AMP Lighting AAL-1022-B-BZ Instrukcja instalacji

Typ
Instrukcja instalacji

Ten podręcznik jest również odpowiedni dla

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP
®
Low Voltage Landscape Lighting
AMP
®
G2 ControlPro Series
AAL-102X-4-B-BZ
AMP
®
G2 ControlPro Series
AAL-102X-4-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please contact
www.amplighting.com or call 1-813-978-3900.
Important Safety Instructions
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
[email protected] • 813.978.3900
Product Dimensions
–3–
1
Package Contents
A. (1) Fixture
B. (1) Stake
Install Stake
3.25”
1.75”
3.5”
2.5”
3”
1.75”
ControlPro
30
ControlPro
40
ControlPro
60
Board
Stake
Soil
Ground
Determine the desired location for
mounting the xture. Hammer the stake
into the ground until ange of stake is ush
to grade. To avoid damage to the stake,
place a board on top of the stake while
hammering.
NOTE: If the ground is hard and the stake
is difcult to install, make a crosscut in the
ground using a at shovel.
INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
3
2
AMP
®
G2 ControlPro Series
AAL-102X-4-B-BZ
Install Fixture to Stake
Wire Connection
Fixture
Stake
Pigtail
Clear away an area in the
ground at the wireway slot
on top of the stake. Lay the
luminaire pigtail into the
wireway slot and screw the
xture on to the stake. Tighten
until snug.
Wireway Slot
Strip both the leads from the luminaire pigtail. Using two wire connectors
(sold separately), connect the leads from the luminaire to the main supply
cable leads.
Pigtail
Main Supply Cable
Wire Connectors
[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
4
AMP
®
G2 ControlPro Series
AAL-102X-4-B-BZ
Remove Glare Guard
Install/Replace Optic
Loosen the set screw and
remove the glare guard from
the xture.
Glare
Guard
Set Screw
Fixture
5
Remove Fixture Lens
Loosen the xture lens and remove
it from the xture.
Fixture Lens
Fixture
6
Remove Fixture Lens
Optic
Screw
Fixture
Loosen the screws and remove the optic
from the xture.
Install the new optic in the xture and
reverse Step 3 - Step 1. Make sure that
you have the optic properly aligned over
the LED board before tightening down.
Improper alignment when tightening
the screws can cause the optic to break.
LED Board
INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
AMP
®
G2 ControlPro Series
AAL-102X-4-B-BZ
–6––6–
[email protected] • 813.978.3900
–7–
IS-AAL-102X-4-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2019, AMP
®
Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

AMP Lighting AAL-1022-B-BZ Instrukcja instalacji

Typ
Instrukcja instalacji
Ten podręcznik jest również odpowiedni dla

w innych językach