Velleman DVM832 Instrukcja obsługi

DVM832

CAT. II 500 V / CAT. III 300 V

USER MANUAL 2

HANDLEIDING 17

MODE D'EMPLOI 32

MANUAL DEL USUARIO 48

BEDIENUNGSANLEITUNG 64

INSTRUKCJA OBSŁUGI 80

MANUAL DO UTILIZADOR 96

DVM832

V. 05 – 05/01/2022 2 ©Velleman Group nv

USER MANUAL

1. Introduction

To all residents of the European Union

Important environmental information about this

product

This symbol on the device or the package

indicates that disposal of the device after its

lifecycle could harm the environment. Do not

dispose of the unit (or batteries) as unsorted

municipal waste; it should be taken to a

specialized company for recycling. This device

should be returned to your distributor or to a local

recycling service. Respect the local environmental rules.

DVM832

V. 05 – 05/01/2022 3 ©Velleman Group nv

If in doubt, contact your local waste disposal

authorities.

Thank you for choosing Velleman! Please read the manual

thoroughly before bringing this device into service. If the

device was damaged in transit, do not install or use it and

contact your dealer.

2. Used Symbols

AC (Alternating Current)

DC (Direct Current)

Both AC and DC

Risk of Electric shock. A potentially hazardous

voltage is possible.

Caution: risk of danger, refer to the user

manual for safety information.

Warning: a hazardous condition or action that

may result in injury or death

Caution: condition or action that may result in

damage to the meter or equipment

under test

Double insulation (class 2-protection)

Earth

Fuse

Capacitor

Diode

Continuity

DVM832

V. 05 – 05/01/2022 4 ©Velleman Group nv

3. General Guidelines

Refer to the Velleman® Service and Quality Warranty

on the last pages of this manual.

This symbol indicates: Read instructions

Not reading the instructions and manual can lead

to damage, injury or death.

This symbol indicates: Danger

A hazardous condition or action that may result in

injury or death

This symbol indicates: Risk of

danger/damage

Risk of a hazardous condition or action that may

result in damage, injury or death

This symbol indicates: Attention; important

information

Ignoring this information can lead to hazardous

situations.

WARNING: To avoid electrical shock always

disconnect the test leads prior to opening the

housing. To prevent fire hazards, only use fuses

with the same ratings as specified in this manual.

Remark: refer to the warning on the battery

compartment

Avoid cold, heat and large temperature

fluctuations. When the unit is moved from a cold

to a warm location, leave it switched off until it

has reached room temperature. This to avoid

condensation and measuring errors.

Protect this device from shocks and abuse. Avoid

brute force when operating.

DVM832

V. 05 – 05/01/2022 5 ©Velleman Group nv

Pollution degree 2-device. For indoor use only.

Keep this device away from rain, moisture,

splashing and dripping liquids. Not for industrial

use. Refer to 8. Pollution degree.

Keep the device away from children and

unauthorised users.

Risk of electric shock during operation. Be

very careful when measuring live circuits.

There are no user-serviceable parts inside the

device.

Refer to an authorized dealer for service and/or

spare parts.

This is an installation category CAT III

measuring instrument. Never use this

equipment in a CAT IV environment. Never use

the meter with CAT II installations when

measuring voltages that might exceed the safety

margin of 500 V above earth ground. Never use

the meter with CAT III installations when

measuring voltages that might exceed the safety

margin of 300 V above earth ground. Refer to

7. Overvoltage/installation category.

Read this addendum and the manual thoroughly.

Familiarise yourself with the functions of the

device before actually using it.

All modifications of the device are forbidden for

safety reasons. Damage caused by user

modifications to the device is not covered by the

warranty.

Only use the device for its intended purpose.

Using the device in an unauthorized way will void

the warranty. Damage caused by disregard of

DVM832

V. 05 – 05/01/2022 6 ©Velleman Group nv

certain guidelines in this manual is not covered by

the warranty and the dealer will not accept

responsibility for any ensuing defects or

problems.

WARNING – To avoid electric shock, fire or

personal injury:

• Connect the common test lead before the live

test lead and remove the live test lead before

the common test lead.

• Disconnect the power and discharge all high-

voltage capacitors before you measure

resistance, continuity, capacitance or a diode

junction.

• When using the temperature probe, do not

connect the probe to live circuits.

4. Maintenance

There are no user-serviceable parts inside the

device.

Refer to an authorized dealer for service and/or

spare parts.

• Before performing any maintenance activities, disconnect

the test leads from the jacks.

• For instructions on replacing battery or fuse, refer to

15. Battery replacement.

• Do not apply abrasives or solvents to the meter. Use a

damp cloth and mild detergent for cleaning purposes.

5. During Use

Risk of electric shock during operation. Be

very careful when measuring live circuits.

DVM832

V. 05 – 05/01/2022 7 ©Velleman Group nv

• Never exceed the limit value for protection. This limit

value is listed separately in the specifications for each

range of measurement.

• Do not touch unused terminals when the meter is

linked to a circuit which is being tested.

• Set the range selector at its highest position if the

intensity of the charge to be measured is unknown

beforehand.

• Disconnect the test leads from the tested circuit before

rotating the range selector in order to change

functions.

• When carrying out measurements on a TV set or

switching power circuits, always remember that the

meter may be damaged by any high amplitude voltage

pulses at test points.

• Always be careful when working with voltages above

60 VDC or 30 VAC rms. Keep your fingers behind the probe

barriers at all times during measurement.

• Never perform resistance, diode or continuity

measurements on live circuits. Make sure all capacitors

in the circuit are depleted.

6. General Description

Refer to the illustration on page 2 of this manual:

1. Display (max. 1999 counts, max. 3 ½ digits,

dimensions: 47 x 15 mm)

With low-battery indication

2. Rotary switch for manual range selection

This switch is used to select functions and desired

ranges as well as to turn the meter on/off.

3. "VmA" jack

Insert the red (positive) test lead in this connector to

measure voltage, resistance and current (except

10 A).

4. "COM" jack

Insert the black (negative) test lead.

DVM832

V. 05 – 05/01/2022 8 ©Velleman Group nv

5. "10A" jack

Insert the red test lead in this connector in order to

measure a max. current of 10 A.

Test lead probe: CAT II 500 V/CAT III 300 V, 10 A, L

= 90 cm

7. Overvoltage/Installation Category

The applicable categories according EN 61010-1 are:

CAT

II

A CAT II-rated meter is suitable for measurements in

CAT I-environments and mono-phase appliances that

are connected to the mains by means of a plug and

circuits in a normal domestic environment, provided

that the circuit is at least 10m apart from a CAT III-

or 20 m apart from a CAT IV-environment. E.g.

household appliances, portable tools…

CAT

III

A CAT III-rated meter is suitable for measurements

in CAT I- and CAT II-environments, as well as for

measurements on (fixed) mono- or poly-phased

appliances which are at least 10 m apart from of a

CAT IV-environment, and for measurements in or on

distribution level equipment (fuse boxes, lighting

circuits, electric ovens).

8. Pollution Degree

IEC 61010-1 specifies different types of pollution

environments, for which different protective measures are

necessary to ensure safety. Harsher environments require

more protection, and the protection against the pollution

which is to be found in a certain environment depends

mainly on the insulation and the enclosure properties. The

pollution degree rating of the DVM indicates in which

environment the device may be used.

DVM832

V. 05 – 05/01/2022 9 ©Velleman Group nv

Pollution

degree 2

Only nonconductive pollution occurs.

Occasionally, temporary conductivity caused

by condensation is to be expected. (home and

office environments fall under this category)

•This device is only suitable for measurements

in Pollution degree class 2 environments.

9. Specifications

This device is not calibrated when purchased!

Regulations concerning environment of use:

Use this meter only for measurements in CAT I, CAT II and

CAT III environments (see §7)

Use this meter only in a pollution degree 2 environment

(see §8)

Ideal working conditions include:

temperature: 0 °C to 40 °C (32 °F to 104 °F)

relative humidity: max. 80 %

altitude: max. 2000 m (6560 ft)

voltage .........................................................500 V

fuse protection

F500 mA/600 V, 5 x 20 mm (not replaceable)

F10 A/600 V, 5 x 20 mm (not replaceable)

power supply ................ 2 x 1.5 VDC AAA/R03P (incl.)

display ......................................... LCD, 1999 counts

display dimensions ................................ 47 x 15 mm

over-range ....................................................... yes

continuity buzzer ............................................... yes

transistor test .................................................... no

diode test ......................................................... yes

low-battery indication ........................................ yes

ranging mode ............................................. manual

data hold .......................................................... no

backlight ........................................................... no

auto power-off ................................................... no

DVM832

V. 05 – 05/01/2022 10 ©Velleman Group nv

dimensions .................................. 118 x 65 x 30 mm

weight (with battery) ...................................... 100 g

operating environment:

temperature: 0 °C to 40 °C (32 to 104 °F)

humidity: < 80 % RH.

storage environment:

temperature: -20 °C to 60 °C (-4 °F to 140 °F)

humidity: < 90 % RH

test lead probe (incl.) CAT II 500 V/CAT II 300 V, 10 A;

L = 90 cm

9.1 DC VOLTAGE

Do not measure circuits that may contain

voltages > 500 V

range

resolution

accuracy

200 mV

0.1 mV

± (1.0 % rdg + 2 digits)

2000 mV

1 mV

20 V

10 mV

200 V

100 mV

500 V

1 V

± (1.2 % rdg + 2 digits)

Overload protection: 500 V DC or AC rms

Impedance: 1M Ω

9.2 AC VOLTAGE

Do not measure circuits that may contain

voltages > 500 V

range

resolution

accuracy

200 V

100 mV

± (1.2 % rdg + 3 digits)

500 V

1 V

Average sensing, calibrated to rms of sine wave

Frequency range: 40-500 Hz

Overload protection: 500 V DC or AC rms

Impedance: 450k Ω

DVM832

V. 05 – 05/01/2022 11 ©Velleman Group nv

9.3 DC CURRENT

Do not measure circuits that may contain

voltages > 500 V

range

resolution

accuracy

200 µA

0.1 µA

± (1.5 % rdg + 2 digits)

2000 µA

1 µA

20 mA

10 µA

200 mA

100 µA

± (2.0 % rdg + 2 digits)

10 A

10 mA

± (2.0 % rdg + 3 digits)

Overload protection: F0.5 A/600 V, F10 A/600 V fuse

Note: 10 A up to 10 seconds

9.4 RESISTANCE

Do not conduct resistance measurements

on live circuits

range

resolution

accuracy

200 Ω

0.1 Ω

± (1.0 % rdg + 5 digits)

2000 Ω

1 Ω

± (1.0 % rdg + 3 digits)

20k Ω

10 Ω

200k Ω

100 Ω

2000k Ω

1k Ω

± (1.5 % rdg + 3 digits)

Overload protection: F0.5 A/600 V fuse

DVM832

V. 05 – 05/01/2022 12 ©Velleman Group nv

9.5 DIODE AND CONTINUITY

Do not conduct diode or continuity

measurements on live circuits

range

description

test condition

display reads the

approximate

forward voltage of

the diode

forward DC current

± 10 µA

reversed DC

voltage ± 1.8 V

built-in buzzer

sounds if

resistance < 50 Ω

open-circuit

voltage ± 1.8 V

10. Voltage Measurement

Do not measure circuits that may contain voltages

> 500 V

Use extreme caution when measuring voltages

higher than 60 VDC or 30 VAC rms.

Always place your fingers behind the protective

edges of the test probes while measuring!

10.1 DC VOLTAGE MEASUREMENT

1. Connect the red test lead to the "VmA" jack and the

black lead to the "COM" jack.

2. Set the rotary switch in the desired V position. If

the voltage to be measured is unknown beforehand,

you should set the range switch in the highest range

position and then reduce gradually until the ideal

resolution is obtained.

DVM832

V. 05 – 05/01/2022 13 ©Velleman Group nv

3. Connect the test leads to the source being measured.

4. Read the voltage value on the LCD display along with

the polarity of the red lead connection.

10.2 AC VOLTAGE MEASUREMENT

1. Connect the red test lead to the "VmA" jack and the

black test lead to the "COM" jack.

2. Set the rotary switch in the appropriate V~ position.

3. Connect the test leads to the source to be measured.

4. Read the voltage value on the LCD display.

11. DC Current Measurement

Do not measure circuits that may contain voltages

> 500 V

Use extreme caution when measuring voltages

higher than 60 VDC.

Always place your fingers behind the protective

edges of the test probes while measuring!

1. Connect the red test lead to the "VmA" jack and the

black test lead to the "COM" jack (switch the red lead

to the "10A" jack for measurements between 200 mA

and 10 A).

2. Set the rotary switch (DCA) in the desired position.

3. Open the circuit in which the current is to be

measured and connect the test leads to the circuit IN

SERIES.

4. Read the current value and the polarity of the red

lead connection on the LCD display

12. Resistance Measurement

Do not conduct resistance measurements on live

circuits. Make sure all capacitors in the circuit are

depleted.

DVM832

V. 05 – 05/01/2022 14 ©Velleman Group nv

1. Connect the red test lead to the "VmA" jack and the

black test lead to the "COM" jack (the red lead has a

positive polarity "+").

2. Set the rotary switch in the appropriate "" range

position.

3. Connect the test leads to the resistor to be measured

and read the LCD display.

4. If the resistance being measured is connected to a

circuit, turn off the power and discharge all capacitors

before applying the test probes.

13. Diode Testing

Do not conduct diode or continuity measurements

on live circuits. Make sure all capacitors in the

circuit are depleted.

1. Connect the red test lead to "VmA" jack and the

black one to the "COM" jack (the red lead has a

positive polarity "+".).

2. Set the rotary switch in the " " position.

3. Connect the red test lead to the anode of the diode to

be tested and the black test lead to the cathode of

the diode. The approx. forward voltage drop of the

diode will be displayed. If the connection is reversed,

the display will merely show a "1".

14. Continuity Testing

Do not conduct diode or continuity measurements

on live circuits. Make sure all capacitors in the

circuit are depleted.

1. Connect the red test lead to "VmA" and the black

one to "COM".

2. Set the range switch in the " " position.

DVM832

V. 05 – 05/01/2022 15 ©Velleman Group nv

3. Connect the test leads to two points of the circuit to

be tested. If continuity exists, the built-in buzzer will

sound.

15. Battery Replacement

WARNING: To avoid electrical shock always

disconnect the test leads prior to opening the

housing. To prevent fire hazards, only use fuses

with the same ratings as specified in this manual.

Remark: refer to the warning on the battery

compartment

There are no user-serviceable parts inside the

device.

Refer to an authorized dealer for service and/or

spare parts.

Equipment must be isolated or disconnected from

the HAZARDOUS LIVE voltage before access

(referring to battery replacement by operator).

• When" " is displayed, the battery should be

replaced.

• Blown fuses almost always result from human error.

To replace the battery:

• Switch of the meter

• Release the screw located at the backside of the meter

and gently open the housing.

• Remove the old batteries and insert new ones.

Battery: 2 x 1.5 VDC AAA/R03P alkaline, do not use

rechargeable batteries and make sure to respect

the polarity

Make sure the meter is closed tight and put the protective

edge back in place before using the meter.

DVM832

V. 05 – 05/01/2022 16 ©Velleman Group nv

16. Troubleshooting

If the device beeps continuously while measuring

continuity, this means that the F500 mA/600 V internal

fuse is defective.

Keep in mind that a low battery level could lead to

incorrect measurements. Replace the batteries on a regular

basis.

Tip: the reduced luminosity of the backlight/LCD display

indicates a low battery level.

Use this device with original accessories only.

Velleman Group nv cannot be held responsible in the

event of damage or injury resulting from (incorrect)

use of this device. For more info concerning this

product and the latest version of this manual, please

visit our website www.velleman.eu. The information

in this manual is subject to change without prior

notice.

The copyright to this manual is owned by Velleman

Group nv. All worldwide rights reserved. No part of

this manual may be copied, reproduced, translated or

reduced to any electronic medium or otherwise without the

prior written consent of the copyright holder.

DVM832

HANDLEIDING

1. Inleiding

Aan alle ingezetenen van de Europese Unie

Belangrijke milieu-informatie betreffende dit product

Dit symbool op het toestel of de verpakking geeft aan dat,

als het na zijn levenscyclus wordt

weggeworpen, dit toestel schade kan

toebrengen aan het milieu. Gooi dit toestel (en

eventuele batterijen) niet bij het gewone

huishoudelijke afval; het moet bij een

gespecialiseerd bedrijf terechtkomen voor

recyclage. U moet dit toestel naar uw verdeler of naar een

lokaal recyclagepunt brengen. Respecteer de plaatselijke

milieuwetgeving.

Hebt u vragen, contacteer dan de plaatselijke

autoriteiten betreffende de verwijdering.

Dank u voor uw aankoop! Lees deze handleiding grondig

door voor u het toestel in gebruik neemt. Werd het toestel

beschadigd tijdens het transport, installeer het dan niet en

raadpleeg uw dealer.

2. Gebruikte symbolen

AC (wisselstroom)

DC (gelijkstroom)

Zowel wissel- als gelijkstroom

Elektrocutiegevaar. Een potentieel gevaarlijke

spanning kan aanwezig zijn.

DVM832

Opgelet: risico op gevaar, zie de

gebruikershandleiding voor

veiligheidsinformatie.

Waarschuwing: gevaarlijke toestand of actie

die kan leiden tot letsel of de dood

Opgelet: een toestand of actie die kan leiden

tot schade aan de meter of het toestel

onder test.

Dubbele isolatie (klasse II-bescherming)

Aarding

zekering

Capaciteit (condensator)

Diode

Continuïteit

3. Algemene richtlijnen

Raadpleeg de Velleman® service- en

kwaliteitsgarantie achteraan deze handleiding.

Dit symbool betekent: Instructies lezen

Het niet lezen van deze instructies en de

handleiding kan leiden tot beschadiging, letsel of

de dood.

Dit symbool betekent: Gevaar

Gevaarlijke toestand of actie die kan leiden tot

letsel of de dood

DVM832

Dit symbool betekent: Risico op

gevaar/schade

Risico op het ontstaan van een gevaarlijke

toestand of actie die kan leiden tot schade, letsel

of de dood

Dit symbool betekent: Opgelet; belangrijke

informatie

Het niet in acht nemen van deze informatie kan

leiden tot een gevaarlijke toestand.

WAARSCHUWING: om elektrische schokken te

vermijden, ontkoppel altijd de meetsnoeren

alvorens de behuizing te openen. Om brand te

voorkomen gebruik enkel zekeringen met

dezelfde specificaties zoals aangegeven in de

handleiding.

Opmerking: zie waarschuwing op de achterkant

van het toestel

Vermijd koude, hitte en grote

temperatuurschommelingen. Als het toestel van

een koude naar een warme omgeving verplaatst

wordt, laat het toestel dan eerst voldoende op

temperatuur komen. Dit om meetfouten en

condensvorming te vermijden.

Bescherm tegen schokken. Vermijd brute kracht

tijdens de bediening.

Vervuilingsgraad 2-toestel. Enkel geschikt voor

gebruik binnenshuis! Bescherm het toestel tegen

regen, vochtigheid en opspattende vloeistoffen.

Niet geschikt voor industrieel gebruik. Zie

8. Vervuilingsgraad.

DVM832

Houd dit toestel uit de buurt van kinderen en

onbevoegden.

Elektrocutiegevaar tijdens het gebruik van

deze multimeter. Wees voorzichtig tijdens het

meten van een circuit onder spanning.

Er zijn geen onderdelen in het toestel die door de

gebruiker gerepareerd kunnen worden.

Contacteer uw verdeler voor eventuele

reserveonderdelen.

Dit is een installatiecategorie CAT III-

meetinstrument. Gebruik dit toestel nooit in

een CAT IV-omgeving. Gebruik de meter nooit

voor CAT II-installaties bij spanningsmetingen die

de veiligheidsmarge van 500 V boven het

massapotentiaal (kunnen) overschrijden. Gebruik

de meter nooit voor CAT III-installaties bij

spanningsmetingen die de veiligheidsmarge van

300 V boven het massapotentiaal (kunnen)

overschrijden. Zie 7. Overspannings-

/installatiecategorie.

Lees deze bijlage en de handleiding grondig. Leer

eerst de functies van het toestel kennen voor u

het gaat gebruiken.

Om veiligheidsredenen mag u geen wijzigingen

aan het apparaat aanbrengen. Schade door

wijzigingen die de gebruiker heeft aangebracht

aan het toestel valt niet onder de garantie.

Gebruik het toestel enkel waarvoor het gemaakt

is. Bij onoordeelkundig gebruik vervalt de

garantie. De garantie geldt niet voor schade door

het negeren van bepaalde richtlijnen in deze

handleiding en uw dealer zal de

verantwoordelijkheid afwijzen voor defecten of

Strona jest ładowana ...

Velleman DVM832 Instrukcja obsługi

Velleman DVM832 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty