Dometic SmartStart RV Instrukcja obsługi

CLIMATE CONTROL

ACCESSORIES

Form No. 4445103956 2023-06-21

This product can expose you to chemicals including

lead and di(2-ethylhexyl)phthalate, which are known

to the State of California to cause cancer, birth

defects or other reproductive harm.

WARNING

For more information, go to

www.P65Warnings.ca.gov

RUN

Design Protected

RUN

FAULT LED

Item# 9610002970

120VAC

SmartStart SMRTSTACRV

EN RV So Start Accessory

Installation and Operating Manual ...........3

2EN

RV So Start Accessory

Copyright

The underlying technical design and the products contained herein may be protected by design, patent or be patent

pending. The trademarks mentioned in this manual belong to Dometic Sweden AB. All rights are reserved.

RV So Start Accessory Contents

1 Related documents ...................... 3

2 Explanation of symbols and safety

instructions ............................ 3

2.1 Recognize safety information .............3

2.2 Understand signal words ................4

2.3 Supplemental directives .................4

2.4 General safety messages .................4

3 Intended use ........................... 5

4 General information ..................... 5

4.1 Tools and materials .....................5

4.2 Compatibility ..........................5

4.3 Component locations ...................6

4.4 Model identification ...................10

4.5 Data plate ............................10

5 Specifications ......................... 10

6 Wiring diagrams ....................... 10

7 Preinstallation ......................... 13

7.1 Bracket configuration ..................13

7.2 Bracket assembly ......................14

7.3 Attaching the hose clamp ...............15

8 Installation ............................ 16

8.1 Installing the device - Brisk II .............17

8.2 Installing the device - Penguin II ..........22

8.3 Installing the device -Blizzard NXT ........26

8.4 Installing the device - FreshJet 3 Series

Mechanical ..........................31

9 Operation .............................39

10 Troubleshooting .......................39

11 Disposal ..............................40

Limited 1-year warranty ....................40

Service center & dealer locations

Visit: www.dometic.com

Please read these instructions carefully and follow all instructions,

guidelines, and warnings included in this product manual in order to

ensure that you install, use, and maintain the product properly at all

times. These instructions MUST stay with this product.

By using the product, you hereby conﬁrm that you have read

all instructions, guidelines, and warnings carefully and that you

understand and agree to abide by the terms and conditions as set

forth herein. You agree to use this product only for the intended

purpose and application and in accordance with the instructions,

guidelines, and warnings as set forth in this product manual as well

as in accordance with all applicable laws and regulations. A failure

to read and follow the instructions and warnings set forth herein may

result in an injury to yourself and others, damage to your product,

or damage to other property in the vicinity. This product manual,

including the instructions, guidelines, and warnings, and related

documentation, may be subject to changes and updates. For up-to-

date product information, please visit www.dometic.com.

3

EN

Contents

1 Related documents

Find the installation and operation

manual on-line in French at

http://documents.dometic.com/

?object_id=86747

Find the installation and operation

manual on-line in Spanish at

http://documents.dometic.com/

?object_id=86748

2 Explanation of symbols and

safety instructions

This manual has safety information and instructions to

help you eliminate or reduce the risk of accidents and

injuries.

2.1 Recognize safety information

This is the safety alert symbol. It is used to alert

you to potential physical injury hazards. Obey all

safety messages that follow this symbol to avoid

possible injury or death.

4EN

Explanation of symbols and safety instructions RV So Start Accessory

2.2 Understand signal words

A signal word will identify safety messages and property

damage messages, and also will indicate the degree or

level of hazard seriousness.

WARNING

Indicates a hazardous situation that, if not avoided,

could result in death or serious injury.

CAUTION

Indicates a hazardous situation that, if not avoided,

could result in minor or moderate injury.

NOTICE: Used to address practices not related to

physical injury.

IIndicates additional information that is not related

to physical injury.

2.3 Supplemental directives

To reduce the risk of accidents and injuries, please

observe the following directives before proceeding to

install or operate this appliance:

• Read and follow all safety information and

instructions.

• Read and understand these instructions before

installing or operating this product.

• The installation must comply with all applicable local

or national codes, including the latest edition of the

following standards:

U.S.A.

• ANSI/NFPA70, National Electrical Code (NEC)

• ANSI/NFPA1192, Recreational Vehicles Code

• UL Standard 60947

Canada

• CSA C22.1, Parts l & ll, Canadian Electrical Code

• CSA C22.2 No. 60947

• CSA Z240 RV Series, Recreational Vehicles

2.4 General safety messages

WARNING: Electrical shock hazard.

Before proceeding with the installation of the

SmartStart RV So Start Accessory, all electrical

energy sources supplying the air conditioning unit

must be turned oﬀ at the nearest switch as well as

at the electrical control panel. Aer turning oﬀ all

electrical sources supplying the air conditioning

unit, wait a full ﬁve minutes before proceeding to

install the SmartStart RV So Start Accessory into

the air conditioning unit to avoid potential latent

electrical charge which may be remaining in the air

conditioner’s capacitor. Failure to obey this warning

could result in death or serious injury.

WARNING: Fire hazard.

Ensure all the electrical connections are secure

to maintain the appropriate near-zero resistance

levels. A poor electrical connection in any electrical

circuit can lead to high electrical resistance at

the point of poor connection, resulting in high

temperature and amperage. Not only can this

potentially damage the equipment, it can also result

in a risk of ﬁre. Failure to obey this warning could

result in death or serious injury.

WARNING: Electrical shock, ﬁre, and/

or explosion hazard. Failure to obey the

following warnings could result in death or

serious injury:

• Use only Dometic replacement parts and

components that are speciﬁcally approved for use

with the appliance.

• Avoid improper installation, adjustment, alterations,

service, or maintenance of the appliance. Service and

maintenance must be done by a qualiﬁed service

person only. Installation by a certiﬁed electrician is

highly recommended.

• Do not modify this product in any way. Modiﬁcation

can be extremely hazardous.

• Use care when diagnosing and/or adjusting

components on a powered unit. Disconnect all

remote servicing electric power supplies before

servicing.

5

EN

RV So Start Accessory Intended use

3 Intended use

The SmartStart RV So Start Accessory (hereinaer

referred to as device) reduces the inrush current of

your recreational vehicle’s (RV) air conditioner (AC)

associated with the initial compressor startup. This

reduces and/or eliminates ﬂickering lights, brown-outs,

and nuisance-trip circuit breaker resets. This device is

only suitable for the intended purpose and application in

accordance with these instructions.

This manual provides information that is necessary for

proper installation and/or operation of the device. Poor

installation and/or improper operating or maintenance

will result in unsatisfactory performance and a possible

failure. The manufacturer accepts no liability for any injury

or damage to the product resulting from:

• Incorrect assembly or connection, including excess

voltage

• Incorrect maintenance or use of spare parts

other than original spare parts provided by the

manufacturer

• Alterations to the product without express permission

from the manufacturer

• Use for purposes other than those described in this

manual

Dometic reserves the right to change product

appearance and product speciﬁcations.

4 General information

IThe images used in this document are for reference

purposes only. Components and component

locations may vary according to speciﬁc product

models. Measurements may vary ±0.38 in. (10 mm).

4.1 Tools and materials

Dometic recommends that the following tools and

materials be used while installing the appliance.

Included

parts

Brisk

II

Penguin

II

Blizzard

NXT

FreshJet

Assembled

mounting

bracket and

z-brackets

(attached to the

device)

1 0 0 1

Assembled

mounting

bracket

(attached to the

device)

0 1 1 0

Hose clamp

with worm

screw

0 1 1 0

6 in. wire tie 6 4 10 4

14.5 in. wire tie 0 0 0 2

Device 1

Compressor

wire harness 1

Supply wire

harness 1

Instructions 1

Recommended tools

#2 Phillips screwdriver Multimeter

1/4-4 in. Flat-head screwdriver Needle nose pliers

5/16 in. Deep well nut driver Torque wrench

Drill Utility knife

Electrical tape Wire cutters

Gloves

4.2 Compatibility

This product is compatible with most 120 VAC RV AC

units. This manual speciﬁcally describes installation

for the Dometic Brisk II, Penguin II, Blizzard NXT, and

FreshJet 3 Series Mechanical units. Additional AC units

may be added at future dates.

6EN

General information RV So Start Accessory

4.3 Component locations

This section shows the Dometic Brisk II, Penguin II,

Blizzard NXT, and FreshJet AC unit dimensions, the AC

shroud screw locations, and the inside component

views. It also shows the component views for the device.

uu

yy

ww

ee

qq

rr

tt

ii

1 Brisk II AC unit shroud dimensions

q 13.7 in. (349 mm) u Air ﬂow clearance

area (shaded)

w 29.6 in. (751 mm)

e 27.6 in. (701 mm) i 18.0 in. (457 mm)

clearance

r Front of unit

t Roof opening

y Center line of unit

qq

ww

ee

oo

rr

tt

uu

ii

yy

2 Penguin II AC unit shroud dimensions

q 10.0 in. (264 mm) u 4.0 in. (102 mm)

clearance

w 40.5 in. (1029 mm)

e 29.0 in. (737 mm) i Air ﬂow clearance

area (shaded)

r Front of unit

t Roof opening o 12.0 in. (305 mm)

clearance

y Center line of unit

7

EN

RV So Start Accessory General information

qq

wwee

ii

yy

oo

rr

tt

uu

3 Blizzard NXT AC unit shroud dimensions

q 13.9 in. (353 mm) u 18.0 in. (457 mm)

clearance

w 40.0 in. (1016 mm)

e 30.0 in. (762 mm) i Air ﬂow clearance

area (shaded)

r Front of unit

t Roof opening o 4.0 in. (102 mm)

clearance

y Center line of unit

q

we

r

ty

u

i

4 FreshJet (FJX3000 and FJX4000 series

q13.8 in. (351 mm) t Air ﬂow clearance

area (shaded)

w 29.6 in. (752 mm)

e 27.6 in. (701 mm) y Center line of unit

r 18.0 in. (457 mm)

clearance

u Roof opening

i Front of unit

8EN

General information RV So Start Accessory

uu

yy

ee

tt

qq

ww

rr

5 Brisk II AC unit components and screw locations

q AC shroud t Fan motor

w AC shroud screws t Compressor

e Foam shroud u Condenser Fan

r Electrical box

qq

ww

ee

tt

yy

rr

6 Penguin II AC unit components and screw locations

q AC shroud r Compressor

w AC shroud screws t Fan motor

e Foam shroud y Electrical box

9

EN

RV So Start Accessory General information

qq

ww

ee

tt

yy

rr

uu

7 Blizzard NXT AC unit components and screw locations

q AC shroud t Electrical box

w AC shroud screws y Compressor

e Foam shroud u Fan motor

r Electrical box foam

qq

ww

ee

r

u

y

t

8 FreshJet AC unit components and screw locations

q AC shroud t Condenser Fan

w AC shroud screws y Fan motor

e EPP foam u Capacitor

r Compressor

qq

ww

ee

9 Device exterior

q Device cover screws e Base

w Device cover

10 EN

Speciﬁcations RV So Start Accessory

qq

ww

ee

10 Device components

q Device cover

screws

e LEDs (indicate supply

side of device)

w Device cover

4.4 Model identiﬁcation

This section describes the breakdown of a model

identiﬁcation number.

SMRTST - AC - RV

Application

Appliance

Product

Product SMRTST - Smart Start

Appliance AC - Air Conditioner

Application RV - Recreational Vechicle

Product SMRTST - Smart Start

Appliance AC - Air Conditioner

Application RV - Recreational Vehicle

4.5 Data plate

This section describes the device data plate.

RUN

Design Protected

RUN

FAULT LED

Item# 9610002970

120VAC

11 Device data plate

The device data plate provides information speciﬁc to

the device and is located on the device cover.

5 Speciﬁcations

Full load current <20 A

Frequency range 60 Hz ±3 Hz

Maximum duty cycle at rated

ambient temperature

15 starts per hour

Maximum operating

ambient temperature

140 °F (60 °C)

Enclosure rating IP65/NEMA4

6 Wiring diagrams

WARNING: Electric shock hazard.

Turn the power oﬀ before performing any electrical

installation or maintenance activities. Failure to

obey this warning could result in death or serious

injury.

This section shows examples of the product wiring.

The AC and ADB Wiring Diagram deﬁnitions:

• 120 VAC; 60 Hz 1 PH

• Copper conductors only

11

EN

RV So Start Accessory Wiring diagrams

3

1

Comp Start Assist

6

5

4

3

2

1

LIMIT

HEATER

BLK

BLK *

*

* Not used on

some models

PTCR

BRN

RED

YEL

BLK

GRN/YEL

WHT

O.L.

S

C

R

C

RED

BLU

GRN/YEL

WHT

Compressor

Motor

Fan

Herm

Run Cap

6 Pin Conn

Start

Cap

12 Brisk II AC unit wiring diagram

Compressor

6 Pin Conn

Motor

Fan

Herm

Run Cap

Start

Cap

GRN/YEL

BRN

WHT

BLK

BLU 1

2

3

4

5

6

YEL

RED

(OPT)

PTCR

WHT

C

RS

O.L.

C

*

RED

* Not used on

some models

13 Penguin II AC unit wiring diagram

* Not used on

some models

Compressor

6 Pin Conn

Motor

Fan

Herm

Run Cap Comp. Startter

*Start

Cap

GRN/YEL

BRNWHT

WHT

BLK

BLU 1

2

3

4

5

6

YEL

RED

RED PTCR

WHT

C

RS

O.L.

C

*

RED

14 Blizzard NXT AC unit wiring diagram

Elec Conn

From A/C Thermostat

Rotary Switch

BLK

YEL

RED

BLU C,4

L,3

H,6

GRN/YEL

BLU

BLK

GRN/YELG

L

NWHT

1

1 L1

2 H

4 C

2

3

4

5

6

15 ADB wiring diagram - All AC unit models

12 EN

Wiring diagrams RV So Start Accessory

16 FreshJetX3 series AC unit wiring diagram

17 FreshJetX4 series AC unit wiring diagram

13

EN

RV So Start Accessory Preinstallation

7 Preinstallation

This section describes the bracket preparation required

before installing the device onto the AC unit.

7.1 Bracket conﬁguration

This section describes the bracket conﬁgurations based

on the AC model.

7.1.1 Brisk II and FreshJet bracket

conﬁguration

The mounting bracket and z-brackets should already be

assembled and attached to the device.

If the bracket is not assembled and/or not attached to

the device, go to “Bracket assembly” on page13.

qq

rr

ww

ee

18 Z-bracket direction of slant - Brisk II

q Device e Supply side

w LEDs r Direction of slant

1. With the supply side of the device facing you,

determine the z-bracket’s direction of slant.

IThe two LEDs visible on the outside cover of

the device are located on the supply side of the

device.

– Brisk II - If the z-bracket slants le, go to

“Installation” on page16, otherwise go to

step2.

– FreshJet - If the z-bracket slants right, go to

“Installation” on page16, otherwise go to

step2.

2. Complete steps 1–5 in “Preparing the device” on

page14.

qq

ww

ee

rr

tt

19 Removing the z-brackets and mounting bracket

q Bracket screws r Mounting bracket

w Device t Nuts

e Z-Brackets

3. Using the torque wrench and the #2 Phillips

screwdriver, remove the nuts on the bracket screws.

4. Remove the bracket screws from the mounting

brackets and z-brackets.

5. Switch the brackets so that the slant is in the correct

direction.

6. Conﬁrm that the z-bracket’s direction of slant is

correct for the AC unit model.

– Brisk - le slant

– FreshJet - right slant

7. Complete the steps in “Assembling the brackets -

Brisk II” on page14. to reassemble the brackets to

the device.

14 EN

Preinstallation RV So Start Accessory

7.1.2 Penguin II and Blizzard NXT

conﬁguration

The mounting bracket should already be attached to

the device. To attach the necessary hose clamp, go to

“Attaching the hose clamp” on page15.

If the bracket is not assembled and/or not attached to

the device, go to “Bracket assembly” on page14.

7.2 Bracket assembly

This section describes how to assemble and attach

the bracket assembly to the device if delivered

unassembled. The steps vary based on the AC unit.

To determine the AC unit model, refer to “Model

identiﬁcation” on page10.

7.2.1 Preparing the device

This section describes how to remove the device cover

and position the device.

IPerform the following actions on a ﬂat, clean surface.

1. Place the device on the ﬂat surface with the device

cover facing up.

2. Loosen the four device cover screws and remove the cover.

qq

ww

20 Identifying the LEDs in the device

q Fiber optic rods w LEDs

3. Inspect the underside of the device cover and note

the ﬁber optic rods that align with the LEDs in the

device.

4. Set the device cover aside.

5. Carefully turn the device on its side.

6. Continue with the assembly:

– For Brisk II AC units, go to “Assembling the

brackets - Brisk II” on page14.

– For Penguin II and Blizzard NXT AC units, go to

“Assembling the mounting bracket - Penguin II

and Blizzard NXT” on page15.

7.2.2 Assembling the brackets - Brisk II

This section describes the device’s z-bracket and

mounting bracket assembly for all Brisk II AC units.

qq

ww

ee

rr

tt

21 Securing the z-brackets and the mounting bracket

q Bracket screws r Mounting bracket

w Device t Nuts

e Z-Brackets

1. Inspect the z-brackets to locate the ﬂange end with

the smaller screw holes.

IWhen both z-brackets are installed correctly,

they will mirror each other.

2. Align the smaller screw holes on the ﬂange of one

z-bracket to the screw holes on the

bottom

of the

device.

3. Position the bend in the z-bracket ﬂange against the

device so that the bend points away from the center

of the device.

15

EN

RV So Start Accessory Preinstallation

15 EN

4. Using the #2 Phillips screwdriver, push two bracket

screws through the holes in the device and then

through the small holes in the z-bracket ﬂange.

5. With the mounting bracket on its side, ﬁt the mounting

bracket slots onto the exposed bracket screws.

6. Using the #2 Phillips screwdriver as a backer to hold

the screw in the mounting bracket slot, place a nut at

the end of each bracket screw.

7. Secure each nut at the end of each bracket screw by

two threads so the nuts do not fall oﬀ.

8. Repeat steps 2-7 for the remaining z-bracket, ensuring

the z-bracket is positioned directly against the device.

9. Using the torque wrench and the #2 Phillips

screwdriver, tighten the nuts on the bracket screws to

30 in. lbs (3.4 Nm).

10. While holding the device cover, align the ﬁber optic rods

on the device cover with the LEDs in the device.

11. Replace the device cover.

12. Tighten the device cover screws to 8.8 in. lbs (1Nm).

13. Aligning the ﬁber optic rods on the underside of

device cover to the LEDs in the device, replace the

device cover.

14. Tighten the device cover screws to 8.8 in. lbs (1 Nm).

15. Go to “Installation” on page16.

7.2.3 Assembling the mounting bracket

- Penguin II and Blizzard NXT

This section describes the device’s mounting bracket

assembly for all Penguin II and Blizzard NXT AC units.

qq

ww

ee

rr

22 Securing the mounting bracket

q Bracket screws e Mounting bracket

w Device - supply side r Nuts

1. Place one bracket screw into each of the mounting

hole locations.

2. Turn the mounting bracket on its side and align the

holes with the mounting bracket holes on the back

side of the device.

3. Using the #2 Phillips screwdriver, push the bracket

screws through the

mounting bracket holes

.

4. Place a nut at the end of each bracket screw.

5. Using the 5/16 in. deep well nut driver and the #2

Phillips screwdriver, tighten the nuts on the bracket

screws, then loosen by one-half turn.

IDo not fully tighten the nuts yet.

6. Go to “Attaching the hose clamp” on page15.

7.3 Attaching the hose clamp

This section describes how to attach the hose clamp to

the mounting bracket for all AC units , if applicable.

1. Place the device on its side with the supply side to

the right and the mounting bracket towards you.

IThe two LEDs visible on the outside cover of

the device are located on the supply side of the

device.

16 EN

Installation RV So Start Accessory

16

EN

oo

ww

ee

qq

rr

yy

tt

uu

ii

23 Attaching the hose clamp (supply side on the right)

q LED location

on the device cover

t Worm screw

y Slot - supply side

w Slot - compressor side u Bracket screws

e Mounting bracket i Nuts

r Hose clamp o Device - supply side

2. Insert the hose clamp end into the slot on the supply

side of the mounting bracket.

3. Push the hose clamp through to the other side of the

mounting bracket.

IIf it is diﬃcult to push the hose clamp through

the mounting bracket, loosen the nuts on the

bracket screws several turns.

4. Push the hose clamp end through the slot on the

compressor side of the mounting bracket.

IIf the hose clamp does not easily align with the

compressor side slot, use the needle nose pliers

to guide it into place.

5. Continue pushing the hose clamp through the

mounting bracket until the worm screw is next to the

slot on the supply side of the device.

6. If the nuts on the bracket screws were loosened in

step 3, use the torque wrench and the #2 Phillips

screwdriver to tighten the nuts to 30 in. lbs (3.4 Nm).

7. Aligning the ﬁber optic rods on the underside of

device cover to the LEDs in the device, replace the

device cover.

8. Tighten the device cover screws to 8.8 in. lbs (1 Nm).

9. Go to “Installation” on page16.

8 Installation

WARNING: Fire or electric shock hazard.

Failure to obey the following warnings could

result in death or serious injury.

• Shut oﬀ the gas supply, turn oﬀ the AC circuit breaker,

disconnect the 120 VAC power from the RV, and

disconnect the positive (+) 12VDC terminal from the

supply battery before drilling or cutting into the RV

or before performing any preinstallation, installation, or

maintenance activities. Do not install the device unless

power to the AC unit is oﬀ.

• There is a risk of electrical shock from the energy

stored in the capacitors. Wait for ﬁve minutes aer

the shutdown of equipment before performing any

preinstallation, installation, or maintenance activities.

• Make sure there are no obstacles such as wires or

pipes inside the RV’s roof.

• Provide grounding in compliance with all applicable

electrical codes.

• Once installed, the device operates without need for

user input. See the speciﬁc AC unit’s and/or speciﬁc

controls Installation and Operation Manual for AC

operating instructions.

CAUTION: Liing hazard.

Use proper liing technique and control when

liing the AC unit. Failure to obey this caution could

result in minor or moderate injury.

NOTICE: Maintain the structural integrity of the RV roof.

The roof must be designed to support 130 lbs (59 kg)

when the RV is in motion. Normally, a 200 lb (91 kg)

static load design will meet this requirement. Failure to

follow this notice could result in

damage to the rooop

component, device, or the RV

.

INever create a low spot on the RV roof.

17

EN

RV So Start Accessory Installation

This section describes how to install the device. The

installation procedures and components vary by the AC

unit model.

Brisk II Go to “Installing the device - Brisk II” on

page17.

Penguin II Go to “Installing the device - Penguin II” on

page22.

Blizzard

NXT

Go to “Installing the device -Blizzard NXT” on

page26.

FreshJet Go to “Installing the device - FreshJet 3 Series

Mechanical” on page31.

8.1 Installing the device - Brisk II

NOTICE: Do not force the AC shroud during removal.

Failure to follow this notice can damage or break the

screw holes and require an AC shroud replacement.

This section describes how to access the installation

area, disconnect the existing wiring, mount the device,

install and connect the new wiring, and close the unit

aer completing the installation in a Brisk II AC unit.

8.1.1 Removing the shrouds

qq

ww

ee

rr

24 Brisk II AC unit components and screw locations

q AC shroud e Foam shroud

w AC shroud screws r Electrical box

1. Using the #2 Phillips screwdriver, remove and set

aside the four AC shroud screws and the AC shroud.

IThe AC shroud should li oﬀ easily. If it does

not, verify all the AC shroud screws have been

removed.

ITurn the AC shroud upside down to store the

screws and other small parts removed during

the installation process.

2. Remove the internal foam shroud by pulling up

vertically on the sides and set it aside.

18 EN

Installation RV So Start Accessory

qq

ww

ee

25 Removing the electrical box cover

q Electrical box cover

screws

e Electrical box

cover

w Electrical box

3. Verify that the bracket is mounted on the device in the

correct position.

4. Using the 5/16 in. deep well nut driver, remove the

two screws on the top of the electrical box cover and

set aside.

5. Remove the electrical box cover from the electrical

box, sliding the electrical box cover up and away

from the electrical box.

8.1.2 Disconnecting the compressor

wires

WARNING: Electric shock hazard.

There is a risk of electrical shock from the energy

stored in the capacitors. Wait for ﬁve minutes aer

the shutdown of equipment before performing

any installation activity. Failure to obey this warning

could result in death or serious injury.

qq

ww

26 Disconnecting the compressor wires from the capacitor

q Capacitor w Red and white compressor

wires

1. Using a multimeter, conﬁrm that the capacitor is fully

discharged.

2. Disconnect the red and white compressor wires from

the capacitor inside the electrical box.

qq

ww

ee

rr

rrtt

yy

27 Disconnecting the compressor wires from the compressor

q Compressor

cap nut

r White, red, and blue

factory compressor wires

w Compressor cap t Wire tie

e Compressor y Fan motor mount

19

EN

RV So Start Accessory Installation

3. Using the 5/16 in. deep well nut driver, locate and

remove the compressor cap nut and compressor cap

from the top of the compressor.

4. Disconnect the white, red, and blue factory

compressor wires from the compressor.

5. Using a 6 in. (15.2 cm) length of electrical tape,

secure the compressor wire terminals together and

cover the terminal ends with electrical tape. Use

more electrical tape if needed to cover the terminal

ends completely to ensure no metal is exposed.

qq

ww

ee

28 Disconnecting the compressor wire harness

q Compressor wire

harness

e Factory compressor

wires inside the foam

electrical enclosure

w Strain relief

6. Tuck the taped factory compressor wires into the

foam electrical enclosure.

7. Starting at the compressor, trace the white wire to the

fan motor mount.

8. Using your ﬁngers to pinch the white wire close to

the fan motor mount, pull on the white wire to verify it

is loose and not attached to the capacitor.

8.1.3 Installing the new supply wire

harness

qqww

29 Connecting the harnesses

q Supply wire harness w AC wire harness plug

1. Insert the AC wire harness plug into the supply wire

harness included with the device.

qq

ww

ee

rr

30 Securing the strain relief

q Gasket putty e Strain relief screw

w Foam electrical

enclosure

r Existing cable route

2. Remove the gasket putty, reserving it for later reuse.

3. Using the 5/16 in. deep well nut driver, locate and

remove the outer strain relief screw from the strain

relief.

4. Route the blue wire from the supply wire harness

through the foam electrical enclosure and strain relief.

IUse the existing cable as a guide for routing the

blue wire.

20 EN

Installation RV So Start Accessory

5. Using the 5/16 in. deep well nut driver, insert the

outer strain relief screw into the strain relief and

tighten until snug.

qq

ww

ee

rr

tt

yy

31 Routing wires through the fan motor mount to the capacitor

q Control box cavity r Capacitor

w Red and white

capacitor wires

t Fan motor mount

(second hole)

e Fan motor mount

(ﬁrst hole)

y Wire bundle

6. Route the supply wire harness through the control

box cavity.

7. Insert the red and white supply harness wires into the

ﬁrst hole of the fan motor mount and push the wires in

toward the second fan motor mount hole.

8. From the condenser side of the fan motor mount,

reach into the fan motor mount and pull the red and

white capacitor wires through the second hole in the

fan motor mount.

IBefore passing the wires through the second

fan motor mount hole, arrange them to curve

toward the condenser to easily pass from the fan

motor mount to the hole in the electrical box.

9. Pull the red and white wires through the second fan

motor mount hole and into the electrical box, pulling

them through to the electrical box area.

10. On the capacitor, connect the red wire to the HERM

terminal.

11. On the capacitor, connect the white wire to the COM

terminal.

12. Use a wire tie to secure the new supply harness

wires, and the factory compressor wires terminals

disconnected from the capacitor, to the existing

wire bundle.

13. Ensure the secured factory compressor wires cannot

come into contact with the top of the capacitor.

8.1.4 Mounting the device - Brisk II

NOTICE: If the fan motor washers stick to the fan motor

grommets, use the needle nose pliers to carefully pry

them oﬀ. Do not use a screwdriver or sharp object.

Failure to follow this notice can damage the fan motor

grommets.

This section describes how to mount the device onto a

Brisk II AC unit.

qq

ww

ee

yy

rr

tt

32 Mounting the device and mounting bracket for the Brisk II

q Device r Fan motor nuts

w Supply side t Fan motor studs

e Z-brackets y Fan motor

1. Locate the fan motor in the AC unit.

2. Using the 5/16 in. deep well nut driver, remove the

four fan motor nuts from the fan motor studs and set

aside.

3. Remove and discard the four fan motor washers

without damaging the fan motor grommets

underneath.

4. Holding the device with the supply side of the device

towards the compressor, place the device onto the

fan motor so the mounting studs pass through the

holes in the z-brackets.

Strona się ładuje...

Dometic SmartStart RV Instrukcja obsługi

Dometic SmartStart RV Instrukcja obsługi

w innych językach

Inne dokumenty