Aleph AS-100 Instrukcja obsługi

Marka
Aleph
Model
AS-100
Typ
Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

Only using the AS-100TX information
for the certification
User Manual
7.NOTES
USER MANUAL
Wireless Transmission Module
AS-100
Thank you for selecting ALEPH product.
efore operating the product.Please read the manual carefully b
8. Caution
C6 Building 301A Heng Feng Industrial City, He Zhou, Xi Xiang
Street ,Bao An Qu, Shenzhen,
China.
Tel. : +86-755 - 3321 0588 Fax.: +86-755-3321 0600
E-mail: [email protected] Http : // www . ain-cn.com
4700 Aircenter Circle,Reno Nevada,89502 USA
Tel. : +1-775-827-8000 Fax.: +1-775-827-8044
E-mail: [email protected] Http : // www.aleph-usa.com
1.The product shall be installed indoor and do not use it under the following conditions.
① In the place where it is likely to be exposed to dust, high humidity,high temperatures,or rain.
② In the place where it is closed to magnetic field.
③ In the place where vibration or shock is directly transmitted to the product.
2.In order to ensure the normal operation of the product
① Please power off before cleaning the product.
② Do not use chemical detergents to clean the product.
3.Never disassemble, repair and modify the product.
4.The product comply with the FCC Standard and requirements of RoHS.
5. Specifications and design are subject to change without prior notice.
AI NEXT LLC
AIN TECHNOLOGY(SHENZHEN)CO.,LTD
TROUBLE TROUBLE CAUSE
REMEDY
Apply proper input voltage
Change the direction of the battery
Replace new batteries
Battery direction reversed
No or low input power
Unit does not power up
No voltage of battery
6.TROUBLE SHOOTING AND MAINTENANCE
No signal
No wireless signal
The wire to the “V-” power input was discon-
nected, the “V+” is still connected.
Disconnect wire from the “ + “ power input.
Correct wiring polarity
Signal line connection reverse
Transmitter alarm LED
does not light
Receiver alarm LED
does not light
•
Micro-based signal activates
• Compatible with various wired detectors
The AS-100 is a digital receiver with an isolated relay output for use with transmitters, The receiver
can be used in a variety of remote control applications. When the receiver detects signal from a
transmitter, the relay output activates.
• Transmitter and Receiver Relay kit
•
Compact and consumes very little power
•
Get rid of wire, keep your house clean and safe
•
Easy installation, with adhesive pad or screws
AS-100TX AS-100RX
1.
2.
3.
4.
1
2 3 4
1
2
1.SPECIFICATIONS
4.INSTALLATION
Install the cover and
lock the screws
5.CONNECTION MODE
Two batteries into the
Transmitter
Open the lower cover
mounting hole and
lock the screw
B
R
W
P
W
V+
_
V
N.O.
COM
N.C.
+
-
N.C. OR N.O.
LOOP
ALARM
AUX.
POWER
ALARM PANEL
Power Supply
Transmitter
V
A
AA LR03
Receiver
12 - 24V DC
Temperature
- 20 ℃ ~+60 ℃
Working Frequency
433.92 MHz
Wireless Distance
≥ 100m
(Open field)
Transmitter Input
Dual N.O. ( Contact without power)
Receiver Relay Output
N.C./ N.O. DC 24V ,2A Max.
Battery Life
3 Years (Normal Mode)
Using Environments
Indoor
Dimension
2.5"Hx1.2"Wx0.7"D(65. 0x31. 0x18.5 mm)
Product Certificates
FCC CE ROHS
2.DIMENSIONS
*Specifications and design are subject to
without prior notice.
change
Loosen the bottom sc-
rew and remove the
upper cover
N. O. SIGNAL
R B
+
+
-
-
Receiver
R B W P W
AL AR M
PO WER
IN PU R
V+ V- N.O
COM
N.C
2.5
0.7
1.2
UNIT:inch(mm)
(65.0)
(31. 0)
(18. 5)
AIR Sensor
PIR Sensor
Door Magnetic
Pressure
Sensor Mat
*
Can connect two groups detector
3.SYSTEM PARING
ALARM PANEL CONNECTION
B
R
W
P
W
V+
_
V
N.O.
COM
N.C.
+
-
POWER
SUPPLY
DVR
SECURITY CAMERA CONNECTION
B
R
W
P
W
V+
_
V
N.O.
COM
N.C.
PRDIO
POWER
XFMA
STRIKE
XFMR
SPWER
DOOR STRIKE CONNECTION EXTERNAL RELAY CONNECTION
LOAD
EXTERNAL
RELAY
B
R
W
P
W
V+
_
V
N.O.
COM
N.C.
PRDIO
POWER
XFMA
To paring the receiver to the transmitter, required
to trigger the detector(connected with transm-
itter) in 5 seconds when receiver power on, the
Receiver's LED will flash 6 times when paring
successes.
Every Receiver can only paring one Transmitter,
the previous Transmitter will invalid automatically
when Receiver is success to paring with new one
NOTE:
Detector
Detector
12
2.5
11
2
x
FCC Caution:
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Aleph AS-100 Instrukcja obsługi

Marka
Aleph
Model
AS-100
Typ
Instrukcja obsługi
Ten podręcznik jest również odpowiedni dla
ściągnij PDF
raport

w innych językach

Inne dokumenty