Unbranded 72171-189-L Instrukcja obsługi

Unbranded
Marka
Unbranded
Model
72171-189-L
Typ
Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

INSTALLATION INSTRUCTIONS
For Model # 72171/72172/72173/72178-189-L
READ AND SAVE THESE INSTRUCTIONS
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARING FOR INSTALLATION (Fig. 1)
1. Shut off power at the circuit breaker and remove the old fixture,
including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts on a clear
area. Take care not to lose any parts necessary for installation.
3. Unscrew the cap nuts (L) and the rubber washers (K), and separate
the mounting plate (C) (part #:A-020) from back plate (N), then attach
the mounting plate(C) to the outlet box(not provided) with the two
screws(E) (Size:8-32*1/2”).
Note: the side of mounting plate marked “GND” must face out.
4. Adjust the two mounting screws (D) on mounting plate (C) spaced the
same distance apart as the holes on back plate(N). Secure mounting
screws (D) into mounting plate (C) with the hex nuts provided. Note:
The length of mounting screws (D) into mounting plate (C) may be
adjusted if necessary.
5. Align the curved end of scroll arm (J) through the decorative ring (R),
secure the other end to the back plate (N) with screw (F) and hex
nut(I), gasket (H) and rubber washers (G).
CONNECTION THE WIRES (Fig. 2)
6. Connect the electrical wires as shown in (Fig.2), making sure that all
wire connectors (B) are secured. If your outlet has a ground wire
(green or bare copper), connect the fixture ground wire to it.
Otherwise, connect the fixture ground wire directly to the mounting
plate using the green screw provided.
FINISHING THE INSTALLATION (Fig.1)
7. Align back plate (N) onto mounting plate (C) and secure with the
rubber washers (K) and cap nuts (L).
8. Separate lamp body (P) from top cover (M) by unscrewing the
mounting screws (Q). Align the glass (O) into body (P) and secure with
glass clips (S).
9. Re-attach body (P) to the top cover (M) with mounting screws (Q).
10. To prevent moisture from entering the outlet box and causing a short,
use clear caulking (i.e. Indoor/Outdoor Silicone Sealant) to outline the
outside off fixture back-plate where it meets the wall leaving a space at
bottom to allow moisture a means to escape (Fig 3).
11. Bulb information: (1 x AC LED 13W included.)
DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS
DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
Replacing LED module (Fig. 4)
The LED module can be replaced by a qualified electrician and shut off the
power at the circuit breaker and remove fixture from the outlet box without
cutting of wire and without damage to any decorative element to which the
fixture is attached. See installation steps for more details (Fig 4.)
a. Remove the aluminum sheet (X) by loosening screws (Y). Carefully
disconnect the wire covers.
b. Remove the module cover (R), loosen the screw (Z) to disassemble
the module (W), washer (V), aluminum sheet (X), gasket (U), nut (T).
c. Carefully remove the LED module (W), reverse steps a-b for installing
the new LED module (W). Note: The LED module should be provided
by a specified supplier.
d. For better heat dissipation the LED module (W) should be installed
with the heat transfer silicone when re-lamping
Your installation is now complete. Return power to the outlet box
and test the fixture.
Fig.3
Fig.1
IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A QUALIFIED
ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION.
Part# A-020
Mounting plate (1)
Ground screw (1)
Mounting screws (2)
Fig 4
  • Page 1 1

Unbranded 72171-189-L Instrukcja obsługi

Unbranded
Marka
Unbranded
Model
72171-189-L
Typ
Instrukcja obsługi
Niniejsza instrukcja jest również odpowiednia dla
Pobierz PDF
raport

w innych językach

Inne dokumenty