measurements on (fixed) mono-

or poly-phased appliances which are at least 10 m apart from of a

CAT IV-environment, and for measurements in or on distribution level

equipment (fuse boxes, lighting circuits, electric ovens).

CAT

IV

A CAT IV-rated meter is suitable for measuring in CAT I-, CAT II- and

CAT III-environments as well as on the primary supply level.

Note that for all measurements on equipment for which the supply

cables run outdoors (either overhead or underground) a CAT IV

meter must be used.

Warning:

This device was designed in accordance with EN 61010-1 installation

category CAT III 600 V and CAT IV 300 V. This implies that certain

restrictions in use apply that are related to voltages and voltage peaks

which can occur within the environment of use. Refer to the table above.

This device is only suitable for measurements up to 600 V in

CAT III and up to 300 V in CAT IV

8. Pollution Degree

IEC 61010-1 specifies different types of pollution environments, for which

different protective measures are necessary to ensure safety. Harsher

environments require more protection, and the protection against the

pollution which is to be found in a certain environment depends mainly on

the insulation and the enclosure properties. The pollution degree rating of

the DVM indicates in which environment the device may be used.

Pollution

degree 1

No pollution or only dry, nonconductive pollution occurs. The

pollution has no influence. (only to be found in hermetically

sealed enclosures)

Pollution

degree 2

Only nonconductive pollution occurs. Occasionally, temporary

conductivity caused by condensation is to be expected.(home

and office environments fall under this category)

Pollution

degree 3

Conductive pollution occurs, or dry nonconductive pollution

occurs that becomes conductive due to condensation that is

to be expected.

(industrial environments and environments exposed to

outside air - but not in contact with precipitation)

Pollution

degree 4

The pollution generates persistent conductivity caused by

conductive dust or by rain or snow. (exposed outdoor

environments and environments where high humidity levels

or high concentrations of fine particles occur)

DVM898

V. 03 – 06/04/2021 8 ©Velleman nv

Warning: This device was designed in accordance with EN 61010-1

pollution degree 2. This implies that certain restrictions in use apply that

are related to pollution which can occur within the environment of use. Refer

to the table above.

This device is only suitable for measurements in Pollution

degree class 2 environments.

9. Specifications

This device is not calibrated when purchased!

Regulations concerning environment of use:

Use this meter only for measurements in CAT I, CAT II, CAT III and CAT IV

environments (see §7).

Use this meter only in a pollution degree 2 environment (see §8).

Ideal working conditions include:

temperature: 0 °C to 40 °C (32 °F to 104 °F)

relative humidity: max. 80 %

altitude: max. 2000 m (6560 ft)

voltage ........................................................................... 600 V

fuse protection

F0.5 A/600 V, 5 x 20 mm

F15 A/1000 V, 5 x 20 mm

power supply ................................................. 1 x 9 V 6F22 (incl.)

display ............................................................ LCD, 6000 counts

display dimensions ................................................... 60 x 28 mm

over-range .......................................................................... yes

continuity buzzer .................................................................. yes

diode test ............................................................................ yes

low-battery indication ........................................................... yes

ranging mode ...................................................... auto + manual

data hold ............................................................................ yes

backlight ............................................................................. yes

auto power-off ..................................................................... yes

dimensions ..................................................... 177 x 92 x 40 mm

weight (with battery) ......................................................... 320 g

storage environment

temperature ................................................. -20 °C to 60 °C

humidity ............................................................ < 90 % RH

test lead probe ......... CAT III 1000 V/CAT IV 600 V, 15 A; L = 75 cm

DVM898

V. 03 – 06/04/2021 9 ©Velleman nv

9.1 DC VOLTAGE

Do not measure circuits that may contain voltages

> 600 VDC or > 600 VAC

range

resolution

accuracy

60.00 mV

0.01 mV

± (0.8 % rdg + 2 digits)

600.0 mV

0.1 mV

± (0.5 % rdg + 2 digits)

6.000 V

1 mV

60.00 V

10 mV

600.0 V

100 mV

600 V

1 V

± (0.8 % rdg + 2 digits)

Overload protection: 600 V DC or AC rms

Impedance: 10 MΩ, > 100 MΩ for 60 mV/600 mV range

9.2 AC VOLTAGE

Do not measure circuits that may contain voltages

> 600 VDC or > 600 VAC

range

resolution

accuracy

60.00 mV

0.01 mV

± (1.2 % rdg + 3 digits)

600.0 mV

0.1 mV

6.000 V

1 mV

± (0.8 % rdg + 3 digits)

60.00 V

10 mV

600.0 V

100 mV

600 V

1 V

± (1.8 % rdg + 3 digits)

AC true rms

Frequency range: 40 Hz-1 kHz

Overload protection: 600 V DC or AC rms

Impedance: 10 MΩ, > 100 MΩ for 60 mV/600 mV range

9.3 DC CURRENT

Do not measure circuits that may contain voltages

> 600 VDC or > 600 VAC

range

resolution

accuracy

600 µA

0.1 µA

± (1.2 % rdg + 2 digits)

6000 µA

1 µA

60 mA

10 µA

600 mA

100 µA

DVM898

V. 03 – 06/04/2021 10 ©Velleman nv

6 A

1 mA

± (2.0 % rdg + 3 digits)

15 A

10 mA

Overload protection: F0.5 A/600 V fuse, F15 A/600 V fuse

Continuous testing max. steady-state current of 1 A

9.4 AC CURRENT

Do not measure circuits that may contain voltages

> 600 VDC or > 600 VAC

range

resolution

accuracy

600 µA

0.1 µA

± (1.5 % rdg + 3 digits)

6000 µA

1 µA

60 mA

10 µA

600 mA

100 µA

6 A

1 mA

± (2.5 % rdg + 5 digits)

15 A

10 mA

AC true rms

Frequency range: 40 Hz-1 kHz

Overload protection: F0.8 A/600 V fuse, F15 A/600 V fuse

Continuous testing max. steady-state current of 1 A

9.5 RESISTANCE

Do not conduct resistance measurements on live

circuits

range

resolution

accuracy

600 Ω

0.1 Ω

± (1.0 % rdg + 3 digits)

6 kΩ

1 Ω

± (1.0 % rdg + 2 digits)

60 kΩ

10 Ω

600 kΩ

100 Ω

6 MΩ

1 kΩ

60 MΩ

10 kΩ

± (1.5 % rdg + 3 digits)

Overload protection: 600 V DC or AC rms

DVM898

V. 03 – 06/04/2021 11 ©Velleman nv

9.6 CAPACITANCE

Do not conduct capacitance measurements on live

circuits

range

resolution

accuracy

9.999 nF

1 pF

± (3.0 % rdg + 10 digits)

99.99 nF

10 pF

± (2.5 % rdg + 5 digits)

999.9 nF

100 pF

9.999 µF

1 nF

99.99 µF

10 nF

± (5.0 % rdg + 10 digits)

999.9 µF

100 nF

± (10.0 % rdg + 20 digits)

9.999 mF

1 µF

99.99 mF

10 µF

Overload protection: 600 V DC or AC rms

9.7 DIODE AND CONTINUITY

Do not conduct diode or continuity measurements on

live circuits

range

description

test condition

display reads the

approximate forward

voltage of the diode

forward DC current ± 1.5 mA

reversed DC voltage ± 3.2 V

built-in buzzer sounds

if resistance < 50 Ω

open-circuit voltage ± 1.0 V

Overload protection: 600 V DC or AC rms

9.8 FREQUENCY

Do not conduct frequency measurements on live circuits

range

resolution

accuracy

9.999 Hz

0.001 Hz

± (0.1 % rdg + 5 digits)

99.99 Hz

0.01 Hz

999.9 Hz

0.1 Hz

9.999 kHz

1 Hz

99.99 kHz

10 Hz

DVM898

V. 03 – 06/04/2021 12 ©Velleman nv

999.9 kHz

100 Hz

9.999 MHz

1 kHz

Sensitivity: sine wave 0.6 V rms (9.999 MHz: 1.5 V rms)

Overload protection: 600 V DC or AC rms

9.9 DUTY CYCLE

0.1 %-99.9 %: ± (2.0 % rdg + 2 digits)

Frequency < 10 kHz

Sensitivity: sine wave 0.6 V rms

Overload protection: 600 V DC or AC rms

9.10 TEMPERATURE

range

resolution

accuracy

°C/°F

1 °C/1 °F

-20 °C-150 °C

-4 °F-302 °F

± (3 °C + 1)

± (5 °F + 2)

151 °C-1000 °C

303 °F-1832 °F

± (3 % + 2)

± (3 % + 3)

NiCr-NiSi sensor

Overload protection: 600 V DC or AC rms

10. Operation

10.1 VOLTAGE MEASUREMENT

Do not measure circuits that may contain voltages > 600 VDC or

> 600 VAC

Use extreme caution when measuring voltages higher than 60 VDC

or 30 VAC rms.

Always place your fingers behind the protective edges of the test

probes while measuring!

1. Set the rotary switch in the desired “ ” or “ ”position.

2. Press “SELECT” to choose the AC or DC measurement mode.

3. Connect the red test lead to the “VHz” jack and the black lead to the

“COM” jack.

4. Connect the test leads to the source being measured.

5. Read the voltage value and the polarity of the red test lead on the LCD

display.

Notes

• In the AC range, press “Hz%” to measure the frequency or duty cycle.

DVM898

V. 03 – 06/04/2021 13 ©Velleman nv

10.2 CURRENT MEASUREMENT

Do not measure circuits that may contain voltages > 600 VDC or

> 600 VAC

Use extreme caution when measuring voltages higher than 60 VDC

or 30 VAC rms.

Always place your fingers behind the protective edges of the test

probes while measuring!

1. Set the rotary switch in the desired “ ”, “ ” or “ ” position.

2. Press “SELECT” to choose the AC or DC measurement mode.

3. Connect the red test lead to the “µAmA” jack and the black test lead to

the “COM” jack (switch the red lead to the “15A” jack for

measurements between 600 mA and 15 A).

4. Open the circuit in which the current is to be measured and connect

the test leads to the circuit IN SERIES.

5. Read the current value and the polarity of the red lead connection on

the LCD display.

Notes

• In the AC range, press “Hz%” to measure the frequency or duty cycle.

10.3 RESISTANCE MEASUREMENT

Do not conduct resistance measurements on live circuits. Make sure

all capacitors in the circuit are depleted.

1. Set the rotary switch in the “Ω ” position.

2. Connect the red test lead to the “VHz” jack and the black test lead to

the “COM” jack.

3. Connect the test leads to the resistor to be measured and read the

LCD display.

10.4 CAPACITANCE MEASUREMENT

Do not conduct capacitance measurements on live circuits. Make

sure all capacitors in the circuit are depleted.

1. Set the rotary switch in the “Ω ” position.

2. Press “SELECT” to choose the capacitance measurement mode.

3. Connect the red test lead to the “VHz” jack and the black test lead to

the “COM” jack.

DVM898

V. 03 – 06/04/2021 14 ©Velleman nv

4. Connect the test leads to the source being measured and read the LCD

display.

10.5 DIODE AND CONTINUITY TEST

Do not conduct diode or continuity measurements on live circuits.

Make sure all capacitors in the circuit are depleted.

1. Set the rotary switch in the “Ω ” position.

2. Press “SELECT” to choose the diode or continuity measurement mode.

3. Connect the red test lead to “VHz” jack and the black one to the

“COM” jack.

4. For measuring the diode, connect the red test lead to the anode of the

diode to be tested and the black test lead to the cathode of the diode.

The approx. forward voltage drop of the diode will be displayed.

For measuring continuity, connect the test leads to two points of the

circuit to be tested. If continuity exists, the built-in buzzer will sound.

10.6 FREQUENCY AND DUTY CYCLE MEASUREMENT

Do not conduct frequency or duty cycle measurements on live

circuits.

1. Set the rotary switch in the “Hz” position.

2. Press “Hz%” to choose the frequency or duty cycle measurement

mode.

3. Connect the red test lead to “VHz” jack and the black one to the

“COM” jack.

4. Connect the test leads to the source being measured and read the LCD

display.

10.7 TEMPERATURE MEASUREMENT

1. Set the rotary switch in the “°C/°F” position.

2. Press “SELECT” to choose the Celsius or Fahrenheit measurement

mode.

3. Connect the red banana plug to the “VHz” jack and the black plug to

the “COM” jack.

4. Connect the banana plugs to the source being measured and read the

LCD display.

10.8 DATA HOLD

Press “ ” to lock the displayed value. Press again to exit.

DVM898

V. 03 – 06/04/2021 15 ©Velleman nv

10.9 BACKLIGHT

Hold “ ”pressed for 2 seconds to switch the backlight on or off. The

backlight will also switch off automatically.

10.10 RELATIVE MEASUREMENT

Press “ ” to measure the relative value or to exit the function.

10.11 MAXIMUM VALUE

Press “MAX/MIN” to lock/unlock the maximum/minimum measured value on

the LCD.

10.12 AUTO/MANUAL RANGE

Repeatedly press “RANGE” until the desired range is displayed. Hold the

button pressed to return to the automatic range selection mode.

Notes

• In manual range selection mode, select a higher range when “OL” is

displayed.

11. Battery and Fuse Replacement

WARNING: To avoid electrical shock always disconnect the test

leads prior to opening the housing. To prevent fire hazards, only use

fuses with the same ratings as specified in this manual.

Remark: refer to the warning on the battery compartment

There are no user-serviceable parts inside the device.

Refer to an authorized dealer for service and/or spare parts.

Equipment must be isolated or disconnected from the HAZARDOUS

LIVE voltage before access (referring to battery replacement by

operator).

• When" " is displayed, the battery should be replaced.

• Fuses rarely need replacement and blown fuses almost always result

from human error.

To replace the battery:

• Switch of the meter.

• Remove the screw at the back of the case and gently open the housing.

• Remove the old battery and insert a new one.

• Close the housing and fasten the screw.

Battery: 1x 6F22, make sure to respect the polarity

DVM898

V. 03 – 06/04/2021 16 ©Velleman nv

Fuses: F0.5 A/600 V, 5 x 20 mm; F15 A/1000 V, 5 x 20 mm

Make sure the meter is closed tight and put the protective edge back in

place before using the meter.

12. Troubleshooting

If the device acts abnormal while measuring, this means that the internal

fuse is defective.

Keep in mind that a low battery level could lead to incorrect measurements.

Replace the battery on a regular basis.

(tip: the reduced luminosity of the backlight/LCD display indicates a low

battery level)

Use this device with original accessories only. Velleman nv cannot

be held responsible in the event of damage or injury resulting from

(incorrect) use of this device. For more info concerning this product

and the latest version of this manual, please visit our website

www.velleman.eu. The information in this manual is subject to

change without prior notice.

The copyright to this manual is owned by Velleman nv. All

worldwide rights reserved. No part of this manual may be copied,

reproduced, translated or reduced to any electronic medium or otherwise

without the prior written consent of the copyright holder.

HANDLEIDING

1. Inleiding

Aan alle ingezetenen van de Europese Unie

Belangrijke milieu-informatie betreffende dit product

Dit symbool op het toestel of de verpakking geeft aan dat, als het na zijn

levenscyclus wordt weggeworpen, dit toestel schade kan

toebrengen aan het milieu. Gooi dit toestel (en eventuele

batterijen) niet bij het gewone huishoudelijke afval; het moet bij

een gespecialiseerd bedrijf terechtkomen voor recyclage. U moet

dit toestel naar uw verdeler of naar een lokaal recyclagepunt

brengen. Respecteer de plaatselijke milieuwetgeving.

Hebt u vragen, contacteer dan de plaatselijke autoriteiten

betreffende de verwijdering.

Dank u voor uw aankoop! Lees deze handleiding grondig door voor u het

toestel in gebruik neemt. Werd het toestel beschadigd tijdens het transport,

installeer het dan niet en raadpleeg uw dealer.

DVM898

2. Gebruikte symbolen

AC (wisselstroom)

DC (gelijkstroom)

Zowel wissel- als gelijkstroom

Elektrocutiegevaar. Er kan een potentieel gevaarlijke

spanning aanwezig zijn.

Opgelet: Risico op gevaar, lees de gebruikershandleiding.

Waarschuwing: gevaarlijke toestand of actie die kan leiden

tot letsel of de dood

Opgelet: Een onvoorzichtig gebruik kan de multimeter of het

toestel dat u wilt testen beschadigen.

Dubbele isolatie (klasse II-bescherming)

Aarding

zekering

Capaciteit (condensator)

Diode

Continuïteit

3. Algemene richtlijnen

Raadpleeg de Velleman® service- en kwaliteitsgarantie achteraan deze

handleiding.

Dit symbool betekent Instructies lezen

Het niet lezen van deze instructies en de handleiding kan leiden

tot beschadiging, letsel of de dood.

Dit symbool betekent Gevaar

Gevaarlijke toestand of actie die kan leiden tot letsel of de dood

Dit symbool betekent Risico op gevaar/schade

Risico op het ontstaan van een gevaarlijke toestand of actie die

kan leiden tot schade, letsel of de dood

Dit symbool betekent Opgelet; belangrijke informatie

Het niet in acht nemen van deze informatie kan leiden tot een

gevaarlijke toestand.

DVM898

WAARSCHUWING: Om elektrische schokken te vermijden,

ontkoppel altijd de meetsnoeren alvorens de behuizing te

openen. Om brand te voorkomen gebruik enkel zekeringen met

dezelfde specificaties zoals aangegeven in de handleiding.

Opmerking: zie waarschuwing op de achterkant van het toestel

Vermijd koude, hitte en grote temperatuurschommelingen. Als

het toestel van een koude naar een warme omgeving verplaatst

wordt, laat het toestel dan eerst voldoende op temperatuur

komen. Dit om meetfouten en condensvorming te vermijden.

Bescherm tegen schokken. Vermijd brute kracht tijdens de

bediening.

Vervuilingsgraad 2-toestel. Enkel geschikt voor gebruik

binnenshuis! Bescherm het toestel tegen regen, vochtigheid en

opspattende vloeistoffen. Niet geschikt voor industrieel gebruik.

Zie §8 Vervuilingsgraad.

Houd dit toestel uit de buurt van kinderen en onbevoegden.

Elektrocutiegevaar tijdens het gebruik van deze

multimeter. Wees voorzichtig tijdens het meten van een circuit

onder spanning.

Er zijn geen onderdelen in het toestel die door de gebruiker

gerepareerd kunnen worden.

Contacteer uw verdeler voor eventuele reserveonderdelen.

Dit meetinstrument behoort tot de installatiecategorie CAT

IV. Zie §7 Overspanning-/installatiecategorie.

Lees het addendum en deze handleiding zorgvuldig door. Leer

eerst de functies van het toestel kennen voor u het gaat

gebruiken.

Om veiligheidsredenen mag u geen wijzigingen aanbrengen.

Schade door wijzigingen die de gebruiker heeft aangebracht aan

het toestel valt niet onder de garantie.

Gebruik het toestel enkel waarvoor het gemaakt is. Bij

onoordeelkundig gebruik vervalt de garantie. De garantie geldt

niet voor schade door het negeren van bepaalde richtlijnen in

deze handleiding en uw dealer zal de verantwoordelijkheid

afwijzen voor defecten of problemen die hier rechtstreeks

verband mee houden.

DVM898

4. Maintenance

Er zijn geen onderdelen in het toestel die door de gebruiker

gerepareerd kunnen worden.

Contacteer uw verdeler voor eventuele reserveonderdelen.

Ontkoppel de meetsnoeren van de aansluitingen voor het onderhoud of de

reiniging.

Voor informatie over het vervangen van de batterijen en de zekering, zie

§11 Batterijen en zekeringen vervangen.

Gebruik nooit agressieve schuur- of oplosmiddelen. Reinig de meter enkel

met een vochtige doek en een zachte detergent.

5. Tijdens het gebruik

Elektrocutiegevaar tijdens het gebruik van deze multimeter.

Wees voorzichtig tijdens het meten van een circuit onder spanning.

• Overschrijd nooit de grenswaarden. Deze waarde wordt afzonderlijk in

de technische gegevens van elk meetbereik vermeld.

• Raak geen ongebruikte aansluitingen aan wanneer de meter gekoppeld

is aan een meetcircuit.

• Gebruik de meter nooit voor categorie III-installaties bij

spanningsmetingen die de veiligheidsmarge van 600 V boven het

massapotentiaal (kunnen) overschrijden.

Gebruik de meter nooit voor categorie IV-installaties bij

spanningsmetingen die de veiligheidsmarge van 300 V boven het

massapotentiaal (kunnen) overschrijden.

• Plaats de bereikschakelaar in de hoogste stand indien u de intensiteit

van de belasting niet op voorhand kent.

• Ontkoppel de meetsnoeren van het meetcircuit alvorens u aan de

draaischakelaar draait.

• Wanneer u metingen uitvoert op een tv of een schakelende voeding,

mag u niet vergeten dat een sterke stroomstoot ter hoogte van de

geteste punten de meter kan beschadigen.

• Wees uiterst voorzichtig bij metingen > 60 VDC of > 30 VAC rms. Houd

tijdens metingen uw vingers achter de beschermingsrand van de

meetpennen.

• Voer nooit weerstands-, diode- of continuïteitsmetingen uit in circuits

waarop spanning aanwezig is. Zorg ervoor dat alle condensatoren in het

circuit volledig ontladen zijn.

DVM898

6. Algemene omschrijving

Raadpleeg de afbeeldingen op pagina 2 van deze handleiding:

1. Display

3 ½-digits, 7 segmenten, LCD: 60 x 28 mm

2. Functieknoppen

3. Keuzeschakelaar

4. “15A”-bus

Sluit het rode (+) meetsnoer aan op deze bus om een max. stroom

van 15 A te meten.

5. “µAmA”-bus

Sluit het rode (+) meetsnoer aan op deze bus om stroom (uitgez. 10

A) te meten.

6. “COM”-bus

Sluit het zwarte (-) meetsnoer aan.

7. “VHz”-bus

Sluit het rode meetsnoer (+) aan op deze bus om spanning, weerstand

en frequentie te meten.

7. Overspannings-/installatiecategorie

DMM’s worden opgedeeld volgens het risico op en de ernst van

spanningspieken die kunnen optreden op het meetpunt. Spanningspieken

zijn kortstondige uitbarstingen van energie die geïnduceerd worden in een

systeem door bv. blikseminslag op een hoogspanningslijn.

De bestaande categorieën volgens EN 61010-1 zijn:

CAT I

Een CAT I-meter is geschikt voor metingen op beschermde

elektronische circuits die niet rechtstreeks verbonden zijn met het

lichtnet, bv. elektronische schakelingen, stuursignalen…

CAT

II

Een CAT II-meter is geschikt voor metingen in CAT I-omgevingen en

op enkelfasige apparaten die aan het lichtnet gekoppeld zijn door

middel van een stekker en circuits in een normale huiselijke

omgeving, op voorwaarde dat het circuit minstens 10 m verwijderd is

van een CAT III-omgeving, en minstens 20 m van een CAT IV-

omgeving. Bv. huishoudapparaten, draagbaar gereedschap...

CAT

III

Een CAT III-meter is geschikt voor metingen in CAT I- en CAT II-

omgevingen, alsook voor metingen aan enkel- en meerfasige (vaste)

toestellen op meer dan 10 m van een CAT IV-omgeving, en metingen

in of aan distributiekasten (zekeringkasten, verlichtingscircuits,

elektrisch fornuis).

Strona jest ładowana ...

Velleman DVM898 Instrukcja obsługi

Velleman DVM898 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty