Panasonic SDRH280 Instrukcja obsługi

Operating Instructions

Instrukcja obsługi

SD Card/Hard Disk

Video Camera

Model No.SDR-H280

Before use, please read these instructions

completely.

Przed pierwszym włączeniem kamery prosimy o

dokładne przeczytanie instrukcji obsługi.

LSQT1361 B

EP

LSQT1361_EP(ENG).book 1 ページ２００８年３月１４日　金曜日　午後３時４４分

2

LSQT1361

Information for Your Safety

∫ EMC Electric and magnetic

compatibility

This symbol (CE) is located on the rating plate.

Use only the recommended accessories.

≥ Do not use any other AV/S cables and USB

cables except the supplied one.

≥ When you use the cable which are sold

separately, please make sure to use the one

whose length is less than 3 meters.

WARNING:

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR PRODUCT

DAMAGE,

≥ DO NOT EXPOSE THIS APPARATUS TO

RAIN, MOISTURE, DRIPPING OR

SPLASHING AND THAT NO OBJECTS

FILLED WITH LIQUIDS, SUCH AS VASES,

SHALL BE PLACED ON THE

APPARATUS.

≥ USE ONLY THE RECOMMENDED

ACCESSORIES.

≥ DO NOT REMOVE THE COVER (OR

BACK); THERE ARE NO USER

SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

CAUTION!

≥ DO NOT INSTALL OR PLACE THIS UNIT

IN A BOOKCASE, BUILT-IN CABINET OR

IN ANOTHER CONFINED SPACE.

ENSURE THE UNIT IS WELL

VENTILATED. TO PREVENT RISK OF

ELECTRIC SHOCK OR FIRE HAZARD

DUE TO OVERHEATING, ENSURE THAT

CURTAINS AND ANY OTHER

MATERIALS DO NOT OBSTRUCT THE

VENTILATION VENTS.

≥ DO NOT OBSTRUCT THE UNIT’S

VENTILATION OPENINGS WITH

NEWSPAPERS, TABLECLOTHS,

CURTAINS, AND SIMILAR ITEMS.

≥ DO NOT PLACE SOURCES OF NAKED

FLAMES, SUCH AS LIGHTED CANDLES,

ON THE UNIT.

≥ DISPOSE OF BATTERIES IN AN

ENVIRONMENTALLY FRIENDLY

MANNER.

The socket outlet shall be installed near the

equipment and easily accessible.

The mains plug of the power supply cord shall

remain readily operable.

To completely disconnect this apparatus from

the AC Mains, disconnect the power supply

cord plug from AC receptacle.

Product Identification Marking is located on

the bottom of units.

Warning

Risk of fire, explosion and burns. Do not

disassemble.

Do not heat the batteries above the following

temperatures or incinerate.

Button-type battery 60 oC

Battery pack 60 oC

LSQT1361_EP(ENG).book 2 ページ２００８年３月１４日　金曜日　午後３時４４分

3

LSQT1361

∫ Indemnity concerning recording

content

The manufacturer shall in no event be liable for the

loss of recordings due to malfunction or defect of

this unit, its accessories or recordable media.

∫ Carefully observe copyright laws

Recording of pre-recorded tapes or discs or other

published or broadcast material for purposes other

than your own private use may infringe copyright

laws. Even for the purpose of private use,

recording of certain material may be restricted.

≥ SDHC Logo is a trademark.

≥

U.S. Patent Nos. 6,836,549; 6,381,747;

7,050,698; 6,516,132; and 5,583,936.

This product incorporates copyright protection

technology that is protected by U.S. patents and

other intellectual property rights. Use of this

copyright protection technology must be

authorized by Macrovision, and is intended for

home and other limited viewing uses only unless

otherwise authorized by Macrovision. Reverse

engineering or disassembly is prohibited.

≥ Manufactured under license from Dolby

Laboratories.

Dolby and the double-D symbol are

trademarks of Dolby Laboratories.

≥ LEICA is a registered trademark of Leica

Microsystems IR GmbH and DICOMAR is a

registered trademark of Leica Camera AG.

≥

Microsoft

®

, Windows

®

, Windows Vista

®

,

DirectDraw

®

, DirectSound

®

, DirectX

®

, and Internet

Explorer

®

are either registered trademarks or

trademarks of the Microsoft Corporation in the

United States and/or other countries.

≥ Microsoft product screen shot(s) reprinted with

permission from Microsoft Corporation.

≥ IBM, PC/AT and PowerPC are registered

trademarks of International Business Machines

Corporation of the U.S.

≥

Intel

®

, Core

™

and Pentium

®

are the registered

trademarks or trademarks of the Intel Corporation

in the United States and other countries.

≥ Macintosh and Mac OS are either registered

trademarks or trademarks of Apple Inc. in the

United States and/or other countries.

≥

Other names of systems and products mentioned

in these instructions are usually the registered

trademarks or trademarks of the manufacturers

who developed the system or product concerned.

Information on Disposal for Users of Waste

Electrical & Electronic Equipment (private

households)

This symbol on the products

and/or accompanying

documents means that used

electrical and electronic

products should not be mixed

with general household waste.

For proper treatment, recovery

and recycling, please take

these products to designated collection points,

where they will be accepted on a free of

charge basis. Alternatively, in some countries

you may be able to return your products to

your local retailer upon the purchase of an

equivalent new product.

Disposing of this product correctly will help to

save valuable resources and prevent any

potential negative effects on human health

and the environment which could otherwise

arise from inappropriate waste handling.

Please contact your local authority for further

details of your nearest designated collection

point.

Penalties may be applicable for incorrect

disposal of this waste, in accordance with

national legislation.

For business users in the European Union

If you wish to discard electrical and electronic

equipment, please contact your dealer or

supplier for further information.

Information on Disposal in other Countries

outside the European Union

This symbol is only valid in the European

Union.

If you wish to discard this product, please

contact your local authorities or dealer and

ask for the correct method of disposal.

ENGLISH

LSQT1361_EP(ENG).book 3 ページ２００８年３月１４日　金曜日　午後３時４４分

4

LSQT1361

Information for Your Safety...................2

Before using

Features ..................................................6

Accessories............................................8

Parts identification and handling .........8

Using the LCD monitor .............................10

Using the remote control ..........................11

HDD and SD card .................................13

Concerning the internal HDD and

cards that can be used on this unit...........13

Concerning SD cards ...............................13

HDD handling precautions .......................15

Access lamp.............................................15

Setup

Power supply........................................17

Charging the battery.................................17

Connecting to the AC outlet .....................19

Turning the unit on/off...............................19

Inserting/removing an SD card...........20

Selecting a mode..................................21

How to use the joystick .......................21

Switching the language.......................25

Using the menu screen........................25

Setting date and time...........................27

Adjusting the LCD monitor .................28

Recording

Before recording ..................................30

Recording motion pictures .................32

Recording modes and recordable time

available for the motion picture ................34

Recording still pictures .......................35

Number of pixels and picture quality for still

picture recording.......................................38

Various recording functions ...............39

Zoom in/out function.................................39

Recording yourself ...................................40

Recording with the video light ..................40

Backlight compensation function..............41

Fade in/fade out function..........................41

Soft skin mode..........................................42

Tele macro function.................................. 43

Colour night view function........................ 43

Self-timer recording.................................. 44

Recording guideline function.................... 44

Wide mode............................................... 45

Image stabilizer function .......................... 45

Wind noise reduction function.................. 45

Manual recording functions................46

Scene mode............................................. 46

Manual focus adjustment ......................... 47

White balance .......................................... 47

Manual shutter speed/aperture

adjustment ............................................... 49

Playback

Motion picture playback......................51

Still picture playback ...........................55

Editing

Editing scenes......................................57

Deleting scenes ....................................... 57

Locking motion picture scenes................. 58

Using playlists......................................59

What is a playlist?.................................... 59

Creating a new playlist............................. 59

Playing back a playlist.............................. 60

Editing a playlist....................................... 60

Editing still pictures.............................62

Deleting still picture files .......................... 62

Locking still picture files ........................... 63

DPOF setting ........................................... 64

Copying still picture files .......................... 65

HDD and card management

HDD management ................................66

Formatting HDD....................................... 66

Displaying HDD information..................... 66

Card management................................67

Formatting an SD card............................. 67

Contents

LSQT1361_EP(ENG).book 4 ページ２００８年３月１４日　金曜日　午後３時４４分

5

LSQT1361

With other products

With a TV...............................................68

Playback on TV ........................................68

With a DVD recorder ............................69

Dubbing recordings onto

a DVD recorder ............................................69

With a VCR............................................69

Dubbing images onto

other video devices ......................................69

With a printer (PictBridge)...................70

With a PC

Before using with a PC........................73

What you can do with a PC......................73

Operating environment.............................74

End User License Agreement ..................76

Installation ............................................77

Installing VideoCam Suite ........................77

Uninstalling the software ..........................78

Connection and recognition ...............79

Connection and recognition procedures...79

About the PC display................................79

To disconnect USB cable safely ...............80

Using VideoCam Suite.........................81

Reading the operating instructions of the

software....................................................81

DVD COPY function.................................82

If using a Macintosh.............................83

Others

Menus....................................................84

Menu list ...................................................84

Other menus.............................................85

Indications ............................................87

Indications ................................................87

Messages .................................................89

Functions that cannot be used

simultaneously .....................................91

Frequently asked questions................92

Troubleshooting...................................94

Cautions for use...................................99

Explanation of terms..........................102

Specifications.....................................104

Number of recordable pictures on

the HDD or an SD card ..........................107

LSQT1361_EP(ENG).book 5 ページ２００８年３月１４日　金曜日　午後３時４４分

Before using

6

LSQT1361

Before using

Features

∫ Extended recording!

You can record the equivalent of approximately twenty-two 8 cm DVD discs on the 30 GB internal HDD.

You can also record motion pictures and still pictures on an SD card.

∫ Easy recording! (l 32)

No need to search for the recording start position.

The new recording will not overwrite any previously recorded scene.

∫ Easy playback! (l 51)

Recorded scenes are displayed as thumbnails.

You can easily search for the scenes you want to watch.

HDD

HDDHDD

LSQT1361_EP(ENG).book 6 ページ２００８年３月１４日　金曜日　午後３時４４分

Before using

7

LSQT1361

∫ Editing scenes! (l 57, 59)

You can create an original video (playlist) by collecting together your favourite scenes recorded on the

HDD.

∫ Using with a computer! (l 73)

If you use the supplied software, you can create a backup DVD of the scenes recorded on this unit with

just one button.

You can also make an original DVD-Video by exporting the scenes to a computer and then editing

them.

LSQT1361_EP(ENG).book 7 ページ２００８年３月１４日　金曜日　午後３時４４分

8

LSQT1361

Before using

Accessories

Check the accessories before using this unit.

Some optional accessories may not be available

in some countries.

* The shoe adaptor VW-SK12E (optional) is

necessary.

Parts identification and

handling

1 Lens (LEICA DICOMAR)

≥ Do not attach a conversion lens or a filter

to this unit as it will cause vignetting.

2 Lens cover

3 Video light (l 40)

4 White balance sensor (l 48)

Remote control sensor (l 12)

5 Microphone (built-in, stereo)

6 Terminal cover

7 Menu button [MENU] (l 25)

Battery pack

CGA-DU12

AC adaptor

VSK0651B (DE-974GC)

DC cable

K2GJ2DC00015 or

K2GJ2DC00011

AV/S cable

K2KZ9CB00001

AC cable

K2CR2DA00004

Remote control

N2QAEC000023

Button-type battery

CR2025

USB cable

K1HA05CD0019 or

K1HA05CD0016

CD-ROM

Optional accessories

AC adaptor (VW-AD11E)

Battery pack (lithium/CGA-DU12/1150 mAh)

Battery pack (lithium/CGA-DU14/1360 mAh)

Battery pack (lithium/CGA-DU21/2040 mAh)

Shoe adaptor (VW-SK12E)

Video DC light (VW-LDC102E)

*

Light bulb for video DC light (VZ-LL10E)

Tripod (VW-CT45E)

3

4

5

2

1

11

12

14

13

15

1

6

18

6

7

8

9

10

1

7

19

LSQT1361_EP(ENG).book 8 ページ２００８年３月１４日　金曜日　午後３時４４分

9

LSQT1361

Before using

8 DC input terminal [DC/C.C. IN] (l 19)

9 LCD monitor open part (l 10)

10 Battery holder (l 17)

11 Audio-video output terminal [A/V]

(l 68, 69)

12 Status indicator (l 19)

13 Power switch [OFF/ON] (l 19)

14 HDD/computer access lamp [ACCESS/

PC] (l 15, 79)

15 Mode dial (l 21)

16 Joystick (l 21)

17 Delete button [ ] (l 57, 61, 62)

18 USB terminal [ ] (l 70, 79)

19 Recording start/stop button (l 32)

20 Lens cover open/close ring (l 10)

21 When recording: Zoom lever [W/T] (l 39)

When playing back: Volume lever

[sVOLr] (l 53)

22 Photoshot button [ ] (l 35)

23 Illumination LED (l 86)

24 Card slot (l 20)

25 Tripod receptacle (l 10)

26 Battery release lever [BATTERY] (l 17)

27 LCD monitor (l 10)

28 Card slot open lever (l 20)

29 DVD COPY button [DVD COPY] (l 82)

30 Speaker

31 Power LCD plus button

[POWER LCD PLUS] (l 29)

32 Video light button [LIGHT] (l 40)

33 Reset button [RESET] (l 97)

34 Mode select switch [AUTO/MANUAL/

FOCUS] (l 31, 46, 47)

35 Card slot cover [SD CARD] (l 20)

36 Card access lamp [ACCESS] (l 16, 79)

37 Grip belt (l 10)

21 22

23

20

25

26

24

Due to limitations in LCD production

technology, there may be some tiny bright

or dark spots on the LCD monitor screen.

However, this is not a malfunction and

does not affect the recorded picture.

27

29 30

31

36

35

33

32

28

34

37

LSQT1361_EP(ENG).book 9 ページ２００８年３月１４日　金曜日　午後３時４４分

10

LSQT1361

Before using

Adjust the belt length so it fits your hand.

Adjust the belt length and the pad

position.

1 Flip the belt.

2 Adjust the length.

3 Replace the belt.

For the lens protection, be sure to close the lens

cover when not in use.

Rotate the lens cover open/close

ring.

This is a hole for attaching the unit to the optional

tripod.

(Please carefully read the operating instructions

for how to attach the unit to the tripod.)

≥ When the tripod is used, the card slot cover

cannot be opened. Insert an SD card before

attaching this unit to the tripod. (l 20)

You can record the image while viewing it on the

LCD monitor.

1 Place your finger on the LCD

monitor open part A and pull the

LCD monitor out in the direction

of the arrow.

≥ It can open up to 90o.

2 Adjust the angle of the LCD

monitor as desired.

≥ It can rotate up to 180o A towards the lens or

90o B towards the opposite direction.

Using grip belt

Using the lens cover

Tripod receptacle

3

1

2

Using the LCD monitor

A

AB

LSQT1361_EP(ENG).book 10 ページ２００８年３月１４日　金曜日　午後３時４４分

11

LSQT1361

Before using

≥ The brightness and colour level of the LCD

monitor can be adjusted from the menu.

(l 28)

≥ The unit may be damaged or fail if the LCD

monitor is forcibly opened or rotated.

1 Photoshot button [PHOTO SHOT, ]*

2 On-screen display button [EXT DISPLAY]

(l 69)

3 Date/time button [DATE/TIME] (l 27)

4 Playback operation buttons (l 52)

5 Delete button [ ]*

6 Direction buttons [3,4,2,1] (l 26)

7 Recording start/stop button [START/

STOP]*

8 Zoom/volume buttons [ZOOM, VOL]*

9 Menu button [MENU]* (l 26)

10 Enter button [ENTER] (l 26)

* means that these buttons function in the same

manner as the corresponding buttons on the

unit.

∫ Install a button-type battery

Install the supplied button-type battery in the

remote control before using it.

1 While pressing the stopper A,

pull out the battery holder.

2 Set the button-type battery with

its (r) mark facing upward and

then put the battery holder back

in place.

∫ Concerning the button-type battery

≥ When the button-type battery runs down,

replace it with a new battery (part number:

CR2025). The battery should normally last

about 1 year, however this depends on how

frequently the unit is used.

≥ Keep the button-type battery out of the reach of

children.

Using the remote control

ZOOM

START/

STOP

PHOTO

SHOT

EXT

DISPLAY

DATE/

TIME

VOL

PLAY

STOPSKIP SKIP

MENU

ENTER

PAU SE

SEARCH

STILL ADV STILL ADV

SEARCH

1

2

3

4

6

7

8

9

1

0

5

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replace only with the same or

equivalent type recommended by the

manufacturer. Dispose of used batteries

according to the manufacturer’s instructions.

Warning

Keep the Button-Type battery out of the reach

of children. Never put Button-Type battery in

mouth. If swallowed call your doctor.

A

LSQT1361_EP(ENG).book 11 ページ２００８年３月１４日　金曜日　午後３時４４分

12

LSQT1361

Before using

∫ Remote control usable range

The distance between the remote control and the

unit’s remote control sensor A: Within approx.

5m

Angle: Approx. 10o up and 15o down, left, and

right

≥ The remote control is intended for indoor

operation. Outdoors or under strong light, the

unit may not operate properly even within the

usable ranges.

AA

LSQT1361_EP(ENG).book 12 ページ２００８年３月１４日　金曜日　午後３時４４分

Before using

13

LSQT1361

HDD and SD card

This unit can be used for recording motion pictures and still pictures to the internal HDD and an SD

card.

*1 The 30 GB hard drive utilizes a portion of the storage space for formatting, file management and

other purposes. 30 GB is 30,000,000,000 bytes. Usable capacity will be less.

*2 Cannot be guaranteed in operation.

≥ For the purposes of these operating instructions, SD Memory Card and SDHC Memory Card are

referred to as the “SD card”.

≥ This unit supports SD Memory Cards formatted in FAT12 system and FAT16 system based on SD

Memory Card Specifications and SDHC Memory Cards formatted in FAT32 system.

Concerning the internal HDD and cards that can be used on

this unit

Internal HDD

(Hard Disk

Drive)

SD Memory Card

SDHC

Memory

Card

Display on the

screen

Indication in these

instructions

[HDD] [SD]

Capacity 30 GB

*1

8MB/

16 MB

32 MB/

64 MB/

128 MB

256 MB/

512 MB/

1GB/2GB

4GB

Functions

Recording motion

pictures

¥ – ¥

*2

¥

Recording still

pictures

¥¥

Creating playlists ¥ –

¥: available –: not available

Concerning SD cards

This unit is compatible with both SD Memory cards and SDHC Memory cards. You can only use

SDHC Memory cards on devices that are compatible with them. You cannot use SDHC Memory

cards on devices that are only compatible with SD Memory cards. (When using an SDHC Memory

card on another device, be sure to read the operating instructions for that device.)

LSQT1361_EP(ENG).book 13 ページ２００８年３月１４日　金曜日　午後３時４４分

Before using

14

LSQT1361

≥ Use this unit to format SD cards. If an SD card is formatted on other products (such as a computer),

the time spent for recording may become longer and you may not be able to use the SD card. (l 67)

≥ When using an SD card on which data has been written many times, the remaining time left for

recording may be reduced.

≥ Keep the Memory Card out of reach of children to prevent swallowing.

≥ A MultiMediaCard cannot be used on this unit.

≥ When the write-protect switch A on SD card is locked, no recording, deletion or

editing will be possible on the card.

∫ About SD cards that you can use for motion picture recording

We recommend using SD cards conforming to Class 2 or higher of the SD Speed Class Rating or the

following SD cards made by Panasonic for motion picture recording. (If another kind of SD card is used,

the recording may suddenly stop during motion picture recording.)

≥ Operation in motion picture recording is not guaranteed with the following SD cards.

jSD cards from 32 MB to 128 MB

jSD cards from 256 MB to 4 GB other than the ones mentioned above

≥ Please confirm the latest information on the following website. (This website is in English only.)

http://panasonic.jp/support/global/cs/e_cam

∫ Handling precautions

≥ Do not touch the terminals on the back of the card.

≥ Do not expose the terminals of the card to water, garbage or dust.

≥ Do not place the card in the following areas:

jIn direct sunlight.

jIn very dusty or humid areas.

jNear a heater.

jLocations susceptible to significant difference in temperature (condensation can occur).

jWhere static electricity or electromagnetic waves occur.

≥ Put the card back in its bag or case for protection when not using it.

≥ Electrical noise, static electricity or failure of this unit or the SD card may damage or erase the data

stored on the SD card. We recommend saving important data on a computer.

High Speed SD

Memory Card

Class 2 SD/SDHC

Memory Card

Class 4 SD/SDHC

Memory Card

Class 6 SD/SDHC

Memory Card

256 MB RP-SDH256 RP-SDR256 – –

512 MB RP-SDK512 RP-SDR512 – –

1GB RP-SDH01G RP-SDR01G – RP-SDV01G

2GB RP-SDK02G RP-SDR02G RP-SDM02G RP-SDV02G

4GB – RP-SDR04G RP-SDM04G RP-SDV04G

A

LSQT1361_EP(ENG).book 14 ページ２００８年３月１４日　金曜日　午後３時４４分

Before using

15

LSQT1361

This unit has an internal HDD. The HDD is a precision instrument so take care when handling it.

∫ Do not cause any vibrations or impacts to this unit.

The HDD may no longer be recognised or recording or playback may no longer be possible. In

particular, do not cause any vibrations or impacts during recording or playback.

∫ Do not drop this unit.

The HDD may be damaged if this unit receives a strong impact due it to being dropped etc.

This unit has a drop detection function to protect the HDD from impact if this unit is dropped. If it detects

that this unit has been dropped during motion picture recording, the HDD protection operation sound

may be recorded. Also if it detects that the unit is being continuously dropped, recording or playback

may stop.

∫ Take note of the temperature of this unit.

It may no longer be possible to record or playback if the temperature of this unit is too high or low. A

warning message will appear on this unit’s LCD monitor if an irregularity in the temperature is detected.

(l 89)

∫ Do not use the unit in a low pressure area.

The HDD may be damaged if you use this unit where the altitude is more than 3000 m.

∫ Back up important recorded data to protect it.

Save recorded data periodically on a computer, DVD disc, etc. for backup purposes.

If the HDD fails, the recorded data cannot be repaired.

∫ ACCESS/PC lamp

≥ When this unit accesses the HDD (reading, recording, playback,

erasing, etc.), the ACCESS/PC lamp lights up.

≥ If the following operations are performed when the ACCESS/PC

lamp is lit, then the HDD or the recorded data may be damaged or

this unit may malfunction.

sCausing strong vibrations or impacts to this unit

sOperating the OFF/ON switch or the mode dial

sRemoving the battery or disconnecting the AC adaptor

HDD handling precautions

∫ Indemnity concerning recorded content

Panasonic does not accept any responsibility for damages directly or indirectly due to any type of

problems that result in loss of recording or edited content, and does not guarantee any content if

recording or editing does not work properly. Likewise, the above also applies in a case where any

type of repair is made to the unit (including any other non-HDD related component).

Access lamp

LSQT1361_EP(ENG).book 15 ページ２００８年３月１４日　金曜日　午後３時４４分

Before using

16

LSQT1361

∫ Card access lamp

≥ When this unit accesses the SD card (reading, recording, playback,

erasing, etc.), the access lamp lights up.

≥ If the following operations are performed when the access lamp is lit, then

the SD card or the recorded data may be damaged or this unit may

malfunction.

sOpening the card slot cover

sRemoving the SD card

sOperating the OFF/ON switch or the mode dial

sRemoving the battery or disconnecting the AC adaptor

LSQT1361_EP(ENG).book 16 ページ２００８年３月１４日　金曜日　午後３時４４分

17

LSQT1361

Setup

Power supply

When this unit is purchased, the battery is not

charged. Charge the battery before using this unit.

≥ If the DC cable is connected to the AC

adaptor, then the battery will not be

charged. Remove the DC cable from the AC

adaptor.

1 Connect the AC cable to the AC

adaptor and the AC outlet.

2 Put the battery on the battery

mount by aligning the mark, and

then securely plug it in.

≥ The output plug of the AC cable is not

completely connected to the AC adaptor

socket. As shown in A, there is a gap.

∫ Charging lamp

≥ Battery charging time (l 18)

≥

We recommend using Panasonic batteries. (

l

8)

≥ If you use other batteries, we cannot guarantee

the quality of this product.

Push the battery against the battery

holder and slide it until it clicks.

While sliding the BATTERY lever,

slide the battery to remove it.

≥

Hold the battery with your hand so it does not fall.

≥ Before removing the battery, be sure to set the

OFF/ON switch to OFF and check that the

status indicator is off.

It has been found that counterfeit battery

packs which look very similar to the genuine

product are made available to purchase in

some markets. Some of these battery packs

are not adequately protected with internal

protection to meet the requirements of

appropriate safety standards. There is a

possibility that these battery packs may lead

to fire or explosion. Please be advised that we

are not liable for any accident or failure

occurring as a result of use of a counterfeit

battery pack. To ensure that safe products are

used we would recommend that a genuine

Panasonic battery pack is used.

≥

Be aware that many batteries sold at

extremely cheap prices or in situations where

it is difficult to verify the actual products before

purchase have proven to be counterfeit.

Charging the battery

A

Lights up: Charging

Goes off: Charging completed

Flashing:

The battery is over discharged

(discharged excessively). In a while,

the lamp will light up and normal

charging will start.

When the battery temperature is

excessively high or low, the CHARGE

lamp flashes and the charging time will

be longer than normal.

Inserting the battery

Removing the battery

LSQT1361_EP(ENG).book 17 ページ２００８年３月１４日　金曜日　午後３時４４分

18

LSQT1361

Setup

≥ Do not heat or expose to flame.

≥ Do not leave a battery pack in an automobile

exposed to direct sunlight for a long period of

time with doors and windows closed.

Notice about the rechargeable battery

The battery is designated recyclable.

Please follow your local recycling regulations.

The times shown in the tables below are for when the temperature is 25 oC and the humidity is 60%. If

the temperature is higher or lower than 25 oC, the charging time will become longer.

∫ Charging time

≥ The charging time shown in the table are approximations.

≥ “2 h 25 min” indicates 2 hours 25 minutes.

∫ Recordable time

≥ The actual recordable time refers to the recordable time when repeatedly starting/stopping recording,

turning the unit on/off, moving the zoom lever, etc.

≥ “2 h 5 min” indicates 2 hours 5 minutes.

≥ The display changes as the battery capacity reduces.

####.

If the battery discharges, then ( ) will flash.

≥ The recordable times will vary depending on the status of use. These times are approximations. The

recordable time will become shorter when you use this unit with the LCD monitor lit up by pressing

the POWER LCD PLUS button.

≥

The batteries heat up after use or charging. This unit will also heat up while being used. This is not a malfunction.

≥ Be aware that the operating time of the battery will become shorter in low temperatures. We

recommend charging a spare battery for use when recording.

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replace only with the same or

equivalent type recommended by the

manufacturer. Dispose of used batteries

according to the manufacturer’s instructions.

Charging time and recordable time

Battery model number Voltage/capacity Charging time

Supplied battery/

CGA-DU12 (optional)

7.2 V/1150 mAh 2 h 25 min

CGA-DU14 (optional) 7.2 V/1360 mAh 2 h 45 min

CGA-DU21 (optional) 7.2 V/2040 mAh 3 h 55 min

Battery model

number

Voltage/capacity

Recording

destination

Maximum

continuously

recordable time

Actual recordable

time

Supplied battery/

CGA-DU12

(optional)

7.2 V/1150 mAh

[HDD] 2h5min 55min

[SD] 2h20min 1h

CGA-DU14

(optional)

7.2 V/1360 mAh

[HDD] 2h30min 1h5min

[SD] 2h45min 1h15min

CGA-DU21

(optional)

7.2 V/2040 mAh

[HDD] 3h45min 1h40min

[SD] 4h10min 1h50min

LSQT1361_EP(ENG).book 18 ページ２００８年３月１４日　金曜日　午後３時４４分

19

LSQT1361

Setup

The unit is in the standby condition when the AC

adaptor is connected. The primary circuit is

always “live” as long as the AC adaptor is

connected to an electrical outlet.

1 Connect the AC cable to the AC

adaptor and the AC outlet.

2 Connect the DC cable to the AC

adaptor.

3 Connect the DC cable to this unit.

≥ Do not use the AC cable with any other

equipment as it is designed only for this unit.

Do not use the AC cable from other equipment

with this unit.

≥ While the DC cable is connected to the AC

adaptor, the battery will not be charged.

≥ When recording, open the lens cover before

turning the unit on. (l 10) If the unit is turned

on with the lens cover closed, the automatic

white balance adjustment (l 102) may not

function properly.

Set the OFF/ON switch to ON.

The status indicator A lights and the power turns

on.

≥ When the unit is turned on for the first time, a

message asking you to set the date and time

will appear. Select [YES] and set the date and

time. (l 27)

≥ When the unit is turned on for the first time, a

selection screen will appear to select the

recording destination for motion pictures and

still pictures.

Select [HDD] or [SD CARD] for each type of

picture and then press the joystick.

Set the OFF/ON switch to OFF.

The status indicator A goes off when the power

turns off.

When the OFF/ON switch is set to ON, the power

can be turned on and off with the LCD monitor

when the unit is in video recording mode or

picture recording mode.

Connecting to the AC outlet

Turning the unit on/off

How to turn on the power

How to turn off the power

How to turn the power on and off

with the LCD monitor

A

LSQT1361_EP(ENG).book 19 ページ２００８年３月１４日　金曜日　午後３時４４分

20

LSQT1361

Setup

∫ To turn on the power

Open the LCD monitor.

The status indicator lights and the power turns

on.

∫ To turn off the power

Close the LCD monitor.

The status indicator goes off and the power turns

off.

≥ The power will not turn off while recording even

if the LCD monitor is closed.

Inserting/removing an SD

card

Before inserting/removing an SD card, be

sure to set the OFF/ON switch to OFF.

1 Set the OFF/ON switch to OFF to

turn off the power.

≥ Check that the status indicator has gone off.

2 Open the LCD monitor and then

slide the card slot open lever A

to open the card slot cover.

3 Insert/remove the SD card into/

from the card slot.

≥ When inserting an SD card, face the label side

B upwards and press it straight in as far as it

goes.

≥ When removing the SD card, press the centre

of the SD card and then pull it straight out.

Set the OFF/ON switch to OFF when the unit

is not being used.

If the SD card is inserted or removed while the

OFF/ON switch is set to ON, this unit may

malfunction or the data recorded on the SD

card may be lost.

A

B

LSQT1361_EP(ENG).book 20 ページ２００８年３月１４日　金曜日　午後３時４４分

Strona jest ładowana ...

Panasonic SDRH280 Instrukcja obsługi

Panasonic SDRH280 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty