Novus VIP-12DN7023V/IR-1P Instrukcja obsługi

Kategoria
Kamery ochrony
Typ
Instrukcja obsługi

Ten podręcznik jest również odpowiedni dla

U s e r s m a n u a l
(short form)
NVIP-12DN7023V/IR-1P
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
2
IMPORTANT SAFEGUARDS AND WARNINGS
EMC (2004/108/EC) and LVD (2006/95/EC ) Directives
CE Marking
Our products are manufactured to comply with requirements of the following directives and national regulations
implementing the directives:
Electromagnetic compatibility EMC 2004/108/EC.
Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical
equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well as
75VDC and 1500VDC.
WEEE Directive 2012/19/EU
Information on Disposal for Users of Waste Electrical and Electronic Equipment
This appliance is marked according to the European 1000VAC Directive on Waste Electrical and Electronic
Equipment (2002/96/EC) and further amendments. By ensuring this product is disposed of correctly, you will
help to prevent potential negative consequences for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product.
The symbol on the product, or the documents accompanying the product, indicates that this appliance may not be
treated as household waste. It shall be handed over to the applicable collection point for used up electrical and
electronic equipment for recycling purpose. For more information about recycling of this product, please contact
your local authorities, your household waste disposal service or the shop where you purchased the product.
RoHS Directive 2011/65/EU
Out of concern for human health protection and friendly environment, we assure that our products
falling under RoHS Directive regulations, regarding the restriction of the use of hazardous substances
in electrical and electronic equipment, have been designed and manufactured in compliance with the
above mentioned regulations. Simultaneously, we claim that our products have been tested and do
not contain hazardous substances whose exceeding limits could have negative impact on human
health or natural environment
Information
The device, as a part of professional CCTV system used for surveillance and control, is not designed for self
installation in households by individuals without technical knowledge.
Excluding of responsibility in case of damaging data on a disk or other devices:
The manufacturer does not bear any responsibility in case of damaging or losing data on a disk or other devices
during device operation.
WARNING!
PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN PRODUCT IN
USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE PRODUCT, OR IF IT DOES
NOT ARISE FROM THE USUAL APPLICATION OF THE PRODUCT, MANUFACTURER MUST BE
CONTACTED UNDER THE RIGOR OF EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR
THE RESULTS OF SUCH AN ACTION.
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
3
IMPORTANT SAFEGUARDS AND WARNINGS
WARNING!
THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER
DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH
THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.
WARNING!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER
-SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL
MAY OPEN THE UNIT
INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE
PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS
1. Prior to undertaking any action please consult the following manual and read all the safety and operating
instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual is
necessary;
3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct
influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with the user’s
manual;
5. The device should be disconnected from power sources during maintenance procedures;
6. Usage of additional devices and components neither provided nor recommended by the producer is
forbidden;
7. You are not allowed to use the camera in high humidity environment (i.e. close to swimming pools, bath tubs,
damp basements);
8. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.) is not
recommended since it may lead to heat build-up and damaging the device itself as a consequence;
9. Mounting the camera on unstable surface or using not recommended mounts is forbidden. Improperly
mounted camera may cause a fatal accident or may be seriously damaged itself. The camera must be mounted
by qualified personnel with proper authorization, in accordance with this user’s manual.
10. Device should be supplied only from a power sources whose parameters are in accordance with those
specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the camera
from a power sources with unknown parameters, unstable or not meeting producer’s requirements;
Due to the product being constantly enhanced and optimized, certain parameters and functions described in the
manual in question may change without further notice. We strongly suggest visiting the www.novuscctv.com
website in order to access the newest manual
Data included in the following user’s manual is up to date at the time of printing. AAT Holding S.A. holds
exclusive rights to modify this manual. The producer reserves the rights for device specification modification
and change in the design without prior notice.
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
4
TABLE OF CONTENTS ..................................................................................................... 4
1. FOREWORD INFORMATION ................................................................................... ..5
1.1. General Characteristics ........................................................................................ 5
1.2. NVIP-12DN7023V/IR-1P tech specification .................................................. ...6
1.3. Camera dimension ........................................................................................... ...7
1.4. Package contents ............................................................................................... ...8
2. START-UP AND INITIAL IP CAMERA CONFIGURATION ................................. 9
2.1. Description of connectors and control tools ........................................................ 9
2.2. Connecting power supply to the camera ......................................................... ..10
2.3. NVIP-12DN7023V/IR-1P mounting ................................................................. 10
2.4. Starting the IP camera ........................................................................................ 11
2.5. Initial configuration via the Web browser ......................................................... 12
3. NETWORK CONNECTION UTILIZING WEB BROSWER ................................ 13
3.1. Min. PC specification for web browser .............................................................. 13
3.2. Connection with IP camera via the Internet Explorer ........................................ 13
3.3. Connection with IP camera via the other browser ............................................. 15
4. WWW INTERFACE - WORKING WITH IP CAMERA ......................................... 17
4.1. Displaying live video. ......................................................................................... 17
5. CONNECTING ACCESSORIES ................................................................................ 19
5.1. Description of connection Alarm and Audio I/O. .............................................. 19
5.2. SD card installation ........................................................................................... 21
6. RESTORING FACTORY DEFAULTS ..................................................................... 22
6.1. Restoring software factory defaults .................................................................... 22
6.2. Restoring hardware factory defaults in IP cameras ........................................... 22
TABLE OF CONTENTS
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
5
1. FOREWORD INFORMATION
1.1. General Characteristics
Mechanical IR cut filter
IR operation capability
Imager resolution: 12 megapixels
Min. Illumination: from 0.01 lx/F=2.8 (0 lx - IR On)
Wide Dynamic Range (WDR)
Digital Slow Shutter (DSS)
Digital Noise reduction (DNR)
Lens: fisheye, f=1.65 mm/F2.8
Built-in IR LED - 4 pcs.
Privacy zones: 5
1 alarm input and output
Built-in webserver: video and audio compression and real-time network transmission
Compression: H.264, M-JPEG
Video processing resolution: 4000 x 3000, 3840 x 2160 (4K Ultra HD), 3200 x 1800 (QHD+),
3072 x 2048, 1920 x 1080 (Full HD), 1280 x 1024 (SXGA), 1280 x 720 (HD), 1024 x 768 (XGA),
800 x 600 (SVGA), 720 x 576 (D1), 640 x 480 (VGA), 352 x 288 (CIF), 320 x 240 (QVGA)
4 streams: compression, resolution, speed and quality defined individually for all video streams
RTP/RTSP protocol support for video transmission
Network connection control and IP address check function
Pre- & post-alarm functions - video recording in AVI format
Schedule recording function
Hardware motion detection
Audio detection
Bidirectional audio transmission
Microphone and speaker built in
Micro micro SD/SDHC/SDXC card support
Diverse definition of system reactions to alarm events: e-mail with attachment, saving file on FTP
server, NAS, alarm output trigger, saving file on micro SD card, HTTP notification
Software: NMS (NOVUS MANAGEMENT SYSTEM) for video recording, live monitoring,
playback and remote IP devices administration
IK 10
Power supply: 12VDC, PoE (Power over Ethernet)
FOREWORD INFORMATION
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
6
1.2. NVIP-12DN7023V/IR-1Pspecification
FOREWORD INFORMATION
Image
Image Sensor 12 MPX CMOS sensor 1/1.7” SONY Exmor R STARVIS
Number of Effective Pixels 4072 (H) x 3046 (V)
Min. Illumination
0.1 lx/F2.8 - color mode (DSS),
0.01 lx/F2.8 - B/W mode (DSS),
0 lx (IR on) - B/W mode
Electronic Shutter auto/manual: 1/1 s ~ 1/10000 s
Digital Slow Shutter (DSS) up to 1 s
Wide Dynamic Range (WDR) yes
Digital Noise Reduction (DNR) 2D, 3D
Lens
Lens Type fisheye, f=1.65 mm/F2.8
Day/Night
Switching Type mechanical IR cut filter
Switching Mode auto, manual, time, external, light sensor, smart
Switching Level Adjustment yes
Switching Schedule yes
Visible Light Sensor yes
Network
Stream Resolution
4000 x 3000, 3840 x 2160 (4K Ultra HD), 3200 x 1800 (QHD+), 3072 x 2048, 1920 x 1080 (Full HD), 1280 x
1024 (SXGA), 1280 x 720 (HD), 1024 x 768 (XGA), 800 x 600 (SVGA), 720 x 576 (D1), 640 x 480 (VGA),
352 x 288 (CIF), 320 x 240 (QVGA)
Frame Rate
20 fps for 4000 x 3000,
30 fps for 3840 x 2160 (UHD),
60 fps for 1920 x 1080 (Full HD) and lower resolutions
Multistreaming Mode 4 streams
Video/Audio Compression H.264, MJPEG/G.711, G.726, AAC, LPCM
Number of Simultaneous Connections max. 10
Bandwidth 70 Mb/s in total
Network Protocols Support
HTTP, TCP/IP, IPv4/v6, UDP, HTTPS, Multicast, FTP, DHCP, DDNS, NTP, RTSP, RTP, UPnP, SNMP, QoS,
PPPoE
ONVIF Protocol Support Profile G (ONVIF 2.6)
Camera Configuration
from Internet Explorer browser
languages: Polish, English, Russian, and others
Compatible Software NMS
Other functions
Privacy Zones 5
Motion Detection yes
Audio Detection yes
Image Processing 90˚ image rotation, 180˚ image rotation, sharpening, mirror effect
Prealarm/Postalarm up to 3 s or 20 frames/up to 9999 s or 20 frames
System Reaction to Alarm Events
e-mail with attachment, saving file on FTP server, saving file on SD card, saving file on NAS server, alarm
output activation, HTTP notification
IR LED
LED Number 4
Range 5 m
Angle 95°
Interfaces
Audio Input/Output 1/1 built-in: microphone, speaker
Alarm Input/Output 1 (NO/NC)/1
Network Interface 1 x Ethernet - RJ-45 interface, 10/100/1000 Mbit/s
Memory Card Slot microSD
Installation parameters
Dimensions (mm) 117 (Ф) x 55 (H)
Weight 0.4 kg
Enclosure vandal proof IK10 impact rating aluminium, white
Power Supply PoE, 12 VDC
Power Consumption
8.1 W,
10 W (IR on)
Operating Temperature -10°C ~ 50°C
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
7
FOREWORD INFORMATION
1.3. Camera dimensions
All dimensions in mm
55
23.3
35.9
Ø 117.1
59
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
8
1.4. Package contents
After you open the package make sure that the following elements are inside:
IP camera
230 VAC / 12 VDC power supply
Accessories bag
Short version of user’s manual
CD containing manual and software
If any of this elements has been damaged during transport, pack all the elements back into the original
box and contact your supplier for further assistance.
CAUTION!
If the device was brought from a location with lower temperature, please wait until it reaches the
temperature of location it is currently in. Turning the device on immediately after bringing it
from a location with lower ambient temperature is forbidden, as the condensing water vapour
may cause short-circuits and damage the device as a result.
Before starting the device familiarize yourself with the description and the role of particular
inputs, outputs and adjusting elements that the device is equipped with.
1.4. Package contents
After you open the package make sure that the following elements are inside:
IP camera
Accessories bag
Short version of user’s manual
If any of this elements has been damaged during transport, pack all the elements back into the original
box and contact your supplier for further assistance.
CAUTION!
If the device was brought from a location with lower temperature, please wait until it reaches the
temperature of location it is currently in. Turning the device on immediately after bringing it
from a location with lower ambient temperature is forbidden, as the condensing water vapour
may cause short-circuits and damage the device as a result.
Before starting the device familiarize yourself with the description and the role of particular
inputs, outputs and adjusting elements that the device is equipped with.
FOREWORD INFORMATION
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
9
2. START-UP AND INITIAL IP CAMERA CONFIGURATION
2.1. Description of connectors and control tools
NVIP-12DN7023V/IR-1P
1. Power connector
Pin 1 - 12 VDC (+)
Pin 2 - 12 VDC (-)
2. Port Ethernet 1000 Mb/s (RJ-45 connector)
3. Micro SD/SDHC/SDXC card slot
4. Alarm and audio input/output connector block
5. Built-in microphone
6. Reset button (restoring hardware factory defaults)
7. Built-in speaker
8. Light sensor
9. Lens
START-UP AND INITIAL CAMERA CONFIGURATION
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
10
2.2. Connecting power supply to the camera
The camera is supplied by using RJ45 network socket. To run NOVUS IP camera you have to connect
ethernet cable between camera and network switch with PoE support (IEEE 802.3at) or use power
supply compatible with the camera. You can also use a power injector compatible with IEEE 802.3at
standard. Description of connectors is located in Chapter 2.1
Information:
Power supply adapter is not included. Please use power adapter with parameters specified in user’s
manual.
Caution:
In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge
protectors is advised. Any damages resulting from surges are not eligible for service repairs.
2.3. NVIP-12DN7023V/IR-1P mounting
To mount a camera please follow the instructions below:
1. Unscrew two screws (marked with arrows on the picture above) fastening the camera’s casing and
remove it.
2. Put the camera to a desired mounting location and use screw holes in its base as a template to mark
points for drilling. Drill the anchor and (if required) cable holes and fix the camera to mounting surface
using screws.
3. Bring the intended cables to the connectors of the camera and perform the necessary electrical
connections inside the camera.
4. Lead cables outside camera, put on the external casing and attach it using screws.
START-UP AND INITIAL CAMERA CONFIGURATION
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
11
2.4. Starting the IP camera
To run NOVUS IP camera you have to connect ethernet cable between camera and network switch.
To power it up you can connect it directly via power supply adapter with parameters compatible with
camera power supply specification. NVIP-12DN7023V/IR-1P camera can be also powered with PoE
(IEEE 802.3at ) compatible switch.
After connecting power supply green LED should light on. Initialization process is then started which
takes about 30 seconds. You can then proceed to connect to the camera via web browser.
If the connection is successfully established orange LED blinks with a frequency proportional to the
quantity of data sent. Connecting via web browser is then possible. If connection isn’t established (the
network cable is disconnected) green and orange LEDs aren't active, solid light means that network
connection is ok but camera doesn't receive or send any data, with possible PC network settings error.
The recommended way to start an IP camera and perform its configuration is a connection directly
to the network switch which is not connected to other devices. To obtain further information about
network configuration parameters (IP address, gateway, network mask, etc.) please contact your
network administrator.
Connection utilising network switch with PoE
Connection utilising external power supply and network switch
START-UP AND INITIAL CAMERA CONFIGURATION
Power supply and
network transmission
Computer
IP Camera
Network Switch PoE
Network transmission
IP Camera
Network transmission
Network Switch
Computer
Network transmission
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
12
Connection utilising external power supply directly to the computer
Information:
Power supply adapter is not included. Please use power adapter with parameters specified in user ‘s
manual.
Caution:
In order to provide protection against voltage surges/lightning strikes, usage of appropriate surge
protectors is advised. Any damages resulting from surges are not eligible for service repairs.
2.5. Initial configuration via the web browser
The default network settings for NVIP-7000 camera series are :
1. IP address= 192.168.1.200
2. Network mask - 255.255.255.0
3. Gateway - 192.168.1.1
4. User name - root
5. Password - pass
Knowing the camera’s IP address you need to appropriately set PC IP address, so the two devices can
operate in one network subnet ( e.g. for IP 192.168.1.1, appropriate address for the camera ranges from
192.168.1.2 to 192.168.1.254, for example 192.168.1.60). It is not allowed to set the same addresses for
camera and PC computer
You can either set a network configuration (IP address, gateway, net mask, etc.) of NOVUS IP camera
yourself or select DHCP mode (DHCP server is required in this method in target network) by using
web browser or by NMS software. When you use DHCP server check IP address lease and its linking
with camera MAC address to avoid changing or losing IP address during device operation or network/
DHCP server breakdown. You have to remember to use a new camera IP address after changing
network parameters.
After network setting configuration has been done, the camera can be connected to a target network.
START-UP AND INITIAL CAMERA CONFIGURATION
IP Camera
Network transmission - cross over cable
Computer
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
13
3. NETWORK CONNECTION UTILIZING WEB BROSWER
3.1. Minimum PC specification for web browser connections
1. CPU Intel Core i5 2.4 GHz or newer
2. RAM memory min. 4 GB
3. VGA card NVidia GeForce with 512 MB of RAM memory, or equivalent
4. OS Windows 7 / 8 / 8.1 / 10
5. Network card 100/1000 Mb/s
3.2. Connection with IP camera via the Internet Explorer
You have to enter camera IP address in the Internet Explorer address bar. If IP address is correct user
login window will be displayed:
Default user is root and default password is pass.
For safety reasons, it is recommended to change default user name and password.
When you first time log on to the camera, web browser will download the applet for displaying images
from the camera. Depending on the current Internet Explorer security settings it may be necessary to
accept an install ActiveX control. To do this, click the "Install" button on the security info bar, to
download from the camera and to install install.cab add-on, which runs the installer NVIP Viewer
applet.
NETWORK CONNECTION UTILIZING WEB BROWSER
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
14
In the following steps is needed to confirm the will to install add-on and start the installation of the
NVIPViewer:
After completing the installation and restart the browser may appear monit from security system for
permission to launch the add-on. You should allow it to run. Now installation is complete:
If the installation fails, changing security settings for the IE browser is required. In order to do that,
please choose: Tools > Internet options > Security tab > Custom level and:
Under Download unsigned ActiveX controls - select either Enable or Prompt
Under Initialize and script ActiveX controls not marked as safe - select Enable or Prompt
You can also add the camera’s IP address to “trusted zone” and set lowest security level for it.
In addition, when working in Windows Vista/7/8/10 the ActiveX applet may be blocked by Windows
Defender or User account control. In such case you should allow to run this applet, or simply disable
these functions.
NETWORK CONNECTION UTILIZING WEB BROWSER
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
15
3.3. Connection with IP camera via other browser eg. Mozilla Firefox, Safari )
It is also possible to connect to the camera using Mozilla Firefox, but this browser doesn't offer full
functionality of the camera, so the recommended browser is Internet Explorer.
The first run of the IP camera in browser is very similar to the IE version. After you type the correct IP
address you have to write correct username and password. The default user is root and password
is pass.
Next, blank screen is displayed. Then you have to install the missing Quick Time plug-in from site:
http://www.apple.com/quicktime/download/
Information:
In the case of Firefox web browser it is recommended to use 32-bit version and application Apple
QuickTime 7.7.7 version or earlier.
NETWORK CONNECTION UTILIZING WEB BROWSER
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
16
After downloading and running it, a window depicting installation of particular components is then
displayed. After proper installation pictures from the camera should become visible
NETWORK CONNECTION UTILIZING WEB BROWSER
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
17
4. WWW INTERFACE - WORKING WITH IP CAMERA
4.1. Displaying live video
1. Main tabs
Home - live view page
System - camera settings ( IP, recording, sending alarm messages, motion detection)
Streaming - streaming settings for audio and video
Camera - picture settings
Logoutlogout of the current user
2. Language selection
3. Video stream selection
4. Settings for live video
WWW INTERFACE - WORKING WITH IP CAMERA
1
2
3
4
5
- Display mode in web browser
- Full screen view
- Microphone - enable audio from microphone
- Speaker - enable audio sending to the camera
- Snapshot - saves the current frame in JPEG format
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
18
Caution: Video analysis is performed at the computer which is remotely connected with the
camera. Digital PTZ function, due to number of calculations required in video processing, may
cause general decrease in computing power and decrease in operating system performance,
depending on the PC hardware configuration.
6. Video streaming information.
Right mouse button click on the live screen view displays additional information about actual video
and audio transition parameters.
- Snapshot - saves the current frame in JPEG format
- Video Streaming pause/play button
- Web recording to AVI button
- Activates events defined in “System -> Events -> “Manual trigger” tab
- Enables/disables the “fisheye view”
- Enables / disables the “digital PTZ” mode. While in it, it’s possible to
move the picture by holding the left mouse button and dragging it along
the screen, which will in turn display a corresponding movement direction
indicator. Single LMB click on any part of the screen places it in the
middle of video window.
- Enables split-screen view displaying the image from the camera in the
form of two 180 degrees panoramic views
- Enables 2x2 screen view displaying the image from the camera in the
form of four independent observation sectors
- Enables displaying the image from the camera in the form 180 degrees
panoramic view (function available in the wall mount mode only)
- Enables split-screen view displaying the image from the camera in the
form of one 180 degrees panoramic view and two independent
observation sectors (function available in the wall mount mode only)
WWW INTERFACE - WORKING WITH IP CAMERA
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
19
5. CONNECTING ACCESSORIES
5.1 Description of connection Alarm and Audio I/O
Alarm output electric connections
The maximum load of the alarm output is : 0.1 A, 30 VDC/VAC
ELECTRIC CONNECTORS AND ACCESORIES
Description of alarm and audio input/output connector terminal is presented in the table
Output -
IP Camera
Output +
Indicator
power supply
Indicator
Alarm and audio input/
output connector terminal
Numbering connectors
sequence
Pin Number Description
1 Alarm Output +
2 Alarm Output -
3 Alarm Input +
4 Alarm Input -
5 Ground connection GND
6 Audio Output
7 Audio Input
NVIP-12DN7023V/IR-1P User’s manual ver.1.0 (short form)
All rights reserved © AAT Holding S.A.
20
Alarm input connections
Audio output connections
Audio input connections
ELECTRIC CONNECTORS AND ACCESORIES
Alarm
Input -
IP Camera
Alarm
Input +
Switch/sensor
Pin Number Description
5 Ground connection GND
For connecting external audio devices such as
speakers with an amplifier
6 Audio Output
Pin Number Description
5 Ground connection GND
For connecting external audio devices such as a
microphone
7 Audio Input
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Novus VIP-12DN7023V/IR-1P Instrukcja obsługi

Kategoria
Kamery ochrony
Typ
Instrukcja obsługi
Ten podręcznik jest również odpowiedni dla

w innych językach