Stanley SCS-46 JET Instrukcja obsługi

Petrol Chain saw

SCS-46 JET

GB

Original instructions

Übersetzung der Originalanleitung

Prijevod izvorne instrukcije

Vertaling van de oorspronkelijke gebruiksaanwijzing

Traduzione delle istruzioni originali

Traduction des instructions originales

Tłumaczenie oryginalnej instrukcji

D

HR

NL

I

F

PL

Originaaljuhend

Originalios naudojimo instrukcijos vertimas

Μετάφραση του πρωτοτύπου των οδηγιών χρήσης

EE

LT

GR

2

Manufactured under license by:

MATRIX GmbH • Postauer Straße 26 • D-84109 Wörth/Isar • www.matrix-direct.net

Stanley is a registered trademark of The Stanley Works or its afﬁliates and is used under license.

Hergestellt unter Lizenz durch:

MATRIX GmbH • Postauer Straße 26 • D-84109 Wörth/Isar • www.matrix-direct.net

Stanley ist eine eingetragene Marke der The Stanley Works oder ihren Partnern und wird unter Lizenz verwendet.

Proizvedeno pod licencom:

MATRIX GmbH • Postauer Straße 26 • D-84109 Wörth/Isar • www.matrix-direct.net

Stanley je registrirani zaštitni znak tvrtke Stanley radova ili njegove podružnice, a koristi se pod licencom.

Geproduceerd onder licentie door:

MATRIX GmbH • Postauer Straße 26 • D-84109 Wörth/Isar • www.matrix-direct.net

Stanley is een geregistreerd handelsmerk van The Stanley Works of zijn dochterbedrijven en wordt gebruikt onder

licentie.

Prodotto sotto licenza di:

MATRIX GmbH • Postauer Straße 26 • D-84109 Wörth/Isar • www.matrix-direct.net

Stanley is a registered trademark of The Stanley Works or its afﬁliates and is used under license.

Fabriqué sous licence par :

MATRIX GmbH • Postauer Straße 26 • D-84109 Wörth/Isar • www.matrix-direct.net

Stanley est une marque déposée de The Stanley Works ou de ses sociétés afﬁliées, qui est utilisée sous licence.

Wyprodukowano na licencji przez:

MATRIX GmbH • Postauer Straße 26 • D-84109 Wörth/Isar • www.matrix-direct.net

Stanley

on Stanley Worksin tai sen tytäryhtiöitten omistama rekisteröity tavaramerkki, ja sen käyttö on luvanvaraista.

GB

D

HR

NL

F

PL

I

Toodetud litsentsi alusel:

MATRIX GmbH·Postauer Straße·26 D-84109 Wörth/Isar·www.matrix-direct.net

Stanley® on The Stanley Worksi või selle sidusettevõtete registreeritud kaubamärk ning seda kasutatakse litsentsi

alusel.

Ražots ar licenci, ko:

MATRIX GmbH·Postauer Straße·26 D-84109 Wörth/Isar·www.matrix-direct.net

Stanley® ir reģistrģta preģu zģme Stenlija darbu vai tģs ﬁliģģu un tiek izmantota saskaģģ ar licenci.

EE

LT

Kατασκευάζεται κατόπιν άδειας από την Matrix:

MATRIX GmbH • Postauer Straße 26 • D-84109 Wörth/Isar • www.matrix-direct.net

Stanley

το σήμα STANLEY είναι κατοχυρωμένο και χρησημοποιείται κατόπιν άδειας από την MATRIX.

GR

3

52 4 121 1816 14 10

17

23

6 78

B1

B2

21 15 22 119 13 19

3

20

4

6

7

1 2

7

7 2 8 1

1

B3

B5

B7

B4

B6

B8

B9 B10

max.

2-3mm

5

B11

B13

B15

B17

B12

B14

B16

B18

7

4

13

12

20

17

6

B19

B21

B23

B20

B22

B24

B25 B26

18

7

B27

B29 B30

B31

B28

0,63 mm

5

8

Read the instruction manual

carefully before use.

Maintain a minimum distance of

15 m between the machine and

other persons during use.

Wear approved ear protectors,

head protection and goggles.

Wear non-slip, strong footwear.

Wear good quality, hard-wearing

gloves.

Wear good quality, hard-wearing

workwear.

The emissions are toxic and may

cause asphyxia.

IMPORTANT. Fire risk.

Petrol and petrol fumes are highly

inﬂammable.

Safety instructions and warnings

WARNING: Do not use the chain saw

in the rain or damp conditions. Protect

it from moisture.

Protect yourself from saw kickback.

Hold the chain

saw securely with both hands during

use.

Hold the chain saw with the

right hand on the rear handle

and your left hand on the front

handle.

The Chain brake is

DISENGAGED (chain can

move) when BRAKE LEVER IS

PULLED BACK AND LOCKED.

The Chain brake is ENGAGED (chain is stopped) when

brake lever is in forward position. You should not be able

to move chain.

Guaranteed sound power level L

WA

:

113 dB(A)

Gently press primer button often enough

that no more bubbles are visible (approx. 5-6

times).

113

Do not touch a hot silencer or

cylinder. You may get burned.

These parts get

extremely hot from

operation. When turned off they remain hot for a short

time.

G

B

5-6

9

This machine complies with the prescribed

safety regulations for petrol machines.

Read the instruction manual carefully

before you start the machine.

Incorrect use my result in personal injuries

and damage to property. Persons who are

not familiar with instruction manual must not be

allowed to use the machine, Keep the instruction

manual in a safe place.

Children and young people are not permitted to

use the machine.

Proper usage

This machine is designed exclusively for sawing

wood, for example tree trunks, branches, planks,

etc.

If it is used for any other purpose or if modiﬁcations are

made to it, the manufacturer cannot accept any liability.

Also refer to the safety instructions, the assembly

and operating instructions and also the general

accident prevention regulations.

Safety instructions

Do not start or use the petrol chainsaw near other

people or animals.

Do not use the machine if you are tired or

distracted or your reactions are impaired due

to the consumption of alcohol or medication.

Inattention can result in serious injuries.

Wear approved goggles.

Wear approved ear protectors.

Wear good quality gloves.

Wear good quality non-slip work shoes with

safety steel toe-caps. Never use the machine

when wearing sandals or barefoot.

Wear an approved safety helmet at all times when

carrying out forest clearance work.

Do not wear loose-ﬁtting clothing or jewellery.

Wear long trousers to protect your legs.

Wear a head cover if you have long hair.

Loose-ﬁtting clothing, jewellery and long hair

could be caught in moving parts.

Wear suitable, close-ﬁtting work clothing.

Keep your body parts and clothing away from the

chainsaw when you start the engine and whilst it

is running.

Ensure that you are standing on a ﬁrm, safe

surface whilst working. Do not walk backwards

carrying the machine to avoid stumbling. Do not

adopt unnatural postures.

If you use the petrol chainsaw for lengthy periods

of time, you may suffer circulation problems

caused by vibrations (white ﬁnger disease). It

is not possible to provide precise details on the

duration of use in each case since it may differ

from person to person. The following factors may

affect this phenomenon: Circulation problems in

the hands of the user, low outdoor temperatures

and lengthy periods of use. We therefore

recommend that you wear warm work gloves and

take regular breaks.

The emissions from engines are toxic and may

cause asphyxia. Do not start the petrol chainsaw

in enclosed or poorly ventilated areas.

Only ﬁll the fuel tank outdoors or in adequately

ventilated areas.

Petrol and petrol vapours are highly inﬂammable.

Keep it away from inﬂammable materials and

ignition sources, such as hot stoves or ovens.

Do not smoke whilst refuelling or using the

machine.

Dry up any spilled petrol immediately.

G

B

10

Only start the petrol chainsaw away from the

refuelling point.

Ensure that the cover on the tank is always well

sealed. Watch for possible leaks.

Do not open the tank cover or refuel the machine

whilst the engine is running or when the machine

is hot.

Open the tank cover slowly so that the petrol

vapours can escape.

Ensure that the handles are clean, dry and free of

the petrol mixture.

Do not use the machine without the exhaust. You

may suffer burns if you ignore this.

Use only the fuel recommended in this manual.

Only keep petrol in containers designed for this

purpose and in a safe place.

Switch off the machine before you put it down.

Only work in daylight or in good artiﬁcial light.

Conduct a visual inspection of the machine before use.

Check that all screws and connectors are tight.

Always hold the machine ﬁrmly in both hands.

Check the machine and its components and

safety equipment every time before use for signs

of damage and wear and have any repair work

carried out without delay. Never render protective

and safety equipment non-functional. Do not use

the machine if you discover signs of damage or

wear.

Do not overload the machine and do not use it for any

work for which it is not designed.

Ensure that the ventilation openings are always

free of dirt.

Keep the machine out of the reach of children.

Check the machine for signs of damage after any

collisions of other types of damage.

Use only the accessories recommended by the

manufacturer.

Only have the machine repaired by trained

personnel and using only genuine spare parts.

This will ensure that the safety of the machine is

maintained.

Do not use the chainsaw near inﬂammable liquids

or gases or in a wet or damp environment. If you

ignore this, there is a risk of ﬁre or explosion.

Never leave the machine running unattended.

Do not use the machine if you are tired or

distracted or your reactions are impaired due

to the consumption of alcohol or medication.

Inattention can result in serious injuries.

Only work in suitable light conditions.

You are responsible for safety in the area in which

you are working.

Keep tools clean and in good working order so

that they are easier and safer to work with.

Wear suitable work clothing such as gloves, safety

helmet, goggles or safety visors and long trousers

made of strong material.

Ensure that you are standing on a ﬁrm, safe

surface and wear good quality non-slip work

shoes. Never use the machine when wearing

sandals or barefoot.

Loose-ﬁtting clothing, jewellery and long hair

could be caught in moving parts.

Wear a head cover if you have long hair.

Do not wear loose-ﬁtting clothing or jewellery.

Ensure that you are standing on a ﬁrm, safe

surface whilst working. Do not walk backwards

carrying the machine to avoid stumbling. Do not

adopt unnatural postures.

G

B

11

Whilst working always keep the machine an

adequate distance from your body.

Always switch off the machine during breaks and

when changing location. Wait until the chainsaw

stops and switch off the engine.

Never leave the machine unattended at the

workplace. Store the machine in a safe place

during breaks.

Always switch off the machine when changing

location.

Personnel using the machine must not be

distracted. This may cause them to lose control of

the machine.

Never use the machine in rain, in wet or damp

environments and do not store it outdoors.

If the machine becomes wet, wait until it is fully

dry before using it again.

Protect the machine from rain and moisture.

Always hold the saw with two hands when the

engine is running.

Use the claw to position the saw for every cut and

always start every cut with the chain moving.

Complete the cut in such a way that the saw does

not become trapped in the wood.

Pay special attention to branches that are under

tension.

Only pull the machine out of the wood whilst the

chain is still moving.

Never saw using one hand over shoulder height.

Always stand perpendicular to the slope when

using the saw on a gradient.

Always stand to the side of falling trees.

Watch the falling direction of the sawn parts.

Never start a cut using the tip of the bar and never saw

using the tip of the bar – danger of recoil!

There is always a risk of recoil if the tip of the bar

touches wood or other objects. This makes the

chainsaw impossible to control and may lead to

it being catapulted with great force towards the

operator.

Always saw through one branch at a time.

Watch neighbouring branches when lopping

branches off a tree.

Never use the machine as a lever for moving

objects.

Always use the chain guard for transporting the

chainsaw.

Before use

Check the machine and chain to ensure that they

are in perfect working order and safe to use.

Check the function of the chain lubrication system and

the oil level. Check the chain tension and the function of

the chain brake.

Machine components (B1-B2)

1. Guide bar

2. Saw chain

3. Chain guard

4. Chain brake / Hand guard

5. Claw stop

6. Sprocket wheel cover

7. Guide bar bolts/screws

8. Chain adjustment screw

9. Front handle

10. Rear handle

11. Starter cable

12. Oil tank cover

13. Petrol tank cover

14. Safety trip

15. Spark plug wrench

16. Air ﬁlter cover

17. Choke lever

18. Control switch

19. Throttle lever

20. Oil discharge duct

21. Fuel mixing canister

G

B

12

correctly.

Important! The chain must not slip off the guide bar (1) .

the chain links must be positioned precisely between the

teeth of the sprocket wheel.

the chain adjustment tang on the sprocket wheel must

insert the hole on the guide bar.

- Now ﬁt the two guide bar screws (7) again. Only

tighten them by hand at this stage, however.

Tension the saw chain (B10-B11)

Ensure that the guide bar screws (7) for adjusting

the saw chain (2) are only hand tight. Undo them

if necessary.

- To increase the tension of the saw chain (2), turn

the chain adjustment screw (8) clockwise using a

suitable screwdriver.

- To reduce the tension of the saw chain (2), turn

the chain adjustment screw (8) anti-clockwise

using a suitable screwdriver.

The saw chain (2) tension is correct if it can be

raised a maximum of 2 - 3 mm in the centre of the

guide bar (1).

- Tighten the guide bar screws properly after you

have adjusted the saw chain.

Notes

Allow a new saw chain (2) to run for approx. 5

minutes before actually sawing with it. Check the

chain tension again after this time and adjust it if

necessary.

When it is warm, the saw chain (2) will expand

and may sag. This gives rise to the risk tat the saw

chain (2) will jump off the guide bar. Therefore

you must adjust the tension of the chain (2) after

it has carried out its ﬁrst sawing work.

Since a saw chain (2) that has been tensioned

22. Screwdriver

23. Primer button

Assembly (B3-B4)

The saw chain and chain guide bar are not supplied

ready-assembled.

To prevent injuries, wear gloves when ﬁtting the

saw chain, when tensioning the chain and during

the subsequent chain tension check.

Fit the guide bar

- First disconnect the chain brake. Press the hand

guard (4) towards the top handle for this purpose.

- Remove the sprocket wheel cover (6) by undoing the

two guide bar screws (7).

- Assemble the claw stop (5) according to the picture

above by using the spark plug wrench.(B31)

- Place the guide bar (1) with the notched end on

the two guide bar bolts (7).

Fit the saw chain

(B5-B9)

- Lay out the chain (2) in a loop. Ensure that the

cutting claws point in a clockwise direction.

- Push the chain (2) over the coupling on to the

sprocket wheel on the chainsaw. Ensure that the

chain links are positioned precisely between the

teeth of the sprocket wheel.

- Now place the chain (2) over the tip of the bar.

Ensure that the chain links are positioned in

the guide bar groove.

The saw chain will sag downwards at this time on

the bottom of the guide bar.

- Now ﬁt the sprocket wheel cover (6) again.

Ensure that the chain adjustment tang engages

in the hole on the guide bar. Only then will

it be possible to ﬁt the sprocket wheel cover (6)

G

B

13

Unscrew the oil tank cover (12). Fill the oil tank

with biologically degradable chain oil.

Never use recycled oil or used oil.

Ensure that no dirt gets into the oil tank.

The chainsaw must never be operated without

oil.

If the chainsaw is operated without oil, the entire

saw will suffer damage within a very short period

of time.

Check the oil level and the chain lubrication

system before every starting work.

Check the automatic function of the chain lubrication

system by holding the running saw with the tip of the

bar against a sheet of paper on the ground. Keep a safe

distance! If an increasing oil mark can be seen on the

paper, the automatic

lubrication system is working correctly when the saw

chain is running.

Always ensure that the oil discharge duct (20) is

free of dirt at all times. If necessary clean it with

a thin object (such as a toothpick or matchstick).

Caution:

Do not try to adjust the oil ﬂow of the oil pump. Because

it has been adjusted in the optimal position before it left

the factory.

Engine / Chain brake (B16)

This chainsaw is ﬁtted with an engine/chain brake

for your safety.

If the saw suffers recoil, the front hand guard (4)

will strike against your hand and trip the chain

brake. To restart the saw, pull the hand guard

forcefully backwards towards the front handle.

The chain will stop after a maximum of 0.1

second.

Carry out a function test from time to time

To do this, push the hand guard (4) forwards and

switch on the saw brieﬂy. The chain must not

start to move. Release the guard. Pull the hand

when warm will contract as it cools and this

would result in excessive chain tension, the chain

tension must be reduced after you have ﬁnished

the sawing work.

IMPORTANT – the tension of the chain (2) must be

checked several times over the course of a working day.

Always wear gloves for this work.

Since the guide bar (1) is subject to particularly

high stress at the return point and at the interface,

we recommend that the guide bar be turned

each time you sharpen the chain so as to avoid it

wearing on one side.

Fuel (B12)

Use only a mixture of unleaded regular petrol

and special 2-stroke engine oil in a mixing ratio

of 40:1.

Important: Do not use a different mixing ration

and do not use pure petrol.

Do not use fuel if it is more than 2-3 months old.

If you do not intend to use the machine for a

lengthy period, empty the tank and reﬁll it before

you start work again.

Mix petrol in a ratio of 40:1

- Add 4.0 litres of petrol to 100 ml of 2-stroke oil

in a fuel tank and mix the two components by

shaking the machine forcefully.

Fill the petrol tank

- Unscrew the petrol tank cover (13) slowly so

that the pressure and petrol vapours can escape

safely.

- Fill the tank with the 40:1 2-stroke mixture using

a funnel and screw the petrol tank cover (13) back

into place.

Chain lubrication (B13-B15)

The chainsaw is supplied without oil.

G

B

14

Stop the engine (B19)

- Allow the engine to slow down to idling speed

without any throttle.

- Move the control switch (18) downwards to

“STOP”.

Start when the engine is warm

- The procedure is identical for starting when the

engine is cold. However, in this case the choke

lever (17) remains fully pushed in.

Working with the chainsaw

Wear gloves, ear protectors, protective clothing

and a helmet with a visor.

Never saw above shoulder height.

Never saw with one hand.

Never saw on a ladder, in a tree or if you are not

standing on ﬁrm footing.

Check the following before starting the engine:

- Is the saw chain tension correct ?

- Is the oil tank full?

- is the chain brake released?

- Start the chainsaw.

Holding the saw (B20)

Hold the front handle (9) in your left hand and the

rear handle (10) in your right hand.

Switch off the saw

Release the throttle lever (19).

Set the control switch (18) to <<STOP>>). Do not

put down the chainsaw until the chain has stopped

moving.

Carburettor adjustment

The carburettor has been set at the factory to

provide the best possible performance. If you

guard towards your body. The chain will start

when the saw is switched on.

Machine instructions

Check the chainsaw at regular intervals for signs

of damage.

Ensure that all the parts work correctly and properly.

Please note that all parts must be ﬁtted correctly

in order to function properly.

Have damaged parts repaired immediately in an

after-sales workshop.

Start when the engine is cold (B17-B19)

- Place the petrol chainsaw safely on the ground.

- Move the control switch (18) upwards.

-Gently press primer button (23) often enough that no

more bubbles are visible (approx. 5-6 times).

- Pull the choke lever (17) out as far as possible.

- Adopt a safe posture.

- Hold the petrol chainsaw securely on the ground

using your left hand.

- Place your right foot in the shaft of the rear

handle (10).

- Pull the starter cable (11) out as far as possible 3

to 5 times.

- Choke level jumps back automatically when pressing

the trigger.

- Pull the starter cable (11) several times quickly

and forcefully right to the end of the cable until

the engine starts.

Warm up the engine for 30 seconds. Tighten and release

the trigger.

G

B

15

wish to improve the setting, contact an approved

workshop.

Storage

Clean the saw chain (2) and guide bar (1) after

every use.

Fit the chain guard (3).

Work instructions (B21-B27)

Obey all the safety regulations.

Never saw with a loose or blunt chain. Always pull

the machine out of the wood whilst the chain is

still moving.

When cutting fallen trees, please note that the

trunk may be under tension.

Trunk under tension on the top. The tree may

spring upwards.

Trunk under tension on the bottom. The tree may

spring downwards.

Use a clamp (for example a saw stool) whenever

possible.

Only use the saw for wood or wooden objects.

Watch for foreign bodies such as nails or stones.

If they come into contact with the moving saw

chain they may be catapulted out and may also

damage the saw chain.

When cutting wood, the claw stop (5) must be

positioned ﬁrmly against the wood and when the

saw is started it must move into the wood. Hold

the saw using the front handle and pull the saw

upwards using the rear handle. The claw stop can

be used as a pivot point for this purpose. To reset the

position of the claw, press gently on the front handle and

pull the saw backwards slightly.

Now place the claw stop a little deeper and then

pull the handle upwards again.

For longitudinal cuts, the chainsaw must be positioned at

as ﬂat an angle as possible. Since the claw stop cannot

be used in this case, take special care with these cuts.

Danger of recoil!

There is always a risk of recoil if the tip of the bar

touches wood or other objects. This makes the

chainsaw impossible to control and may lead to

it being catapulted with great force towards the

operator.

Whenever possible, always saw with the underside

of the bar since if you saw with the top of the bar, the

chainsaw will be catapulted towards the operator if the

chain jams.

Support yourself on the trunk whenever possible

when removing branches from a tree.

Special precautions for felling trees:

Felling trees is extremely dangerous and training

is required for this work. If you are unfamiliar with

this work, you should not attempt it. You must

receive training ﬁrst.

Never attempt to fell trees whose diameter is greater

than the length of the guide bar.

A falling tree may also bring down other trees.

Always use twice the tree length as a danger area

(felling area). Take care also not to disturb

power and telephone cables.

Before starting to fell a tree, you must plan and

clear an escape route. The escape route must be

in the opposite direction to the expected felling

direction.

There must be no spectators, animals or obstacles

in the felling area.

If the saw jams in the tree, never attempt to free it

when the engine is running. Use wooden wedges

to free the saw.

Taking into account the centre of gravity of the

crown and the wind direction, calculate the felling

direction ﬁrst. Ensure that the chainsaw is

running immediately before it comes into contact

G

B

16

Servicing and care (B28-B30)

Saw chain

Saw chain and guide bar servicing

Adjust the tension of the saw chain (2) from time

to time when necessary.

Turn the guide bar (1) after lengthy usage and

when you change the saw chain (2). This will compensate

the wear on the groove on the cutting side of the bar.

Sharpen the saw chain

The saw chain (2) should be serviced by a trained

specialist.

Air ﬁlter

After a lengthy period of use, you should clean

the air ﬁlter. Dust and pollen will block the pores

of the air ﬁlter.

- Remove the air ﬁlter cover (16) and wash

the air ﬁlter in mild soap suds. Important:

Do not use petrol or solvents.

- Dry the ﬁlter before you use it again.

A damaged air ﬁlter must be replaced straight

away so as not to reduce the service life of the

engine.

Use a damp cloth to clean the plastic parts. Do

not use cleaning products, solvents or sharp

objects.

Clear dust accumulations from the ventilation

openings and moving parts at regular intervals

using a soft brush.

After a lengthy period of use, remove the guide

bar and chain and clean them with a brush.

Spark plug adjustment

At least once a year or if the engine does not start

easily, check the electrode gap on the spark plug.

The correct gap between the lug and the contact

is 0.25“/0.63 mm.

with the wood. Saw a notch in the tree (A) in the

felling direction. This felling notch will guide the

tree and determine the direction in which it falls. Check

the felling direction again. In the event that you have to

correct the felling direction, recut the notch to extend it

to the full width of the trunk.

Shout “Timber”.

Now saw the felling cut (B) on the side of the tree

opposite the notch. Start this above the bottom

of the notch.

Place wedges in the felling cut promptly.

Leave a rupture strip (C). This acts as a hinge. If

you saw through the rupture strip, the tree will

fall out of control.

Never saw down trees, fell them using wedges.

Stand back when a tree falls. Check the crown

area. Wait until the crown stops shaking.

Never fell trees if you can no longer see all the

details in the felling area (because of rain, snow,

fog or twilight).

Never fell trees if you cannot control the felling

direction because of high winds.

Only fell trees if you have absolutely safe footing.

Lying trees or branches may be under tension.

Make a cut to relieve this tension ﬁrst, and

then the actual cut.

Caution: After operated the chain saw at full load for

a long time, should let the engine run at no load for a

while, until the cooling air takes away most of the heat.

In this way, it will avoid much more heat collected and

avoid causing the drive mechanism overheat.

After sawing work. Need to slacken the saw chain if it

is tensioned at working temperature. Because the saw

chain will be shrunk during cooling and it will damage

the crankshaft and the bearing if it is not slackened.

G

B

17

Weight ( Without guide bar and chain, empty tank):5,6 kg

Sound pressure level(L

PA

): 102,78 dB(A), K=2,5 dB(A)

Sound power lever(L

WA

): 110,07 dB(A), K=2,5 dB(A)

Vibration:

Max. front handle: 5.650 m/s

2

, K=1.5 m/s

2

Max. rear handle 6.072 m/s

2

, K=1.5 m/s

2

Length max. Bar: 16‘’

Chain pitch: 9,525 mm

Template chain: 1,27 mm (0,05")

Sprocket: 7 Teeth X 9,525 mm

Engine idling speed range:: 2700-3400 min

-1

Maximum speed: 11000 min

-1

Chain Type: Oregon 91P057X (for 16 ")

Guide Bar Type: Oregon 160SDEA095 (for 16 ")

The operating noise level may exceed 113 dB.

Repairs

Use only the accessory and spare parts recommended by

the manufacturer. If the machine suers a failure despite

our quality controls and your care, have repair work

carried out only by a trained electrician.

Environmental protection

Do not simply dispose of the machine,

accessories and packaging in the dustbin, but

ensure that it can be recycled. A small

amount of effort on your part can do a great

deal of good for our environment.

Residual risks

Even when properly used in the tool is always some

residual risk that can not be excluded. From the nature

and design of the tool, the following potential hazards

can be derived :

- Contact with the unprotected chain ( cuts);

- Reaching into the running saw chain (cut injury);

- Unexpected , sudden movement of the guide rail ( cuts);

- Ejection of parts of the chain;

- Ejection of parts of the material to be cut;

- Impairment of hearing , if there is no prescribed hearing

protection is worn;

- Inhalation of of material to be cut;

- Risk of kickback;

- This device produces an electromagnetic ﬁeld during

- Wait until the engine is completely cold.

- Remove the air ﬁlter cover.

- Take the spark plug cap off the spark

plug and unscrew the spark plug using a spark

plug wrench.

- If the electrode has suered excessive wear or

it is heavily encrusted, the spark plug must be

replaced with an equivalent one. Heavy encrustation on

the spark plug may be caused by too high an oil content

in the fuel mixture, poor oil quality, the petrol mixture

being too old or the air ﬁlter being blocked.

- Screw the spark plug fully into the thread by

hand (do not cross the thread).

- Now tighten the spark plug using a spark plug

wrench.

- If you use a torque wrench, the tightening

torque is 12-15 Nm.

- Now attach the spark plug cap correctly to the

spark plug.

Fit the air ﬁlter cover again.

Chain lubrication

the fuel can be checked through the sight glass on the

fuel tank.

Important: please ﬁll up the oil tank before refueling the

fuel tank every time.

Technical data

Air-cooled 2-stroke engine SPS1E43F3

Displacement: 45,1 cm

3

Max. engine power: 1,8 kW

Fuel tank capacity: 500 cm

3

Oil tank capacity: 240 cm

3

Cutting length: 360 mm

Spark plug:

L8RTF(NHSP LD); L8RTC (Torch) ;L8RTF(BOSCH)

G

B

18

Problem Possible cause Remedy

The engine cuts out. Incorrect carburettor setting The carburetor can be adjusted by a

professional.

or

please contact service center.

The engine starts but

delivers very little power.

Incorrect choke lever setting

Air ﬁlter dirty

Incorrect carburettor setting

Set it to

Remove the air ﬁlter, clean it with

soap suds, dry it and then ﬁt it again.

Have the carburettor adjusted by a

specialist.

The engine does not start or starts but

then cuts out again.

Incorrect starting procedure

Incorrect carburettor setting

Sooted spark plug

Follow the instructions in “Start when

the engine is cold”

Have the carburettor adjusted by a

specialist.

Clean the spark plug, correct the

electrode gap or replace the spark

plug.

The engine runs unevenly. Incorrect electrode gap on the

spark plug

Burned spark plug

Clean the spark plug, correct the

electrode gap (ideally 0.25”/0.63 mm)

or replace the spark plug.

Excessive smoke development. Incorrect carburettor setting

Incorrect fuel mixture

Have the carburettor adjusted by a

specialist.

Empty the tank, and reﬁll it with the

correct mixture: 2-stroke, ratio 40:1

operation ! This ﬁeld can interfere with active or passive

medical implants under certain circumstances!

To reduce the risk of serious or fatal injury , we

recommend persons with medical implants their

physician and the manufacturer of the medical implant

consulted before the instrument is used !

G

B

19

Halten Sie die Kettensäge mit

der rechten Hand am hinteren

Handgriff und mit der linken

Hand am vorderen Handgriff.

Die Kettenbremse ist

ENTKUPPELT (Kette kann

sich bewegen), wenn der

BREMSHEBEL NACH HINTEN

GEZOGEN UND ARRETIERT IST. Die Kettenbremse ist

EINGEKUPPELT (Kette ist arretiert), wenn der Bremshebel

nach vorne gezogen ist. Die Kette sollte sich dann nicht

bewegen lassen.

Vor Inbetriebnahme

Gebrauchsanleitung lesen!

Sicherheitshinweise und Warnungen

Während des Betriebs auf einen

Mindestabstand von 15 m zwischen

Maschine und anderen

Personen achten!

Zugelassenen Gehörschutz,

Kopfschutz und Schutzbrille

tragen!

Rutschfeste und widerstandsfähige

Schuhe tragen!

Gute und widerstandsfähige

Handschuhe tragen!

Gute und widerstandsfähige

Arbeitskleidung tragen!

Die entstehenden Abgase sind

giftig und wirken erstickend!

ACHTUNG Brandgefahr!

Benzin und Benzindämpfe sind

leicht entzündlich!

Das Gerät nicht bei Regen benutzen

oder dem Regen aussetzen.

Schützen Sie sich vor Rückschlägen der

Kettensäge. Halten Sie die Kettensäge

während des Gebrauchs mit beiden

Händen gut fest

Schallleistungspegel L

WA

:

113 dB(A)

Primerknopf so oft leicht drücken, bis

keine Blasen mehr zu sehen sind (ca. 5-6 ×).

113

Gefahr von schweren

Verbrennungen bei

der Berührung des heißen

Auspuffs oder des Zylinders,

denn diese Teile stehen beim Betrieb des Motors unter

hohen Temperaturen. Auch nach dem Ausschalten des

Geräts sind diese Komponenten noch eine Zeit lang heiß.

D

5-6

20

Dieses Gerät entspricht den vorgeschriebenen

Sicherheitsbestimmungen für Benzingeräte.

Lesen Sie die Gebrauchsanleitung aufmerksam

durch, bevor Sie das Gerät in Betrieb nehmen.

Ein unsachgemäßer Gebrauch kann zu Schäden

an Personen und Sachen führen. Personen, die

mit der Anleitung nicht vertraut sind, dürfen

das Gerät nicht bedienen. Bewahren Sie die

Gebrauchsanleitung sorgfältig auf.

Kindern und Jugendlichen ist die Benutzung des

Gerätes nicht gestattet.

Bestimmungsgemäße Verwendung

Die Säge ist ausschließlich zum sägen von Holz,

z.B. Holzstämme, Äste, Bretter usw. im privaten

Bereich bestimmt.. Die Säge ist nicht für gewerbliche

oder ähnliche Einsatzzwecke geeignet.Bei nicht

bestimmungsgemäßer Verwendung

sowie bei Veränderungen an der Maschine übernimmt

der Hersteller keinerlei Haftung.

Beachten Sie ebenso die Sicherheitshinweise, die

Montage- und Bedienungsanleitung sowie darüber

hinaus die allgemein geltenden Unfallverhütu

ngsvorschriften.

Sicherheitshinweise

Die Benzin-Kettensäge darf in der Nähe von

Personen oder Tieren weder gestartet noch

benutzt werden.

Verwenden Sie das Gerät nicht wenn Sie

müde oder unkonzentriert sind oder Ihre

Reaktionsfähigkeit durch Genuss von Alkohol

oder Medikamenten beeinträchtigt ist.

Unaufmerksamkeit kann zu ernsthaften

Verletzungen führen.

Verwenden Sie eine zugelassene Schutzbrille.

Verwenden Sie einen zugelassenen Gehörschutz.

Verwenden Sie gute Schutzhandschuhe.

Verwenden Sie gute rutschfeste Arbeitsschuhe

mit Sicherheitsstahlkappen. Arbeiten Sie mit dem

Gerät niemals mit Sandalen oder gar Barfuß.

Tragen Sie bei Ausforstungsarbeiten unbedingt

einen zugelassenen Schutzhelm und eventuell weitere

länderspeziﬁsch vorgeschriebene Schutzbekleidung.

Tragen Sie keine weite Kleidung oder Schmuck.

Tragen Sie lange Hosen zum Schutz Ihrer Beine.

Verwenden Sie bei langen Haaren eine

Kopfbedeckung.

Lockere Kleidung, Schmuck und lange Haare können von

sich bewegenden Teilen erfasst werden.

Tragen Sie geeignete feste, eng anliegende

Arbeitskleidung.

Halten Sie Körperteile und Kleidungsstücke fern

von der Kettensäge, wenn Sie den Motor anlassen

oder laufen lassen.

Achten Sie beim Arbeiten auf einen festen und

sicheren Stand. Vermeiden Sie es wegen der

Stolpergefahr, mit dem Gerät rückwärts zu gehen.

Vermeiden Sie abnormale Körperhaltungen.

Bei längerer Anwendung der Benzin-

Kettensäge kann es zu einer vibrationsbedingten

Durchblutungsstörung kommen

(Weißﬁngerkrankheit). Angaben über die Dauer der

Anwendung können in diesem Fall nicht gemacht

werden, da dies von Person zu Person unterschiedlich

sein kann. Folgende Faktoren können diese Erscheinung

beeinﬂussen:

Durchblutungsstörungen der Hände des

Bedieners, niedrige Außentemperaturen, lange

Anwendungszeiten. Deshalb wird empfohlen

warme Arbeitshandschuhe zu tragen und regelmäßige

Arbeitspausen einzulegen.

Die Abgase von Explosionsmotoren sind giftig

und können unter anderem zur Erstickung führen.

Die Benzin-Kettensäge darf in geschlossenen

oder schlecht belüfteten Räumen nicht in Betrieb

genommen werden.

Befüllen Sie den Kraftstofftank nur im Freien oder

in ausreichend belüfteten Bereichen.

Benzin und Benzindämpfe sind leicht entzündbar.

Halten Sie es fern von entﬂammbaren Materialien

und Zündquellen wie z.B. Öfen oder Herde.

Rauchen Sie nicht, während Sie das Gerät auftanken

oder betätigen.

Trocknen Sie eventuell verschüttetes Benzin sofort auf.

Starten Sie die Benzin-Kettensäge nur an einem

von der Auftankstelle entfernten Ort.

D

Strona jest ładowana ...

Stanley SCS-46 JET Instrukcja obsługi

Stanley SCS-46 JET Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty