Anjielo Smart KW02_TuyaID Video doorbell manual Instrukcja obsługi

1

H.265 IP Video Doorbell

Multi-user

Record Unlock

Playback

Camera

Call

Night Vision

Full duplex

Motion Detect

POE

Full HD

2.4GHz WiFi

www.anjielo.com

2

COM NC NO

DC 12V

Press the "Reset" button

3seconds to reset

1 Function

IR CUT no color deviation, B/W night vision

Night vision

140 Horizontal angle

View angle

Push picture to APP when motion detection or call

Alarm message

Video recording after the call or motion detection

Playback

DC12V or power by connect 12V POE

Power adapter

Full duplex talk, Take photo, Take video, Unlock

Function

2 Speciﬁcation

88mm

145mm

23mm

39mm

Amazon echo, Google Home, Cloud storage

Third-Party Services

Photoresistor

IR Leds

Speaker

Mic

Rain cover

Camera

Call button

RJ45 port

Connect to 12V POE

Resolution

2Mega pixels

2.4G WiFi 802.11 b/g/n or wired network

Network

MicroSD card up to 256GB

External memory

Call button

Unlock by remote control, ID Card or APP

Unlock

Set ID card/ unlock delay time

www.anjielo.com

3

3 Parts List

Optional

The doorbell is installed at a height of 1.4~1.7 meters, try to avoid the

sunshine and rain, Using 2 screws or tape ﬁxed the doorbell on the wall,

wooden board, door, It can also be installed on the 86 box.

5 Installation diagram

1.4~1.7 Meter

3 Meters

140

Horizontal angle

°

4 System working diagram

Or

Smart Phone

Indoor chime

30Meters

4G

5G

15Meters 15Meters

<100Meters

Reset LAN1 LAN2 LAN3 LAN4 WAN

<30Meters

Router

86 Box

12V Power DC cable Screwdriver Screws and

anchors

Unlock wiring

TF card

Remote

control

Unlock

control

41 2 3 5

5* Blue User cards

1* Red Delete card

1* Yellow Add card

POE injector

Press and hold the ‘volume’ button until the

light stays on, then release,

Then keep pressing the doorbell's call pairing

until the indoor chime ring.

6 7

www.anjielo.com

48V POE

4

Option 1: Connect doorbell to WiFi and 12V power supply.

5

6

Option 2 (recommended):

The network cable is connected to a standard

12V POE switch, The length of the network cable is less than 100 meters.

Outdoor

6

Reset LAN1 LAN2 LAN3 LAN4 WAN

5

Use the drill bit to drill three holes. One

hole is large enough to pass through

the LAN cable,

use anchors if you install video doorbell on brick or concrete.

7

1. Remove the screws of the rain cover

2. The rain cover is separated from the doorbell

3. Insert the TF card

4. Fix the rain cover with two screws

5. Plug the DC cable into the power socket

6. Pass the DC cable through the hole on the wall

7. Plug the rain cover on the host and ﬁx the bottom screws.

8. Connect the 12V power supply to the female end of the DC cable

3

1

4

5. Connect the network cable to the network port of the doorbell

6. Plug the rain cover on the doorbell and ﬁx the bottom screws

7. Connect the doorbell via LAN Cable at RJ45 port to POE injector and into Router.

Diameter >1.5cm

Outdoor Outdoor Indoor

Outdoor

Indoor

Make sure that have a strong WiFi connection at the location of video doorbell.

Reset LAN1 LAN2 LAN3 LAN4 WAN

DC 12V

POE connect

www.anjielo.com

5

2. Wiring diagram of connect double power adapter.

Please check the speciﬁcation of electric current for existing electronic lock,

as the charger supplied is for a 12V power supply.

1. Wiring diagram of connect single power adapter

COM NC NO

6 Unlock settings

COM NC NO

3. Unlock controller wiring diagram (optional)

COM NC NO

Power on wiring diagram Power oﬀ wiring diagram

7 Device pairing

7.1 Pair indoor chime with smart doorbell

1. Long press the "volume" button of indoor chime until the light stays on,

then long press the "call" button of IP video doorbell to pair.

2. Clear the pairing

Press and hold the "Volume" button of indoor chime without connecting the

power supply, then connect the power supply until the light stays on.

Pair light Power on Power oﬀ

Delay time(Seconds)

Pair button

NC

COM

NO

-

12V

1S 4S 8S

NC

COM

NO

-

12V

NC

COM

NO

-

12V

Position

1S 4S

Delay time

8S 16S

www.anjielo.com

6

1. Search "Tuya Smart" or "Smart life"

from APP store or Google Play

according to phone system.

2. Scan the QR code to download.

9 App Download

7.2 Pair unlock control with smart doorbell

1. Press the "pair" button of the unlock control, the pair light will ﬂash once,

then press the "Unlock" icon on the app, the pairing light will continue to ﬂash.

2. Then press the "pair" button of the unlock control again, the light will stop

ﬂashing, then press the "Unlock" icon on the app again, the pairing light will

ﬂash several times. The pairing is successful.

3. Clear the pairing

Press the "pair" button on the unlock control for longer than 3 seconds until the

light on to the light oﬀ.

7.3 Pair remote control with unlock control

1. Press the "pair" button of the unlock control, the pair light will ﬂash one time,

then press the "unlock" button of the remote control, the pair light will ﬂash

continuously.

2. Then press the "pair" button of the unlock control again, the pair light stops

ﬂashing, then press the "unlock" button of the remote control again, the pair

light will ﬂash several times. The pairing is successful.

Default

o

Setting

8.2 Add users and remove users

8 RFID Card Settings

8.1 Setting the Management Card

Note that you cannot delete a user card if the card has not been added

or deleted already

.

Likewise you cannot add a user card,if the card has been added already

to another RFID access point

.

If you hear 3 beeps, then there is either an issue with the card or a mistake

in the operation

.

Turn the power to the doorbell oﬀ, by removing power and LAN cable if applicable,

and reset the switches to default (all 3 switches to oﬀ/bottom).Connect the doorbell

power on again.

Swipe yellow add card, and then light will illuminate and beep. Then swipe blue user

card to activate, then light will illuminate and beep to conﬁrm.

To remove the user, swipe the red delete card, followed by the applicable blue user card.

Troubleshooting:

The smart doorbell is supplied with 1x yellow add card,

1x red delete card and 5x blue user cards.

Ensure that the 3 switches are all set to oﬀ (bottom position).

Then turn oﬀ power of Smart doorbell by removing power and if applicable LAN

cable, and set the position 3 switch to ON and then turn power of doorbell on again.

You are now in management mode and the red and blue light will illuminate on

RFID front panel. Swipe the yellow add card and then the doorbell will beep to

conﬁrm. Then swipe the red delete card and the doorbell will beep and then

the light will go oﬀ.

www.anjielo.com

11 Add device to APP

7

10 Register & Login

1. Please register when using APP for the ﬁrst time.

2. After logging on the APP, please add devices after creating a family.

At the bottom right corner of the APP homepage, click "Me" ->

"Home Management" -> "Create a home", ﬁll in the information and

save it. the setter will become the family owner, you can set home

owner or common members.

3. After the home owner adds the device, the home members will add the

device automatically. After adding this doorbell, all home members

have unlock function than shared accounts.

You can add 20 administrators or home members.

4. The video doorbell is a device with a higher security level, the device

must be removed from the original account before it can be bound to

another account.

11.1 QR code and EZ Mode connection if doorbell connect to WiFi

Click "+" on the top right of the homepage.

4

1 2

1

2

3

Select "QR Code".

The blue light of the doorbell ﬂashes quickly, after checking, click "Next".

4

Select "Add Manually"->"Security & Video Surveillane" -> "Smart Doorbell".

www.anjielo.com

8

The doorbell only supports 2.4G WiFi, not 5G WiFi signal!

5

8

Select 2.4GHz WiFi, enter the WiFi password, and click "Next".

A QR code appears in the APP. Please scan the QR code from 15 to 20cm

away. After you hear the doorbell prompt, click "I Heard a Prompt".

7

5

6

8

7

Enter the "Adding device..." then "Scan devices." -> "Register on Cloud" ->

Initialize the device".

After the completion, it shows that the added successfully, you can modify

the device name, and click "Done" to ﬁnish the adding the device.

www.anjielo.com

9

11.2 Wired network connection

2 "Auto Scan"

1

Select "Cable". After checking, Click "Next" if the blue light of the doorbell

ﬂashes quickly.

Click "+" on the top right of the APP homepage.

2

3

4

3

6

After the completion, it shows that the addition is successful, you can modify the

device name, and click "Finish" to enter the video interface.

7

1 "Manually add" -> "Cable"

2

Select device to be added and click "Next"

3

4

Wait for the connection.

Select "Auto Scan".

2

3

Select "Add Manually"->"Security & Video Surveillane" -> "Smart Doorbell".

Wait for "Device found" -> "Register to Cloud" -> "Initializing device".

4

Waiting for connecting.

5

Select Device to Add.

5

45

Add successfully after click "Done".

5

www.anjielo.com

10

Click on the device to enter the liveing screen,

You can take photos, talk, video, unlock, playback(TF Card), and view albums.

1

2

3

4

5

6

7

8

9

10

11

12

Enter the mobile phone number or email address of the user you want to share,

click "Finish", the shared user cannot unlock.

9

11

12

After removing the device, the device will not be displayed on the device list

Modify icon, name, location of device.

12

4

5

6

3

Conﬁgure the device automation. Connect Amazon echo or Google Home.

1 Turn on/oﬀ the light of the doorbell button 2 The screen horizontal mirroring.

7

Motion detection on/oﬀ, set the alarm sensitivity and the alarm time period.

8

Check the capacity of the memory card, and format the memory card.

View IP address, ID, time zone.

Adjust the volume of the doorbell

The device will push the alarm information list to the APP after 30 minutes

10

Please check the common problems carefully.

12 View live video

Click the button in the upper right corner to

enter the setting interface.

Unlock: Unlock and save all records.

Message: Take photos and videos during

incoming calls or motion detection.

Cloud: The photos and videos stored in the cloud

server during incoming calls or motion

detection, do not worry about losing the

doorbell.

www.anjielo.com

11

1. After the visitor presses the call button, push notiﬁcations online

Tuya Smart 1m

Motion detected

IP Door has detected movement

You have a visitor

IP Door, someone is ringing the bell

Tuya Smart Now

Doorbell

13 Ring the bell and Motion Detected

2. The mobile phone standby state is pushed notiﬁcations as follows

2.1 Click the "Motion detected"

to enter the alarm message

2.2 Click the "

You have a visitor

"

to enter the living video.

Click the "Settings" icon in the upper

right corner to enter the

notiﬁcations push settings

www.anjielo.com

12

Users can click "Me" of hompage on the APP to enter "service and help".

1. "Voice third-party service", you can choose multiple smart product voice

control products, each third party, the third-party service have detailed

connection tutorials.

2. "Home Management" can create a home or join a home and set permissions

3. "Message Center" can view alarm information

4. If you are not familiar with the app or device, pls check "Help and Feedback".

15 Help and service

14 Multi-Video Preview

If the APP is connected to more than

1 video device. Multiple devices can

be viewed at the same time.

www.anjielo.com

Anjielo Smart KW02_TuyaID Video doorbell manual Instrukcja obsługi

Anjielo Smart KW02_TuyaID Video doorbell manual Instrukcja obsługi

w innych językach

Powiązane artykuły

Inne dokumenty