Brother 2030 Instrukcja obsługi

BROTHER

™

TN 350

TONER CARTRIDGE

BROTHER

™

HL 2030 (TN 350)

CARTRIDGE REMANUFACTURING INSTRUCTIONS

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

Summit Technologies is a division of UniNet Imaging Inc.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

Absolute COLOR

®

• Absolute BLACK

®

• Unidrums

®

• Unirollers

®

• Uniparts

®

• Unicoatings

®

REMANUFACTURING THE BROTHER HL 2030 TONER CARTRIDGES • TN-350 (TN-2000 EUROPE)

Released in January 2005, the Brother HL-2030 printer engine is based on a new 20ppm, 1200 DPI laser engine. While it is similar to

previous Brother engines, there are differences. Beside physically looking different, the toner is also new. The first section of this article

covers the theory behind these cartridges. If you are already familiar with the pitfalls of the HL-1240 cartridges, there is nothing new in

the theory here. If you are not however, it would be best to read through this section. It may save you a few very frustrating hours.

At this point, there are not many machines released, but I’m sure more will follow. With a street price of $137.00 for the HL-2040, they

are fast becoming very popular. HL-2030, HL-2040, HL-2070N

So far, Brother has only released one cartridge for these machines, the TN-350. The TN-350 cartridge is rated for 2,500 pages at 5%. The

drum unit is new as well, Part # DR-350 (DR-2000 Europe). It will be covered in a future article.

One change for these cartridges is the presence of a flag gear that resets the printer. The starter cartridges that come with new printers

do not have this gear. We are working on new flag gears, but until they become available, the starter cartridges cannot be remanufac-

tured.

As with previous Brother cartridges, the waste toner is repelled out of the drum cartridge and picked up by the developer roller in the toner

cartridge and brought back into supply chamber. That is why there will always be a good amount of toner left in the supply chamber when

the cartridge is finished. This remaining toner MUST be completely removed from the supply chamber before adding new toner. Failure to

do this will cause back grounding. In addition to contaminating the toner cartridge, this will also contaminate the cleaning section of the

drum cartridge, which in turn will contaminate the toner cartridge again. The reasons for this are explained in the following cartridge the-

ory section.

The cleaning section of the drum cartridge consists of a "cleaning brush" and a recovery blade. The cleaning brush has two opposite

charges placed on it during the print cycle. The first attracts any remaining toner off the drum. The second repels the toner off the brush

back onto the drum where it then transfers back into the toner cartridge. This is all done in a timing sequence that does not interfere with

the printing process. If the cleaning brush becomes contaminated with bad toner that will not charge, the brush will not be able to clean

itself, and back grounding will occur. It seems to be the nature of contaminated toner that it will accept most of the charge to be cleaned

off the drum, but it will not accept the charge that would allow the brush to clean itself off at all. A properly working cleaning brush will at

any given time have only a small amount of toner on it. Once contaminated, toner will accumulate, which will only cause the problems to

get worse.

Since the developer roller actually contacts the drum, some toner is transferred back into the supply of the toner cartridge. Once you print

with a bad toner cartridge, the drum unit will become contaminated. Even when you change out the toner with a good properly recycled

or new OEM cartridge, the drum unit will transfer some of the bad toner back into the good toner cartridge, which will again cause back

grounding. Both cartridges will be contaminated again.

The remaining "toner" in the toner cartridge is just below the bare minimum that can maintain the proper charge level. When the change

toner light comes on, the toner will not charge up to the proper level and will cause the back grounding. As the toner cartridge reaches

the end of it's useful life, the printer senses the low charge level in the toner supply and will try to keep the charge level up. This constant

charging keeps an almost "empty" cartridge from back grounding. Once the printer cannot get the remaining toner up to the minimum

charge, the change toner light comes on. The cartridge at this point will still be printing properly. If you were to take that same cartridge

out of the machine for a few days, and then put it back in the printer with out doing anything to it, the cartridge will shade. This will hap-

pen because the charge level that the printer was trying so hard to keep up has dissipated out and the materials left can no longer accept

a proper charge.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

WHAT DOES THIS ALL MEAN?

1. Make sure that your cartridge technicians thoroughly clean out the supply chamber of the toner cartridge.

2. In the event that they forget, and you have a shading cartridge. The toner must be completely cleaned out again (do not use the toner

over!!), and NEW fresh toner MUST be installed.

3. The drum unit has to be taken apart and cleaned out with emphasis on the cleaning brush area. This is a very simple process but very

necessary once contaminated.

How to run test pages, Printer trouble shooting as well as common cartridge problems will be covered at the end of this article.

TOOLS REQUIRED

Toner approved vacuum

Phillips Head Screwdriver

Small Common Screwdriver

Needle nose pliers

REQUIRED SUPPLIES

Brother 2030 Black Toner (90g)

Lint free cotton cloths

Toner magnet cloths

White Lithium Grease

NOTES

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

UNINET IMAGING INC. • BROTHER HL 2030/TN 350 CARTRIDGE REMANUFACTURING INSTRUCTIONS

3. On the NON GEAR side of the developer roller, remove the

screw.

NOTES

1. Vacuum the exterior of the cartridge. 2. Remove the fill plug from the toner cartridge. Dump the

remaining toner and vacuum/blow out the cartridge. Make sure

that the gear area is clean. Leaving any toner in the teeth of the

gears may cause a tooth to be damaged and cause a clicking

noise. We have found it best to use compressed air to clean

them out, but to also keep one hand over the gears to protect

them.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

UNINET IMAGING INC. • BROTHER HL 2030/TN 350 CARTRIDGE REMANUFACTURING INSTRUCTIONS

5. On the GEAR SIDE, remove the three screws and cover plate. 6. A white flag gear will fall off as the plate is removed. This flag

resets the printer when the cartridge is installed.

New starter cartridges do not have this flag gear. Until they are

available, the starter cartridges cannot be remanufactured.

4. Locate the two tabs on the developer roller end plate and pry off.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

UNINET IMAGING INC. • BROTHER HL 2030/TN 350 CARTRIDGE REMANUFACTURING INSTRUCTIONS

7. Remove the black plastic spacer from the developer roller

shaft.

8. Remove the E-Ring, and small gear.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

9. Remove the developer roller. 10. Vacuum the doctor blade and foam feed roller clean. We do

not recommend that the doctor blade be removed and the devel-

oper roller felt seals will be disturbed. Once a new blade is avail-

able, great care will have to be taken not to tear the seals, caus-

ing a leak. The doctor blade can be easily cleaned by blowing the

excess toner off, and wiping down with a lint free cloth. Be very

careful not to leave any lint behind!

UNINET IMAGING INC. • BROTHER HL 2030/TN 350 CARTRIDGE REMANUFACTURING INSTRUCTIONS

11. Inspect the magnetic roller felts. If they are compressed,

(shiny) rough them up with a small screwdriver.

12. Clean the gears, making sure that they have no toner on

them. This is a good time to also check the gear shafts to make

sure there is enough grease. If the shafts appear dry, or the

grease is contaminated with toner, clean the shaft and inside of

the gear. Replace the grease with white lithium grease.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

13. Clean the developer roller with a lint free cloth. Do not use

any chemicals other than a dedicated cleaner for Brother rollers

to clean the roller. A dry clean cloth will work fine.

14. Re-install the developer roller long shaft side to the gear

side.

UNINET IMAGING INC. • BROTHER HL 2030/TN 350 CARTRIDGE REMANUFACTURING INSTRUCTIONS

15. Install the small outside end plate and screw on the non-gear side.

Make sure the clear plastic plug for the optical sensor is locked in the proper position.

16. Install the developer roller gear, c-ring, and black axle. Make sure all the other gears are meshing properly.

You may have to release the white spacer on the mag shaft to get the gear back on.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

UNINET IMAGING INC. • BROTHER HL 2030/TN 350 CARTRIDGE REMANUFACTURING INSTRUCTIONS

17. Set the flag gear, install the gear cover plate, and three screws.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

18. Fill the cartridge with Brother 2030 Black Toner. 19. Replace the fill plug. Wipe the cartridge down to remove any

remaining toner dust.

UNINET IMAGING INC. • BROTHER HL 2030/TN 350 CARTRIDGE REMANUFACTURING INSTRUCTIONS

20. Install the developer roller cover.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

TEST PAGES

1. To print a test page from these machines, first turn the machine off.

2. Press and hold the “GO” Button, and turn the printer back on.

3. All the LED’s will light up, and go off.

4. When the TONER LED comes on, release the “GO” button.

5. Press the “GO” Button again; the printer will print out the test page.

This can also be accomplished through the printer driver.

MACHINE TROUBLESHOOTING

These machines have 4 LED’s to indicate the status or various problems. We have listed some of the more common ones here:

1. Yellow Toner light blinking, Green READY Light on: Toner Low

2. Yellow Toner light On, READY light out: Toner out

3. Yellow Drum light blinking, Green READY Light on: Drum life over soon

4. All lights blinking: Service call needed.

When the GO button is pressed, a secondary set of errors will show.

1. TONER Yellow light on: Fuser error

2. DRUM Yellow light on: Laser error

3. TONER Yellow and PAPER Red lights on: Main Motor failure

4. PAPER Red light on: Engine PCB failure

NOTES

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

COMMON TONER CARTRIDGE PROBLEMS

As some problems can be caused by both the toner cartridge as well as the drum cartridge, we have listed both here.

BACK-GROUNDING: Toner cartridge and Drum cartridge; By far the most common problem with these cartridges, there are three major

common causes.

1. The first is contaminated toner. If the old toner in the toner cartridge was not fully cleaned out, a shaded background will result usual-

ly over the entire page. This can also be caused by a contaminated cleaning brush in the drum cartridge, which is directly related to a bad

toner cartridge. (See cartridge theory at the beginning of this article).

2. If the developer roller in the toner cartridge is worn, it will tend to pull too much toner, and back-grounding will result. This normally hap-

pens only on cartridges that have been recycled a few times. A normal roller will have a somewhat mottled look, and the texture should

be smooth. If the roller has lines, small cracks, or just doesn’t look right, don’t use it.

A dirty developer roller can also cause this. If the roller has a white or bluish coating, it must be cleaned. Be sure to use only a dedicated

Brother developer roller cleaner. Any other type of cleaner will probably react with the toner and cause another set of problems.

3. Another back-grounding issue can result from the toner being used. Not all aftermarket toners will work together. This is because there

is always a small amount of toner left on the drum cartridge cleaning brush. Most aftermarket toners will work over the OEM, but not all

will work over another aftermarket toner. If your cartridges work in house but background out in the field, it can be that the drum unit has

failed, or that another aftermarket toner was used previous to yours. Check with your vendor to make sure that your toner will work on top

of another (all) aftermarket brand(s).

DARK BLACK VERTICAL STREAKS: Drum cartridge; This is normally caused by either a dirty primary corona wire, or the blue corona wire

cleaner is not in its "home" position on the left side of the cartridge.

GRAY VERTICAL STREAKS: This is normally caused by a groove in the developer roller. If the roller has a groove worn in it, it must be either

replaced, or re-surfaced by a company that specializes in this.

LIGHT PRINT: Drum cartridge; Can be caused by a dirty or worn Transfer Roller. These rollers are located inside the cartridge. In our tests,

they should last at least 2 cycles.

BLACK OR WHITE HORIZONTAL LINES: Toner cartridge and Drum cartridge; Black lines normally appear when there is a build up of toner,

White when there is a dead spot, or contamination of the roller.

SOLID BLACK PAGES: Drum cartridge; Bad drum ground contact, probably from the drum axle shaft to the contact gear inside the drum.

PERFECTLY STRAIGHT THIN BLACK LINES DOWN THE PAGE: Drum cartridge; Scratched drum.

BLACK DOTS THAT REPEAT 4X/PAGE: Drum cartridge; Bad drum, or something is stuck to the drum surface.

Brother 2030 Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

Brother 2030 Instrukcja obsługi

w innych językach

Powiązane artykuły

Inne dokumenty