AMP Research 75132-01A Instrukcja instalacji

AMP Research
Marka
AMP Research
Model
75132-01A
Typ
Instrukcja instalacji
www.amp-research.com 1/15 IM75132 rev 10.26.22
INSTALLATION GUIDE
3-5 Hours
Professional installation recommended
TOOLS REQUIRED
qSafety goggles
qMeasuring tape
q10 mm socket
q13 mm socket
q1/2” socket
qRatchet wrench and extension
qWire crimpers
qWire stripper / cutter
q 3/16” hex key wrench (allen wrench)
q4mm hex key wrench ( allen wrench )
qElectrical tape
qWeather proof caulking (silicone sealer)
qSilicone spray
qDrill
qDrill bit 3/16”
INSTALLATION TIME
12 3 4
SKILL LEVEL
4= Experienced
AMP RESEARCH TECH SUPPORT 1-888-983-2204 (Press 2)
Monday - Friday, 7:00 AM - 5:00 PM PST
APPLICATION MODEL YEAR AMP Part #
Jeep Wrangler JL 4Dr 2018- 2023 75132-01A
(For Gas, Diesel and 4XE models)
(Also includes Rubicon 392)
5-Year Limited Warranty
WARRANTY
Invented, engineered and manufactured exclusively by AMP Research in the USA.
May be covered by one OR MORE of the following patents:
6,641,158; 6,830,257; 6,834,875; 6,938,909; 7,055,839; 7,380,807; 7,413,204; 7,398,985; 7,584,975; 7,566,064; 7,487,986; 8,157,277;
8,408,571; 9,302,626; 9,561,751; 10,053,017; CA2463717
©2012 AMP Research. All rights reserved. Printed in USA.
www.amp-research.com 2/15 IM75132 rev 10.26.22
AMP RESEARCH POWERSTEPTM – Jeep Wrangler JL
CAUTION: HANDLE WITH CARE.
To ensure our customers receive all components with full integrity, we pack the motors separate from their linkage
assemblies. This requires that the installer position and fasten the motor before continuing with the install. Please
follow the instructions below and handle the assembly carefully.
CAUTION: Dropping the assembly or any excessive impact MAY cause damage to the motor.
Instructions:
1. Position the gear cover in place as shown if not already in place.
2. Seat motor into position on the three mounting bosses. This may require an adjustment of the gear by moving
the swing arms.
3. After seating into place, fasten the motor with the three motor mount screws with 4mm Hex Head. Tighten
screws to 36 in-lbs (4N-m). Do not over torque.
EXPLODED VIEW
• Motor
• Hex Head Bolt
www.amp-research.com 3/15 IM75132 rev 10.26.22
AMP RESEARCH POWERSTEPTM – Jeep Wrangler JL
1x2
Step assembly
End cap left (x1)
End cap right (x1)
T-nut insert (x2)
Socket cap screw (x2)
Nut plate (x2)
3
Motor Linkage assembly
(passenger side)
4
Idler Linkage assembly
x2
2
Motor Linkage
assembly (driver side)
Wire harness
5
Controller STA
7
Tube (Installation
Tool)
6
www.amp-research.com 4/15 IM75132 rev 10.26.22
AMP RESEARCH POWERSTEPTM – Jeep Wrangler JL
Socket Cap
Screw
15 x8
Cable tie (11”)
20 x2
Cable tie (7”)
19
x20
14
M8 Button
Head Bolt
x8
21
Butt Connector
x8
12
Rear LED
Light Bracket
x2
Shim Spacer
18 x2
17 x8
Washer
16 x4
M8 Hex Bolt w
Conical washer
24
Motor Cover
x2
22
CRH Motor
x2 23
Cinch Fastener
x6 25
M8 Head Hex Bolt
x4
13
Front LED
Light Bracket
x2
11
LED Lamp
x4
8
OBD Module
9
OBD Module extension
10
Posi-Lock®
x2
www.amp-research.com 5/15 IM75132 rev 10.26.22
AMP RESEARCH POWERSTEPTM – Jeep Wrangler JL
14
17
16
Install Rear Idler Linkage:
Locate rear most mounting hole
set. Using supplied button head
screws(14) and washers(17)
assemble linkage to pinch
weld. Before tightening, slide
Light mounting bracket(12) in
forward mounting hole. Next use
supplied hex bolt with conical
washer(17) through bottom
threaded insert in body. Leave
bolts loose. Repeat linkage
installation for passenger side.
12
Note: When installing the light bracket, the nut plate insert with the raised portion faces the bolt.
2
Rear linkage
mounting location
Front linkage
mounting location
Mounting positions circled for front and rear linkage mounting points. Passenger side
shown.
Note: Motors face forward on each side.
Passenger Side shown.
1
www.amp-research.com 6/15 IM75132 rev 10.26.22
AMP RESEARCH POWERSTEPTM – Jeep Wrangler JL
Slide motor assembly onto drive shaft and mounting
bosses of driving linkage assembly. Use supplied M8
bolts(25). Torque to 8 ft-lbs(11N-m).
Torque button head screws from
step 1 and 2 to 16ft lbs (22N-m).
Then, torque hex bolts from step 1
and 2 to 16ft lbs (22N-m).
56
Install Front Drive Linkage: Locate next
set of mounting holes forward. Note drive
linkage with motor mount facing towards
front of vehicle. Using supplied button head
screws(14) and washers(17) assemble
linkage to pinch weld. Before tightening,
slide Light mounting bracket(13) in forward
mounting hole. Next use supplied hex bolt
with conical washer(16) and shim (18)
through bottom threaded insert in body. Leave
bolts loose. Repeat linkage installation on
passenger side.
Mount step extrusion to linkage assemblies. Line up T-nuts in step assembly with slots in lower
mounts of linkage assemblies. Fasten loosely to allow for adjustments. Line up step extrusion
with rear fender well. Tighten and torque 4 socket cap screws(15) with 3/16” allen wrench.
Torque to 10 ft-lbs. (13.5N-m)
Note: When installing the light bracket, the nut plate insert with the raised portion faces the bolt.
3
415 15
www.amp-research.com 7/15 IM75132 rev 10.26.22
AMP RESEARCH POWERSTEPTM – Jeep Wrangler JL
Remove fuse from Power
Step Wire Harness.
GAS MODELS ONLY: Remove fuse from Power Step Wire Harness. Prepare large tie-wraps
(20) for mounting Power Step Controller (5). Loosely loop tie-wraps around large bundle of
wires behind battery in engine compartment. Insert controller into tie-wrap loops and cinch down
securely. The tie-wraps should cinch down into channels on controller surface. Connect power
leads from Controller, Red to positive battery terminal and Black to the vehicle body ground as
shown.
Gas Models ONLY follow steps 7 and 8 then go to step 13.
Includes Rubicon 392 models.
Diesel models go to step 9.
4XE models go to step 11.
GAS MODELS ONLY: Route the two Wire Harness legs down over the wheel wells toward Motor
Linkages, long leg across to the driver side. Secure harness with tie wraps (19).
7
1
8
www.amp-research.com 8/15 IM75132 rev 10.26.22
AMP RESEARCH POWERSTEPTM – Jeep Wrangler JL
Diesel models ONLY follow steps 9 and 10 then go to step 13.
Remove fuse from Power
Step Wire Harness.
DIESEL MODELS ONLY: Remove fuse from Power
Step Wire Harness. Prepare large tie-wraps(20) for
mounting Power Step Controller (5). Loosely loop
tie-wraps (19) around large bundle of wires behind
battery in engine compartment. Insert controller into
tie-wrap loops and cinch down securely. The tie-
wraps should cinch down into channels on controller
surface. Connect power leads from Controller, Red to
positive battery terminal and Black to the vehicle body
ground as shown.
9
DIESEL MODELS ONLY: Route longer harness Leg across to driver side . Secure harness to cowl
with tie wraps (19) to keep harness away from hot engine components. Next route harness under
Coolant recovery tank then down and to the outside of the frame rails. Route shorter harness leg
down the passenger side ensuring the harness is run to the outside of the frame rails and away
from any hot exhaust components. Secure harness with tie wraps (19).
10
www.amp-research.com 9/15 IM75132 rev 10.26.22
AMP RESEARCH POWERSTEPTM – Jeep Wrangler JL
Remove fuse from Power
Step Wire Harness.
4XE MODELS ONLY: Remove fuse from Power Step Wire Harness. Prepare large tie-wraps
(20) for mounting Power Step Controller (5). Loosely loop tie-wraps around large bundle of
wires behind battery in engine compartment. Insert controller into tie-wrap loops and cinch down
securely. The tie-wraps should cinch down into channels on controller surface. Connect power
leads from Controller, Red to positive battery terminal and Black to the vehicle body ground as
shown.
4XE Models ONLY follow steps 11 and 12 then proceed to step 13.
11
4XE MODELS ONLY: Route longer harness Leg across to driver side. Secure harness to cowl
with tie wraps (19) to keep harness away from hot engine components. Next route harness under
Coolant recovery tank then down and to the outside of the frame rails. Route shorter harness leg
down the passenger side ensuring the harness is run to the outside of the frame rails and away
from any hot exhaust components. Secure harness with tie wraps (19).
1
12
www.amp-research.com 10/15 IM75132 rev 10.26.22
AMP RESEARCH POWERSTEPTM – Jeep Wrangler JL
Press and release glove box safety tab to fully open and remove glove box, next, release
glox box dampener located on the left side.
Glove box safety tab
Locate white block (on right side) and plug the 2 pin connector from the OBD module extension
(8) into that port.
Carefully leave glove box hanging to expose plugs behind it.
1
14
1
13
1
15
www.amp-research.com 11/15 IM75132 rev 10.26.22
AMP RESEARCH POWERSTEPTM – Jeep Wrangler JL
Pull back carpet on passenger side on the top side of middle console and then use provided
Tube (7) to route OBD II Extension (9) behind middle console. Tape open end of extension to the
tube and push the tube through middle console.
From driver side, pull tube (7) that was pushed
through from passenger side.
Remove OBD II Extension (9) from tube (7)
and plug wire to OBD module (8) wire.
1
17
16
18
www.amp-research.com 12/15 IM75132 rev 10.26.22
AMP RESEARCH POWERSTEPTM – Jeep Wrangler JL
Route trigger wires through rewall. Locate round plastic plug on rewall to the left of the brake
assembly. Drill small hole using a 3/16 drill bit. Route trigger wires through rewall. Use supplied
posi-lock® (10) to connect wires to OBD Module (8).
Apply silicone to seal o rewall.
Use cable ties to secure all
wires in place. Plug in OBD
Module.
5
20
19
www.amp-research.com 13/15 IM75132 rev 10.26.22
AMP RESEARCH POWERSTEPTM – Jeep Wrangler JL
Vehicle Port
Powerstep
Connection Module
Direct to Port Option
Powerstep
Control Module
To Vehicle
Power (12V)
To Powerstep
Motors
Powerstep
Control Module
To Vehicle
Power (12V)
To Powerstep
Motors
Powerstep
Connection Module
Vehicle Port
Pass-Through Harness Option
Vehicle Port
Pass-Through Harness
(pin-topin at each terminal)
New Vehicle Port
(replaces original port)
OBD II Connector located
below steering column.
OBD II install: Use Supplied Posi-Lock® connectors to attach the Plug and Play Module to the
Harness. Attach matching colors on the harness to the wires on the module. Plug in module to
OBD II port on the vehicle. Secure harness with supplied tie wraps.
Note: If the OBD II pass thru harness (76404-01A) was purchased see install sheet supplied in packaging. The
pass through harness allows for an open port for other accessories. See below for a brief description.
1
21
www.amp-research.com 14/15 IM75132 rev 10.26.22
AMP RESEARCH POWERSTEPTM – Jeep Wrangler JL
Using supplied butt connectors (21), connect the lamp
wires. Red to Red, Black to Black. Once Crimped use
heat gun to shrink tube. Close and wrap conduit with
electrical tape. Secure all loose wires with cable ties. Pull
lamp wires upward to avoid any wire snagging.
Reinstall Fuse from Powerstep Wire
Harness.
Ax LED lamp (11) to LED Bracket (12 & 13) (brackets previously installed in step 2 and 3).
1
5
19
18
On driver side, run Wire Harness leg down and along underside of the vehicle oor and frame
to front Drive Linkage. Connect harness to motor and secure harness with tie wraps. Route
remainder of wire harness towards rear linkage assembly for LED lights. Repeat step on
passenger side.
1
20
22 24
6
24
23
21
6
www.amp-research.com 15/15 IM75132 rev 10.26.22
AMP RESEARCH POWERSTEPTM – Jeep Wrangler JL
CORRECT OPERATION OF LIGHTS: All four lamps will illuminate upon opening any door of vehicle.
Lamps will stay on until restowing of both Power Steps or until 5 minutes has expired with the doors open.
When the lights timeout after 5 minutes, they can be reillumintated by closing and opening any door of
vehicle.
FINAL SYSTEM CHECK
Check that all doors activate the PowerStep and the LED lights work when doors open and close.
NORMAL OPERATION: When the doors open, PowerStep automatically deploys from under the vehicle.
When the doors are closed, PowerStep will automatically return to the stowed/retracted position. Note that
there is a 2-second delay before the PowerStep returns to the stowed/retracted position.
Check that all doors activate the Power Step and the LED Lights work when doors open and
close. Reinstall any remaining trim panels.
37
22
™
Thank you for your recent AMP Research Purchase.
REGISTER YOUR PRODUCT TODAY FOR
FASTER SERVICE & PRODUCT UPDATES
Please visit:
www.amp-research.com/productregistration
or scan the QR Code
Product Registration Benefits:
• Ensure we have your purchase receipt and product info in our
system which is required for warranty
• Faster and easier access to customer service and tech support in
the unlikely event you need warranty or product support
• Registration helps us keep you up to date on product information
and offers
To view other Amp Research products that may be offered for your vehicle.
Please visit: www.amp-research.com
AMERICAN DESIGNED, ENGINEERED AND MANUFACTURED.
Rev 01.05.21
Automatic power deploy:
The running boards will extend down and out when the doors are opened.
Automatic power stow:
The running boards will return to the stowed position when the doors are closed. There will be a 2-second
delay before the running boards move to the stowed position.
Automatic stop:
If an object is in the way of the moving running board, the running board will automatically stop.
To reset, clear any obstruction, then simply open and close the door to resume normal operation.
Manually set in the deployed (OUT) position for access to the roof:
your foot while at the same time closing the door. To resume normal operation, open and close the door.
Maintenance: In adverse conditions, debris such as mud, dirt, and salt may become trapped in the running
board mechanism, possibly leading to unwanted noise. If this occurs, manually set the running boards to
Avoid spraying the motors directly. After washing, apply silicone spray lubricant to the hinge pivot pins.
Do not apply silicone, wax or protectants like Armor All® to the running board stepping surface.
Caution! Keep hands away when the running board is in motion.
™
Congratulations on your purchase of the
genuine AMP Research PowerStep!
Here’s what you should know...
AMP RESEARCH warrants this product to be free from defects in material and workmanship for FIVE (5) YEARS FROM
DATE OF PURCHASE, provided there has been normal use and proper maintenance. This warranty applies to the original
purchaser only. All remedies under this warranty are limited to the repair replacement of the product itself, or the repair
or replacement of any component part thereof, found by the factory to be defective within the time period specied. The
decision to repair or replace is wholly within the discretion of the manufacturer.
for instructions. You must retain proof of purchase and submit a copy with any items returned for warranty work. Upon
completion of warranty work, if any, we will return the repaired or replaced item or items to you freight prepaid. Damage
to our products caused by accidents, re, vandalism, negligence, misinstallation, misuse, Acts of God, or by defective parts
not manufactured by us, is not covered under this warranty.
ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE CREATED HEREBY ARE
LIMITED IN DURATION TO THE SAME DURATION AND SCOPE AS THE EXPRESS WRITTEN WARRANTY. OUR COMPANY SHALL
NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGE.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specic
legal rights, and you may also have other rights that vary from state to state.
FOR WARRANTY ISSUES WITH THIS PRODUCT PLEASE CALL AMP RESEARCH TECH SUPPORT 1-888-983-2204
5-YEAR LIMITED WARRANTY
WARNING
Be sure to read and precisely follow the provided instructions when installing this product. Failure to do so could place the vehicle
occupants in a potentially dangerous situation. After installing or reinstalling, re-check to insure that the product is properly installed.
AMP Research PowerStep running boards automatically move
when the doors are opened to assist entering and exiting the vehicle.
The material that your product is made from can be recycled.
Please also consider recycling the packaging that your
product came in.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

AMP Research 75132-01A Instrukcja instalacji

AMP Research
Marka
AMP Research
Model
75132-01A
Typ
Instrukcja instalacji
ściągnij PDF
raport

w innych językach

Powiązane dokumenty

Inne dokumenty