Minolta 5440 Instrukcja obsługi

MINOLTA

®

MAGICOLOR 5430 • 5440 • 5450

CARTRIDGE REMANUFACTURING INSTRUCTIONS

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

Absolute COLOR

®

• Absolute BLACK

®

• Unidrums

®

• Unirollers

®

• Uniparts

®

• Unicoatings

®

MINOLTA

®

MAGICOLOR 5430

COLOR LASER PRINTER WITH TONER CARTRIDGE

UNINET IMAGING INC. • MINOLTA

®

MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS

MINOLTA

®

MAGICOLOR 5430 TONER CARTRIDGE

SIDE VIEW WITH END CAP SHOWN

BACK VIEW OPPOSITE SIDE VIEW

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

UNINET IMAGING INC. • MINOLTA

®

MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS

SEPARATING THE CARTRIDGE

1. Locate the cartridge end cap of the cartridge.

Using a phillips screwdriver, remove the seven highlighted

screws that hold the cartridge together.

2. Cartridge separated. Set the drum unit and end cap aside.

We will now proceed to clean the toner hopper.

CLEANING THE TONER HOPPER

3. Locate the toner hopper fill plug.

4. Using a small flathead screwdriver, carefully remove the fill

plug by prying it off.

Empty any residual toner from the hopper and clean thoroughly

using compressed air.

Once clean, refill, apply plug, and set aside.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

UNINET IMAGING INC. • MINOLTA

®

MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS

SEPARATING THE DRUM UNIT

5. The drum unit (top) and developer unit (bottom) are joined

together.

6. Locate the gear train side of the drum unit.

Remove the OPC contact (highlighted).

Now remove the gear train directly behind it. Note the position-

ing of the gears. One of the gears is not removable.

7. After removing he gears, release the two screws that hold the

drum axle plate in place.

Release the compression spring that is connected to the devel-

oper unit beneath.

Slide the drum axle plate out.

8. Drum axle plate removed.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

UNINET IMAGING INC. • MINOLTA

®

MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS

9. Release the compression spring on the opposite side of the

drum unit (drive gear side).

Note: The compression springs are different, the longer spring is

connected to the gear train side of the drum and the small spring

is connected to the drive gear side.

10. Locate the developer roller drive gear just below the OPC.

Using a phillips screwdriver, release the screw that holds it in

place. Note: this is a metric screw and will not fit anywhere else.

11. Developer roller drive gear removed. 12. Now, return to the gear train side and locate the pin that hold

the drum unit and developer unit together. Pull the pin out using

a pair of pliers.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

UNINET IMAGING INC. • MINOLTA

®

MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS

15. Once the screw has been removed, turn the support counter

clockwise until it comes to a stop. This will unlock the support

and allow you to remove it completely.

16. Final position of drive gear support plate that can now be

removed.

13. Separate the two halves by first pulling out the developer

unit from where the pin was removed. Once it clears the waste

hopper section pull the two halves apart away from each other

as shown

DISASSEMBLING THE DRUM UNIT

14. Remove the OPC drive gear support by first releasing the

screw that holds the support plate in place.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

UNINET IMAGING INC. • MINOLTA

®

MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS

REMOVING THE CORONA WIRE ASSEMBLY

19. Remove the corona wire by pushing it towards the opening

on the gear train side. This will allow you to lift one side of it for

easy removal.

20. Corona wire assembly removed.

REMOVING THE OPC

17. Once the OPC drive gear support plate has been removed, it

will allow movement for the drum axle and will simplify the

removal of the OPC.

Note: the drum is secured on the axle with pressure. It will take

some force to remove.

18. Picture of OPC drum removed.

Note: It will not be necessary to remove the drum axle but it can

easily removed by angling the axle and pulling it out of its sup-

port.

Wipe the OPC using drum cleaning solution, cover, and set aside.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

1. PUSH IN

2. THEN PULL OUT

UNINET IMAGING INC. • MINOLTA

®

MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS

22. Remove the wiper blade in the manner shown.

CLEANING THE WASTE HOPPER

23. Hopper shown with wiper blade completely removed.

Dump the waste toner from the hopper and clean thoroughly

using compressed air.

Clean the wiper blade using a lint free cloth and apply padding

powder before installing.

Install the wiper blade following the previous removal steps in

reverse.

ASSEMBLING THE DRUM UNIT

24. Install the corona wire assembly via the gear train side first.

Insert the corona wire assembly through the opening, then slide

through the opposite side.

REMOVING THE WIPER BLADE

21. Remove the wiper blade by first disengaging the two screws

(shown) that hold it in place.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

UNINET IMAGING INC. • MINOLTA

®

MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS

25. Once the corona wire is aligned with the cartridge, Push it

with your finger tips until it is back into its original place.

INSTALLING THE OPC

26. Before inserting the OPC, make sure its gears are facing in

the correct position.

27. Install the OPC drive gear support as shown. 28. Rotate the support clockwise until it locks into place. Once it

locks it will need to be secured with its appropriate screw.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

UNINET IMAGING INC. • MINOLTA

®

MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS

29. Assemble the two halves by first inserting the drive gear.

30. Once that has been accomplished join the two halves and

insert the pin on the gear train side.

31. Install the developer roller drive gear and its appropriate

screw.

32. On the opposite side, install the support plate and fasten

with two screw as shown.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

UNINET IMAGING INC. • MINOLTA

®

MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS

33. Once the two halves are assembled, continue installing the gear train and springs as shown.

REMOVING THE OEM CHIP

34. Locate the OEM chip on the inner portion of the end cap

(shown). The chip has been fastened with a minimal amount of

pressure and can be removed without tools.

ALTERING THE CHIP HOLDER

35. Before installing the replacement chip, a small adjustment

will need to be made to the chip holder shown. Two groove pat-

terns need to be cut out to accommodate the new chip.

Using a small cutting knife, cut out the two patterns as indicated

in the illustration.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

BEFORE

AFTER

UNINET IMAGING INC. • MINOLTA

®

MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS

36. Aftermarket chip installed.

37. Install the drum contact as shown.

ASSEMBLING THE END CAP

38. Once the chip has been installed, you can proceed with

installing the inner section of the end cap.

39. Install the transfer tube as shown.

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

UNINET IMAGING INC. • MINOLTA

®

MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS

40. Install the outer end cap.

41. Secure the end cap with the seven screws.

NOTES

© 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only. UniNet Imaging does not guarantee or warrant downloaded information.

www.uninetimaging.com/technical.asp

11124 Washington Blvd., Culver City, California USA 90232 • Ph +1 310 280 9620 • Fx +1 310 280 0533 • techsupport2@uninetimaging.com

Minolta 5440 Instrukcja obsługi

Niniejsza instrukcja jest również odpowiednia dla

Minolta 5440 Instrukcja obsługi

w innych językach

Inne dokumenty