Motorola XTL446 Instrukcja obsługi

1

English

CONTENTS

PRODUCT SAFETY AND RF EXPOSURE

FOR PORTABLE TWO-WAY RADIOS

Information and Operational Instructions for

Occupational Use . . . . . . . . . . . . . . . . . . . . . . . . 2

Federal Communication Commission (FCC)

Regulations (US markets only) . . . . . . . . . . . . . . 3

RF Exposure Compliance and Control Guidelines

and Operating Instructions . . . . . . . . . . . . . . . . . . 4

Use of Communication Devices While Driving . . 5

Operational Warnings . . . . . . . . . . . . . . . . . . . . . 6

Operational Cautions . . . . . . . . . . . . . . . . . . . . . . 6

Charger Safety Instructions . . . . . . . . . . . . . . . . . 7

GETTING STARTED

Your New Radio . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Batteries and Battery Charging . . . . . . . . . . . . . . 8

Turning Your Radio On and Off . . . . . . . . . . . . . . 9

Setting the Battery Type . . . . . . . . . . . . . . . . . . . 9

Battery Meter and Battery Alert . . . . . . . . . . . . . . 9

Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

TALKING AND LISTENING

Talk Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Monitor/Signal Strength Indicator . . . . . . . . . . . 10

Setting the Volume . . . . . . . . . . . . . . . . . . . . . . 10

Simple Menu Mode . . . . . . . . . . . . . . . . . . . . . . 11

Selecting a Radio Channel . . . . . . . . . . . . . . . . 11

Interference Eliminator Code . . . . . . . . . . . . . . . 11

Keypad Tones . . . . . . . . . . . . . . . . . . . . . . . . . .11

Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Scan List Editing . . . . . . . . . . . . . . . . . . . . . . . .12

Voice Scrambling . . . . . . . . . . . . . . . . . . . . . . . . 12

Hands Free Use (VOX) . . . . . . . . . . . . . . . . . . .12

Vibrate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Auto Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Time-out Timer . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Keypad Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Restore Factory Defaults . . . . . . . . . . . . . . . . . . 14

ALERTS

Channel Busy Indicator . . . . . . . . . . . . . . . . . . .15

Call Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Talk Confirmation Tone . . . . . . . . . . . . . . . . . . . 15

FURTHER INFORMATION

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 16

Use and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Warranty Information . . . . . . . . . . . . . . . . . . . . . 18

Copyright Information . . . . . . . . . . . . . . . . . . . . . 18

APPROVED ACCESSORIES LIST

6864225V01_O_EN.fm Page 1 Thursday, September 16, 2004 3:50 PM

English

2

PRODUCT SAFETY AND RF EXPOSURE

FOR PORTABLE TWO-WAY RADIOS

The information provided in this document supersedes

information contained in user guides published prior to

February 2002.

RF Energy Exposure Awareness and Control

Information and Operational Instructions for

Occupational Use

Note: This radio is intended for use in occupational/

controlled conditions where users have full

knowledge of their exposure and can exercise

control over their exposure to meet the

occupational limits in FCC/ICNIRP and

International standards. This radio device is

NOT authorized for general population

consumer use

This two-way radio uses electromagnetic energy in the

radio frequency (RF) spectrum to provide

communications between two or more users over a

distance. It uses radio frequency (RF) energy or radio

waves to send and receive calls. RF energy is one form

of electromagnetic energy. Other forms include, but are

not limited to, sunlight and

x-rays. RF energy, however, should not be confused

with these other forms of electromagnetic energy,

which when used improperly, can cause biological

damage. Very high levels of x-rays, for example, can

damage tissues and genetic material.

Experts in science, engineering, medicine, health, and

industry work with organizations to develop standards

for safe exposure to RF energy. These standards

provide recommended levels of RF exposure for both

workers and the general public. These recommended

RF exposure levels include substantial margins of

protection.

All Motorola two-way radios are designed,

manufactured, and tested to ensure they meet

government-established RF exposure levels. In

addition, manufacturers also recommend specific

operating instructions to users of two-way radios.

BEFORE USING THIS RADIO, READ

THIS BOOKLET WHICH CONTAINS

IMPORTANT OPERATING

INSTRUCTIONS FOR SAFE USAGE AND

RF ENERGY AWARENESS AND

CONTROL INFORMATION AND OPERATIONAL

INSTRUCTIONS FOR COMPLIANCE WITH RF

ENERGY EXPOSURE LIMITS IN APPLICABLE

NATIONAL AND INTERNATIONAL STANDARDS.

ALSO READ THE OPERATIONAL INSTRUCTIONS

FOR SAFE USAGE.

!

C a u t i o n

6864225V01_O_EN.fm Page 2 Thursday, September 16, 2004 3:50 PM

3

English

These instructions are important because they inform

users about RF energy exposure and provide simple

procedures on how to control it.

Please refer to the following websites for more

information on what RF energy exposure is and how to

control your exposure to assure compliance with

established RF exposure limits:

http://www.fcc.gov/oet/rfsafety/rf-faqs.html

http://www.osha.gov/SLTC/radiofrequencyradiation/

index.html

Federal Communication Commission (FCC)

Regulations (US markets only)

The FCC rules require manufacturers to comply with

the FCC RF energy exposure limits for portable two-

way radios before they can be marketed in the U.S.

When two-way radios are used as a consequence of

employment, the FCC requires users to be fully aware

of and able to control their exposure to meet

occupational requirements. Exposure awareness can

be facilitated by the use of a product label directing

users to specific user awareness information. Your

Motorola two-way radio has a RF Exposure Product

Label.

Do not remove this RF Exposure Label from

the device.

Also, your Motorola user manual, or

separate safety booklet includes information and

operating instructions required to control your RF

exposure and to satisfy compliance requirements.

Compliance with RF Exposure Standards

Your Motorola two-way radio is designed and tested to

comply with a number of national and International

standards and guidelines (listed below) for human

exposure to radio frequency electromagnetic energy.

This radio complies with the IEEE (FCC) and

ICNIRP exposure limits for occupational/controlled

RF exposure environments at operating duty

factors of up to 50% talk-50% listen and is

authorized by the IEEE/ICNIRP for occupational

use only.

In terms of measuring RF energy for compliance with

these exposure guidelines, your radio generates

measurable RF energy only while it is transmitting

(during talking), not when it is receiving (listening)

or in standby mode.

Note: The approved batteries, supplied with this radio,

are rated for a 5-5-90 duty cycle (5% talk–5%

listen–90% standby), even though this radio

complies with IEEE/ICNIRP occupational

exposure limits at usage factors of up to 50%

talk.

Your Motorola two-way radio complies with the

following RF energy exposure standards and

guidelines:

• United States Federal Communications Commission,

Code of Federal Regulations; 47 CFR part 2 sub-part J

• American National Standards Institute (ANSI) / Institute

of Electrical and Electronic Engineers (IEEE) C95. 1-

1992

• Institute of Electrical and Electronic Engineers (IEEE)

C95.1-1999 Edition

• International Commission on Non-Ionizing Radiation

Protection (ICNIRP) 1998

• Ministry of Health (Canada) Safety Code 6. Limits of

Human Exposure to Radiofrequency Electromagnetic

Fields in the Frequency Range from 3 kHz to 300 GHz,

1999

• Australian Communications Authority

Radiocommunications (Electromagnetic Radiation –

Human Exposure) Standard, 2003

6864225V01_O_EN.fm Page 3 Thursday, September 16, 2004 3:50 PM

English

4

• ANATEL ANNEX to Resolution No. 303 of July 2, 2002

"Regulation of limitation of exposure to electrical,

magnetic and electromagnetic fields in the radio

frequency range between 9 KHz and 300 GHz" and

"Attachment to resolution # 303 from July 2, 2002"

RF Exposure Compliance and Control

Guidelines and Operating Instructions

To control your exposure and ensure compliance with

the occupational/controlled environment exposure

limits, always adhere to the following procedures:

Guidelines:

• User awareness instructions should accompany device

when transferred to other users.

• Do not use this device if the operational requirements

described herein are not met.

Operating Instructions

• Transmit no more than the rated duty factor of 50% of

the time. To transmit (talk), push the Push-To-Talk (PTT)

button. To receive calls, release the PTT button.

Transmitting 50% of the time, or less, is important

because this radio generates measurable RF energy

exposure only when transmitting (in terms of measuring

for standards compliance).

•

When worn on the body, always place the radio in a

Motorola-approved clip, holder, holster, case, or body

harness for this product. Using approved body-worn

accessories is important because the use of

non-Motorola-approved accessories may result in

exposure levels, which exceed the IEEE/ICNIRP

occupational/controlled environment RF exposure

limits.

• If you are not using a body-worn accessory and are not

using the radio in the intended use position, in front of

the face in the hand held mode, then ensure the

antenna and the radio are kept 2.5 cm (one inch) from

the body when transmitting.

Keeping the radio at a

proper distance is important because RF exposures

decrease with increasing distance from the antenna.

• Hold the radio in a vertical position in

front of the face with the microphone

(and other parts of the radio including

the antenna) at least 2.5 cm (one inch)

away from the nose or lips. Antenna

should be kept away from the eye.

Keeping the radio at a proper distance is important

since RF exposures decrease with increasing

distance from the antenna.

Approved Accessories

• Use only Motorola-approved supplied or replacement

antennas, batteries, and accessories. Use of non–

Motorola - approved antennas, batteries and

accessories may exceed IEEE/ICNIRP RF exposure

guidelines.

For a list of Motorola-approved antennas, batteries, and

other accessories please see your dealer or local

Motorola contact. Your nearest dealer can be found at

the following web site:

http://www.motorola.com/cgiss/emea/

dealerlocator.html

Additional Information

For additional information on exposure requirements or

other training information, visit:

http://www.motorola.com/rfhealth.

6864225V01_O_EN.fm Page 4 Thursday, September 16, 2004 3:50 PM

5

English

Electromagnetic Interference/Compatibility

Note: Nearly every electronic device is susceptible to

electromagnetic interference (EMI) if

inadequately shielded, designed or otherwise

configured for electromagnetic compatibility.

Facilities

To avoid electromagnetic interference and/or

compatibility conflicts, turn off your radio in any facility

where posted notices instruct you to do so. Hospitals

or health care facilities may be using equipment that is

sensitive to external RF energy.

Aircraft

When instructed to do so, turn off your radio when on

board an aircraft. Any use of a radio must be in

accordance with applicable regulations per airline crew

instructions.

Medical Devices

Pacemakers

The Advanced Medical Technology Association

(AdvaMed) recommends that a minimum separation of

15 cms (6 inches) be maintained between a handheld

wireless radio and a pacemaker.These

recommendations are consistent with those of the U.S.

Food and Drug Administration.

Persons with pacemakers should:

• ALWAYS keep the radio more than 15 cms from their

pacemaker when the radio is turned ON.

• Not carry the radio in the breast pocket.

• Use the ear opposite the pacemaker to minimize the

potential for interference.

• Turn the radio OFF immediately if you have any reason

to suspect that interference is taking place.

Hearing Aids

Some digital wireless radios may interfere with some

hearing aids. In the event of such interference, you may

want to consult your hearing aid manufacturer to

discuss alternatives.

Other Medical Devices

If you use any other personal medical device, consult

the manufacturer of your device to determine if it is

adequately shielded from RF energy. Your physician

may be able to assist you in obtaining this information.

Use of Communication Devices While

Driving

Always check the laws and regulations on the use of

radios in the areas where you drive.

• Give full attention to driving and to the road.

• Use hands-free operation, if available.

• Pull off the road and park before making or answering a

call, if driving conditions or regulations so require.

6864225V01_O_EN.fm Page 5 Thursday, September 16, 2004 3:50 PM

English

6

OPERATIONAL WARNINGS

For Vehicles With Air Bags

Refer to vehicle manufacturer's manual prior to

installation of electronic equipment to avoid

interference with air bag wiring.

Do not place a portable radio in the area over an air bag

or in the air bag deployment area. Air bags inflate with

great force. If a portable radio is placed in the air bag

deployment area and the air bag inflates, the radio may

be propelled with great force and cause serious injury

to occupants of the vehicle.

Potentially Explosive Atmospheres

(Explosive atmospheres refers to hazard classified

locations that may contain hazardous gas, vapors,

or dusts.)

Turn off your radio prior to entering any area with a

potentially explosive atmosphere, unless it is a radio

type especially qualified for use in such areas as

"Intrinsically Safe" (for example, Factory Mutual, CSA,

UL, CENELEC or ATEX Approved). Do not remove,

install, or charge batteries in such areas. Sparks in a

potentially explosive atmosphere can cause an

explosion or fire resulting in bodily injury or even death.

The areas with potentially explosive atmospheres

referred to above include fuelling areas such as below

decks on boats, fuel or chemical transfer or storage

facilities, areas where the air contains chemicals or

particles, such as grain, dust or metal powders. Areas

with potentially explosive atmospheres are often but

not always posted.

Blasting Caps And Blasting Areas

To avoid possible interference with blasting operations,

turn off your radio when you are near electrical blasting

caps, in a blasting area, or in areas posted:

"Turn off two-way radio". Obey all signs and

instructions.

OPERATIONAL CAUTIONS

Antennas

Do not use any portable radio that has a damaged

antenna. If a damaged antenna comes into contact with

your skin, a minor burn can result.

Batteries

All batteries can cause property damage and/or bodily

injury such as burns if a conductive material such as

jewellery, keys, or beaded chains touch exposed

terminals. The conductive material may complete an

electrical circuit (short circuit) and become quite hot.

Exercise care in handling any charged battery,

particularly when placing it inside a pocket, purse, or

other container with metal objects.

!

W A R N I N G

!

C a u t i o n

6864225V01_O_EN.fm Page 6 Thursday, September 16, 2004 3:50 PM

7

English

Charger Safety Instructions

Before using the battery charger, read all instructions

and cautionary markings on:

• the battery

• the battery charger, and

• the radio using the battery.

To reduce the risk of injury, only charge the

Motorola approved rechargeable battery for this

product. Other types of batteries may burst,

causing personal injury and damage.

SAVE THESE INSTRUCTIONS

1.Do not expose the charger to rain or snow.

2.Do not operate or disassemble the charger if it has

received a sharp blow, or has been dropped or dam-

aged in any way.

3.Never alter the AC cord or plug provided with the

unit. If the plug will not fit the AC outlet, have the

proper outlet installed by a qualified electrician. An

improper condition can result in a risk of electric

shock.

4.To reduce the risk of damage to the cord or plug, pull

the plug rather than the cord when disconnecting the

charger from the AC outlet

5.To reduce the risk of electric shock, unplug the

charger from the AC outlet before attempting any

maintenance or cleaning.

6.Use of an attachment not recommended or sold by

Motorola may result in a risk of fire, electric shock, or

personal injury.

7.Make sure the cord is located so it will not be

stepped on, tripped over, or subjected to damage or

stress.

8.An extension cord should not be used unless abso-

lutely necessary. Use of an improper extension cord

could result in a risk of fire and/or electric shock. If

an extension cord must be used, make sure:

• That the pins on the plug of the extension cord are the

same number, size, and shape as those on the plug of the

charger.

• That the extension cord is properly wired and in good

electrical condition, and

• That the cord size is 18 AWG (1 mm

2

) for lengths up to

100 feet (30 metres) and 16 AWG (1.3 mm

2

) for lengths

up to 150 feet (45 metres).

9.The supply cord of this charger cannot be replaced.

If the cord is damaged please return to your place

of purchase.

!

C a u t i o n

6864225V01_O_EN.fm Page 7 Thursday, September 16, 2004 3:50 PM

English

8

GETTING STARTED

PUSH

TALK

TO

MENU

Use

j

to:

• Turn radio on/off

Use

k

to:

• Transmit call tone

Use

H

to:

• Scroll through menus

• Lock and unlock the keypad

(when held down and not in a

menu)

LED Indicator Light

Use

G

to:

• Talk

• Save a setting

Accessory Jack

Use

J

to:

• Monitor channel activity

• Scan

Use

l

and

D

to:

• Adjust volume

Microphone

Speaker

Use

C

to

:

• Backlight the LCD

6864225V01_O_EN.fm Page 8 Thursday, September 16, 2004 3:50 PM

9

English

Your New Radio

The Motorola XTL446 two-way radio operates on

PMR446 frequencies, and can be used in any country

where PMR446 frequencies are authorized, subject to

applicable regulations. This license-free, two-way radio

service is for family and group recreational use. Use of

this radio outside the country where it was intended to

be distributed is subject to government regulations and

may be prohibited. Read this manual carefully and

make sure you know how to operate the radio properly

before use.

Please retain your original dated sales receipt for your

records. For warranty service of your Motorola two-way

radio you will need to provide a copy of your dated

sales receipt to confirm warranty status.

Batteries and Battery Charging

The XTL446 radio operates with 3 AA Alkaline batteries

or a Nickel -Metal Hydride (NiMH) rechargeable battery

pack. A rechargeable upgrade kit can be purchased

separately from your supplier.

Caution: Do not disassemble the (NiMH) battery

pack.

Note: Remove batteries before storing your radio for

extended periods. Batteries corrode over time

and may cause permanent damage to your

radio. Exercise caution when handling batteries

that are leaking. Dispose of exhausted batteries

at a designated battery disposal unit and not in

the household waste.

Installing the Batteries

1.Turn off the radio if

necessary, by pressing

j.

2.Push latch up on back

cover.

3.Lift back cover off.

4.Insert 3 AA batteries as

shown by the markings

inside the battery compart-

ment. Alternatively insert the NiMH pack so that the

charge contacts are facing outwards to connect with

contacts on the battery cover.

5.Reposition battery cover and press down until it

clicks into place.

Charging the NiMH Battery

The NiMH battery can be charged while in the radio or

on its own in the charger adaptor cover. Charge the

NiMH battery overnight (16 hours) before using it for

the first time. Subsequent charges will only require four

hours of charging time.

1.Turn the radio off or place the NiMH battery in the

charger adaptor cover.

2.Plug the charger into an AC wall socket.

6864225V01_O_EN.fm Page 9 Thursday, September 16, 2004 3:50 PM

English

10

3.Position the charger connector with the large hook

over the large slot to the right of the three battery

contacts.

4.Place the small hook on the other end of the charger

connector over the small slot and snap it into place.

5.The solid red light indicator shows that NiMH battery

is charging and will flash green when the battery is

approximately 90% charged. The green light will be

illuminated constantly when the battery is fully

charged

6.To remove the adapter connector after charging,

push the large hook on the end of adapter connector

lightly, and then pull the small hook up.

Turning Your Radio On and Off

1.Press and hold j to turn your radio on.

2.The radio chirps and the display temporarily displays

every image. The red light above

j flashes every

three seconds. The display will show the channel

number 1-8, the interference eliminator code 0--

38 and the battery meter.

3.Press

j again to turn your radio off.

Setting the Battery Type

This feature allows the battery meter to recognize and

display the power usage for either alkaline or

rechargeable batteries.

1.Press

j to turn the radio on.

2.Press

H until the battery meter symbol c is

displayed.

3.Press

l or D to select either A (alkaline) or n

(NiMH).

4.Press

G to set.

Battery Meter and Battery Alert

The battery meter located in the top left hand corner of

the display indicates how much battery power you have

remaining. The radio will power off when the voltage

drops below a predetermined level, to protect the

rechargeable battery. When the battery meter displays

c, the radio chirps every 10 minutes.

Battery Life

The approximate (typical) battery life for:

• AA Alkaline batteries is 35 hours

• NiMH batteries is 12 hours

This is based on a 5% transmit, 5% receive and 90%

standby cycle.

Note: Battery life will be reduced if you regularly use

Hands-Free (VOX) accessories.

Belt Clip

Your radio comes with a swivel belt

clip.

1.To attach, align belt clip post with

hole in the radio back and gently

push until it clicks into place.

2.To remove, push release tab on top

of belt clip down to release catch

and pull belt clip from the radio

back.

O

6864225V01_O_EN.fm Page 10 Thursday, September 16, 2004 3:50 PM

11

English

TALKING AND LISTENING

Your radio has 8 channels and 38 interference

eliminator codes. If you are in a group and you wish to

talk to each other, all radios must be set to the same

channel and code. If you experience interference and

need to change channel, ensure that you change the

channel and code of all radios in your group.

1.For maximum clarity, hold radio 5 to 7 centimetres

from mouth.

2.Press and hold

G and speak into the micro-

phone. The LED indicator light glows continuously

when transmitting.

3.To receive messages, release

G.

Talk Range

Your radio has been designed to maximize

performance and improve transmission range in the

field. It is recommended that you do not use the radios

closer than 1.5 meters apart, to avoid interference.

Talk range depends on the terrain. It will be affected by

concrete structures, heavy foliage and by operating

radios indoors or in vehicles.

Optimal range occurs in flat, open areas, with up to 5

kilometres of coverage. Medium range occurs when

buildings and trees are in the way. Minimal range

occurs when dense foliage and mountains obstruct the

communication path.

Monitor/Signal Strength Indicator

It is good radio etiquette to monitor the channel for

activity before you transmit, to ensure that you do not

interrupt other users already on the channel. Pressing

and holding

J allows you to monitor your channel for

activity. If you hear static, the channel is clear for use.

This button can also help you determine when a radio

is moving out of range by displaying a receive signal

strength value next to the w while you press and hold

J. This value from 1 (weakest) to 6 (strongest)

indicates the relative signal strength of the incoming

signal.

Note: Obstacles that block the signal path may affect

the strength of the incoming signal.

Setting the Volume

1.Press D to increase or l to decrease the vol-

ume. The display will show V and the volume set-

ting (1-20).

2.Press

G to set.

Optimal Range

Outdoors

Medium Range

Outdoors

Minimal Range

Outdoors

Flat, open areas Buildings or trees.

Also near

residential

buildings

Dense foliage or

mountains. Also

inside some

buildings

6864225V01_O_EN.fm Page 11 Thursday, September 16, 2004 3:50 PM

English

12

Simple Menu Mode

Simple Menu mode allows you to limit the number of

menus displayed (Channel, Code and call tones) to

allow for simpler radio operation.

1.To enable Simple Menu mode press

H as you turn

on the radio. The radio chirps and the display tempo-

rarily displays only 6 images.

2.To turn off Simple Menu mode press

H as you

turn on the radio.

Selecting a Radio Channel

1.Press H. The channel number will begin to flash.

2.Use

D or l to change channel.

3.Briefly press

G to set new channel or press and

hold

H for 3 seconds to exit menu.

Interference Eliminator Code

Interference eliminator codes help minimize

interference by providing you with a choice of code

combinations.You can specify a different code for each

channel.

1.Press

H until the code number begins to flash.

2.Use

D or l to change the code.To hear every-

one on your channel, select code 0.

3.Press

G to set new code.

You can specify a different code for each channel:

1.To set a channel and code combination, press

H

and then press

D or l to select the channel.

2.Press

H again and then press D or l to

select a code.

3.Press

Gor press and hold H to exit the menu

and to save the channel and code combination.

Keypad Tones

Every time you press a button on your radio, it beeps

unless you turn this function off. Your radio is

programmed at the factory with keypad tones turned

on.

1.To disable the tones, hold down

l while switching

on your radio. When you press any button on the

keypad you will no longer hear the tone.

2.To enable tones, hold down

l while switching on

your radio.

Scan

Use this facility to monitor other transmitting radios. It

allows you to listen and talk back without having to

change channels.

1.To start scanning, briefly press

J. The scan indica-

tor h will be displayed and the radio scrolls through

available channels. When the radio detects activity, it

stops on that channel and displays the channel num-

ber and code.

6864225V01_O_EN.fm Page 12 Thursday, September 16, 2004 3:50 PM

13

English

2.To respond to the transmission, press G.If no

transmission occurs within five seconds, scanning

will resume.

3.To resume scanning for the next active channel

briefly press

D or l.

4.To stop scanning, briefly press

J.

5.To scan channels without Interference Eliminator

Codes, change the code for your set channel to 0

before you briefly press

J.

Note: If you press

G while the radio is scanning,

the radio will transmit on the channel you

selected before you activated Scan.

Scan List Editing

You can select the channels you want to scan by

putting those channels in a scan list.

1.To edit the scan list press

H until h is displayed.

2.Press

D or l to scroll through the list of available

channels. When you see a channel you want to add

to the list, press

H until Y is displayed to add it or

until

n is displayed to remove it.

3.Press

G to save the setting.

Voice Scrambling

This feature gives you additional privacy. Anyone who

is listening on the same channel and code will hear

distorted speech, unless they have a voice scrambling

code that matches yours. Ensure that all radios in your

group have voice scrambling enabled.

1.To turn the voice scrambling feature on, press

H

until

e is displayed, then select Y.

2.Press

G. The display will show a e.

3.To turn the Voice Scrambling feature off, press

H

until

e is displayed, then select n.

4.Press

G to exit the menu.

Hands Free Use (VOX)

VOX allows you to talk "hands

free" when used withoptional

accessories connected to the

radio.

Note: When using audio

accessories with your

radio, turn the volume of

your radio down before

you place the accessory

on your head or in your ear.

How To Use The VOX Feature

1.Switch off your radio.

2.Insert the plug of the audio accessory into the acces-

sory jack.

3.Switch on your radio. The flashing

g icon will

6864225V01_O_EN.fm Page 13 Thursday, September 16, 2004 3:50 PM

English

14

appear in the display to indicate that the VOX feature

is active.

4.To transmit, speak into the accessory microphone.

To receive, stop talking.

5.Pressing

G or removing audio accessory will dis-

able VOX operation.

Note: There is a short delay after you start talking,

before the radio transmits.

Setting the Sensitivity Level

Adjusting the VOX and/or microphone sensitivity level

helps to minimize the possibility of unintended noises

triggering a transmission, or enhances the ability to pick

up quiet voices.

If an accessory is fitted to your radio these instructions

will help you to adjust the VOX sensitivity. If no

accessory is fitted the microphone sensitivity will be

adjusted.

1.Press

H until g and a flashing number appear in

the display.

2.Select sensitivity level of 1, 2 or 3 by using

D or

l.

1 - If you speak loudly, or are in a noisy environment.

2 - Suitable for most applications.

3 - If you speak softly, or are in a quiet environment.

Note: When you connect a VOX accessory, the radio

will automatically be set to the last chosen VOX

sensitivity level.

The XTL446 also has a built in Internal Voice Operated

Transmission capability. This is a similar function to the

VOX because the sound of your voice activates

transmission, but no external accessories are needed.

Selecting the Internal VOX Feature

Either:

1.Press

H until the flashing g icon appears in the

display and the channel number is replaced with

Y

(enabled) or

n (disabled).

2.Use the up

D or down l button to select Y for

enable.

3.Press

G to select.

or:

1.Ensure radio is turned off.

2.Press and hold down

G and switch on the radio

using

j. The g icon will be shown on the display.

To Use the Internal VOX Feature

1.Quickly press and release G and the g icon will

begin to flash. Your radio will now transmit every

time you talk.

2.To disable the Internal VOX feature, press

H until

the flashing

g icon appears in the display and use

the up

D or down l button to select n for dis-

able. Or switch the radio off and then back on again.

6864225V01_O_EN.fm Page 14 Thursday, September 16, 2004 3:50 PM

15

English

Selecting Internal VOX Sensitivity

1.Ensure that the g icon is showing on the display.

2.Press

H until g and a flashing number appear in

the display

3.Select sensitivity level of 1, 2 or 3 by using

D or

l.

Vibrate

Your radio can be set to vibrate when it receives a call.

Vibrate is then suspended until 30 seconds after

channel activity has finished.

1.Press

H until B or i is displayed and then

press

D and l to select the desired setting.

Auto Power Off

You can program your radio to turn itself off after a

certain period of inactivity. This helps save battery life.

1.To set the auto power off feature press

H until

O is displayed.

2.Press

D or l to set the number of hours 1 - 8,

after which the power shuts off.

After you exit the menu,

O is displayed on the

screen. Five minutes before the radio shuts off, an alert

beep sounds followed by an alert beep every minute.

O flashes continuously during this five minute

period.

3.Select

- to turn off the auto power off feature.

Time-out Timer

The Time-out Timer feature helps extend battery life by

preventing the radio from accidentally transmitting. The

radio will emit a continuous warning tone after

G is

pressed for 60 continuous seconds and will stop

transmitting.

Keypad Lock

The keypad lock disables the H, D and l

buttons. This allows use of the J, G , k and C

buttons and to turn the radio on and off.

1.To lock or unlock the keypad press and hold the H

button for three seconds. When the radio is locked

f will show in the display.

Backlight

Your radio has a backlight which turns on when a

button is pressed and turns off automatically 4 seconds

after you last pressed a button. Backlighting can be

turned on manually by pressing

C.

Restore Factory Defaults

This returns radio to its original factory settings.

1.Hold down

G and H while switching on your

radio.

6864225V01_O_EN.fm Page 15 Thursday, September 16, 2004 3:50 PM

English

16

ALERTS

Channel Busy Indicator

The red LED will flash twice per second to indicate that

the channel is in use.

Call Tone

Your radio can transmit different call tones to other

radios, alerting users on the same channel and code

that you are about to talk. Your radio has 10 call tones

to choose from.

1.To set your call tone press

H until ^ Is displayed.

2.Press

D or l to change and hear call tones

while the setting number is flashing.

3.Press

G to set new call tone.

4.To use your call tone, press

k to transmit it to oth-

ers. The

^ will be displayed next to the channel

number.

Talk Confirmation Tone

When you turn on this feature, your two-way radio

transmits a chirp when you finish transmitting and

release the

G. It's like saying 'Roger' or 'Over', and

lets others know you've finished talking.

1.To enable or disable this tone, press and hold

D as

you turn your radio on.

6864225V01_O_EN.fm Page 16 Thursday, September 16, 2004 3:50 PM

17

English

FURTHER INFORMATION

Troubleshooting

No power or erratic display

• Reposition, replace or recharge batteries.

Message not transmitted

• Make

G

button is completely pressed while you transmit.

• Reposition, replace or recharge batteries.

• Shared channel may be in use, try another channel.

Message not received

• Confirm radios have same channel settings and interference eliminator codes

(helps minimize interference).

• Make sure

G

is not inadvertently being pressed.

• Reposition, replace or recharge batteries.

• Obstructions, and operating indoors or in vehicles may interfere with

communication. Change your location.

• Check to make sure volume is turned up.

Hearing other conversation or

noise on a Channel

• Shared channel may be in use, try another.

Limited talk range

• Steel or concrete structures, heavy foliage and use in buildings and in vehicles will

decrease range. Check for clear line of sight to improve transmission.

• Wearing radio close to body such as in a pocket or on a belt will decrease range.

Heavy static or interference

• Radios too close. Radios must be at least 1.5 metres apart.

• Radios too far apart. Obstacles interfere with transmission

6864225V01_O_EN.fm Page 17 Thursday, September 16, 2004 3:50 PM

English

18

Use and Care

To clean your radio:

• Use a soft damp cloth.

• Do not immerse in water.

• Do not use alcohol or cleaning solutions.

If your radio gets wet:

• Turn it off and remove batteries.

• Dry with soft cloth.

• Battery contacts may be wiped with a dry, lint-free cloth.

• Do not use until completely dry.

Specifications

Channels 8

Codes 38

Operating Frequency 446.00625-446.09375 MHz

Talk Range Up to 5 kilometres

Power Source

NiMH battery pack or 3 AA

alkaline batteries

Type Designation XTL446

Transmitter Power

(Watts)

0.5 ERP

Modulation Type Phase (Angle)

Channel Spacing (kHz) 12.5

6864225V01_O_EN.fm Page 18 Thursday, September 16, 2004 3:50 PM

19

English

Warranty Information

The authorized Motorola dealer or retailer where you

purchased your Motorola two-way radio and/or original

accessories will honour a warranty claim and/or

provide warranty service.

Please return your radio to your dealer or retailer to

claim your warranty service. Do not return your radio to

Motorola.

In order to be eligible to receive warranty service, you

must present your receipt of purchase or a comparable

substitute proof of purchase bearing the date of

purchase. The two-way radio should also clearly

display the serial number. The warranty will not apply if

the type or serial numbers on the product have been

altered, deleted, removed, or made illegible.

What Is Not Covered By The Warranty

• Defects or damage resulting from use of the Product in

other than its normal and customary manner or by not

following the instructions in this user manual.

• Defects or damage from misuse, accident or neglect.

• Defects of damage from improper testing, operation,

maintenance, adjustment, or any alteration or

modification of any kind.

• Breakage or damage to aerials unless caused directly

by defects in material or workmanship.

• Products disassembled or repaired in such a manner as

to adversely affect performance or prevent adequate

inspection and testing to verify any warranty claim.

• Defects or damage due to range.

• Defects or damage due to moisture, liquid or spills.

• All plastic surfaces and all other externally exposed

parts that are scratched or damaged due to normal use.

• Products rented on a temporary basis.

• Periodic maintenance and repair or replacement of

parts due to normal usage, wear and tear.

Copyright Information

The Motorola products described in this manual may

include copyrighted Motorola programs, stored

semiconductor memories or other media. Laws in the

United States and other countries preserve for

Motorola, certain exclusive rights for copyrighted

computer programs, including the exclusive right to

copy or reproduce in any form, the copyrighted

Motorola programs.

Accordingly, any copyrighted Motorola computer

programs contained in the Motorola products described

in this manual may not be copied or reproduced in any

manner without express written permission of

Motorola. Furthermore, the purchase of Motorola

products shall not be deemed to grant either directly or

by implication, estoppel, or otherwise, any license

under the copyrights, patents or patent applications of

Motorola, except for the normal non-exclusive royalty

free license to use that arises by operation of law in the

sale of a product.

6864225V01_O_EN.fm Page 19 Thursday, September 16, 2004 3:50 PM

English

20

MOTOROLA, the Stylized M Logo and all other

trademarks indicated as such herein are trademarks of

Motorola, Inc. ® Reg. U.S. Pat. & Tm. Off.

For use in:

Austria, Belgium, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungry, Iceland,

Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

Netherlands, Norway, Poland, Portugal, Slovakia,

Slovenia, Spain, Sweden, Switzerland, United

Kingdom.

@6864225V01@

6864225V01

6864225V01_O_EN.fm Page 20 Thursday, September 16, 2004 3:50 PM

Strona jest ładowana ...

Motorola XTL446 Instrukcja obsługi

Motorola XTL446 Instrukcja obsługi

w innych językach

Powiązane dokumenty

Inne dokumenty