AAT NVIP-3SD-8200/30 Instrukcja obsługi

Kategoria
Kamery ochrony
Typ
Instrukcja obsługi
U s e r s m a n u a l
NVIP-5000 series IP PTZ camera
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
2
All rights reserved © AAT Holding S.A
2
IMPORTANT SAFEGUARDS AND WARNINGS
EMC (2004/108/EC) and LVD (2006/95/EC ) Directives
CE Marking
Our products are manufactured to comply with requirements of the following directives and national regulations
implementing the directives:
 Electromagnetic compatibility EMC 2004/108/EC.
 Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical
equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as
75VDC and 1500VDC.
WEEE Directive 2002/96/EC
Information on Disposal for Users of Waste Electrical and Electronic Equipment
This appliance is marked according to the European 1000VAC Directive on Waste Electrical and Electronic
Equipment (2002/96/EC) and further amendments. By ensuring this product is disposed of correctly, you will
help to prevent potential negative consequences for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product.
The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be
treated as household waste. It shall be handed over to the applicable collection point for used up electrical and
electronic equipment for recycling purpose. For more information about recycling of this product, please contact
your local authorities, your household waste disposal service or the shop where you purchased the product.
RoHS Directive 2002/95/EC
Out of concern for human health protection and friendly environment, we assure that our products
falling under RoHS Directive regulations, regarding the restriction of the use of hazardous
substances in electrical and electronic equipment, have been designed and manufactured in
compliance with the above mentioned regulations. Simultaneously, we claim that our products have
been tested and do not contain hazardous substances whose exceeding limits could have negative
impact on human health or natural environment
Information
The device, as a part of professional CCTV system used for surveillance and control, is not designed for self
installation in households by individuals without technical knowledge.
Excluding of responsibility in case of damaging data on a disk or other devices:
The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices
during device operation.
WARNING!
PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN
PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE
PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE
PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF
EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN ACTION.
IP PTZ cameras NVIP-5000 series - user manual ver.1.0.
All rights reserved © AAT Holding S.A
3
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
IMPORTANT SAFEGUARDS AND WARNINGS
WARNING!
THE KNOWLEDGE OF THIS MANUAL IS AN INDISPENSIBLE CONDITION OF A PROPER
DEVICE OPERATION. YOU ARE KINDLY REQEUSTED TO FAMILIARIZE YOURSELF WITH
THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.
WARNING!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO
USER-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE
PERSONNEL MAY OPEN THE UNIT
INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE
PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS
1. Prior to undertaking any action please consult the following manual and read all the safety and operating
instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual
is necessary;
3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct
influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s
manual;
5. The device should be disconnected from power sources during maintenance procedures;
6.
Usage of additional devices and components neither provided nor recommended by the producer
is forbidden;
7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,
damp basements);
8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not
recommended since it may lead to heat build-up and damaging the device itself as a consequence;
9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly
mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted
by qualified personnel with proper authorization, in accordance with this user’s manual.
10. Device should be supplied only from a power sources whose parameters are in accordance with those
specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera
from a power sources with unknown parameters, unstable or not meeting producer’s requirements;
Due to the product being constantly enhanced and optimized, certain parameters and functions described in the
manual in question may change without further notice. We strongly suggest visiting the www.novuscctv.com
website in order to access the newest manual
Data included in the following user’s manual is up to date at the time of printing. AAT Holding Sp z o.o. holds
exclusive rights to modify this manual. The producer reserves the rights for device specification modification
and change in the design without prior notice.
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
4
All rights reserved © AAT Holding S.A
4
TABLE OF CONTENTS
1. START-UP AND INITIAL IP CAMERA CONFIGURATION................................. 6
1.1. Overview .............................................................................................................. 6
1.2. Starting the IP camera .......................................................................................... 6
1.3. Initial configuration via the Web browser ........................................................... 7
2. NETWORK CONNECTION UTILIZING WEB BROSWER .................................. 8
2.1. Recommended PC specification for web browser ............................................... 8
2.2. Initial configuration via the Web browser ........................................................... 8
3. WWW INTERFACE - WORKING WITH IP CAMERA ........................................ 12
3.1. Displaying live pictures. .................................................................................... 12
3.2. Sensor Setting. ................................................................................................... 14
3.2.1. Description of Sensor Settings menu options ..................................... 14
3.3. Playback............................................................................................................. 20
3.4 Device Info..............................................................................................................
3.5. Stream Configuration......................................................................................... 21
3.6. Device Configuration ........................................................................................ 22
3.6.1. Local Network. ..................................................................................... 22
3.6.2. Device Port. .......................................................................................... 23
3.6.3 ADSL Network. .................................................................................... 24
3.6.4. Camera. ................................................................................................. 24
3.6.5. Data....................................................................................................... 25
3.6.6. OSD. ..................................................................................................... 26
3.6.7. Microphone........................................................................................... 27
3.6.8. Dome PTZ ............................................................................................ 28
3.6.9. BNC Output.......................................................................................... 28
3.6.10. System Configuration......................................................................... 28
3.7. External Devices. ............................................................................................... 28
3.8. Alarm Configuration.......................................................................................... 29
3.8.1. Alarm I/O............................................................................................... 29
3.8.2. Disk Alarm Linkage............................................................................... 30
3.8.3. Network Alarm. ..................................................................................... 30
3.8.4. I/O Alarm Linkage................................................................................. 31
3.8.5. Motion Alarm ........................................................................................ 32
3.9. Local Record...................................................................................................... 33
IP PTZ cameras NVIP-5000 series - user manual ver.1.0.
All rights reserved © AAT Holding S.A
5
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
3.10. Privacy Masking. ............................................................................................. 34
3.11. Network Services............................................................................................. 35
3.11.1. PPPoE........................................................................................... 35
3.11.2. DDNS. .......................................................................................... 35
3.12. Service Center.................................................................................................. 36
3.12.1. Alarm Center. ............................................................................... 36
3.12.2. SMTP............................................................................................ 36
3.13. Privilege Manager............................................................................................ 37
3.13.1. Group............................................................................................ 37
3.13.2. User. ............................................................................................. 39
3.14. Protocol............................................................................................................ 41
3.14.1. Protocol Info................................................................................. 41
3.14.2. Security......................................................................................... 41
3.15. Device Log....................................................................................................... 42
3.15.1. Operation Log.............................................................................. 42
3.15.2. Alarm Log.................................................................................... 43
3.15.3. Collect Log. ................................................................................. 44
3.16. Maintenance..................................................................................................... 44
3.16.1. System Service............................................................................. 44
3.16.2. Device Restart.............................................................................. 45
3.16.3. Default Settings ........................................................................... 45
4. PTZ OPTIONS AVAILABLE THROUGH NMS SOFTWARE................................ 46
4.1 Preliminary information....................................................................................... 46
4.1.1. Preset. function ............................................................................. 46
4.1.2. Track function............................................................................... 47
4.1.3. Scan function. ............................................................................... 47
4.1.4. Tour function. ............................................................................... 48
4.1.5. Idle function.................................................................................. 48
4.1.6. Geographical orientation (North) function. ................................. 49
4.1.7. Timer function............................................................................... 49
5. ADDITIONAL INFORMATION ABOUT THE PRESET FUNCTION ................ 50
5.1 Preliminary information...................................................................................... 50
5.2 List of presets with special meanings ................................................................. 50
6. NOTES........................................................................................................................... 51
FOREWORD INFORMATION
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
6
All rights reserved © AAT Holding S.A
6
1. START-UP AND INITIAL IP CAMERA CONFIGURATION
1.1. Overview
Following manual for IP Cameras NVIP-5000 series contains detailed information about camera
connection and operation, main page introduction, system related settings and camera settings.
Note
In this document you can find all available functionality present in described series of cameras.
Depending on camera model some features might be unavailable or unsupported.
1.2. Starting the IP camera
To run NOVUS IP camera you have to connect ethernet cable between camera and network switch and
you have to connect 24 VAC power adaptor, at least 50W.
Initialization process takes about 2 minutes. Then you can proceed to connect to the camera via web
browser.
The recommended way to start an IP camera and perform its configuration is connect directly to the
network switch which is not connected to other devices.
To obtain further information about network configuration parameters (IP address, gateway, network
mask, etc.) please contact your network administrator.
 Network connection using external power supply and network switch
START-UP AND INITIAL CAMERA CONFIGURATION
IP Camera
Network transmission
Network
transmission
Network Switch
Computer
IP PTZ cameras NVIP-5000 series - user manual ver.1.0.
All rights reserved © AAT Holding S.A
7
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
 Network connection using external power supply, directly to the computer.
1.3. Initial configuration via the web browser
The default network settings for IP PTZ cameras 5000 series are :
1. IP address = 192.168.1.200
2. Network mask - 255.255.255.0
3. Gateway - 192.168.1.1
4. User name - root
5. Password - pass
Knowing the camera’s IP address you need to set PC IP address appropriately, so the two devices can
operate in one network subnet (e.g. for IP 192.168.1.1, appropriate address for the camera is from range
192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for
camera and PC computer
You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera
yourself or select DHCP mode (DHCP server is required in this method in target network) by using
web browser or by NMS software. When you use DHCP server check IP address lease and its linking
with camera MAC address to avoid changing or losing IP address during device operation or network/
DHCP server breakdown. You have to remember to use a new camera IP address after changing
network parameters.
After network setting configuration has been done, the camera can be connected to a target network.
START-UP AND INITIAL CAMERA CONFIGURATION
IP Camera
Network transmission - cross over cable
Computer
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
8
All rights reserved © AAT Holding S.A
8
2. NETWORK CONNECTION VIA WEB BROSWER
2.1. Recommended PC specification for web browser connections
Requirements below apply to connection with an IP camera, assuming image display in 1920x1080
resolution and 30 fps speed.
1. CPU Intel Pentium IV 3 GHz or faster
2. RAM Memory min. 1 GB
3. VGA card (any displaying Direct 3D with min. 128 MB RAM memory)
4. OS Windows XP / VISTA / Windows 7 / Windows 8
5. Direct X version 9.0 or newer
6. Network card 10/100/1000 Mb/s
2.2. Connection with IP camera via web browser
You have to enter camera IP address in the web browser address bar. If IP address is correct user login
window will be displayed:
Default user is root and default password is pass.
In the Language box you can change the display language. The default language is English.
For safety reasons, it is recommended to change default user name and password.
It is possible to connect to the camera using Internet Explorer, Mozilla Firefox, Chrome or Opera
browsers. Running the IP camera in this browsers are very similar.
NETWORK CONNECTION VIA WEB BROWSER
IP PTZ cameras NVIP-5000 series - user manual ver.1.0.
All rights reserved © AAT Holding S.A
9
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
If your computer has Flash Player
ins
t
a
ll
ed,
the main screen
for the
camera web interface
opens.
From
here you can view and configure
the
ca
m
e
ra
.
NOTE:
If your computer
does
not
have
Flash Player
ins
t
a
ll
ed,
you will be prompted
t
o
select if
y
o
u
would
like
t
o
use
Activ
eX
or Flash
Play
er
t
o
connect to the
ca
m
e
ra:

Click
Click
here to shift playing life video with short delay widget! to
play
live
video
with
ActiveX
control
to
reduce
latency
(recommended): Uses
an
ActiveX
plug-in to connect to the camera. To
install the plug-in, click on the
video
area,
and
select Install
this
Add-on for all
users on this
computer
,
and follow the
prompts.
NOTE:
Please open the
Security settings
of IE browser, and enable the
Download unsigned
ActiveX controls.

Click
Please
download
the latest
version
of
Flash
Player to
play
live video:
Opens
a link to
download Flash Player from
Adobe’s
website.
After
completing the installation, restart your
browser and reconnect to
the
camera.
NOTE: When working in Windows Vista/7/8 the ActiveX applet may be blocked by Windows
Defender or User account control. In such case you should allow to run this applet, or simply disable
these functions.
NETWORK CONNECTION UTILIZING WEB BROWSER
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
10
All rights reserved © AAT Holding S.A
10
NETWORK CONNECTION VIA WEB BROWSER
NOTE: If you are running Windows Vista/7/8 with Internet Explorer 11, the ActiveX applet can be
blocked through browser security settings. In this situation, you should: add the IP address of the ca-
mera to the view of compatibility (Tools -> Compatibility View Settings, click Add).
Then, in the security settings options, add the camera address to trusted sites and lower the security
level to a minimum.
IP PTZ cameras NVIP-5000 series - user manual ver.1.0.
All rights reserved © AAT Holding S.A
11
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
NETWORK CONNECTION UTILIZING WEB BROWSER
After making the changes, restart the browser, re-connect to the camera and log on.
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
12
All rights reserved © AAT Holding S.A
12
3. WWW INTERFACE - WORKING WITH IP CAMERA
3.1. Displaying live pictures
1.Camera settings
Live Video - Live video preview
Playback* - Playback records form SD card
Device Info - Device information
Stream Configuration - Video and audio settings for each stream
Device Configuration - Device configuration (e.g. Local Network, Date&Time)
External Device - External device configuration (function unavailable)
Alarm Configuration - Alarm Configuration (Motion alarm, Alarm I/O)
Local Record - Local Record Configuration
Privacy Masking - Privacy zones options
Network Service - Network services configuration (e.g. DDNS)
Service Center - Service center configuration (e.g. SMTP)
Privilege Manager - Users and groups management
Protocol - Protocols settings (e.g. ONVIF)
Device Log - Device Log contains: Operation Log, Alarm Log and Collect Log
Maintenance - Device Restart and restoring Default Settings
*This option is inactive
WWW INTERFACE - WORKING WITH IP CAMERA
3.
4.
1.
2.
5.
IP PTZ cameras NVIP-5000 series - user manual ver.1.0.
All rights reserved © AAT Holding S.A
13
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
2. Video Parameter
Stream - Stream ID (choose one from available streams)
Bite Rate Type - Information about bit rate type
Bit Rate (kbps) - Information about bit rate
I Frame Interval - Information about I frame interval
Quality - Information about quality
3. PTZ Control Panel
PTZ Configure:
Preset - Programming, deleting, and recalling presets*
Track - Programming, deleting, and recalling tracks
Speed - Setting speed of movement
3D Position - Turn on/off control using the mouse
North - Setting orientation of the camera
Timer - Setting schedules
PTZ Control:
Arrow keys - Controlling the movement of the camera: up/down, right/left
„Home” key - Function unavailable
Zoom - Zoom control
Focus - Focus control
Iris - Function unavailable
Brush - Function unavailable
On/Off IR - Function unavailable
4. Menu bar
Change Password - Change users password
Sign Out - Logout from the camera menu and the option to change the menu
language
5. Video Control
Camera - Default number of the camera is 1.
Video - Turn on/off video
Audio - Turn on/off audio
Interphone - Turn on/off Interphone
NOTICE: Audio and Interphone functions will not be available when using Flash instead of ActiveX.
*- additional information about the presets are available on page 50
WWW INTERFACE - WORKING WITH IP CAMERA
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
14
All rights reserved © AAT Holding S.A
14
3.2. Sensor Setting
Sensor Settings menu allows you to adjust the image settings and to control certain camera functions.
To access this menu, press the right mouse button on the video window in the Video Preview tab, and
then select Configure sensor.
To restore factory settings, press the default settings and confirm the operation. To revert to the last
saved settings, press the Reset button.
After each change the sensor settings, click Save to save your parameters. To exit the sensor
configuration without saving your settings, press the X button of the window.
3.2.1. Description of the option menu item: Sensor Settings
Change Settings
To make any changes to the sensor settings, switch to Debug Mode, visible in the lower left corner of
each window configuration. In addition, each sensor settings can be saved in one of the four available
configuration profiles. Any changes confirm the Save button.
Saving settings Whenever the window is closed Sensor Settings window appears informing us about
switching from edit mode in preview mode.
- Yes - Sensor Settings window closes, another
opens a window opens preview mode.
- No - Sensor Settings window closes, another
opens a window opens editing mode.
- Cancel - return to the Settings dialog Sensor.
Depending on the option selected more openly Sensor Settings window will run in debug mode or the
preview mode.
WWW INTERFACE - WORKING WITH IP CAMERA
IP PTZ cameras NVIP-5000 series - user manual ver.1.0.
All rights reserved © AAT Holding S.A
15
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
Time Segment Tab
On the Time Segment we have the ability to configure, schedule of the camera by selecting the start and
end of the recording
- Start Time - select the hour (0-24) and minutes (0-50) in which the camera starts its work
- End Time - select the hour (0-24) then the minute in which the camera finishes its work.
Image Adjust Tab
On the Image Adjust setting you can adjust the brightness, color saturation, sharpness, contrast of the
image from the camera. Furthermore, it is possible to set the level of gamma correction and noise
reduction for color component.
WWW INTERFACE - WORKING WITH IP CAMERA
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
16
All rights reserved © AAT Holding S.A
16
Image Setting Tab
- Image Settings - you can choose how the image rotation: Horizontal, Vertical, Flip
(simultaneous turning horizontally and vertically), and Off
- Still image - allows you to freeze the image.
Exposal Setting Tab
On the Exposal Setting tab, you can set the exposure mode of action of the automation of the camera:
- Auto - Where the camera automatically adjusts to the lighting conditions on the limit list to
strengthen you can also select the maximum amplification level
- Manual - where the user selects the shutter speed value (in the range of 1/25 to 1/10000), the
aperture (in the range of F1.6 to F14) and the reinforcement (0 to 30dB) and its limit.
- Shutter Priority - where you can manually set the shutter speed (between 1/25 to 1/10000) and
limit gain, and the camera automatically adjusts the aperture value
- Aperture Priority - where you can manually set the aperture value (ranging from F1.6 to F14)
and limit gain, and the camera will automatically adjust the shutter value
In addition, the ability to enable or disable the DSS which the maximum value is 1 second.
WWW INTERFACE - WORKING WITH IP CAMERA
IP PTZ cameras NVIP-5000 series - user manual ver.1.0.
All rights reserved © AAT Holding S.A
17
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
WB Setting Tab
On the WB Setting can be set up the way you work automation WB:
- Inside - option dedicated while the camcorder is inside the room
- Outdoors - dedicated option when the camera is running outdoor
- Triggered one button - option inactive
- ATW - Automation option when the camera adjusts the white balance to the currently observed
area
- Manual - user set level off R (0 to 255) and B (0 to 255)
- Fluorescent light - optional dedicated to work by the light of fluorescent lamps
- Sodium lamps - the option is dedicated to work by the light of sodium lamps
D/N Setting Tab
On the D/N Setting can choose whether the camera is in automatic mode, day mode, night mode or
using the scheduler.
- In Auto mode - the camera will automatically adjust the mode to lighting conditions.
- In Day Mode - forces the camera in color.
- The Night Mode - forces the camera in black/white.
- In the Scheduler - user you can decide what time the camera switches from day mode to night
and from night mode to day mode.
WWW INTERFACE - WORKING WITH IP CAMERA
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
18
All rights reserved © AAT Holding S.A
18
Infrared Tab
On the Infrared, you can control how the IR illumination works:
- In Auto mode - the camera automatically adjusts the lighting power IR LEDs, depending on the
size of the optical zoom and external conditions.
- In Manual mode - power IR illuminator can be set by the user independently for each of the
three groups of IR LEDs (near, middle and far).
Lens Setting Tab
On the Lens Setting, we can set the following parameters:
- DZoom - Enable or disable the digital zoom option (12x).
- Focus Mode - choose the type of work focusing mechanism: Auto - the camera itself sharpens
the image, depending on the observed area, Manual - in this mode, the user selects when to
sharpen the image using Auto Focus Once button now, PUSH - after camera focused on one
area, it wont focus on new objects, that appear in focused zone.
- AF Sensitivity - choose the sensitivity of focus. Possible options: high, medium, low.
- Focus Near Limit - we can set the limit of the camera zooms to the selected distance of 1.5m,
2m, 3m, 6m, 10m and infinity.
WWW INTERFACE - WORKING WITH IP CAMERA
IP PTZ cameras NVIP-5000 series - user manual ver.1.0.
All rights reserved © AAT Holding S.A
19
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
NR Tab
In Noise Reduction tab, we can set three modes:
- Auto - the camera decides to include noise correction 3DNR. Additionally, you can divide the
maximum level of compensation.
- Manual - manually adjust the level (default 50) digital noise reduction.
- Off - mode, digital noise reduction is turned off.
Special Function Tab
In Special Function Tab, you can set the camera:
- WDR - enables or disables the WDR (Wide Dynamic Range)
-Anti Fog - feature improved visibility in bad weather (fog rain)
- BLC - rear backgrounds compensation function that eliminates the effect resulting from
observing the area with too strong light source in the background.
- HLC - the ability to enable or disable the HLC, which reduces the brightness of the areas
observed by the camera in order to provide better image quality.
WWW INTERFACE - WORKING WITH IP CAMERA
NVIP-5000 series IP PTZ camera - user manual ver.1.0.
All rights reserved © AAT Holding sp. z o.o.
20
All rights reserved © AAT Holding S.A
20
3.3 Playback - option not available
3.4. Device Info
Device Info menu allows user to view information about camera and change the device name.
In DEVICE NAME box, you can type your own name for the camera. To set your own name, enter it in
this field, previously deleting the default name, and press the SET button.
WWW INTERFACE - WORKING WITH IP CAMERA
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104

AAT NVIP-3SD-8200/30 Instrukcja obsługi

Kategoria
Kamery ochrony
Typ
Instrukcja obsługi

w innych językach