Classic Exhibits GK-1004 Setup Instructions
- Typ
- Setup Instructions
© 2023
Order #XXXXX
Top View
Perspective View
10’
10’
GK-1004 - 10’x10’ Display
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS
© 2023
Order #XXXXX General Information
Assembly Assembly Cont’d
Side-by-Side Assembly
1) Frames: Place frames side-by-side with one higher than the
other, then slide panel down to lock panels securely together.
2) Corner Connectors: Repeat Step 1 for installing corner
connectors to frames.
Side-by-Side Disassembly
1) Pull pin lock outwards to disengage.
2) Pull frames upward and apart at the same time to detatch.
Push pin lock into hole of connecting frame.
Note: Block on pin lock will secure in groove.
Pin Lock
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
Graphic Removal
SEG Graphic Installation
Corner A
Corner D
Corner B
Corner C
It is important to first insert graphic
into each alternate corner, then to
the sides of the frame.
If this is not done, graphic will not fit
into the frame correctly.
Step 1
Insert corner A.
Turn edge of graphic so silicon welt
is perpendicular to face of graphic.
Insert narrow side of welt with fabric
to outside into the channel.
Repeat for other side of this corner.
Step 2
Repeat Step 1 for opposite corner
C, then insert corner B, followed by
corner D, to complete the
installation of the corners.
Step 3
Once all corners are inserted, press
one silicon edge into channel from
corners and work toward the center.
Make sure welt is fully inserted into
channel. Continue until all sides are
done. Smooth out edges of graphic.
To remove the graphic from
the frame, locate the fabric
pull tab.
Gently pull up on the tab to
remove the fabric.
© 2023
Step 1 of 2
Order #XXXXX
1
6
3
2
78
11
12
10
9
45
Item
1
2
3
4
5
6
7
8
9
10
11
12
Qty.
1
1
1
1
1
1
1
1
1
1
1
1
Description
14.125””w x 95”h Gravitee Panel
95”h Gravitee Post w/Caps
23””w x 95”h Gravitee Panel
28.5””w x 95”h Gravitee Panel
95”h Gravitee Post
38””w x 95”h Gravitee Panel w/ Door
95”h Gravitee Post w/Caps
28.5””w x 95”h Gravitee Panel
28.5””w x 95”h Gravitee Panel
95”h Gravitee Post w/Caps
38””w x 95”h Gravitee Panel
95”h Gravitee Post
Steps:
1) Assemble panels and connectors in numerical order.
See Gravitee Panel Assembly sheet for instruction.
Completed Assembly
Top View
w/Caps
Top View
Top View
Top View
w/Caps
Top View
w/Caps
Backwall Assembly
© 2023
Step 2 of 2
Order #XXXXX
Steps:
1) Install SEG graphics to front of assembly. See
General Information sheet for SEG Graphic Installation.
2) Connect lights to top of panels, where desired.
See Light Connection detail.
Completed Assembly
Graphic wraps
around corner.
Graphic wraps
around corner.
*
Slide light onto clip then lock clip
into groove of horizontal extrusion.
Light Connection
Clip
Light
Light
Clip
Horizontal Extrusion
**
Backwall Attachments
-
1
-
2
-
3
-
4
Classic Exhibits GK-1004 Setup Instructions
- Typ
- Setup Instructions
w innych językach
- English: Classic Exhibits GK-1004
Powiązane dokumenty
-
Classic Exhibits GK-2004 Setup Instructions
-
-
-
-
-
-
-
-
-